Increase In Friction Coefficient Research Articles

Semi-analytical solution of MHD free convective flow of a nanofluid over an exponentially stretching porous sheet in the presence of heat source/sink

In this study, the magnetohydrodynamic flow and heat transfer of electrically conducting nanofluid over an exponentially stretching porous sheet is investigated. By introducing similarity variables, the non-linear set of partial differential governing equations, are transformed into a system of ordinary nonlinear differential equations. The equations are solved semi-analytically by the Optimal Collocation Method (OCM) which is a powerful method to solve equations containing infinite boundary conditions. The accuracy of the OCM results is examined by the Richardson method. The effects of the different physical parameters such as magnetic field strength, nanofluid volume fraction, suction strength, and the heat sink/source value are discussed on the flow and heat transfer characteristics of the problem. The obtained results show that the velocity and temperature of nanofluid increase with the increase in volume fraction. Also, when suction increases, the thickness of the boundary layers decreases. As the strength of the magnetic field (Hartmann) increases, the temperature slightly increases but the flow rate of the nanofluid decreases. The skin friction coefficient and Nusselt number increase when the values of suction parameters, volume fraction, magnetic field, and the field angle increase.

Validation on fly ash DEM microparameters based on coarse-grained method

The computational efficiency of the discrete element simulation process is often a limiting factor. However, the use of the coarse-grained method, which employs dimensional analysis to amplify particles, significantly improves computational efficiency. This research utilizes the coarse-grained method to amplify particles and examines the impact of linear models on the mechanical of fly ash. By examining parameters such as magnification, stiffness, sliding friction coefficient, and rolling friction coefficient, we establish the relationship between fly ash cohesion, internal friction angle, and microscopic parameters in discrete element method (DEM) simulation. The simulation results demonstrate that the shear strength of fly ash increases as magnification, stiffness, and sliding friction coefficient increase. The rolling friction coefficient, on the other hand, has minimal effect on shear strength. The elastic potential energy of the system is unaffected by magnification, with stiffness inversely proportional to adaptable potential power. However, sliding and rolling friction coefficients positively impact adaptable potential power. Furthermore, this study proposes a practical simplification method for amplification of materials with small particle sizes. The comparison between numerical simulation and experimental data yields consistent results. As a result, this study provides a foundation for the application of large-scale fly ash transportation, storage, and other engineering purposes.

An analytical approach for predicting the fillet and contact stresses in symmetric and asymmetric spur gears under frictional mesh assumptions

A precise estimation of the bending and contact stresses, as well as the true friction value during the gear mesh, are critical aspects of a cost-effective and safe gear design. Previous studies have usually neglected friction by assuming a frictionless contact. Additionally, the impact of friction on the bending stress of spur gears has rarely been addressed. Moreover, to the authors' best knowledge, the impact of friction on the weakest section, stress concentration factor, and Lewis form factor remain unexplored for both symmetric and asymmetric gears. This study presents an analytical model incorporating friction at different contact locations to calculate the variables related to the tooth's weakest section. This model facilitates the evaluation of the stress concentration factor, Lewis form factor, and maximum tensile stress for symmetric and asymmetric gears. The proposed model is especially beneficial for assessing the load-carrying capacity of spur gears operating in challenging conditions. The results showed that the asymmetric spur gear is superior to its equivalent symmetric counterpart in terms of tooth form factor; however, this superiority decreases as the coefficient of friction increases. In addition, friction has been found to have a greater effect on fillet stress than contact stress. For μ = 0.2, at the HPSTC, the contact load and tooth form factor decreased by 7 % and 12 %, respectively, and the fillet stress worsened by 13 % compared to the frictionless assumption. Meanwhile, at the LPSTC, the stress concentration factor and contact stress increased by 9 % and 3 %, respectively.

Numerical investigation of wheel-rail rolling contact characteristics and damage in a high-speed turnout switch panel under a large ramp

The damage pattern on a railway line under large ramp is more complicated than that of a standard railway line. In order to investigate the influence of the complex wheel-rail contact evolution in the turnout area on the service characteristics of the switch panel under a large ramp, this paper establishes an explicit FE model of the wheel-rail rolling contact on a 40‰ slope. The performance of a train crossing the turnout and the change in mesoscopic contact behavior is then analyzed under different operating conditions. The distribution rule for wear and fatigue damage to the switch rail under a large ramp is studied, with a regulation strategy proposed for improving the service performance of the switch rail based on the results. These show that there is an obvious cyclical incremental phenomenon on the mechanical behavior at the front end of the switch rail, with uneven abrasion distributed throughout the region. The increase in axle weight, speed and friction coefficient increases the stress concentration of the switch rail and exacerbates the damage. As the train passes through the switch panel, the service life of the switch rail can be significantly improved by reducing the traction.

Probing the effect of displacement on electrical contact tribological behavior at the risk frequency of nuclear safety DCS equipment

Purpose This paper aims to study the tribological characteristics of the electrical contact system under different displacement amplitudes. Design/methodology/approach First, the risk frequency of real nuclear safety distributed control system (DCS) equipment is evaluated. Subsequently, a reciprocating friction test device which is characterized by a ball-on-flat configuration is established, and a series of current-carrying tribological tests are carried out at this risk frequency. Findings At risk frequency and larger displacement amplitude, the friction coefficient visibly rises. The reliability of the electrical contact system declines as amplitude increases. The wear morphology analysis shows that the wear rate increases significantly and the degree of interface wear intensifies at a larger amplitude. The wear area occupied by the third body layer increases sharply, and the appearance of plateaus on the surface leads to the increase of friction coefficient and contact resistance. EDS analysis suggests that oxygen elements progressively arise in the third layer as a result of increased air exposure brought on by larger displacement amplitude. Originality/value Results are significant for recognizing the tribological properties of electrical connectors in nuclear power control systems. Peer review The peer review history for this article is available at: https://publons.com/publon/10.1108/ILT-03-2024-0098/

Newtonian Heating in Magnetohydrodynamic (MHD) Hybrid Nanofluid Flow Near the Stagnation Point over Nonlinear Stretching and Shrinking Sheet

Hybrid nanofluids have demonstrated superior heat transfer performance in numerous applications. However, there remains a need for further research to broaden the scope of their potential applications. The unique behavior of hybrid nanofluids, driven by their potential for improved thermal efficiency, continues to be a focal point of investigation and exploration. This study focuses on the effects of Newtonian heating in MHD hybrid nanofluid near the stagnation point over a nonlinear stretching/shrinking sheet. The Tiwari and Das model, which is a single-phase model, was used to develop the mathematical model. The base fluid and the nanoparticles are assumed to be in thermal equilibrium; hence there is no thermal slip between them. The combination of metal (Cu) and metal oxide (Al2O3) nanoparticles with water (H2O) as the base fluid is used for the analysis. Furthermore, the governing equations are transformed using a similarity transformation technique into similarity equations, which are then solved numerically using a bvp4c function in MATLAB software. Numerical comparison with the published literature is conducted to validate the numerical results, and excellent agreement is found. The impact of physical parameters on the velocity, temperature, skin friction, and local Nusselt number is graphically deliberated. The outcomes suggest that non-unique solutions are found in a specific range of the shrinking parameter. It is also observed that increasing Cu (copper) nanoparticle volume fractions cause an increase in the skin friction coefficient and the local Nusselt number. The presence of magnetic and nonlinear parameters widens the range of solutions to exist while different observation is noticed with an increase in the volume fraction of Cu. Other than that, it has been shown that the Nusselt number increases as the magnetic parameter increases. Lastly, the rise of Newtonian heating contributes to an increase in the temperature profile. This investigation is crucial for understanding the thermal behavior of Cu-Al2O3/ H2O under the influence of physical factors like a magnetic field and Newtonian heating.

Tribological behavior evaluation of poly-ether-ether-ketone (PEEK) in dry journal bearing on shaft wear test

This paper investigated the tribological behavior of pure PEEK playing as a dry journal bearing, sliding against stainless steel, under real-life operating conditions in a wear test lasting 2 h. Four conditions were carried out with different magnitudes of normal load and sliding speed, while keeping a constant PV parameter. Sample topography assessments were performed with scanning electron microscopy and white light interferometry techniques. In addition, PEEK samples were also evaluated by Fourier Transformed Infrared Spectroscopy and thermal analyses by Differential Scanning Calorimetry. The coefficient of friction (COF) changed throughout the wear test and exhibited a running-in period followed by a transition, with an increase of COF, and then a tendency to reach a steady-state. Moreover, the COF behavior obtained suggests that there was an influence of the wear test parameters, mainly right after the running-in period — and the COF averages for the steady-state period were statistically equal. Stainless steel samples showed mild wear, while PEEK samples had a drastic alteration of their topography imposed by the wear test — including an increase in its degree of crystallinity. Nonetheless, the PEEK journal bearing samples did not fail from wear and their mass losses were small. Polymeric wear particles were generated and were found weakly adhered to both the body and the counter body. PEEK exhibited a lumpy transfer process — nonetheless, SEM images evaluation was useful to verify that these particles were eventually merged during sliding, and kneaded in the convex-concave contact, which provided them a film-like appearance. Furthermore, adhesive and abrasive wear mechanisms were identified, which were shown to be related to the journal bearing on shaft wear test arrangement.

Surface effect on the partial-slip contact of a nano-sized flat indenter

The partial-slip contact at nano-scale is always influenced by a surface effect. A new model based on the Gurtin-Murdoch (G-M) surface elasticity theory is proposed in this paper to study the partial-slip contact behavior of a rigid flat nano-indenter on an elastic half-space. The surface effect in the partial-slip contact is characterized via a non-classical boundary condition involving a surface-induced normal traction related to the residual surface stress and a surface-induced tangential traction related to the surface elasticity, the influences of which on stress and displacement fields and the stick-slip state at the contact surface are investigated. It is found that, with the increase of residual surface stress, both the normal pressure and vertical and horizontal displacements in the contact zone decrease, the relative slip between indenter and substrate reduces and the stick region is enlarged. Such effects are basically attributed to the action of the surface-induced normal traction opposite to the externally applied compression. However, the increase of surface elastic constants is conductive to the relative slip and results in a shrinkage of the stick region, which is attributed to the action of the surface-induced tangential traction opposite to the frictional stress. An interesting phenomenon is further unveiled that, when the frictional coefficient increases, the dominant role in affecting the stick-slip state changes from the surface-induced tangential traction to the normal one, thus inspiring a feasible route to manipulate the surface effect by tuning the frictional coefficient of substrate. The present research enables one to better understand the partial-slip contact behavior of nano-indenters, which is of guiding value for anti-wear designs in nano-mechanical devices.

Analytical Investigation of Magnetohydrodynamic Hybrid Nanofluid Flow Over a Permeable Shrinking Sheet

The flow and heat transfer of Cu-Al2O3/water hybrid nanofluid over a shrinking sheet were investigated taking account of the magnetic field, suction, variable heat sink, and thermal radiation. At first, the governing equations were completely changed into ordinary differential equations (ODEs) with proper transformations. The novelty of this investigation is that the ODEs were analytically solved and the dual characteristics of flow properties and heat transfer were graphically presented. Results revealed that an increase in the volume fraction of Cu nanoparticles (φ2), magnetic parameter (M), and suction parameter (S) caused an increase in the local skin friction coefficient (Rex1/2Cf), local Nusselt number (Rex-1/2Nux) and region of the existence of dual solutions. With the increase of φ2, M, and S, fluid velocity increased and temperature decreased. Contrary to this, the converse was observed for increasing the volume fraction of Al2O3 nanoparticles (φ1). These findings indicated that with proper tuning of these parameters, the cooling rate of a shrinking sheet could be controlled and the possible working conditions of a system might be increased.

Mechanically mixing and oxidation layer induced by different contact surface of columnar Cu under dry sliding condition

The dry sliding behavior of columnar Cu with vertical orientation (VO) and horizontal orientation (HO) coupling with 1045 steel was studied. The results show that when the sliding distance is 672 m, the friction coefficient of HO Cu is 0.21 lower than that of VO Cu, and the wear rate is reduced by 0.63·10−6 g·N−1m−1; when the sliding distance is 1344 m, the friction coefficient of HO Cu is 0.10 lower than that of VO Cu, and the wear rate is reduced by 0.31·10−6 g·N−1m−1. The Fe3O4 oxide was detected on the wear surface of HO Cu by Raman spectroscopy. And it plays a greater role in lubrication and protection of friction layer. On the worn surface of VO Cu, there is obvious softening caused by thermal activation or composition mixing. This softening will lead to a significant decrease in the strength of the friction layer, and the friction coefficient and wear loss increase negatively.

Simulation of fretting wear in steel wires under variable coefficient of friction and variable wear coefficient

In this paper, the fretting wear behaviour of steel wires working in coal mining technology is studied numerically. In past studies, the fretting process of steel wires was carried out numerically considering that the coefficient of friction (COF) and wear coefficient (WC) are constant parameters. However, it has been noticed experimentally that COF increases up to a certain number of fretting cycles and then becomes constant, i.e. a steady-state stage, depending on the loading conditions. This increase in COF during the fretting process is also known as the running-up stage. The fretting wear model is modified to evaluate the influence of the varying coefficient of friction (VCOF), which is associated with the variable wear coefficient (VWC), so the influence of VWC is also considered. The subroutine UMESHMOTION used to implement the wear law is also modified to study the effect of VCOF and VWC. Therefore, in this study, the numerical results of a three-dimensional finite element (FE) model are compared, with analytical results of contact area and contact stresses, and with experimental results of peak wear depth. After validating the FE model, the wear scar, the increasing wear depth, wear volume, and the decreasing contact stress with increasing fretting cycles are determined numerically considering VCOF and VWC using cycle jump approach. The energy dissipation effect of frictional force and fretting amplitude is also studied for varying interaction properties of fretting wear models. The numerical simulations are performed by considering both elastic and plastic material properties to analyse the influence of varying interaction properties on fretting wear models at the running-up stage. The results indicate that the VWC model exhibits comparable impacts on both the elastic and plastic models. The results also show that the VWC fretting wear model leads to higher wear scar, wear volume, and wear depth values at the running-up stage as well as at the steady state stage, which are close to the experimental data.

Influence of fractal-based contact friction coefficient on the stiffness of disc springs: Experimental and numerical studies

In order to study the influence of friction coefficient on the stiffness of disc spring, A series of disc springs ( D = 71 mm) were selected in this paper. The tension and compression experiments of disc spring components were carried out by universal testing machine. The load-displacement characteristic curves of disc springs with different friction surfaces were obtained. The results show that in the loading process, the friction effect hinders the increase of the deformation of the disc spring, so that the actual stiffness of the disc spring is improved and the actual compensation amount is reduced, so this result is worthy of attention. In order to further study the influence of friction coefficient on the loading process of disc spring, according to the load-deformation formula of disc spring in A-L method, the tangential stress caused by friction is added, and the stiffness calculation model of corresponding disc spring is established by Workbench finite element software. The coefficients of different friction surfaces are used as variables for numerical calculation. The results show that the theoretical calculation, numerical calculation and experimental results of stiffness increase with the increase of friction coefficient under 0.55 h (the compensation displacement of A71 disc spring under the working displacement of corrugated tube ±10 mm). Among them, the numerical calculation results are close to the experimental results, and the error value is less than 1%. The numerical calculation results are corrected by using the experimental data, and the corrected model calculation results are in good agreement with the measured results.

Modelling Wear Phenomena Specific to Mixer Blades in Concrete Production Plants

In the cement concrete manufacturing industry, mixers are critical pieces of equipment that play an essential role. Mixers ensure, by mechanically mixing the materials that make up the concrete, the homogeneity of the mixture. Since the active elements of the mixer in the concrete industry—the mixing blades—come into permanent contact with the mineral aggregates in the mixture formed by water and cement, they are permanently subjected to a strong abrasive–erosive wear process. The authors of this article were concerned with the establishment of tribological models for studying the wear of mixing blades, in order to identify the influence of their constructive parameters on the wear intensity. A complex model (Kraghelsky–Nepomnyashchi model) was adopted for the study. The modeling results revealed that the wear intensity decreases with an increasing blade angle of attack and increases linearly with increasing speed, as well as with an increasing friction coefficient. The modeling results confirm that the wear intensity is lowest when the mixing blade is inclined at a 60° angle, while the highest value is recorded for 30°. By identifying the angle at which the greatest wear of blades occurs, interventions can be made in the design of a more durable mixer (with the optimal installation angle of the mixer blades), thus requiring fewer corrective maintenance interventions. Based on these findings, we conclude that the complex model used in the experiment can provide a convenient and efficient tool for the study of erosive–abrasive phenomena.

Microstructure and mechanical properties of WC-12Co cemented carbide fabricated by laser powder bed fusion on a WC-20Co cemented carbide substrate

In this study, WC-12Co cemented carbides were prepared by laser powder bed fusion (LPBF) on a WC-20Co substrate. The effects of the scanning speed and the substrate on the microstructure, mechanical properties and wear characteristics of the WC-12Co cemented carbide were investigated. The results showed that an alternating distribution of coarse and fine WC grains is observed in the LPBF-prepared WC-12Co cemented carbides. As the laser scanning speed decreases or the laser energy density increases, the WC phase gradually decomposes, accompanied by the loss of C and the formation of ƞ phases. WC-12Co cemented carbides produced at a lower scanning speed exhibit a higher density of thermal cracks, while those produced at a higher scanning speed have a larger number of pores. As the laser scanning speed increases, the transverse rupture strength (TRS) first increases to a maximum value of 823.13 MPa and then decreases. The variation of TRS is mainly attributed to the evolution of the brittle ƞ-phase and metallurgical defects. For WC-12Co cemented carbides formed at low scanning speeds, the brittle η-phase may fracture and cut through the matrix during the friction process, leading to an increase in coefficient of friction (COF) and wear mass loss. For samples formed at high scanning speeds, the formation and detachment of the shear layer could accelerate the friction process and undermine the wear resistance of the WC-12Co cemented carbide. Therefore, the sample prepared at the scanning speed of 400 mm/s shows the best wear performance.

Simulating equal channel angular pressing of commercially pure aluminium using Johnson–Cook model

Optimizing the Equal Channel Angular Pressing (ECAP) process for a new material can be a complex endeavour, given the multiple variables such as Coefficient of Friction (COF), channel angle, temperature, etc. To address the need for a material model that can account for temperature-dependent plastic flow, the present study applies the Johnson-Cook plasticity model for simulating ECAP. The present study reports the effects of varying the channel angle (90°, 120°, 150°) and COF (ranging from 0 to 0.15) at room temperature. The results show that the channel angle plays a significant role in influencing the behaviour of the aluminium, with stress and strain exhibiting an inverse relationship with the channel angle. Additionally, the aluminium material experiences a maximum stress distribution and higher flow stress within the COF range of 0 to 0.15 for a channel angle of 90°, as compared to 120° and 150°. This behaviour can be attributed to the restriction of movement at higher COF values. Notably, a maximum shear stress of 56 MPa was observed when the channel angle was set to 90° with a COF of 0.15. Furthermore, across all simulations involving channel angles of 90°, 120°, and 150°, an increase in COF lead to a decrease in curvature. These simulated results are consistent with existing literature. Thus, the Johnson-Cook plasticity model, with appropriate modifications, serves as a viable approach for studying the ECAP process.

Hydraulic investigation of flow and bed load transport in diverging compound channels with rigid and flexible vegetation

Floodplains are really important for the environment as they provide various functions for waterways, including ecological, hydrological, and geomorphic ones. During overbank flows, there are complex hydrodynamic conditions that occur as water interacts with the rough floodplain vegetation and drag forces due to the vegetation that changes the flow pattern. However, we still don't fully understand how floodplain vegetation influences channel-altering hydrodynamic forces and sediment transport. To address this, we conducted flume experiments and measured flow pattern and sediment transport under varied floodplain geometry and rigid and flexible conditions. For this purpose, a physical model was constructed in the laboratory, in which plastic rods with a diameter of 10 mm will be used as trees, and artificial grass will be grass vegetation. Thus, 36 experiments were conducted in which the sedimentation and hydraulic parameters of the flow were calculated by measuring the flow velocity, water surface, and sediment transport rate. The results show that in the floodplain with dense (rigid and flexible) vegetation, the friction coefficient (f) is even 1.5 times higher than in the floodplain without vegetation. The parameters such as flow velocity, bed shear stress and Darcy Weissbach friction coefficient increase in the vertical plane between the main channel and floodplains due to the difference in roughness between the main channel and floodplains. In addition, in the main channel, the flow resistance is almost constant and does not depend on the vegetation density. The Darcy-Weissbach friction coefficient is greatly increased in the presence of grass and tree vegetation on the floodplain, and the larger contribution of f is due to the grass vegetation. The results also showed the sediment transport rate has a direct relationship with the angle of divergence and density of vegetation and an inverse relationship with the relative depth of the flow. Therefore, as the sediment transport rate decreases in the diverging compound channel, the wavelength and height of the dunes increase. At smaller divergence angles, the dunes tend to the top of the zero line (the level of the sediments before the formation of the bed form). In the presence of vegetation, due to the increase in the roughness ratio of the floodplain to the main channel, the contribution of the main channel to the flow rate increases. As a result, the sediment transport rate increases.

Experimental study and numerical simulation analysis of RCS joint with asymmetric friction connection

Based on the seismic design principle of recoverable function and replaceable seismic design, a novel type of reinforced concrete column-steel beam (RCS) joint was proposed, incorporating an asymmetric friction connection in the lower flange of the steel beam. Subsequently, experimental tests, numerical simulations, and theoretical analyses were conducted to evaluate this joint. The test results indicate that the RCS joint with asymmetric friction connection can effectively exert friction slip energy dissipation characteristics, demonstrating good seismic performance in terms of bearing capacity and stiffness. The damage observed in the specimen is primarily focused on the spliced cover plate of the steel beam, with minimal deformation in the core area of the joint. Numerical simulation and parameter analysis were conducted using ABAQUS software. The results demonstrate that the finite element model accurately reproduces the observed phenomena in the test. The parameter analysis reveals that a 10 % increase in bolt preload or a 0.05 increase in friction coefficient can result in a 7 % or 13 % rise in joint bearing capacity, respectively. Finally, a calculation method for determining friction slip in RCS joints with asymmetric friction connection was developed, showing close agreement between the calculated results and finite element outcomes, indicating the accuracy of the formula.

Axial friction coefficient of turbulent spiral Poiseuille flows

Direct numerical simulations of spiral Poiseuille flows in a narrow gap geometry are performed with the aim of identifying the mechanisms governing the dynamics of the axial friction coefficient. The investigation has explored a small portion of the Reynolds number–Taylor number phase space ( $600 \leq Re \leq 5766$ and $1500 \leq Ta \leq 5000$ ), for which reference experimental results are available. The study is focused on the mechanism leading to the enhancement of the axial friction coefficient with the Taylor number when the Reynolds number is kept constant. The analysis of the spatial distribution of the Reynolds stress tensor and of the turbulent energy budget has evidenced the key role of the pressure–strain correlation in the energy transfer from the azimuthal to the axial component. The latter eventually determines the increase of the axial friction coefficient through the enhanced radial mixing of axial momentum. Data have also shown that the flow dynamics is heavily dependent on the $Ta/Re$ ratio, and different regimes develop (ranging from laminar to turbulent), each with peculiar behaviours.

FEM study of blood gold electrically conducting micropolar nanofluid flow within a permeable channel

In this work, Hermite interpolation polynomials are utilized to develop a numerical model to analyze the influence of transport phenomena on blood gold electrically conducting micropolar nanofluid within a permeable channel with chemical reaction and thermal radiation. By considering blood as a micropolar fluid and applying Berman’s similarity transformation the resulting governing equations are transmuted to fourth-order nonlinear ODE which are solved utilizing FEM. The validity of the FEM code is established by comparing the present computations with existing work. Further, the influence of driving parameters are studied and graphically depicted. When utilizing a blood-gold micropolar nanofluid with a 1% volume fraction, it is observed that varying the Hartmann number from 0 to 15 leads to a decline in temperature profiles, resulting in a 2.51% reduction in heat transfer rate. Similarly, an increase in the chemical reaction parameter up to 10 causes species concentration profiles to decrease, leading to an 18.25% reduction in mass transfer rate compared to base fluid. Moreover, an increase in the volume fraction up to 5% results in an increase in coefficient of skin friction under the influence of the Hartmann number. These findings signify the critical role of Hartmann number in controlling blood velocity and chemical reaction parameter assists in lowering the species concentration levels. The results of the present investigation may help analyze flow models related to drug-delivery systems as gold nanoparticles are proficient drug-delivery and drug-carrying medium.

Non-similar analysis of micropolar magnetized nanofluid flow over a stretched surface

The study of micropolar nanofluids unveils intriguing applications, propelled by their exceptional heat transfer capabilities in comparison to conventional fluids. This investigation focuses on analyzing the behavior of magnetized micropolar nanofluid flow over a stretched surface, taking into account crucial factors such as viscous dissipation and heat source. The chosen base fluid is blood, with Copper [Formula: see text] nanoparticles serving as the selected material. Incorporating the single-phase (Tiwari-Das) model with boundary layer assumptions for micropolar nanofluid flow, we introduce the volume fraction of nanoparticles to assess heat transport. The governing system undergoes transformation into a set of dimensionless non-linear coupled differential equations through appropriate transformations. This transformation involves the utilization of a combination of the local non-similarity technique and bvp4c (MATLAB tool) to derive the system of nondimensional partial differential equations (PDEs) for micropolar nanofluid. Our systematic exploration delves into the consequences of nondimensional parameters on velocity, microrotation, and temperature profiles within the boundary layer, including the Eckert number, micropolar parameter, magnetic field parameter, heat source, Prandtl number, and microorganism parameter. Graphical representations vividly demonstrate that the velocity and temperature of micropolar nanofluid increase with the rise in material parameter values, while the microrotation profile decreases. Increasing the magnetic field parameter leads to a reduction in the velocity profile. Moreover, the micropolar temperature profile shows an increase with the rising Eckert number. Crucially, the research emphasizes that factors like the heat source and Eckert number play a role in decreasing the local Nusselt number. In contrast, an increase in the local Nusselt number is observed for material parameters. Furthermore, the skin friction coefficient decreases as micropolar parameter values increase, whereas an increase in the skin friction coefficient is noted for the magnetic field. The primary focus of this research lies in the development of suitable non-similar transformations for the investigated problem, aiming to yield authentic and efficient results. These results hold substantial promise to make meaningful contributions to future research on nanofluid flows.