Lower Charge Transfer Resistance Research Articles

Marigold flower-like structured battery-type Cu2O/Co(OH)2 composite electrode material for high-performance supercapacitors

Addressing the limitations of individual Cu2O and Co(OH)2 components, this study aims to develop a high-performance supercapacitor electrode by synergistically combining these materials. A composite electrode material of Cu2O/Co(OH)2 was effectively synthesized on nickel foam via a facile hydrothermal method for supercapacitor applications. The as-fabricated Cu2O/Co(OH)2 composite electrode exhibits a hierarchical marigold flower-like morphology that comprises of many interspersed nanoflakes. This unique morphology offers several advantages, including increased surface area, abundant electroactive sites, and enhanced electrolyte accessibility, all of which contribute to superior electrochemical performance. The Cu2O/Co(OH)2 electrode demonstrates exceptional battery-type supercapacitor behavior, characterized by prominent redox peaks in cyclic voltammetry curves and a well-defined potential plateau during galvanostatic charge-discharge measurements. The electrode delivers an outstanding specific capacitance of 90.21 mA h g⁻1 at a current density of 1.25 A g⁻1 and retains a remarkable 81.91 % capacitance at a high current density of 12.5 A g⁻1. Furthermore, the electrode exhibits impressive cycling stability, maintaining approximately 107.84 % of its initial specific capacity value after 200 cycles at 7.5 A g⁻1. Electrochemical impedance spectroscopy measurements reveal low solution resistance and charge-transfer resistance, signifying efficient charge-transfer kinetics within the electrode. These findings highlight the potential of Cu2O/Co(OH)2 composite electrodes as promising candidates for high-performance supercapacitor applications.

ZnO/NiFe2O4 heterostructure on nickel foam for the electrochemical detection of uric acid

In this study, heterostructures containing hydrothermally derived ZnO and combustion derived NiFe2O4 were co-deposited on nickel foam (NF) substrate. The modification of NF based substrate with the synthesised electrocatalysts is capable of increasing the electrochemically active surface area (ECSA) due to its porous network. The fabricated ZnO@NF, NiFe2O4@NF and ZnO/NiFe2O4@NF electrodes were tested in phosphate buffer saline (PBS) (pH = 7.4 ± 0.2) to understand their chemical kinetics which reveals a diffusion-controlled process. A comparative study reveals that the presence of surface charges on ZnO/NiFe2O4@NF electrode, influences the selectivity by enhancing the sensitivity towards UA which is attributed to the low charge transfer resistance and its higher ECSA of 1.487 cm2. The linear response current was observed between 0.52 mM and 1.48 mM with a detection limit (LOD) of 8.22 μM and limit of quantification (LOQ) of 27.4 μM. The sensitivity was found to be 2.31 mA.mM−1cm−2. The main advantages of ZnO/NiFe2O4@NF electrode is its simple fabrication technique which is inexpensive, stability over a period of 13 days with current loss of ∼19.2 %. The proposed ZnO/NiFe2O4 based non-enzymatic UA sensor is capable of selectively detecting UA in the presence of various interferents. UA acts as a biomarker for the diagnosis of different stages of chronic kidney disease (CKD). Hence, the validity of the developed heterostructure was investigated for real time UA sensing using spot urine samples. The recovery percentage was found to be between 95.7 % and 103.5 % further paving way for the use of this electrode for diagnosis of CKD.

Hierarchical design of self-standing FeNi-based metallic glass by in-situ surface amorphous oxide construction for durable and efficient oxygen evolution

As the driving force to accelerate water electrolysis in commercialization, electrocatalysts concurrently satisfying electrocatalytic activity, mechanical flexibility and low cost are essential in the design to lower the kinetic barriers of oxygen evolution reaction (OER). Herein, we present a strategy to in situ construct amorphous metal oxide nanolayers on different compositions of self-standing non-precious FexNiyP20 (at.%) metallic glasses (AMO-MG). With the mechanical flexibility, the processed FexNiyP20 MGs, particularly at Fe30Ni50P20, reaches low OER overpotentials of 238 at a current density of 10 mA cm−2 and a Tafel slope of 33 mV dec−1 in 1.0 M KOH solution while preserving a long-term durability exceeding 60 h. Further studies indicate these robust OER activities appear to be directly linked with the unique surface patterns of the in situ formed AMO nanolayer providing abundant active sites, low charge transfer resistance and superior structural-integration. Modelling analysis further shows that both Fe and Ni sites in the AMO nanolayer act as active sites leading to a strong charge transfer for effective H2O adsorption and an optimization of rate-determining step of OER process. Such in situ AMO-MG hierarchical structure therefore provides a novel structure-integration strategy and win–win situation to design and commercialize high-performance alloy catalysts for OER.

Hedgehog Zinc Oxide-Graphene Quantum Dot Heterostructures as Photocatalysts for Visible-Light-Driven Water Splitting.

The development of efficient photocatalysts for sustainable hydrogen production via water splitting is vital for advancing renewable energy technologies. In this study, we present the synthesis and characterization of a novel visible-light-active photocatalyst comprising hedgehog-shaped zinc oxide (ZnO) nanostructures coupled with graphene quantum dots (GQDs). Optical properties assessed by UV-visible and photoluminescence (PL) spectroscopy revealed that the ZnO/GQDs heterostructure possessed a reduced band gap (2.86 eV) compared with pristine ZnO (3.10 eV), resulting in improved light absorption and charge separation. Electrochemical analyses indicated a significantly higher photocurrent response and lower charge transfer resistance for the ZnO/GQDs heterostructure compared with the pristine ZnO nanostructure. Photocatalytic tests demonstrated that the ZnO/GQDs heterostructure achieved over 3-fold higher hydrogen (H2) production rates, with an apparent quantum yield (AQY) of 1.51% at 440 nm, and maintained stable activity over prolonged reaction periods. These results highlight the enhanced photocatalytic efficiency and stability of the ZnO/GQDs heterostructure, underscoring its potential as a high-performance photocatalyst for sustainable hydrogen generation. The synergistic effects between ZnO nanostructures and GQDs offer valuable insights into the design of advanced photocatalytic materials for renewable energy applications.

Interface engineering of laminated redox-copolymers for electrochemical remediation of perfluoroalkyl substances

Redox polymers now show promise for selective removal of perfluoroalkyl substances from a complex aqueous matrix at high energy efficiency and no secondary pollution. However, self-agglomeration of redox polymers is a dominating barrier to constructing a low-cost, stable system in practical applications. Herein, we introduce polymer interface engineering strategy to enhance the activity of amine functionalities and nitrous oxide radicals in copolymers composed of 4-methacryloyloxy-2,2,6,6-tetramethylpiperidin-1-oxyl and 4-methacryloyloxy-2,2,6,6-tetramethylpiperidine. The grafted laminated redox polymer on multi-walled carbon nanotubes (termed MWCNT-g-P(TMPMA-co-TMA)) via free-radical polymerization demonstrated a 19.1–59.9 % increase in the electrosorption capacity with a maximum value (Qm) of 725.09 mg g−1 and a pseudo-first-order rate constant k1 = 1.46 min−1 and sustainable regeneration efficiency at ∼80 %. The core–shell structure of MWCNT-g-P(TMPMA-co-TMA) with a laminated redox polymer layer of ∼5 nm processed a low charge transfer resistance, which is expected to contribute to the enhanced capture performance and stability. An integrated system consisting of a MWCNT-g-P(TMPMA-co-TMA) electrode and a boron-doped diamond electrode can efficiently separate and degrade trace-concentration PFOA from industrial wastewater at high mineralization efficiency. This work provides insight into the design and optimization of redox active materials for water purification and beyond.

Synergistic Enhancements of Zn-ZIF with Nano Zinc Oxide for Hydrogen adsorption, energy storage, and photocatalytic technologies

Creating the porous Zinc-Zeolitic Imidazolate Framework (Zn-ZIF) using a solvothermal technique addresses the need for advanced materials with distinctive properties and cost-effectiveness in modern applications. The PXRD, SEM, UV-DRS, TEM, and TGA/DTG are used to characterize different concentrations of Zn-ZIF. Zn-ZIF's crystalline structure and phase purity have been verified by PXRD. Using diffuse reflectance spectra, the Kubelka-Monk function determined the band gaps of the Zn-ZIF samples, and scanning electron microscopy revealed a more porous structure. At 77 K and 1 bar, the Zn-ZIF solution with a 2:1 ratio had the highest hydrogen storage capacity (1.71 wt%). The electrochemical behavior of several Zn-ZIF electrodes in a 6 M KOH electrolyte was evaluated by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) experiments. The Zn-ZIF electrode with a 2:1 ratio exhibits a low charge transfer resistance and a high proton diffusion coefficient (D) of 1.687 × 10−4 cm2 s−1. The characteristics of the 2:1 synthesized Zn-ZIF electrode as a supercapacitor were investigated. Our analysis of the generated Zn-ZIF material's specific capacitance values after 2000 cycles revealed an impressive retention rate of nearly 89 %, with values of 296.6 Fg-1. In addition, we examined the photocatalytic activities of the as-synthesized material by exposing it to ultraviolet light and seeing how it degraded organic dyes such as Cango-Red (CR) dye. With a photocatalytic efficacy of 95.06 % for CR dye, Zn-ZIF (2:1 ratio) is the most effective. These findings should provide new knowledge for researchers interested in developing novel Zn-ZIF materials for photocatalytic, energy storage, and hydrogen storage applications.

Selective electro-capacitive deionization of Yb(III) by nanospherical N-doped carbon supported nickel‑iron bimetallic oxide, nitride and phosphide

The separation of rare earth elements from the mining waste water is highly important but still facing challenge. In this study, three different porous composite electrode materials were well-designed by decorating the nickel‑iron bimetallic oxide, nitride or phosphide onto nitrogen-doped carbon nanosphere, respectively (termed as NiFeO@NC, NiFeN@NC and NiFeP@NC), and utilized in capacitive deionization device for electrosorption of Yb(III) from water under the low-voltage electric field. The characterization and electrochemical results indicated that the incorporation of N or P atom lead to the reduced specific surface area and the enhanced electrochemical properties (i.e., larger specific capacitance, lower charge transfer resistance). In addition, NiFeN@NC and NiFeP@NC exhibited the excellent electrosorption capacities of Yb(III) with 105.24 mg·g−1 and 90.31 mg·g−1, respectively, under conditions of a flow rate of 20 mL·min−1, a voltage of 1.2 V, and pH of 5.0, which was extremely higher than NiFeO@NC (i.e., 50.7 mg·g−1). Moreover, all these three materials also demonstrated the remarkable electrosorption selectivity of Yb(III) from the mixed solution, and the robust durability with over 90 % of initial capacities after ten consecutive electrosorption-desorption cycles. Furthermore, the XPS characterizations and electrosorption results revealed that the electrosorption mechanism mainly depended on the synergistic effects of intrinsic Faraday redox reaction, electric double layer capacitance and active binding sites. Therefore, this work provided a feasible strategy for the separation of rare earth elements from aqueous solution, and the prospective applications related to the recovery of rare earth elements from mining wastes or spent permanent magnets in future life.

Reversible Li-ion trade-off in ultrathick sulfur cathodes for practical lean Li–S batteries

The use of low electrolyte volume is beneficial to improve energy density but severely limits access over obscured sulfur, along with sluggish ion kinetics and aggravated polarization, as the ion imbalance across the multicomponent interface of thick sulfur cathodes at a lean electrolyte viciously dominates the sulfur electrokinetics. Herein, we demonstrate that an ion imbalance at the interfaces of a thick electrode with a lean electrolyte can be compensated by the ion trade-off strategy utilizing a cationic ion conductive active binder. It ensures sustained lithium-ion donation/release over the vicinity of slow electrolyte percolation to realize an ion-enriched sulfur–binder–electrolyte interface. The in-situ evolved ionic interface essentially activates the inaccessible sulfur, bringing about additional capacity and low ion and charge transfer resistances. The active binder adopts sulfur cathodes housing 8.1 mg cm–2 with an E/S ratio of 6 µL mg–1 electrochemically utilized 60.89 % sulfur, corresponding to a 1020 mAh g–1 capacity. The lean Li–S pouch cell delivers an energy density of 324 Wh kg–1, demonstrating the efficacy of ion trade-off to ease the interfacial barrier. This study would open up a new paradigm in potentially designing thick electrodes for multiple high energy density batteries.

Development of novel plasma process for modification of solid and liquid interfaces for high-energy-density Cu-MnOx supercapacitor electrodes

Supercapacitors are known for their fast-charging capabilities and high-power density, though their energy density is lower compared to common batteries. Modifying the interface of manganese oxide (MnOx) electrodes by incorporating copper (Cu) is a promising method to enhance the energy density of supercapacitors, though it is not yet fully implemented due to the high electrical resistance inherent to MnOx. This work addresses this challenge by incorporating copper oxide into MnOx. A custom-designed atmospheric-pressure plasma device is used to induce super-hydrophilicity in the carbon cloth substrate, thereby improving MnOx electrodeposition. The copper sulfate precursor solution is also treated with direct plasma discharge to increase the copper doping rate in MnOx. The resulting Cu-MnOx supercapacitor electrodes, with copper oxide incorporated into the material, exhibit significantly lower charge transfer resistance and impedance, indicating an improved electrolyte/electrode interface. The assembled asymmetric supercapacitor, featuring Cu-MnOx as the cathode and activated carbon as the anode, demonstrates a specific capacitance of 92.3 F/g at 1 A g-1, a power density of 700 W/kg, and an energy density of 25.13 Wh/kg. This approach is promising for developing next-generation plasma processing technologies and energy storage materials and devices, as well as easy-to-implement surface modifications for improved wettability.

Performance evaluation of a dynamic electrooxidation systems with magnetically functionalised UiO-66-NH2 and Ti/Sb–SnO2 for methotrexate treatment

Novel conductive MOF magnetic particles Fe3O4@UiO-66-NH2@PANI (FUP) were prepared and combined with Ti/Sb–SnO2 electrodes to construct a dynamic system with improved electrochemical oxidation efficiency. Electrochemical tests revealed that the Ti/Sb–SnO2–FUP electrodes showed a high active specific surface area and low charge transfer resistance. Investigation of the effects of parameters such as dynamic particle loading, magnetic separation time, initial concentration, Na2SO4 dosage and solution pH on the methotrexate (MTX) degradation rate revealed that the degradation rate reached 97.5%. Electron paramagnetic resonance spectroscopy revealed that the Ti/Sb–SnO2–FUP electrodes could produce abundant hydroxyl radicals, possibly due to the unique pore structure of UiO-66-NH2 and the semiconductor structure of aniline. Finally, the decomposition pathway of MTX and ecotoxicity of the intermediates were analysed through LC-MS/MS and Toxicity Estimation Software Tool theoretical calculations combined with genotoxicity experiments. The results showed that Ti/Sb–SnO2–FUP could effectively reduce the toxicity of the intermediates. In this work, a dynamic electrooxidation system was developed using magnetic Ti/Sb–SnO2 electrodes coupled with MOFs, providing a new idea to improve the oxidative degradation efficiency of electrooxidation systems.

Development of carbon dots supported on Zr-MOFs nano-composites for effective oxygen evolution reaction

Efficient hydrogen generation from water splitting is a key component of the hydrogen economy. It has been extensively researched for decades how electrochemically splitting water using electrocatalysts might provide a sustainable and environmentally friendly hydrogen energy source. Sluggish kinetics of the oxygen evolution reaction (OER) hinders the process of overall water splitting. Although metal-organic frameworks (MOFs) are attractive for generation of effective OER electrocatalysts, their activity is significantly hindered by their inherent lower conductivity. Here, we demonstrate a Zr-MOF-based composite with carbon dots (CDs) in order to increase their OER activity. Its exceptional morphology with higher porosity and greater surface area results in enhanced electrochemical activity. It reveals tremendously low onset potential, i.e., 1.40 V vs. RHE, and a remarkably small overpotential of 1.45 V vs. RHE to attain benchmark current density. It exhibited a minimal Tafel value of 37 mV/dec, conquering state-of-the-art catalysts for OER. The fabricated electrocatalyst demonstrated a lower charge transfer resistance (Rct) of 0.248 Ω, with exceptional durability for about 20 h in chronoamperometric studies and for up to 1500 CV cycles. All these results demonstrated that as-fabricated Zr-MOF-based composite is a probable and potential candidate for OER.

Fabrication of Ti/Zr-SnO2/PbO2-Nd Electrode for Efficient Electrocatalytic Degradation of Alizarine Yellow R

Introduction: A novel attempt to degrade alizarine yellow R (AYR) by lead dioxide (PbO2)/ neodymium (Nd) coated Ti anode was investigated. Method: Ti/Zr-SnO2/PbO2-Nd electrode showed high oxygen evolution potential, high current density, and neutral conditions, which favored the degradation of AYR. The PbO2-Nd layer on Ti/Zr-SnO2 was further characterized by scanning electron microscopy, and X-ray diffraction analysis, and X-ray photoelectron spectroscopy. The electrochemical properties of Ti/Zr- SnO2/PbO2-Nd electrode were evaluated by cyclic voltammetry, AC impedance spectroscopy, and accelerated life test. Result: The relatively higher oxygen evolution overpotential (~1.80 V) of the developed electrode can effectively suppress the occurrence of surface side reactions and oxygen evolution. A relatively lower charge transfer resistance (Rct, 18.0 Ω) of Ti/Zr-SnO2/PbO2-Nd electrode could be found. The Ti/Zr-SnO2/PbO2-Nd electrode exhibited an accelerated lifetime of 110 min under a very high current density of 10,000 A/m2. The doping of Nd could produce loosely-stacked sheet-like structures, thus, the number of active sites on the electrode surface increases. Conclusion: Moreover, an outstanding conductivity of Ti/Zr-SnO2/PbO2-Nd electrode was obtained, which favored the electron transfer and catalytic activity of the modified electrode. The Ti/Zr-SnO2/PbO2-Nd electrode exhibited improved electrochemical performances and higher oxygen evolution potential, and the highest oxygen evolution potential is 1.80 V. Under the current density of 30 mA/cm2, the electrocatalytic degradation of 92.3% could be achieved in 180 min. The electrochemical oxidation of AYR at the Ti/Zr-SnO2/PbO2-Nd electrode proved to be feasible and effective, indicating that it might be used for the elimination of AYR from wastewater. conclusion: The electrochemical oxidation of AYR at the Ti/Zr-SnO2/PbO2-Nd electrode proved to be feasible and effective, indicating that it might be used for the elimination of AYR from wastewater.

Bio-functionalized conductive poly(acrylic acid):poly(3,4-Ethylenedioxythiophene)-Prussian blue hybrid transducer for biosensors and bioelectronics interfaces

This study presents an innovative organic-inorganic hybrid transducer of poly(acrylic acid) (PAA), poly(3,4-ethylenedioxythiophene) (PEDOT) and Prussian blue (PB) nanocatalysts. The transducer demonstrated functionality conducive to enzyme conjugation and exhibited favorable electrochemical properties for biosensor signal transduction. Fabricated by a one-tube chemical redox method, the PAA:PEDOT-PB transducer showed long-term electrocatalytic and structural stability. The performance of the transducer was characterized by high transduction activity and low charge transfer resistance, particularly for H2O2 reduction. It achieves a linear detection range from 1.0 μM to 4.0 mM, with a sensitivity of 494 ± 10 μA mM−1 cm−1 and a LOD of 0.34 μM. The PAA:PEDOT-PB transducer featured a high density of carboxyl groups (DCOOH = 14.64 ± 0.05 μmol cm−2) that promoted the immobilization of the H2O2-dependent oxidase enzyme lactate oxidase (LOx) with an EDC/S–NHS coupling agent. The LOx-PAA:PEDOT-PB transducer was developed for lactate biosensing. The transducer provided high LOx-enzyme affinity (KMapp = 1.47 ± 0.05 mM), and a rapid response time (10 s) for lactate detection across a concentration range of 5.0 μM to 4.0 mM, showing a sensitivity of 223 ± 3 μA mM−1 cm−1 and an LOD of 1.45 μM. The LOx-PAA:PEDOT-PB transducer was integrated with a flexible screen-printed electrode, incorporating a wireless, battery-free near-field communication potentiostat module to measure lactate in artificial sweat on a skin model via smartphone. The PAA:PEDOT-PB transducer could enable connections with multiple bio-recognition molecules through polycarboxylic acid groups, providing potential avenues for the development of advanced biosensors.

Tailoring the electrochemical performance of novel BaS and their N-rGO composites for developing next-generation pseudocapacitor electrodes

The exploration of prospective versatile materials with desired morphology for energy storage applications has been reckoned to be a foremost challenge for researchers of the era. In this study, the metal sulfides and their composite with N-rGO are synthesized by facile hydrothermal approach. X-ray diffraction (XRD) pattern of the sample having cubic phase confirms its high crystallinity and purity. Photoelectron Spectroscopy (XPS) depicts utterly the constituent elements and states. Scanning electron microscope (SEM) and Transmission electron microscope (TEM) portray porous-type morphology with a high surface area.I-V measurements ensure the high conductivity of these composites whereas Fourier Transform Infrared Spectroscopy (FTIR) displays the presence of the vibrational bonds. Zeta potential of BaS is determined to be moderately negative, suggesting the existence of negatively charged entities on its surface. Brunauer-Emmett-Teller (BET) corroborates that N-rGO based composite contains a mesoporous structure with an average pore size (2.01 nm) elongated the large surface area (82.21 m2/g). The thermal stability of the composite is envisioned via Thermal gravimetric analysis (TGA). So far as the electrochemical analysis, CV results are much enough to affirm the pseudocapacitive nature of all the fabricated electrodes. An impressive cyclic stability, retaining 98.1 % of its initial capacitance over 10000th cycles is determined through N-rGO based electrode. GCD test unveils exceptional Cs of 913.34 F/g at 1 A/g with Energy density (Ed) 62.106 Wh/kg and Power density (Pd) 2896.47 W/kg and EIS provides valuable insights, showing a small semi-circle in the Nyquist plot, which indicates low charge transfer resistance. The results from the two-electrode experiment indicate that BaS/N-rGO has a specific capacitance (Cs) of 533.96 F/g at 1 A/g. Finally, our symmetrical solid-state supercapacitors exhibit exceptional capacitive performance to power LED. These results confidently indicate that the incorporation of N-rGO with metal sulfides presents promising prospects for the next-generation supercapacitor electrodes to excel the energy storage technological applications.

Elevating Oxygen Evolution using Iron Phthalocyanine Infused Vanillic acid Electrocatalyst.

Oxygen evolution reaction (OER) is the bottle neck step in water splitting reaction towards the realization of hydrogen based clean energy production and storage. Metal air batteries and polymer electrolyte membrane fuel cells (PEMFC) are the alternative green energy systems that utilise O2 and H2 in the production of continuous and high energy output without the utilization of carbon based fuels which are the major sources of pollution. Transition metal based N4 organics are explored extensively as oxygen electrocatalysts i. e., OER and oxygen reduction reaction (ORR) catalysts because of their ease of synthesis, tuneable properties, low cost and high performance with long term stability. Here, vanillic acid functionalized iron phthalocyanine (FeVAPc) was synthesised and characterised by various spectroscopic techniques. The novel FeVAPc exhibited good thermal stability and was coated on Ni foam for OER studies. The scanning electron microscopy images showed net-work like surface morphology and the X-ray photoelectron spectroscopy indicated the presence of Fe in +3 oxidation state. The Ni/FeVAPc demonstrated excellent electrocatalytic activity for OER with overpotential of 312 mV at 10 mA.cm-2 current density in 1.0 M KOH electrolyte. The designed organic based catalyst exhibited lesser Tafel slope value which is nearer to the benchmark catalyst, IrO2. The proposed catalyst exhibited good stability as phthalocyanines are highly stable and do not undergo decomposition even in strong acidic and basic corrosive media. Integration of FeVAPc onto the Ni foam resulted in higher mass activity, lower charge transfer resistance, high active surface area leading to enhanced conductivity and activity. The fabricated Ni/FeVAPc is an appropriate cost-effective, efficient and stable catalyst for OER towards industrial applications.

Corrosion behavior of predominant Halodesulfovibrio in a marine SRB consortium and its mitigation using ZnO nanoparticles

Formation of Sulfate Reducing Bacteria (SRB) biofilm accelerates microbiologically influenced corrosion (MIC). The aim of this study was to investigate both the corrosivity of a marine SRB consortium on carbon steel coupons and its mitigation in the presence of ZnO. Metagenomics analysis revealed that Halodesulfovibrio (78.9%) was predominant and could be related to MIC. The analysis also showed a remarkable shift from a highly corrosive SRB consortium in the control bioreactors to a far less corrosive consortium when ZnO was added to the bioreactors. Further results indicated that the corrosion rate of the SRB consortium was 8.17 mpy on the carbon steel coupons. In the ZnO-treated bioreactors, the count of SRB and MIC in the carbon steel coupons simultaneously reduced. Moreover, Confocal Laser Scanning Microscopy and profilometry analysis determined that ZnO could significantly decrease the amount of biofilm and the corrosion rate. Electrochemical experiments revealed higher corrosion current density (icorr) and lower charge transfer resistance (Rct) in the control bioreactors relative to the ZnO-treated bioreactors. We introduce Halodesulfovibrio as a potentially important corrosive genus in a marine SRB consortium. Additionally, ZnO could be considered a proper candidate to control the corrosion induced by Halodesulfovibrio.

Enhance electrochemical sensing of ascorbic acid and dopamine using V-CuO/GO nanocomposite

The electrochemical detection of Ascorbic acid and dopamine is crucial due to their vital roles in biological processes. Both biomolecules coexist in the human body and have the same oxidation potential, leading to electrode fouling and overlapping of oxidation potential. Accurate detection enables monitoring their levels in biological samples, aiding in disease diagnosis and treatment. This study presents the fast and green synthesis of a highly sensitive and selective electrochemical biosensor for the simultaneous detection of dopamine and ascorbic acid. The change in spherical cluster morphology into nanorods enhances the electrode's electroactive surface area, enhancing sensor sensitivity and selectivity. Electrochemical characterization techniques, including cyclic voltammetry and electrochemical impedance spectroscopy, demonstrated excellent electron transportation and low charge transfer resistance. The sensor exhibited simultaneous detection with a low limit of detection of 8 µM for dopamine and 6.9 µM for ascorbic acid, with a wide linear working range. Additionally, the sensor showed excellent selectivity and repeatability with a vast potential gap at simultaneous detection, making it suitable for clinical and food industry applications.

A flexible solid-state asymmetric supercapacitor device comprising cobalt hydroxide and biomass-derived porous carbon.

Development in the field of alternative and renewable energy sources is becoming necessary considering the current energy demands of the growing technologies. The main challenge associated with the produced energy is to store it for future use, such that it can be used when needed. Supercapacitors are among the electrochemical energy storage systems that provides higher power density, faster charging-discharging, high specific capacitance (C S), and long cycling life. Herein, the fabrication of a flexible solid-state asymmetric supercapacitor (ASC) device is reported, where Co(OH)2 hollow spheres and biomass-derived porous carbon (PC) are the cathode and anode, respectively. Co(OH)2 is a highly redox active material, whereas PC is an electric double-layer capacitive (EDLC) material. In this device, aqueous KOH solution (electrolyte) encapsulated in PVA gel (separator) was used to bind the electrodes. This Co(OH)2//PC ASC device exhibited a high C S of 260 F g-1 (at 2 A g-1). It retained ∼91% of the initial C S value (at 6 A g-1) till ∼5000 cycles. Electrochemical impedance spectroscopy (EIS) study confirmed low internal resistance (0.95 Ω) and charge transfer resistance (1.41 Ω) values of Co(OH)2//PC. These results indicate that the high electron transfer process in the electrode-electrolyte interface during the electrochemical reaction, which is responsible for the excellent performance of this ASC device. The high-performance Co(OH)2//PC ASC device exhibited an energy density of 76.7 W h kg-1 at a power density of 1416.9 W kg-1. To demonstrate its practical use, LED lights were illuminated using this Co(OH)2//PC ASC device.

Combined experimental and density functional theory approaches to address different mechanisms of nitrogen and sulfur doping on the enhancement of capacitive performance of hierarchical porous biochars

Activated carbon derived from biomass as hierarchical porous biochars (HPB) has been developed as electrode materials for supercapacitors. Nitrogen is known as the doping element that enhances quantum capacitance, but the mechanisms of sulfur doping on the quantum capacitance enhancement remain ambiguous. In this study, conventional approaches to assess the characteristics and capacitive performance of biochars were combined with density functional theory (DFT) calculations to assess different mechanisms of nitrogen and sulfur doping. The Bbiochar samples were prepared from the pyrolyzed fish bone powder at 800 °C without additional doping possessed a specific capacitance of 240 F g−1 at 1 A/g within 1 M H2SO4. Interestingly, additional nitrogen doping through urea mixing and additional sulfur doping through thiosulfate mixing prior to the pyrolysis enhanced the specific capacitance of biochar samples to exceed 400 F g−1 under the same condition. The urea mixed sample possessed low porosity but high charge transfer resistance, while the thiosulfate mixed sample possessed high porosity but low charge transfer resistance. The different underlying mechanisms were discussed through DFT calculations on graphene models designed based on the x-ray photoelectron spectroscopy (XPS) results. Nitrogen-doped configurations with topological defects mainly stored charge at the dangling atoms and possessed a relatively high quantum capacitance. Meanwhile, doped configurations of oxidized sulfur groups required relatively low formation energy and possessed large bond dipoles, corresponding to larger pore size and surface area of the thiosulfate mixed biochars. Understanding the contrary between effects of nitrogen and sulfur doping could resolve the bottleneck on enhancing the performance of electronic double layer supercapacitors.

Multiphasic titania photoanode: A facile phase assisted approach to enhance the photoelectrochemical and photovoltaic performance

A facile low-temperature method has been proposed and utilized to synthesize pristine and multiphasic titania. Increasing reactant acid content led to the phase transition of titania from pristine anatase to triphasic anatase-rutile-brookite mixed phase; then to biphasic anatase-rutile mixed phase and ultimately pristine rutile. Morphological differences between the samples led to different dye loading on the Dye Sensitized Solar Cell (DSSC) photoanodes, with anatase showing highest loading. However, the Electrochemical Impedance Spectroscopic (EIS) analyses revealed that the triphasic titania photoanode showed superior charge transport ability as evidenced by the lowest charge transfer resistance and highest carrier lifetime. This led to the triphasic DSSC showing a photoconversion efficiency of 4.23 % which is 45 % greater than the reference DP25 DSSC and 72 % better than that of the anatase DSSC despite having a 24 % lower dye loading. These factors suggest that the charge transport properties precede the dye loading capability of the photoanode in determining the DSSC performance. The intimate ternary interfacial junction between the anatase, rutile and brookite phases may be responsible for the enhanced charge transport properties of the triphasic titania. Thus, it is essential to ensure superior photoanode charge transport characteristics to enhance the DSSC performance.