Lateral Size Research Articles

Comparative study of sodium and potassium compounds as promoters for growth of monolayer MoS2 with high crystal quality on SiO2/Si substrate

Monolayer MoS2 is promising candidate for fabrication of optoelectronic devices due to its direct bandgap nature and high carrier mobility. Alkali metal compounds have been demonstrated to be helpful promoters for the growth of large single crystal monolayer MoS2 on SiO2/Si substrate. However, the catalytic mechanism of alkali metal compounds is still under debate. Herein, we compared the surface morphology, optical properties, and electrical properties of monolayer MoS2 flakes grown on SiO2/Si substrate assisted by promoters containing potassium or sodium cations and halogen (chlorine) or non-halogen (hydroxide) anions, i.e. NaCl, NaOH, KCl and KOH. Based on the analysis of existing growth mechanism, we proposed that the alkali metal cation, plays a dominant role in promoting the lateral growth of monolayer MoS2 and obtaining high crystal quality. Furthermore, potassium has a greater promoting effect than sodium. By optimizing growth conditions, monolayer triangular MoS2 flakes with large lateral size over 160 μm were grown assisted by KCl promoter. Raman and PL spectra verified excellent crystal quality of the flakes, with typical electron mobilities of 2.98 and 20 cm2 V−1 s−1 for the back-gated filed effect transistors fabricated on as-grown and fresh SiO2/Si substrates, respectively.

Upscaling Brønsted acid intercalation and exfoliation of graphite into graphene by polyoxometalate clusters for sodium-ion battery application

Non-oxidative intercalation of graphite avoids damage to graphene lattices and is a suitable method to produce high-quality graphene. However, the yield of exfoliated graphene is low in this process due to the poor delamination efficiency of guest species. In this study, a Brønsted acid intercalation protocol is developed involving polyoxometalate (POM) clusters (H6P2W18O62) as guests and intercalation of graphite is realized at the sub-nanometer scale. Theoretical simulation based on DFT elucidates the stepwise intercalation mechanism of Brønsted acid molecules and clusters. Unlike common molecules/ionic guests, intercalation of POM clusters induces large expansion and extensive donor–acceptor interactions among graphite interlayers. This significantly weakens the van der Waals forces and promotes exfoliation efficiency of graphene layers. The exfoliated graphene possesses outstanding features of large lateral size, thin thickness, and high purity, and shows excellent performance as the anode for high power sodium-ion batteries. This work proffers a new pathway toward non-oxidative intercalation of graphite for large-scale production of graphene.

Method for fabricating a mesh ripple filter for charged-particle therapy

Objective. A simple, low-cost ripple filter consisting of multiple mesh sheets (mRiFi) was previously developed to reproducibly widen the Bragg peak of heavy-ion beams. To fabricate the mRiFi, the mRiFi parameters such as the wire material, wire diameter, wire spacing, and number of mesh sheets had to be determined. However, it was unclear how these parameters contribute to shifting and widening of the Bragg peak as well as to lateral spreading of the beam passing through the mRiFi. The purposes of this study were to clarify the contributions and to propose a recipe for fabricating a mRiFi with the desired performance values. Approach. We established an analytical calculation method to estimate shifting and widening of the Bragg peak and lateral spreading of heavy-ion beams passing through the mRiFi for given mRiFi parameter values. We also performed Monte Carlo simulations to validate the analytical calculation method. The recipe for fabricating the mRiFi with desired performances was established based on the analytical calculation method. Using the recipe, we fabricated the mRiFi for multi-ion therapy and evaluated its performance through demonstration experiments with helium-, carbon-, oxygen-, and neon-ion beams. Main results. The difference between the results of the Monte Carlo simulation and the analytical calculation was less than 0.4 mm for the peak shift, 0.15 mm for the peak width, and less than 0.11 mm for the lateral beam size which validated the analytical calculation method. The experimentally observed shift and width of the Bragg peak were consistent with the analytical calculations. Significance. We proposed a method to determine mRiFi parameters for fabricating a mRiFi with a desired performance, i.e. adequate widening of the Bragg peak with an acceptable peak shift and lateral beam spread. The proposed method allows anyone to fabricate a simple and low-cost mRiFi satisfying desired specifications.

Scanning‐Laser‐Based Microstereolithography of Microfluidic Chips with Micron Resolution

AbstractThe constant improvement of stereolithography (SL) in terms of achievable resolution and printing time has sparked high expectations that SL will enable the rapid prototyping of truly microfluidic chips with features below 100 µm. However, most commercial high‐resolution stereolithography devices are based on Digital Light Processing (DLP) and thus sacrifice lateral printing size for resolution. Consequently, even 10 years after the advent of microstereolithography there is no commercialized 3D printing system that can effectively fulfill all the demands to replace soft lithography for microfluidic prototyping. In this work, for the first time, This study demonstrates that a commercial laser‐based stereolithography device is capable of manufacturing microfluidic chips with embedded channels smaller than 100 µm with a footprint of 7.24 × 0.3 cm2. A chip fabricated in poly(ethylene glycol) diacrylate (PEGDA) that can readily be used for fluid mixing, is presented in this study. This research shows that the accessibility of high‐resolution chips with footprints of several cm2, using laser‐based stereolithography, enables the manufacturing of truly microfluidic systems with high impact on prototyping and manufacturing.

Unexpected Self-Assembly of Nanographene Oxide Membranes upon Electron Beam Irradiation for Ultrafast Ion Sieving.

Nanographene oxide (nGO) flakes-graphene oxide with a lateral size of ≈100nm or less-hold great promise for superior flux and energy-efficient nanofiltration membranes for desalination and precise ionic sieving owing to their unique high-density water channels with less tortuousness. However, their potential usage is currently limited by several challenges, including the tricky self-assembly of nano-sized flakes on substrates with micron-sized pores, severe swelling in aqueous solutions, and mechanical instability. Herein, the successful fabrication of a robust membrane stacked with nGO flakes on a substrate with a pore size of 0.22µm by vacuum filtration is reported. This membrane achieved an unprecedented water permeance above 819.1 LMH bar-1, with a high rejection rate of 99.7% for multivalent metal ions. The nGO flakes prepared using an electron beam irradiation method, have uniquely pure hydroxyl groups and abundant aromatic regions. The calculations revealed the strong hydrogen bonds between two nGO flakes, which arise from hydroxyl groups, coupled with hydrophobic aromatic regions, greatly enhance the stability of stacked flakes in aqueous solutions and increase their effective lateral size. The research presents a simple yet effective approach toward the fabrication of advanced 2D nanographene membranes with superior performance for ion sieving applications.

Effective method for photonic jet shaping in reflection mode.

We report an effective method to shape a photonic jet (PJ) generated by a dielectric cuboid scatterer on a hollow reflection screen. The study focuses on the shaping of PJ by hollow and cuboid geometries, including side length, depth, and position. The results show that all the geometric parameters can effectively shape the PJ in characteristic parameters of intensity, focal length (FL), and lateral size. The comparison shows that the present shaping method is much superior to the previously reported one based on a change of cuboid height, characterized by three times larger of the varying ranges of the PJ characteristic parameters. The shaping by the side length and depth of hollow and cuboid is explained from viewpoints of ray optics and electromagnetic field theory in terms of hollow-induced phase singularity in Poynting vector distribution. The hollow position mainly shapes the propagation trajectory of PJ. The deviation of the hollow position results in the curvature of the propagation trajectory of PJ, and the curvature is correlated with the asymmetric extent of the scattering system.

Microwave-Assisted Efficient Intercalation for Fast Fabrication of High-Quality and Large-Size Single-Layer Ti3C2Tx Nanosheets.

A novel microwave-assisted intercalation (MAI) strategy is proposed for fast and efficient intercalation of layered MXene to prepare large-size single-layer MXene. After LiF-HCl etching of Ti3AlC2, the as-prepared multi-layer Ti3C2Tx (M-T) are intercalated with Li3AlF6 as an intercalator and ethylene glycol (EG) as a solvent under microwave irradiation for 5min. Furthermore, the dispersed high-quality large-sized single-layer Ti3C2Tx (S-T) nanosheets with a thickness of 1.66nm and a large lateral size over 20µm are achieved with a yield of over 60% after a further ultrasonic delamination followed by electrostatic precipitation, acid washing, and calcination. In addition, Pd/S-T composite catalyst, which is constructed with Pd nanoparticles supported on the as-prepared S-T nanosheets, exhibits an excellent performance for rapid and efficient selective hydrogenation of nitroarenes with H2 under a mild condition. At room temperature, full conversion of nitrobenzene and 100% aniline selectivity are achieved over Pd/S-T catalyst in 20min with 0.5MPa of H2 pressure. This work provides a novel method for facile, fast, and large-scale preparation of single-layer MXene and develops a new approach for constructing efficient nanocatalytic systems.

Study on the preparation and mechanism of two-dimensional nanomaterials as plugging agents for oil-based drilling fluids

During the drilling of shale formations using oil-based drilling fluids (OBDFs), the infiltration of filtrate into formation micro-fractures is one of the primary causes of wellbore instability. Wellbore instability not only increases non-productive time during the drilling process but also significantly raises development costs. The key to addressing this issue is the development of nano plugging agents capable of effectively sealing formation micro-cracks. However, existing nano plugging agents suffer from poor dispersibility and mismatch with the scale of rock fractures under formation conditions. In this study, two-dimensional nano graphene oxide was synthesized via a redox method. XRD and Raman analyses confirmed the production of high-quality, few-layer two-dimensional graphene sheets. TEM analysis revealed that the synthesized high-reduction graphene oxide (R-GO) had an average lateral size of 2.16 μm, making it suitable for sealing formation micro-cracks. Performance tests demonstrated that R-GO maintained its non-aggregating and highly dispersible properties under formation conditions. Additionally, permeability reduction experiments showed that adding 0.25 %, 0.50 %, and 0.75 % R-GO resulted in permeability reduction rates of 29.12 %, 31.86 %, and 49.16 %, respectively. The conclusion is that R-GO, as a nano plugging agent for OBDFs, can form a dense sealing layer on the surfaces of shale nano-micro pores and fractures, thereby enhancing the stability of shale formations.

Controlled Synthesis of Terbium-Doped Colloidal Gd2O2S Nanoplatelets Enables High-Performance X-ray Scintillators.

Terbium-doped gadolinium oxysulfide (Gd2O2S:Tb3+), commonly referred to as Gadox, is a widely used scintillator material due to its exceptional X-ray attenuation efficiency and high light yield. However, Gadox-based scintillators suffer from low X-ray spatial resolution due to their large particle size, which causes significant light scattering. To address this limitation, we report the synthesis of terbium-doped colloidal Gadox nanoplatelets (NPLs) with near-unity photoluminescence quantum yield (PLQY) and high radioluminescence light yield (LY). In particular, our investigation reveals a strong correlation between PLQY, LY, particle size, and Tb3+concentration. Our synthetic approach allows precise control over the lateral size and thickness of the Gadox NPLs, resulting in a LY of 50,000 photons/MeV. Flexible scintillating screens fabricated with the solution-processable Gadox NPLs exhibited a 20 lp/mm X-ray spatial resolution, surpassing commercial Gadox scintillators. These high-performance and flexible Gadox NPL-based scintillators enable enhanced X-ray imaging capabilities in medicine and security. Our work provides a framework for designing nanomaterial scintillators with superior spatial resolution and efficiency through precise control of dimensions and dopant concentration.

Soliton groups and extreme wave occurrence in simulated directional sea waves

The evolution of nonlinear wave groups that can be associated with long-lived soliton-type structures is analyzed, based on the data of numerical simulation of irregular deep-water gravity waves with spectra typical to the ocean and different directional spreading. A procedure of the windowed Inverse Scattering Transform, which reveals wave sequences related to envelope solitons of the nonlinear Schrödinger equation, is proposed and applied to the simulated two-dimensional surfaces. The soliton content of waves with different directional spreading is studied in order to estimate its dynamical role, including characteristic lifetimes. Statistical features of the solitonic part of the water surface are analyzed and compared with the wave field on average. It is shown that intense wave patterns that persist for tens of wave periods can emerge in stochastic fields of relatively long-crested waves. They correspond to regions of locally enhanced on average waves with reduced kurtosis. This eventually leads to realization of locally extreme wave conditions compared to the general background. Although intense soliton-like groups may be detected in short-crested irregular waves as well, they possess much shorter lateral sizes, quickly disperse, and do not influence the local statistical wave properties.

The ephemeral state of ice in micro cold traps on the Moon

Micro cold traps stand out as promising targets for future investigation missions to the lunar polar regions, due to their greater accessibility compared to macro cold traps. However, this advantage naturally comes at the cost of their size, which limits the amount of ice they can potentially harbor. Here, we investigate the permanently shadowed volume (PSV) of micro cold traps — an upper limit for their potential ice capacity. We find that, as expected, the PSV depth increases with latitude and surface roughness, but is on average much shallower (∼0.5−1%) compared to the topographic baseline. By comparing the expected destruction and accumulation rates of ice to the potential maximum capacity of micro cold traps, we predict their infill as a function of lateral size, and the lifetime of the ice they harbor. Our results could be used by future investigation missions to the lunar polar regions to constrain the delivery rate and delivery mechanism of ice to the Moon.

Tuning Surface Adhesion Using Grayscale Electron-beam Lithography.

Surface texturing of manufactured products tailors their properties, such as friction, adhesion, biocompatibility, or fluid interactions. However, advancements in this area are largely the result of trial-and-effort testing and generally lack a science-guided framework for determining the surface topography that will optimize performance. The present investigation explores grayscale electron-beam lithography as a means to create multiscale surface patterns to control surface performance. Here, we created and characterized a set of surface textures on a silicon wafer; the textures were superpositions of sine waves of varying wavelengths and amplitudes. First, the multiscale topography of the patterned surface was characterized, using profilometry and atomic force microscopy, to understand its fidelity to the designed-in pattern. The results of this analysis demonstrated how grayscale lithography accurately controlled the lateral size of features but was less precise on the vertical height of the surface, and also introduced inherent roughness below the scale of patterning. Second, a micromechanical tester was used to characterize the adhesion of the surfaces with large-scale polished silicon spheres. The results showed that adhesion could be tailored, with significant contribution from all of the designed-in length scales of topography. The strength of adhesion did not correlate with conventional roughness parameters but could be accurately modeled using simple numerical integration. Taken together, this investigation demonstrates the promise and challenges of grayscale e-beam lithography with multiscale patterns as a method for the tailoring of surface performance.

Fast growth of large-sized organic single crystals via spin coating

Spin-coating stands out as one of the fastest and simplest processes for material solidification. While it is commonly employed for producing polycrystalline thin films, recent endeavors have explored its potential for epitaxial growth, albeit primarily limited to inorganic materials. In this study, we demonstrate the spin-coating method enabling the rapid growth of large-sized organic single crystals (OSCs). Within 2 h, we successfully obtained OSCs with controlled lateral sizes of up to 2 mm, which conventionally takes several weeks using slow solvent evaporation. Raman mapping and UV–Vis absorption measurements confirmed the growths of the OSCs. We propose the growth mechanism by using the supersaturated dynamic fluid model. Furthermore, we demonstrate the device integration of these OSCs for charge-transfer complex channel, revealing ambipolar behavior during gate sweep. This innovative OSCs production method has the potential to advance the various field of science and electronics, traditionally hindered by the scarcity of adequately sized OSCs.

Boundary effect on the soil strength estimation from T-bar penetration tests

The T-bar penetration tests have gained widespread use in assessing the undrained shear strength of marine clays. However, when dealing with model tests or sampled soil with a small diameter of the tube, the reliability of T-bar test results is influenced by both the boundary effect and the soil flow mechanism around the T-bar. In this paper, a comprehensive investigation into the boundary effect on T-bar penetration resistance was conducted by using the large deformation finite element (LDFE) method in conjunction with laboratory tests. The study reveals that the boundary conditions significantly impact the T-bar resistance when the lateral boundary dimension is smaller than 12D. Specifically, the T-bar penetration resistance is underestimated for smooth boundaries and overestimated for rough boundaries. For soils with higher strength, a larger boundary size is required. The bottom boundary also affects the T-bar resistance until the full-flow mechanism is established. However, once the full-flow mechanism is achieved, the boundary effect on T-bar penetration resistance diminishes, even for small lateral boundary sizes (2D). Considering the fact that it is challenging to attain the full-flow mechanism, especially for higher strength soils, a simple algorithm is proposed to estimate soil strength based on a shallow penetration depth (2D). This algorithm is validated through laboratory tests. To address the difficulty in achieving the full-flow mechanism, by applying the overburden pressure during the T-bar test, a novel T-bar test method is suggested. This innovative approach promises to resolve the issue effectively.

Fiber Optic Sensor Coated with Multiple Layers of Hexagonal Boron Nitride Nanosheets (BNNS) for the Detection of Volatile Organic Compounds.

Nowadays, volatile organic compound (VOC) detection is imperative to ensure environmental safety in industry and indoor environments, as well as to monitor human health in medical diagnosis. Gas sensors with the best sensor response, selectivity, and stability are in high demand. Simultaneously, the advancement of nanotechnology facilitates novel nanomaterial-based gas sensors with superior sensor characteristics and low power consumption. Recently, boron nitride, a 2D material, has emerged as an excellent candidate for gas sensing and demonstrated exceptional sensing characteristics for new-generation gas sensing devices. Herein, ultrathin porous boron nitride nanosheets (BNNSs) with large lateral sizes were synthesized using a facile synthesis approach, and their material characteristics were investigated utilizing a variety of analytical techniques, including X-ray diffraction, Fourier transform infrared spectroscopy, ultraviolet spectroscopy, X-ray photoelectron spectroscopy, and scanning electron microscopy. A BNNS-coated cladding-modified fiber optic sensor (FOS) probe was prepared and employed for VOC (ammonia, ethanol, and acetone) sensing across concentrations varying from 0 to 300 ppm. The BNNSs-coated FOS demonstrated better selectivity toward 300 ppm ammonia, and specifically annealed BNNSs displayed a maximum sensor response of 55% along with a response/recovery times of 15 s/34 s compared to its counterparts. The superior ammonia sensing performances could be attributed to the formation of ultrathin nanosheets and a porous surface with slit-like features in hexagonal boron nitride.

Switching-on Delay Jitter Caused by Lateral Distribution of Current Channel of Avalanche Transistor

The stability of the avalanche transistor’s (AT’s) switching-on process is essential for its extensive application in power semiconductors. The switching-on process was typically described in one-dimensional terms, overlooking the effects of multi-dimensional structural variations on stability. This paper investigated the influence of the lateral distribution of current channels on the switching-on delay jitter in the AT. The lateral size of the current channel affects the transit time by changing the electron path in the base region, resulting in the switching-on delay jitter of the AT. An analytical formula for the lateral size of the current channel and the switching-on delay jitter has been proposed. The two-dimensional simulation model of the AT gave the distribution of current channels. The model’s accuracy was verified by comparing experimental and simulation data. The experimental data proved that the base transit time was the main component of the switching-on delay. The results show that the switching-on delay jitter can be significantly reduced by adjusting the current channel’s lateral size. In addition, the trigger signal’s characteristics also change the current channel’s lateral distribution and then affect the stability of the switching-on delay, which provides a new perspective for the design and application of ATs.

Observation of Mermin-Wagner behavior in LaFeO3/SrTiO3 superlattices

Two-dimensional magnetic materials can exhibit new magnetic properties due to the enhanced spin fluctuations that arise in reduced dimension. However, the suppression of the long-range magnetic order in two dimensions due to long-wavelength spin fluctuations, as suggested by the Mermin-Wagner theorem, has been questioned for finite-size laboratory samples. Here we study the magnetic properties of a dimensional crossover in superlattices composed of the antiferromagnetic LaFeO3 and SrTiO3 that, thanks to their large lateral size, allowed examination using a sensitive magnetic probe — muon spin rotation spectroscopy. We show that the iron electronic moments in superlattices with 3 and 2 monolayers of LaFeO3 exhibit a static antiferromagnetic order. In contrast, in the superlattices with single LaFeO3 monolayer, the moments do not order and fluctuate to the lowest measured temperature as expected from the Mermin-Wagner theorem. Our work shows how dimensionality can be used to tune the magnetic properties of ultrathin films.

SPI-Modified h-BN Nanosheets-Based Thermal Interface Materials for Thermal Management Applications.

The rising concern over the usage of electronic devices and the operating environment requires efficient thermal interface materials (TIMs) to take away the excess heat generated from hotspots. TIMs are crucial in dissipating undesired heat by transferring energy from the source to the heat sink. Silicone oil (SO)-based composites are the most used TIMs due to their strong bonding and oxidation resistance. However, thermal grease performance is unreliable due to aging effects, toxic chemicals, and a higher percentage of fillers. In this work, TIMs are prepared using exfoliated hexagonal boron nitride nanosheets (h-BNNS) as a nanofiller, and they were functionalized by ecofriendly natural biopolymer soy protein isolate (SPI). The exfoliated h-BNNS has an average lateral size of ∼266 nm. The functionalized h-BNNS/SPI are used as fillers in the SO matrix, and composites are prepared using solution mixing. Hydrogen bonding is present between the organic chain/oxygen in silicone polymer, and the functionalized h-BNNS are evident from the FTIR measurements. The thermal conductivity of h-BNNS/SPI/SO was measured using the modified transient plane source (MTPS) method. At room temperature, the maximum thermal conductivity is 1.162 Wm-1K-1 (833% enhancement) at 50 wt % of 3:1 ratio of h-BNNS:SPI, and the thermal resistance (TR) of the composite is 5.249 × 106 K/W which is calculated using the Foygel nonlinear model. The heat management application was demonstrated by applying TIM on a 10 W LED bulb. It was found that during heating, the 50 wt % TIM decreases the surface temperature of LED by ∼6 °C compared with the pure SO-based TIM after 10 min of ON condition. During cooling, the modified TIM reduces the surface temperature by ∼8 °C under OFF conditions within 1 min. The results indicate that natural polymers can effectively stabilize and link layered materials, enhancing the efficiency of TIMs for cooling electronics and LEDs.

Study of Morphology Control of Electro-Deposited Silver on Electro-Chemically Exfoliated Graphene Electrode and Its Conductivity.

Solution-processed graphene is beneficial for large-scale, low-cost production. However, its small lateral size, variable layer thickness, and uncontrollable oxidation level still restrict its widespread electronic application. In this study, a newly developed electrochemical exfoliation process was introduced, and a graphene-patched film electrode was fabricated by interfacial self-assembly. We were able to minimize the deterioration of graphene colloids during exfoliation by voltage and electrolyte modulation, but the patched structure of the graphene electrode still showed low conductivity with numerous inter-sheet junctions. Therefore, we determined the optimal conditions for the growth of fully networked silver structures on the multi-stacked graphene film by direct current electro-deposition, and these silver-graphene composite films showed significantly lowered graphene-colloid-patched film surface resistance.

Solvothermal Preparation of Crystal Seeds and Anisotropy-Controlled Growth of Silver Nanoplates.

We synthesized silver nanoplates using the solvothermal method and, for the first time, placed them as crystal seeds in a water-based growth solution, thereby successfully achieving the large-scale production of silver nanoplates. The synthesis method enabled independent control of the lateral size and vertical size of the silver nanoplates. More specifically, the lateral size could be adjusted within the range of 565 nm-1.682 μm, while the vertical size was achieved by introducing Cl- as a capping agent and the vertical size was thickened from 18.28 to 40.41 nm.