Lower Charge Transfer Resistance Research Articles

Evaluation of electrochemical performance of antimony modified screen-printed carbon electrodes

This study compares the electrochemical performance of screen-printed carbon electrodes (SPCEs) modified with antimony (Sb/SPCEs) under different potentiostatic pre-plating conditions. Neutral Red (NR) was employed as a novel redox probe to evaluate the electrochemical performance of Sb/SPCEs. It was demonstrated that NR in the protonated form performs quasi-reversible redox transformations at bare SPCE and Sb/SPCEs in phosphate buffer solutions (pH 5.5±0.5) in the potential range of (−0.30)–(−0.75) V, where the antimony is not electroactive. Sb/SPCEs were studied electrochemically by cyclic voltammetry (CV) / electrochemical impedance spectroscopy (EIS), and morphologically by scanning electron microscopy (SEM). Cyclic voltammetry investigations revealed the dependence of the electrochemical performance of Sb/SPCEs on the degree of coverage of the substrate with the metal. The obtained CV, EIS, and SEM data are consistent. The lowest charge transfer resistance (Rct) value (6 Ω) was obtained at Sb/SPCE with the highest degree of antimony coverage. To investigate the electroanalytical performance of Sb/SPCEs, nickel (II) ions were utilized as a model analyte. A study of roughness factors and sensitivity towards nickel (II) ions for Sb/SPCEs using two-tailed Pearson's criterion revealed a high degree of correlation between their electrochemical and electroanalytical properties. The results show that using NR as a redox probe can help controlling modification processes during the development of innovative antimony-containing sensors.

Fabrication of a high-performance symmetrical supercapacitor based on electrochemically interconnected Cu:NiO@rGO:PANI/NF electrodes

A three-step electrodeposition synthesis was carried out to prepare a nanocomposite electrode of copper-doped nickel oxide and reduced graphene oxide-doped polyaniline with synergistic effects. Nickel foam was utilized as a current collector. XRD, FTIR and XPS studies confirm the molecular bond formation and molecular phase of the produced materials. According to the EDS results, the rGO:PANI/NF electrode contains 0.29 % nitrogen (N), 17.39 % carbon (C), and 9.81 % oxygen (O), while the Cu:NiO@rGO:PANI/NF electrode contains 8.24 % copper (Cu), 9.22 % carbon (C), 7.21 % oxygen (O), and 0.72 % nitrogen (N). The electrochemical performance of rGO:PANI/NF and Cu:NiO@rGO:PANI/NF electrodes were tested in a three-electrode cell with 3 M KOH aqueous electrolyte. High specific capacitances of 644.5 and 807.1 Fg−1 are achieved with the rGO:PANI/NF and Cu:NiO@rGO:PANI/NF electrodes at a current density of 20 Ag−1, respectively. The Cu:NiO@rGOPANI/NF also has a lower charge transfer resistance (RCT = 0.9 Ω) than the rGO:PANI/NF electrode (RCT = 3.8 Ω). This means NiO plays a crucial role in facilitating the transportation of charges between rGO:PANI. NiO acts as a “superhighway” that enables efficient and speedy charge transport. The expanded BET surface area of Cu:NiO@rGO:PANI/NF can be attributed to a well-interconnected network of PANI chains with NiO. In order to demonstrate a further application, an all-solid-state symmetrical supercapacitor (SSC) was then fabricated using the Cu:NiO@rGO:PANI/NF electrodes. The operating potential range is between 0 and 1.5 V. The device has a good capacitance of 81.9 Fg−1 at 4.5 Ag−1, and a capacitance retention of 97.6 % at a specific current of 10 Ag−1 after 10,000 cycles. The symmetrical device has a maximum energy density of 25.6 Wh kg−1 at a high power density of 1297.6 W kg−1 at 4.5 A g−1. In light of these results, the nanocomposite-based solid-state supercapacitor is considered to be a promising device for the development of high-performance symmetric supercapacitors.

Crafting defective ZnO nanoparticles: A green synthesis for enhanced photocatalytic degradation of organic pollutants

Surface defect engineering is a promising strategy for enhancing the number of surface-active sites to facilitate efficient redox reactions that occur on the surface of a photocatalyst. A green approach was employed to prepare urea- and choline-chloride-based deep eutectic solvent (DES) for the synthesis of ZnO/Zn(OH)2 supported by a DES complex (Zn precursor). Surface defects on ZnO nanoparticles (NPs) were tailored by decomposing the Zn precursor in air. In addition, calcination improved the crystallinity and surface-active sites of the defective ZnO by creating surface oxygen vacancies (Vo). The appearance of an Electron paramagnetic resonance peak at a g value of 1.96 confirms the formation of single-charged Vo defects on the surface of ZnO. The photocatalyst prepared at a reaction bath temperature of 75 °C (Vo-ZnO-75) showed the highest photocatalytic activity. The observed green emission in the photoluminescence spectrum and X-ray photoelectron spectroscopy analysis suggests the formation of defects on the ZnO surface. Consequently, Vo-ZnO-75 enhanced surface donor density (14.4×1020 cm−3) and lower charge transfer resistance (88.89 × 103 Ω). The optimized photocatalyst of Vo-ZnO-75 has 94% removal efficiency for rhodamine B degradation within 60 min. This study sheds new light on the development of an efficient and eco-friendly approach for preparing defective ZnO NPs for photocatalytic applications.

Preparation of Ti4O7/h‐BN self‐supported ceramic photoelectrode and its photoelectrocatalytic performance for water purification

AbstractThe construction of high‐efficiency self‐supported ceramic photoelectrode based on ideal semiconductor materials is essential for achieving effective degradation of pollutants by photoelectrocatalysis (PEC) technology. Herein, a Ti4O7/h‐BN composite ceramic photoelectrode with a unique microstructure was fabricated by a step‐by‐step calcination process and used in PEC water pollution remediation. The PEC activity of Ti4O7 ceramic photoelectrode could be enhanced by introducing hexagonal boron nitride (h‐BN) nanoparticles on the surface. The most optimized Ti4O7/h‐BN photoelectrode exhibited the decolorization rate of active brilliant blue KN‐R at about 97.79% in 30 min. The PEC activities could remain stable during five degradation cycles. The excellent photoelectrocatalytic performance of Ti4O7/h‐BN ceramic photoelectrode could be attributed to the low Tafel slope, low charge transfer resistance, large electrochemical active area, and excellent photo‐generated carrier separation efficiency. A type‐II heterojunction was formed between the Ti4O7 and h‐BN, which caused more effective carrier separation and enhanced the generation of dominant active species •O2− and h+. This work provided a mature synthesis strategy of Ti4O7/h‐BN self‐supported ceramic photoelectrodes with excellent practical application prospects to achieve superior PEC performance for water purification.

Dual-modified LiNi0.8Co0.1Mn0.1O2 cathode materials with lithium conducting hybrid oligomer and single-walled carbon nanotube for improving electrochemical performance and thermal stability of lithium-ion batteries: A novel approach for high-power and high-safety applications

In this study, we investigated the synergetic effect of a novel lithium-ion conducting hybrid oligomer [N, N′-bismaleimide-4, 4′-diphenylmethane (BMI), lithiated trithiocyanuric acid (Li-TCA) and Jeffamine®-M1000 (JA®); Li-BTJ] coating layer on a nickel-rich LiNi0.8Co0.1Mn0.1O2 (NCM811) cathode material wrapped with highly electron-conductive single-walled carbon nanotubes (SWCNTs) to enhance electrochemical performance and thermal stability for high-power and high-safety lithium-ion batteries (LIBs). Morphological analyses using scanning electron microscopy/energy dispersive spectroscopy and transmission electron microscopy showed that the NCM811 active material surface was uniformly coated with a hybrid oligomer to form NCM811@Li-BTJ, which was subsequently wrapped with SWCNTs (NCM@Li-BTJ/SWCNT composite cathode). CR2032 coin-type cells with optimized NCM811@1 wt% Li-BTJ/0.2 wt% SWCNT composite electrodes delivered a significantly enhanced capacity retention (CR) of 90.1 % relative to that of bare NCM811 electrodes (CR: 82.1 %) at 1C for 200 cycles from 2.8 to 4.3 V (vs. Li/Li+). Electrochemical impedance spectroscopy and cyclic voltammetry revealed that this superior cycling performance resulted from a lower charge transfer resistance (Rct: 96.2 vs. 324.3 Ω) and a lower polarization voltage (∆V: 0.243 vs. 0.411 V vs. Li/Li+). The in-situ micro-calorimetric results presented the total heat generation (Qt) values of the coin cells with the delithiated NCM811@Li-BTJ and NCM@Li-BTJ/SWCNT electrodes at 5C and 35 °C were substantially lower by ~9.3 % and ~ 14.6 %, respectively, compared to the bare NCM811 counterpart, indicating that the surface modifications on the NCM811 active materials could prevent the LIBs' thermal instability. Furthermore, X-ray photoelectron spectroscopy studies revealed that the Li-BTJ hybrid oligomer coating layer effectively suppressed the formation of residual Li side products such as Li2CO3 evidently on the surface of the NCM811 active material particles, thereby inhibiting undesirable side reactions. Post-mortem analyses of the dual-modified NCM811 electrode after cycling revealed that the microstructure and particle morphology of the NCM composite cathode material were extensively maintained through the synergistic effects of the Li-BTJ ion-conductive and SWCNTs electron-conductive agents.

Enhanced short-chain fatty acids production from food waste with magnetic biochar via anaerobic fermentation: Linking interfacial, extracellular, and intracellular electron transfer

Electron transfer is vital for microbial communities in anaerobic fermentation systems for food waste treatment. Considerable endeavors highlight the importance of interspecific electron transfer between acid-producing bacteria and methanogenic archaea. However, the contribution of electron transfer network from intracellular to extracellular in these microbes with conducive materials is unclear, and deserves more attention. This work demonstrated that magnetic biochar (as a typical conducive material) could enhance interfacial, extracellular and intracellular electron transfer networks during food waste fermentation, resulting in the improved production of short-chain fatty acids, accompanied by synchronous enhancements in solubilization, hydrolysis, and acidification steps. Further study revealed that magnetic biochar exhibited large surface area (28.5 m2/g) and high conductivity (97.6 μS/cm) with low charge transfer resistance and high catalytic activity, resulting in enriching acid-forming bacteria associated with electroactivity (e.g., Clostridium, Parabacteroides, and Fonticella). Also, magnetic biochar up-regulated the gene expressions involved in extracellular electron transfer, including membrane proteins (e.g., MtrA and MtrB) and conductive flagella (especially type IV pilus, e.g., PilA, PilB, and PilC), and intracellular electron transfer, particularly in the central pathway TCA cycle (e.g., acnA and sucA). In response to the evident stimulation of electron transfer networks (electron transport system activity increased by 204.1 % compared with the control), the critical gene expressions involved in fatty acid biosynthesis, requiring sufficient electrons and energy, were corresponding up-regulated (e.g., accA, accC, and accD), resulting in the promotion of short-chain fatty acids generation. This work would improve the in-depth understanding of electron transfer impacts on anaerobic systems and provide useful guidance for FW disposal.

Simultaneous and sensitive detection of ascorbic acid and uric acid using a novel MnTMPyP/LaTa2O7 nanocomposite modified glassy carbon electrode

A novel nanocomposite MnTMPyP/LaTa2O7 was synthesized via intercalation of [5, 10, 15, 20-tetrakis (N-methylpyridinium-4-yl) porphyrinato manganese (III) (MnTMPyP) into the laminar structure of RbLaTa2O7 using an ion exchange method. An electrochemical sensor utilizing a MnTMPyP/LaTa2O7 modified glassy carbon electrode (GCE) was employed for the simultaneous detection of ascorbic acid (AA) and uric acid (UA). X-ray diffractometry, Fourier infrared spectroscopy, and transmission electron microscopy were utilized to characterize the structure in this experiment. Differential pulse voltammetry (DPV), electrochemical impedance spectroscopy (EIS), and cyclic voltammetry (CV) were employed to analyze the electrochemical properties. The MnTMPyP/LaTa2O7/GCE demonstrated a larger electrochemically active area (0.106 cm2), lower charge transfer resistance (43.1 Ω), and enhanced catalytic activity compared to single-component modified electrodes (RbLaTa2O7/GCE, bare/GCE). The detection limits, within the concentration ranges of 1.25–40.41 μM for AA and 0.62–11.81 μM for UA (S/N = 3), were estimated to be 0.37 μM and 0.44 μM, respectively. MnTMPyP/LaTa2O7/GCE also exhibits excellent stability, reproducibility, and anti-interference compared to previous literatures. Furthermore, the performance of MnTMPyP/LaTa2O7/GCE was demonstrated in real urine samples, achieving recoveries between 98.7 % and 103.5 %. The ion exchange provides a simpler method for the preparation of multifunctional electrochemical sensing.

Enhancing the oxygen evolution activity and stability of Pb anode in Mn2+-containing acidic solution by embedding MnCo2O4 particles

Due to the excellent activity and stability of MnCo2O4 toward the oxygen evolution reaction (OER) in acidic solution, a Pb–MnCo2O4 composite anode for zinc electrowinning was prepared by embedding dispersed MnCo2O4 particles into a Pb matrix in a powder metallurgy process. In this work, the phase structure, chemical composition, and morphology of the oxide layers formed on Pure-Pb and Pb–MnCo2O4 were analyzed by XRD, SEM, and EDS. Galvanostatic polorization, Tafel tests, and EIS measurements were performed to investigate the anodic potential variation and OER kinetics of the Pure-Pb and Pb–MnCo2O4 composite anodes. Compared with that on the Pure-Pb anode, the oxide layer on Pb–MnCo2O4 is thinner, more compact, and more stable in a 160 g L−1 H2SO4 solution containing 4 g L−1 Mn2+. Consequently, the Pb–MnCo2O4 composite anode exhibited a much lower anode slime production (8.7 mg) during 72 h of the simulated zinc electrowinning process. Despite the smaller surface area and lower PbO2 content of the oxide layer, the Pb–MnCo2O4 composite anode presented preferable OER kinetics with a lower OER charge transfer resistance (0.729 Ω cm2) and a smaller Tafel slope (90.74 mV dec−1), which contributed to a 70 mV reduction in the anodic potential compared with that of the Pure-Pb anode.

GO modification with PANI-PpPDA as support material for Pd-Ni and its application for ethanol electrooxidation

Among different renewable energy sources, fuel cells emerged to be a promising solution. However, due to limitations such as high cost and low stability of current commercial catalysts, several approaches are considered to modify them. Graphene oxide (GO) modification via a facile in-situ polymerization of aniline (ANI) and p-phenylenediamine (pPDA) in the presence of GO sheets is the main goal of this study. Pd and Ni as active metals are chemically deposited on the support material. The prepared substrates and catalysts are examined by various structural and electrochemical tests. This study shows that GO-PANI-PpPDA support material has favorable characteristics with 32.64 % higher surface area compared to GO. High surface area and porosity lead to more loading and uniform distribution of metallic particles. GO-PANI-PpPDA/Pd-Ni exhibited superior eligible properties including 29.28 % higher electrochemically active surface area compared to GO/Pd-Ni. This nanohybrid has the lowest charge transfer resistance, highest current density, stability and durability and it loses 5.67 % of the initial current after 15 h. This method shows promising results as an advanced strategy to synthesize low-cost and high-performance Pd-based electrocatalysts on the modified GO.

Double-sided semitransparent titania photoelectrode with enhanced light harvesting

In this work, unique semitransparent electrodes were prepared by the anodization of titanium layers (540 nm thick) initially deposited on the both sides of glass substrates employing indium-tin oxide interface layers serving as a current collector for the induced photocurrent. The anodization strategy used in this study enables fabrication of semitransparent titanium dioxide nanotube arrays with either aligned or spaced architecture on the two sides of the planar substrate. This study aims to perform a detailed investigation of this novel photoelectrode system (crystal structure, morphology and optical properties) to reveal their photoelectrochemical features. It was found that the photoelectrode exhibits enhanced photocurrent density about 1.9 times higher (4.6 μAcm−2 at +0.5 V) for aligned nanotubes compared to a substrate overgrown symmetrically by separated nanotubes (2.4 μAcm−2 at +0.5 V). This can be effectively explained by the higher tube density in the case of aligned nanostructures, which provide more channels for charge percolation. In addition, both the high donor concentration (6.4 × 1020 cm−3) together with the low charge transfer resistance of the semitransparent electrode of the aligned nanotubes make the material promising for application in photoelectrochemical systems and smart light management.

Role of Salt Concentration in Stabilizing Charged Ni-Rich Cathode Interfaces in Li-Ion Batteries.

The cathode-electrolyte interphase (CEI) in Li-ion batteries plays a key role in suppressing undesired side reactions while facilitating Li-ion transport. Ni-rich layered cathode materials offer improved energy densities, but their high interfacial reactivities can negatively impact the cycle life and rate performance. Here we investigate the role of electrolyte salt concentration, specifically LiPF6 (0.5-5 m), in altering the interfacial reactivity of charged LiN0.8Mn0.1Co0.1O2 (NMC811) cathodes in standard carbonate-based electrolytes (EC/EMC vol %/vol % 3:7). Extended potential holds of NMC811/Li4Ti5O12 (LTO) cells reveal that the parasitic electrolyte oxidation currents observed are strongly dependent on the electrolyte salt concentration. X-ray photoelectron and absorption spectroscopy (XPS/XAS) reveal that a thicker LixPOyFz-/LiF-rich CEI is formed in the higher concentration electrolytes. This suppresses reactions with solvent molecules resulting in a thinner, or less-dense, reduced surface layer (RSL) with lower charge transfer resistance and lower oxidation currents at high potentials. The thicker CEI also limits access of acidic species to the RSL suppressing transition-metal dissolution into the electrolyte, as confirmed by nuclear magnetic resonance (NMR) spectroscopy and inductively coupled plasma optical emission spectroscopy (ICP-OES). This provides insight into the main degradation processes occurring at Ni-rich cathode interfaces in contact with carbonate-based electrolytes and how electrolyte formulation can help to mitigate these.

Construction of Z-type In2O3@InP heterostructure with enhanced photo-assisted electrocatalytic water splitting for hydrogen production

We report an in-situ construction strategy of Z-type In2O3@InP hydrogen evolution reaction (HER) electrocatalyst with well-defined core-shell structure on nickel foam (In2O3@InP/NF) via sequential hydrothermal, annealing, and phosphating steps. The phosphating time dramatically affects the morphology, crystal phase, elemental composition, and optical properties of In2O3@InP. The resulting electrode obtained with 2 h of phosphating time has smaller overpotentials and Tafel slope, larger TOF and ECSA, and lower charge transfer resistance compared to In2O3/NF. The better activity reveals the promoted roles of InP that can provide more active sites, facilitate charge transfer, and accelerate the adsorption of H* species. The photo-assisted electrocatalytic activity for HER is significantly enhanced attributed to the strong light absorption capacity of InP, superior energy level configuration of In2O3 and InP, and excellent transient light response of In2O3@InP. Furthermore, the electrode has favorable stability and durability, and the morphology and surface chemical state have no essential changes after the photo-assisted HER stability test.

Study on effect of surface engineering by In doped CeCu2O4 for enhanced super capacitive properties as energy storage solution

This research study focuses on the utilization of indium-doped cerium copper oxide as electrode materials to augment super capacitive properties. Hydrothermal method was employed to successfully synthesize both pristine CeCu2O4 and CeCu2O4 doped with varying concentrations of indium (1 %, 3 %, and 5 %). Indium doping induced alterations in the crystal structure and modified the morphology of CeCu2O4 flakes, that lead to the development of a network-like structure. Notably, the electrode material comprising 3 % indium-doped CeCu2O4 exhibited a significantly increased specific surface area of 151.2 (m2/g), which provided an abundance of enhanced active sites on its surface. Electrochemical experimental results revealed that the 3 % indium-doped CeCu2O4 electrode material demonstrated greater electrochemical functioning. It exhibited a specific capacitance (Cs) of 1082 F/g and 740 at a current density of 1 A/g and 1.5 A/g in 3 and 2-electrode configurations, respectively. Calculated from CV analysis resulted in Cs values of 374 F/g and 313 F/g at a scan rate of 10 mV/s in 3 and 2-electrode configurations, respectively. Furthermore, it displayed 33.3 Wh/kg energy density (Ed) and maintained a retention rate of 74.7 % after 50 h of testing, as well as exhibiting a lower charge transfer resistance (Rct) of 12.02 Ω and 23.2 Ω in 3 and 2-electrode configuration. Due to its outstanding specific capacitance, prolonged durability, and reduced resistance, the 3 % indium-doped CeCu2O4 electrode material emerges as a suitable contender for advanced supercapacitor uses for the next generation.

Facile synthesis of Co-Cu metal organic framework as efficient non-noble bifunctional electrocatalysts for overall water splitting

The rapid development of superior, highly stable, alkaline-medium-compatible, and nonprecious earth-abundant bifunctional electrocatalysts has garnered significant research interest. This interest aims to replace the costliest noble metals (Pt, Ir/IrO2, and Ru/RuO2) in renewable and green energy technologies for overall water splitting. However, there are still important limitations, such as lower stability and higher energy consumption. In this work, we report the synthesis of Cu-Co metal-organic frameworks (MOFs) as a bifunctional electrocatalyst using a simple chemical precipitation technique. Especially, when 11.5 mM of Co is combined with Cu MOF, it exhibits excellent bifunctional activity for overall water splitting with a lower overpotential of 0.21 V (OER) and -0.71 V (HER) at a current density of 10 mA cm−2, which exhibits nearly several times more enhancement than that of pristine Cu and Co MOFs in a 1 M KOH electrolyte solution. The Tafel slope value of 130 mV/dec and the lower charge transfer resistance, along with relatively high stability for up to 12 h at the onset potential of OER and HER, are observed for the 11.5 mM Cu-Co MOF electrocatalyst. The present results open an alternative pathway for developing a novel design of highly efficient and scalable bifunctional electrocatalysts for overall water splitting.

Coupling harmful algae derived nitrogen and sulfur co-doped carbon nanosheets with CeO2 to enhance the photocatalytic degradation of isothiazolinone biocide

Removing the algae from water bodies is an effective treatment toward the worldwide frequently occurred harmful algae blooms (HAB), but processing the salvaged algae waste without secondary pollution places another burden on the economy and environment. Herein, a green hydrothermal process without any chemical addition was developed to resource the HAB algae (Microcystis sp.) into autogenous nitrogen and sulfur co-doped carbon nanosheet materials C–CNS and W–CNS, whose alga precursors were collected from pure culture and a wild bloom pond, respectively. After coupling with CeO2, the obtained optimal C–CNS/CeO2 and W–CNS/CeO2 composites photocatalytically degraded 95.4% and 88.2% of the marine pollutant 4,5-Dichloro-2-n-octyl-4-isothiazolin-3-one (DCOIT) in 90 min, significantly higher than that of pure CeO2 (63.15%). DCOIT degradation on CNS/CeO2 was further conducted under different conditions, including pH value, coexisting cations and anions, and artificial seawater. Although different influences were observed, the removal efficiencies were all above 76%. Along with the ascertained good stability and reusability in five consecutive runs, the great potential of CNS/CeO2 for practical application was validated. UV–vis DRS showed the increased light absorption of CNS/CeO2 in comparison to pure CeO2. PL spectra and photoelectrochemical measurements suggested the lowered charge transfer resistance and thereby inhibited charge recombination of CNS/CeO2. Meanwhile, trapping experiments and electron paramagnetic resonance (EPR) detection verified the primary roles of hydroxyl radical (OH) and superoxide radical (O2−) in DCOIT degradation, as well as their notably augmented generation by CNS. Consequently, a mechanism of CNS enhanced photocatalytic degradation of DCOIT was proposed. The intermediates involved in the reaction were identified by LC-QTOF-MS, giving rise to a deduced degradation pathway for DCOIT. This study offers a new approach for resourceful utilization of the notorious HAB algae waste. Besides that, photocatalytic degradation has been explored as an effective measure to remove DCOIT from the ocean.

Phosphomolybdic acid regulated the defective metal-organic framework UiO-66 for electrochemical nitrogen reduction reaction

In recent years, electrochemical ammonia synthesis has been considered a green process with excellent application prospects. The nitrogen reduction process (NRR) needs more activation energy when NN bonds are broken, which decreases the ammonia yield rate and Faraday efficiency (FE) for ammonia synthesis. Herein, UiO-66-xHPMo electrocatalysts are effectively synthesized by regulating the defects of the metal-organic framework (UiO-66) using phosphomolybdic acid (HPMo) as a defect regulator. XRD, FT-IR, TEM, XPS, TPD, etc., characterized the catalysts. As a result, the reasons for the increase in NH3 yield rate (RNH3) are catalysts losing the ligand of terephthalic acid, exposing more Zr6 nodes as active sites, and providing numerous active sites for NN cleavage. However, introducing HPMo makes catalysts more alkaline and have lower charge transfer resistance, which are more inclined to adsorb H+ and enhance hydrogen evolution reaction (HER), reducing FEs. Thus, with a voltage of −0.3 V (vs. RHE) and a neutral electrolyte (0.1 mol L−1 Na2SO4), UiO-66–2HPMo has excellent NRR performance (RNH3: 36.61 μg h−1 mg−1, FE: 31.09%).

Highly efficient metal free aldehyde-functionalized indoles for direct glucose fuel cell anode catalyst

In this study, alternative organic catalysts to metal-containing catalysts for glucose electrooxidation were prepared by the Suzuki Miyaura coupling reaction method and characterized by nuclear magnetic resonance (NMR), fourier transform infrared spectroscopy (FT-IR), and liquid chromatography with tandem mass spectrometry (LC-MS-MS). InTA-1, InPA-1, InFA-1, InTA-2, InPA-2, InFA-2, InTA-3, InFA-3, and InPA-3 were obtained with the yield of 74%, 82%, 72%, 70%, 75%, 68%, 60%, 71%, and 85%. Among the synthesized catalysts, the InTA-3 catalyst possesses the highest electrocatalytic activity (3.17 mA cm−2) and long-term stability compared to other organic catalysts. InTA-3 catalyst has the lowest charge transfer resistance toward glucose electrooxidation. It was concluded that as a metal-free catalyst, InTA-3 is a cheap and promising electrocatalyst for direct glucose fuel cell anode.

Synthesis of MFe2O4 (M=Ni, Co) Nanoparticles by a Bicontinuous Microemulsion Method for the Oxygen Evolution Reaction

AbstractDeveloping efficient and low‐cost electrocatalysts for the oxygen evolution reaction (OER) is crucial for sustainable hydrogen production through water splitting. In this study, CoFe2O4 and NiFe2O4 nanoparticles as electrocatalysts were prepared via an inexpensive method involving the use of bicontinuous microemulsions as nanoreactors. The crystalline structure, morphology, and elemental composition of the electrocatalysts were characterized by XRD, Raman spectroscopy, TEM, and EDS elemental mapping. The electronic structure and textural properties were examined using XPS and the nitrogen adsorption‐desorption method. The OER measurements were carried out in a standard three‐electrode system. CoFe2O4 demonstrated relatively higher OER catalytic activity than NiFe2O4 in 1 M KOH solution, with a smaller overpotential of 410 mV to achieve a current density of 10 mA cm−2 and a smaller Tafel slope of 80 mV dec−1. In contrast, NiFe2O4 offered a higher overpotential of 450 mV to reach the same current density. The superior performance of CoFe2O4 is ascribed to higher ECSA, better conductivity, and lower charge transfer resistance. However, both electrocatalysts showed stability up to more than three hours of continuous performance.

Highly electrochemically active Ti3C2Tx MXene/MWCNT nanocomposite for the simultaneous sensing of paracetamol, theophylline, and caffeine in human blood samples.

Thefacile fabrication is reportedof highly electrochemically active Ti3C2Tx MXene/MWCNT (3D/1D)-modified screen-printed carbon electrode (SPE) for the efficient simultaneous electrochemical detection of paracetamol, theophylline, and caffeine in human blood samples. 3D/1D Ti3C2Tx MXene/MWCNT nanocomposite was synthesized using microwave irradiation and ultrasonication processes. Then, the Ti3C2Tx/MWCNT-modified SPE electrode was fabricated and thoroughly characterized towards its physicochemical and electrochemical properties using XPS, TEM, FESEM, XRD, electrochemical impedance spectroscopy, cyclic voltammetry, and differential pulse voltammetry techniques. As-constructed Ti3C2Tx-MWCNT/SPE offers excellent electrochemical sensing performance with good detection limits (0.23, 0.57, and 0.43µM) and wide linear ranges (1.0 ~ 90.1, 2.0 ~ 62.0, and 2.0-90.9µM) for paracetamol, caffeine, and theophylline, respectively, in the human samples. Notably, the non-enzymatic electroactive nanocomposite-modified electrode has depicted a semicircle Nyquist plot with low charge transfer resistance (Rct∼95 Ω), leading to high ionic diffusion and facilitating an excellent electron transfer path. All the above results in efficient stability, reproducibility, repeatability, and sensitivity compared with other reported works, and thus, it claims its practical utilization in realistic clinical applications.

Optimizing energy storage: Carbon implantation in NiO matrix unveils C–NiO's hybrid capacitive and battery-like behavior with enhanced electrochemical performance

Doping is a common strategy employed to enhance material properties. Numerous researchers have introduced carbon into the nickel oxide (NiO) matrix through various methods to improve the electrochemical performance for energy storage applications. This study investigates the impact of carbon implantation into the NiO matrix using a particle accelerator. Cyclic voltammetry profiles of carbon-implanted NiO (C–NiO) reveal distinct oxidation–reduction peaks, and one side of the CV curves exhibits a rectangular shape, confirming the hybrid capacitive and battery-like behavior of C–NiO. The reduced separation between oxidation–reduction peaks and the increased specific capacitance at higher scan rates validate the capacitive nature of C–NiO. Enhanced electrochemical performance was further explored through GCD, EIS, and BET techniques. C–NiO demonstrates impressive capacitance retention of 93.8 % after 5000 cycles. The Nyquist plot indicates that the improved performance of C–NiO is attributed to its heightened electrode activity, resulting from lower charge-transfer resistance. BET analysis confirms that C-doping leads to a larger surface area. In the NiO matrix, two bands of adsorbed CO2 are observed, whereas these bands are absent in C–NiO, indicating clearer pathways for ion–electron exchange. Compared to undoped NiO (55 F/g at 50 mV/s), C–NiO exhibits a more than tenfold increase in specific capacitance (1079 F/g at 50 mV/s).