Increase In Water Permeability Research Articles

Engineering shrinkage resistance of nano-structured hydrogels in seawater for fast uranium capture

Synthetic hydrogels, which are 3D networks composed of crosslinked hydrophilic polymer chains, have been created using various crosslinked ways for uranium capture due to full exposure of chelate functional groups. However, the conventional honeycomb-like hydrogels exhibit non-connected micropore structure, which locks abundant water molecules and hence is unfavorable for mass transfer. Herein, we demonstrate a simple synthesis of the nano-structured hydrogel with activated nanogels as nano-crosslinkers (denoted as PGP hydrogel), and probe into the relationship between hydrogel structural parameters and uranium adsorption kinetics. It is found that the PGP hydrogel with a low crosslinking density of ∼0.02 mol/m3 possesses interconnected micropores, thereby facilitating diffusion of uranyl ions (UO22+) in 3D polymeric networks. Furthermore, a freeze-assisted soaking strategy is proposed to endow PGP hydrogel (denoted as target hydrogel) with strong shrinkage resistance in natural seawater, resulting in a ∼40 % increase in water permeance to reach 369 Lm−2h−1MPa−1. Correspondingly, the adsorption equilibrium time is shortened to ∼11 days. Although the uranium uptake capacity of PGP hydrogels with and without freeze-assisted soaking treatment remain basically unchanged (∼9.73 mg-U/g-Ads), a high uranium adsorption rate of 0.88 mg/g/d for the target hydrogel surpasses most currently available polymer adsorbents. The presented strategy is generalizable to a broader range of applications involving the adsorption of economically valuable ions in seawater or brine lake.

TiO2/AgBr nanocomposite as a novel hydrophilic and photocatalytic modifier in the fabrication of polyethersulfone membrane for wastewater treatment

Enhancing the performance of filtration membranes to improve their antifouling, permeability, and stability is a crucial objective. This can be acquired through the development of innovative materials and methods. With this in mind, the exertion of novel materials is considered a promising approach for modifying polymeric membranes. This study focuses on the potential of incorporating TiO2/AgBr photocatalytic nanocomposites to improve the hydrophilicity, antifouling, and permeability of polyethersulfone (PES) membranes. Following the synthesis of TiO2/AgBr, the study examines its impact on the performance of PES membranes by introducing various concentrations of TiO2/AgBr nanocomposite. Notably, the water contact angle significantly decreases from 68.5° to 44.2°, indicating an improvement in hydrophilicity. This enhanced overall porosity leads to almost a twofold increase in pure water permeability, with the bare membrane registering 78.3 L/m2h.bar and the membrane containing 0.2 wt% TiO2/AgBr achieving 152.4 L/m2h.bar. Due to the photocatalytic activity of TiO2/AgBr, the modified membranes demonstrate promoted antifouling performance, when UV irradiation is used in the washing step of the fouled membranes, as evidenced by the increased flux recovery ratio values, rising from 48 to 60.6 %. The rejection of two different dyes was assessed and the results of 83.9 % and 95.2 % rejection were obtained for Reactive Black 5 (RB5) and Lanasol Red 6G, respectively. Furthermore, the antibacterial activity of TiO2/AgBr was also indicated by confocal microscopy analysis. Thus, embedding TiO2/AgBr not only enhances antifouling properties but also improves the membranes’ ability to reject dyes effectively.

A novel approach for sludge deep-dewatering via flowing-out enhancement but not relying on cell lysis and bound water release

Effective deep-dewatering is crucial for wastewater sludge management. Currently, the dominant methods focus on promoting cell lysis to release intracellular water, but these techniques often lead to secondary pollution and require stringent conditions, limiting their practical use. This study explores an innovative method using a commercially available complex quaternary ammonium salt surfactant, known as G-agent. This agent remarkably reduces the sludge water content from 98.6 % to 56.8 % with a low dosage (50 mg/g DS) and under neutral pH conditions. This approach surpasses Fenton oxidation in terms of dewatering efficiency and avoids the necessity for cell lysis and bound water release, thereby reducing the risk of secondary pollution in the filtrate, including heavy metals, nitrogen, phosphorus, and other contaminants. The G-agent plays a significant role in destabilizing flocs and enhancing flocculation during the conditioning and initial dewatering stages, effectively reducing the solid-liquid interfacial affinity of the sludge. In the compression filtration stage, the agent's solidification effect is crucial in forming a robust skeleton that improves pore connectivity within the filter cake, leading to increased water permeability, drainage performance and water flow-out efficiency. This facilitates deep dewatering of sludge without cell lysis. The study reveals that the G-agent primarily improves water flow-out efficiency rather than water flowability, indicating that cell lysis and bound water release are not indispensable prerequisites for sludge deep-dewatering. Furthermore, it presents an encouraging prospect for overcoming the limitations associated with conventional sludge deep-dewatering processes.

Antifouling performance enhancement of PES membranes using hydrophilic nanoparticles of poly(dopamine-acrylate) for oil/water separation

Polydopamine-acrylate (P(A-D)x) nanoparticles were blended with polyethersulfone (PES) to fabricate a high-performance hybrid ultrafiltration (UF) membrane for the separation of water from oily wastewater. In tris-alkaline buffer solution at room temperature, P(A-D)x nanoparticles were synthesized by intramolecular Michael addition of dopamine with acrylic acid (AA) monomers. Hybrid PES membranes were prepared using P(A-D)x at 0.05–0.4 wt% and characterized using various assays including Field emission scanning electron microscopy (FESEM), Thermogravimetric analysis (TGA), atomic force microscopy (AFM), Fourier transform infrared spectroscopy (FTIR), and water contact angle (WCA). The membranes showed a significant increase in hydrophilicity, water permeability, and oil rejection (R). The primary and secondary pure water fluxes of the membrane with 0.2 wt% P(A-D)0.25 were 45% and 110.78% higher than those of neat PES membrane, respectively. For 3300 ppm oil feed solution, water flux during water/oil separation increased by 107%, while the oil rejection (R) remained at 99.08%. The surface of membrane was markedly hydrophilic, with a WCA about 40°, much lower than that of the neat PES membrane (80.67°). UF hybrid membranes also showed a remarkable reduction in oil adhesion on the membrane surface as well as superior antifouling performance for membranes containing 0.2 wt% P(A-D)0.25, flux recovery ratio (FRR) = 84.88 ± 3.27%, reversible fouling (Rr) = 51.12 ± 1.09%, and irreversible fouling (Rir) = 15.12 ± 3.27%. In addition, the pure water flux was 446% higher than that of the unmodified membrane after five cycles (900 minutes).

A comprehensive review on the use of Ti3C2Tx MXene in membrane-based water treatment

Population growth, industrial activities, and the energy demands of water production intensify the global challenge of accessing clean water. Membrane-based water treatment processes have emerged as crucial solutions to address this crisis, these include microfiltration (MF), ultrafiltration (UF), nanofiltration (NF), forward osmosis (FO), reverse osmosis (RO), and membrane distillation (MD). This review summarizes the properties and use of Ti3C2Tx MXene, a material with notable chemical stability, specific surface area, hydrophilicity, thermal conductivity, and environmental compatibility. Ti3C2Tx fills in the class of two-dimensional materials, it is promising in various membrane processes by offering enhancement in hydrophilicity, permeability, and selectivity. In UF, Ti3C2Tx-based membranes have superior antifouling properties and high rejection rates of contaminants. Meanwhile, in NF, MXene nanosheets elevate the rejection of organics, dyes, and salts, and present valuable nanocomposite membranes. In desalination, incorporating Ti3C2Tx in RO membranes is found to increase water permeability while maintaining high salt rejection in desalination. Also, MXene-modified FO membranes had lower fouling and improved water flux compared with plain membranes, presenting a promising avenue for water purification. Additionally, Ti3C2Tx enhanced water vapor transport and resistance against wetting, which is favorable in MD.This review underscores the transformative potential of Ti3C2Tx MXene in revolutionizing membrane-based water treatment processes, providing innovative solutions to meet the escalating global demand for clean water. Future research directions should optimize MXene-based membrane designs and scale up their production for practical applications in water treatment, thereby contributing to a more sustainable water future.

Sustainable approaches in concrete production: An in-depth review of waste foundry sand utilization and environmental considerations.

This review critically evaluates the potential of Waste Foundry Sand (WFS) as a substitute for fine aggregate in concrete, conducting a comparative analysis of its physical and chemical properties against those of natural sand. The study synthesizes findings from various research experiments to determine concrete's most effective WFS replacement percentage. It compiles and analyzes data on how different WFS ratios affect concrete's mechanical properties, including modulus of elasticity and compressive strength. The review also consolidates research on the impact of WFS on concrete's workability, density, and flowability. A key finding is that WFS, categorized as a non-hazardous waste, possesses a diverse particle size distribution, rendering it suitable for recycling in various industrial applications.The study identifies that a 20%-30% replacement of WFS in concrete significantly improves properties such as voids, specific gravity, and density. However, it is essential to note that exceeding a 30% WFS replacement can result in increased carbonation depth and decreased resistance, primarily due to sulfur trioxide (SO3). Further observations indicate that incorporating higher levels of WFS in self-compacting concrete reduces its flowability and increases water permeability. Moreover, the review highlights the regulatory and classification challenges associated with using WFS, particularly its classification as waste, which hampers its widespread adoption in construction. In conclusion, the study recommends implementing End-of-Waste (EoW) regulations to facilitate sustainable recycling and environmental protection. Additionally, it includes a bibliometric analysis of foundry sand research spanning from 1971 to 2020, providing a comprehensive summary of the field's historical and recent developments.

Understanding the effect of layer spacing on water desalination through two-dimensional covalent organic framework membranes via molecular dynamics simulation

The desalination performance of covalent organic framework (COF) membrane can be tuned through adjusting its layer spacing, which can improve the water permeance while maintaining high ion rejection rate. However, the mechanism of the influence of COF membrane spacing on its seawater desalination performance is still unclear. In this work, the molecular dynamics (MD) simulation were performed to systematically investigate the influence of the layer spacing on desalination performance of AB-stacked MPCOF, including 0.34 nm, 0.44 nm, 0.54 nm and 0.64 nm. The findings indicated a decrease in the resistance of water molecules passing through the AB stacked MPCOF membrane, leading to a significant increase in water permeance as the layer spacing increases. The interlayer spacing of the COF membrane also significantly influenced its interactions with ions. When the layer spacing exceeded 0.44 nm, the ion rejection rate began to decrease. As a result, the AB-stacked MPCOF membranes with 0.44 nm possessed the superior desalination performance, which was much better than other conventional membranes. Our work explored the mechanisms of the effects of COF layer spacing on desalination performance, which might provide valuable suggestions for the optimization of subsequent COF desalination membranes.

Machine learning – Driven surface grafting of thin-film composite reverse osmosis (TFC-RO) membrane

Modifying reverse-osmosis (RO) membrane performance is challenging and time-consuming due to the complex interplay of various factors that influence the membrane's performance. To address this challenge, we have explored the potential of using machine-learning (ML) to graft the polyamide (PA) surface of an RO membrane to increase water permeability and overcome the limitations of the permeability/selectivity tradeoff. We identified moieties with positive and negative contributions toward water permeability by applying Shapley-Additive-exPlanations (SHAP) analysis to our model as an explainable artificial intelligence (XAI) method. We attempted to improve the subunits of the PA's structure with positive Shapley values and graft the polyamide RO membrane layer of a commercial membrane, Dupont XLE, resulting in a substantial increase in water permeability. The membranes were characterized using FTIR, EDS, and SEM analysis, and their performance was evaluated for water permeance and NaCl rejection using a dead-end stirred cell. The modified membrane exhibited a significant improvement in the commercial membrane's water flux, increasing from 2.45 LMH to 4.9 LMH. Our results demonstrate the potential of using ML to replace traditional trial-and-error methods for modifying PA-RO membrane polyamide layers and advancing the development of higher efficient and sustainable RO membranes for water treatment and purification applications.

Establishment of the deuterium oxide dilution method as a new possibility for determining the transendothelial water permeability

Increase in transendothelial water permeability is an essential etiological factor in a variety of diseases like edema and shock. Despite the high clinical relevance, there has been no precise method to detect transendothelial water flow until now. The deuterium oxide (D2O) dilution method, already established for measuring transepithelial water transport, was used to precisely determine the transendothelial water permeability. It detected appropriate transendothelial water flow induced by different hydrostatic forces. This was shown in four different endothelial cell types. The general experimental setup was verified by gravimetry and absorbance spectroscopy. Determination of transendothelial electrical resistance (TEER) and immunocytochemical staining for proteins of the cell-cell contacts were performed to ensure that no damage to the endothelium occurred because of the measurements. Furthermore, endothelial barrier function was modulated. Measurement of transendothelial water flux was verified by measuring the TEER, the apparent permeability coefficient and the electrical capacity. The barrier-promoting substances cyclic adenosine monophosphate and iloprost reduced TEER and electrical capacity and increased permeability. This was accompanied by a reduced transendothelial water flux. In contrast, the barrier-damaging substances thrombin, histamine and bradykinin reduced TEER and electrical capacity, but increased permeability. Here, an increased water flow was shown. This newly established in vitro method for direct measurement of transendothelial water permeability was verified as a highly precise technique in various assays. The use of patient-specific endothelial cells enables individualized precision medicine in the context of basic edema research, for example regarding the development of barrier-protective pharmaceuticals.

Differential Effects of Soy Isoflavones on the Biophysical Properties of Model Membranes.

The effects that the main soy isoflavones, genistein and daidzein, have upon the biophysical properties of a model lipid bilayer composed of 1,2-dioleoyl-sn-glycero-3-phosphocholine (DOPC) or DOPC with cholesterol (4 to 1 mol ratio) have been investigated by transbilayer water permeability, differential scanning calorimetry, and confocal Raman microspectroscopy. Genistein is found to increase water permeability, decrease phase transition temperature, reduce enthalpy of transition, and induce packing disorder in the DOPC membrane with an increasing concentration. On the contrary, daidzein decreases water permeability and shows negligible impact on thermodynamic parameters and packing disorder at comparable concentrations. For a cholesterol-containing DOPC bilayer, both genistein and daidzein exhibit an overall less pronounced effect on transbilayer water permeability. Their respective differential abilities to modify the physical and structural properties of biomembranes with varying lipid compositions signify a complex and sensitive nature to isoflavone interactions, which depends on the initial state of bilayer packing and the differences in the molecular structures of these soy isoflavones, and provide insights in understanding the interactions of these molecules with cellular membranes.

The role of sheet-like TiO2 in polyamide reverse osmosis membrane for enhanced removal of endocrine disrupting chemicals

Thin film composite (TFC) reverse osmosis (RO) membrane shows good promise for treating wastewater containing endocrine disrupting chemical (EDC) pollutants. The incorporation of functional materials with exceptional structural and physico-chemical properties offers opportunities for the membranes preparation with enhanced permselectivity and better antifouling properties. The present study aims to improve the EDC removal efficiency of TFC RO membrane using two-dimensional titania nanosheets (TNS). RO membrane was prepared by incorporating TNS in the dense layer of polyamide (PA) layer to form thin film nanocomposite (TFN) membrane. The TNS loading was varied and the influences on membrane morphology, surface hydrophilicity, surface charge, as well as water permeability and rejection of EDC were investigated. The results revealed that the inclusion of TNS in the membrane resulted in the increase of water permeability and EDC rejection. When treating the mixture of bisphenol A (BPA) and caffeine at 100 ppm feed concentration, the TFN membrane incorporated with 0.05% TNS achieved water permeability of 1.45 L/m2·h·bar, which was 38.6% higher than that of unmodified TFC membrane, while maintaining satisfactory rejection of >97%. The enhancement of water permeability for TFN membrane can be attributed to their hydrophilic surface and unique nanochannel structure created by the nanoscale interlayer spacing via staking of TiO2 nanosheets. Furthermore, the 0.05TFN membrane exhibited excellent fouling resistance towards BPA and caffeine pollutants with almost 100% flux recovery for three cycles of operations.

Construction of PDA-PEI/ZIF-L@PE tight ultra-filtration (TUF) membranes on porous polyethylene (PE) substrates for efficient dye/salt separation

Tight ultra-filtration (TUF) membranes were constructed by in situ growing zinc imidazole frameworks micro-crystalline leaves (ZIF-L) in polyethylene imine (PEI) and polydopamine (PDA) deposit layers on porous polyethylene (PE) substrates. The effects of preparation conditions on the surface physical and chemical structures as well as on the dye/salt separation performance of the formed TUF membranes were systematically investigated. By inserting selective water permeation channels and increasing contacting surface areas, in situ-grown ZIF-L arrays tightly cross-linked in the coating matrix greatly increased water permeation without trading off dye/salt retention selectivity. The morphology of the included ZIF-L particles could be varied by adjusting the ligand/Zn molar ratio (α) in the preparation processes. Optimized PDA-PEI/ZIF-L@PE TUF membranes containing ZIF-L of cross-cross block morphology showed very high pure water permeability of 180 ± 20 L·m−2·h−1·bar−1 (LMHB) and retention selectivity (SCR/Na2SO4 and SMB/Na2SO4) of 267 and 43, respectively, as well as excellent stability and anti-fouling properties.

Long-term stability of cellulose membranes in spent deep eutectic solvent used in the recovery of lignin from lignocellulosic biomass

Deep eutectic solvents (DESs) are a novel class of solvents that can be used to fractionate biomass compounds. However, their sustainability depends strongly on their recyclability. In previous research, it was seen that membrane filtration with commercial cellulose membranes (RC70PP and Ultracel 5 kDa) might be a solution for purification of spent deep eutectic solvent (DES) that has been used in lignin extraction (Choline Chloride: Lactic Acid 1:10 molar ratio) from woody biomass. This DES is, however, very acidic (pH 1.3), which can have detrimental effects on the longevity of the membrane. In a previous study, the time that the membranes were exposed to the spent DES was relatively short. This study aims to increase knowledge of how cellulose membranes withstand spent DES over longer time periods of up to 8 weeks. The results show that cellulose membranes are quite stable under exposure to spent DES in terms of pure water flux and PEG retention for up to 4 weeks. After 8 weeks, the RC70PP membrane demonstrated an increase in pure water permeability of 45% and a noticeable decrease in PEG retention. Surface characterization revealed, however, that the chemical structure of the cellulose membranes changed already after 2 weeks of exposure prior to any changes in pure water permeability were observed. Experimentally revealed esterification of cellulose membrane by Lactic Acid of DES led to more negative charge of the exposed samples compared to their references. This esterification was accompanied by hydrolysis that removed amorphous parts and increased the crystallinity of the membrane.

Enhancing natural gas dehumidification with Pebax/Silica mixed matrix membrane: a comprehensive study

ABSTRACT In this study, a new polymer membrane was developed for natural gas dehumidification using the combination of hydrophilic silica nanoparticles in the Pebax polymer matrix. The membranes were characterized using various analytical methods including FTIR, XRD, SEM, and TGA. The results indicated that adding nanoparticles increased the porosity and thermal stability of the membranes. Also, the enhancement of copolymer hydrophilicity was confirmed by reducing contact angles. The study found that increasing the nanoparticle content from 0 w% to 3 w% at 15 bar pressure resulted in a 33% increase in water permeability and a 12% increase in methane permeability. Adding of silica also increased the H2O/CH4 selectivity from 24.17 to 27.34. Moreover, at higher temperatures (from 25 to 55°C), the permeability of H2O and CH4 reached 171.3 and 10.71 bar, respectively. The findings of this study show that the inclusion of hydrophilic silica nanoparticles in the Pebax matrix can enhance the efficiency of membranes for natural gas dehumidification. Additionally, the study highlights the significance of temperature in the design and implementation of such membranes.

Research of deformation processes of Amu-Bukhara canal and increase of water permeability

Research of deformation processes of Amu-Bukhara canal and increase of water permeability

Effects of pollution of saline soils with oil and oil products on soil physical properties

In the article, pollution of saline soils with oil and oil products, physical and water-physical properties depending on the level of salinity are studied. As a result of the research, it is scientifically based that the increase in the level of contamination of the soil is subject to the decrease in water permeability, and the decrease in the level of pollution is subject to the law of the increase in water permeability. In the article, weakly, moderately, strongly and very strongly contaminated soils with oil were studied. According to the results, it was determined that the water permeability of the soil was observed in 25, 45, 45, 37, 5, 3, 2 minutes, and it carried 75, 26, 44, 45, 540, 1050, 1200 ml of water, respectively, for 90 minutes. The amount of water transfer compared to the control soil for 90 minutes was less in 1%, 2%, 5% contaminated soils, and very high in 15%, 25% and 37.5% contaminated soils. The increase in the level of pollution is explained by the deterioration of water permeability and moisture retention. Also, due to the fact that oil is a viscous organic pollutant, the changes of 0.25, 0.5, 1, 3, 5, 7, 10 mm microaggregates, which are important for soil fertility, as a result of pollution, and changes in the amount of these microaggregates were also determined. It was found that the soils around the South Mirshodi oil field were previously contaminated and the amount of microaggregates smaller than 0.25 mm, 0.25 mm, 1 mm, 2 mm and 3 mm in the irrigated soils increased as the distance from the source of contamination increased. This is explained by the decrease in the concentration of oil in the soil. The amount of 5 mm, 7 mm and 10 mm aggregates has decreased. A similar situation was observed around the Kumkurgan oil base. The effect of petroleum hydrocarbons is more noticeable in microaggregates with a diameter of 10 mm.

The agrophysical properties effects in syderation used short-row sowing on soil

In short-term cotton-crop rotation fields agrophysical features was achieved improvement by sowing pure rape, peas + rape, peas + rape + chick peas are 22–32 tons of biomass per hectare of land is sown in the fall. In particular, when peas + rape, peas + rape + chick peas are used as siderites, macroaggregates in the topsoil increase by 7.87–8.73% and in the subsoil by 3.35–3.50%, when water-resistant aggregates are planted with gooseberry (55.82%) and pea when mixed with rapeseed and peas (56.7%), and increased soil fertility. As a result, the decrease in soil volume had a significant effect on the increase in water permeability and soil moisture more than 2%. The highest moisture content was observed in the mixture of peas + rape + chick peas as a siderite, and when rapeseed was used in its pure form. Sideration has resulted in an increase in organic humus in the soil and an optimal retention of moisture.

Improved flux and anti-fouling performance of a photocatalytic ZnO membrane on porous stainless steel substrate for microalgae harvesting

Photocatalytic self-cleansing ZnO membranes were developed and used for pre-concentrating microalgae solution prior to harvesting. The inorganic membranes were fabricated via two different methods: (i) direct deposition of ZnO onto a porous stainless steel substrate and (ii) post-growth oxidation of a deposited metallic Zn layer. Systematic surface characterisation revealed a thin layer of homogeneous, crystalline ZnO on the porous membrane. Direct ZnO deposition resulted in a thicker layer with higher UV light absorption capability compared with the post-growth oxidization method. The ZnO coating made the membrane surface highly hydrophilic, resulting in two-fold increase in water permeance compared to the base stainless steel substrate. The high hydrophilicity of the ZnO-coated membrane also led to an increase in the permeate flux of the microalgae solution by up to 100%, making it suitable for microalgae pre-concentration. Upon UV light irradiation, the ZnO membrane demonstrated self-cleansing capability due to the photocatalytic activity of the ZnO coating layer. After 30 min of UV irradiation, the ZnO membrane could achieve 60% permeance recovery after complete fouling. No recovery was observed with the base stainless steel membrane, which was used as the control.

Illuminating plant water dynamics: the role of light in leaf hydraulic regulation.

Light intensity and quality influence photosynthesis directly but also have an indirect effect by increasing stomatal apertures and enhancing gas exchange. Consequently, in areas such as the upper canopy, a high water demand for transpiration and temperature regulation is created. This paper explores how light intensity and the natural high Blue-Light (BL) : Red-Light (RL) ratio in these areas, is important for controlling leaf hydraulic conductance (Kleaf ) by BL signal transduction, increasing water permeability in cells surrounding the vascular tissue, in supporting the enormous water demands. Conversely, shaded inner-canopy areas receive less radiation, have lower water and cooling demands, and exhibit reduced Kleaf due to diminished intensity and BL induction. Intriguingly, shaded leaves display higher water-use efficiency (compared with upper-canopy) due to decreased transpiration and cooling requirements while the presence of RL supports photosynthesis.

Comparison of 2D and 3D materials on membrane modification for improved pressure retarded osmosis (PRO) process

Pressure retarded osmosis (PRO) is a sustainable process that convert Gibbs free energy to osmotic energy by mixing two solutions of different salinities. The main challenges in the design of PRO membranes are obtaining a membrane with high water permeability and low salt permeability but also very high mechanical strength because the PRO process involves high pressure on the draw solution. Commercially available RO membranes with potential utility in a PRO system exhibit a high salt rejection rate but low water permeability and mechanical stability. Surface modification is a promising strategy for tuning the fundamental properties of the membranes (e.g. hydrophilicity, surface charge and thickness) that can improve the filtration performance of the membranes. The coating layer can also improve the mechanical stability of the membranes. Therefore, in this work, various types of modification materials were applied to the commercial available RO membranes to enhance their performance.With the assistance of hydrophilic materials (e.g. polydopamine – PDA), filtration performance of the membranes can be increased through membrane modification by 2D materials with high charge intensities (e.g. polyelectrolytes and graphene oxides) and by 3D mesoporous materials (e.g. zeolites), which increases the thickness of the membrane that can be beneficial in mechanically reinforcing the membrane. In this work, we modified commercial RO membrane with PDA, polyelectrolytes, graphene oxide and zeolites (ZSM-5). Improved filtration performance (increased water permeability and maintained salt permeability) of the modified membrane was observed. Tensile tests showed enhanced mechanical strength of the modified membranes, especially following 3D zeolites modification (up to 35 % of higher tensile strain was reported). Interestingly, a lower concentration of PDA (2 mg/mL) and zeolites resulted in higher mechanical strength of the modified membranes. Such results were likely due to a more homogenous coating layer when a low modifier concentration was applied. The thin and uniform layer can better absorb energy when membranes are under high pressure.