Immobilization Of Peroxidase Research Articles

Multi-walled carbon nanotubes in aqueous phytic acid for enhancing biosensor

The poor dispersion of carbon based nanomaterials without strong acid pretreatment in aqueous solution is a fundamental problem, limiting its applications in biology-related fields. A good dispersion of multi-walled carbon nanotubes (MWCNTs) in water was realized by 50 wt.% phytic acid (PA) solution. As an application case, the PA–MWCNTs dispersion in aqueous solution was used for the immobilization of horseradish peroxidase (HRP) and its direct electrochemistry was realized. The constructed biosensor has a sound limit of detection, wide linear range, and high affinity for hydrogen peroxide (H2O2) as well as being free from interference of co-existing electro-active species.

Direct Electrochemistry and Electrocatalysis of Horseradish Peroxidase Immobilized in a DNA/Chitosan-Fe3O4 Magnetic Nanoparticle Bio-Complex Film

A DNA/chitosan-Fe3O4 magnetic nanoparticle bio-complex film was constructed for the immobilization of horseradish peroxidase (HRP) on a glassy carbon electrode. HRP was simply mixed with DNA, chitosan and Fe3O4 nanoparticles, and then applied to the electrode surface to form an enzyme-incorporated polyion complex film. Scanning electron microscopy (SEM) was used to study the surface features of DNA/chitosan/Fe3O4/HRP layer. The results of electrochemical impedance spectroscopy (EIS) show that Fe3O4 and enzyme were successfully immobilized on the electrode surface by the DNA/chitosan bio-polyion complex membrane. Direct electron transfer (DET) and bioelectrocatalysis of HRP in the DNA/chitosan/Fe3O4 film were investigated by cyclic voltammetry (CV) and constant potential amperometry. The HRP-immobilized electrode was found to undergo DET and exhibited a fast electron transfer rate constant of 3.7 s−1. The CV results showed that the modified electrode gave rise to well-defined peaks in phosphate buffer, corresponding to the electrochemical redox reaction between HRP(Fe(III)) and HRP(Fe(II)). The obtained electrode also displayed an electrocatalytic reduction behavior towards H2O2. The resulting DNA/chitosan/Fe3O4/HRP/glassy carbon electrode (GCE) shows a high sensitivity (20.8 A·cm−2·M−1) toward H2O2. A linear response to H2O2 measurement was obtained over the range from 2 μM to 100 μM (R2 = 0.99) and an amperometric detection limit of 1 μM (S/N = 3). The apparent Michaelis-Menten constant of HRP immobilized on the electrode was 0.28 mM. Furthermore, the electrode exhibits both good operational stability and storage stability.

Simple approach for the immobilization of horseradish peroxidase on poly-l-histidine modified reduced graphene oxide for amperometric determination of dopamine and H2O2

In this work, immobilization of horseradish peroxidase (HRP) on poly-l-histidine (P-l-His) modified reduced graphene oxide (RGO) was demonstrated.

Preparation of core-shell Fe3O4@poly(dopamine) magnetic nanoparticles for biosensor construction.

Novel core-shell Fe3O4@poly(dopamine) magnetic nanoparticles were prepared through an in situ self-polymerization method. The hybrid nanomaterial showed an average core diameter of 11 ± 3 nm and a polymer thin film thickness of 1.8 ± 0.2 nm. The core-shell nanoparticles were employed as solid supports for the covalent immobilization of horseradish peroxidase (HRP), and the resulting biofunctionalized magnetic nanoparticles were employed to construct an amperometric biosensor for H2O2. The enzyme biosensor showed a high sensitivity of 442.14 mA M-1 cm-2, a low limit of detection of 182 nM, a wide linear range from 6.0 × 10-7 to 8.0 × 10-4 M and high stability for 1 month.

Immobilization of chemically modified horse radish peroxidase within activated alginate beads

Immobilization of horse radish peroxidase (HRP) within alginate beads was improved by chemical modification of the enzyme and polysaccharide chains. HRP and alginate were oxidized by periodate and subsequently modified with ethylenediamine. Highest specific activity of 0.43 U/ml of gel and 81 % of bound enzyme activity was obtained using aminated HRP and alginate oxidized by periodate. Immobilized enzyme retained 75 % of original activity after 2 days of incubation in 80 % (v/v) dioxane and had increased activity at basic pH values compared to native enzyme. During repeated use in batch reactor for pyrogallol oxidation immobilized peroxidase retained 75 % of original activity.

Direct electrochemistry of horseradish peroxidase based on hierarchical porous calcium phosphate microspheres

Biomorphic calcium phosphate (CaP) microspheres with hierarchical porous structure were synthesized using natural cole pollen grains as templates and were further employed for the immobilization of horseradish peroxidase (HRP). Scanning electron microscopy and Fourier transform infrared spectroscopy revealed (a) the porous structure of the CaP microspheres, (b) the effective immobilization, and (c) the retention of the conformation of HRP on CaP. The immobilized HRP was placed on a glassy carbon electrode where it underwent a direct, fully reversible, and surface-controlled redox reaction with an electron transfer rate constant of 1.96 s−1. It also exhibits high sensitivity to the reduction of H2O2. The response to H2O2 is linear in the 5.00 nM to 1.27 μM concentration range, and the sensitivity is 30357 μA⋅mM−1⋅cm−2. The detection limit (at an SNR of 3) is as low as 1.30 nM. The apparent Michaelis–Menten constant (KMapp) of the immobilized enzyme is 0.92 μM. This new CaP with hierarchical porous structure therefore represents a material that can significantly promote the direct electron transfer between HRP and an electrode, and is quite attractive with respect to the construction of biosensors.

Incubation-free electrochemical immunoassay for diethylstilbestrol in milk using gold nanoparticle-antibody conjugates for signal amplification

We report on a novel enzyme-enhanced label for the electrochemical determination of diethylstilbestrol (DES). The label was obtained by orientation-controlled immobilization of a multiplex horseradisch peroxidase (HRP) conjugated polymer on gold nanoparticles (AuNPs) using the Envision reagent (EV) which is an enzyme-polymer complex that contains HRP and anti-IgG antibody in a polydextrin amine skeleton. The AuNPs were modified with Concanavalin A (Con A) and served as a carrier for immobilization of the EV−DES antibody composite. This resulted in a bioconjugate of the type AuNP−Con A−EV−DES Ab which was employed as the label. On exposure to samples containing DES, a sandwich immunocomplex is formed between antibody against DES (which was immobilized on a glassy carbon electrode and is acting as a capture probe), DES (the analyte), and the above label as the signal tracer. Hemin was used as an electronic mediator in the reaction of HRP. The HRP on the label catalyzes the oxidative formation of hydrogen peroxide at pH 7.0, and this induces an increased reductive current in the presence of hemin as an electron mediator. Under optimal conditions, the current increases linearly with increasing concentrations of DES in the range from 5 to 500 pg · mL−1, with a detection limit as low as 2 pg · mL−1 (at an S/N of 3). The method exhibits high selectivity and good stability. It works without incubation so that the time for an assay is shortened to 5 min. The assays was successfully applied to the determination of DES in milk samples.

Immobilization of horseradish peroxidase in phospholipid-templated titania and its applications in phenolic compounds and dye removal

In this study, horseradish peroxidase (HRP) was encapsulated in phospholipid-templated titania particles through the biomimetic titanification process and used for the treatment of wastewater polluted with phenolic compounds and dye. The encapsulated HRP exhibited improved thermal stability, a wide range of pH stability and high tolerance against inactivating agents. It was observed an increase in Km value for the encapsulated HRP (8.21mM) when compared with its free counterpart. For practical applications in the removal of phenolic compounds and dye by the encapsulated HRP, the removal efficiency for phenol, 2-chlorophenol, Direct Black-38 were 92.99%, 87.97%, and 79.72%, respectively, in the first treatment cycle. Additionally, the encapsulated HRP showed better removal efficiency than free HRP and a moderately good capability of reutilization.

A simple and sensitive immunoassay for the determination of human chorionic gonadotropin by graphene-based chemiluminescence resonance energy transfer

In this study, we report a strategy of chemiluminescence resonance energy transfer (CRET) using graphene as an efficient long-range energy acceptor. Magnetic nanoparticles were also used in CRET for simple magnetic separation and immobilization of horseradish peroxidase (HRP)-labeled anti-HCG antibody. In the design of CRET system, the sandwich-type immunocomplex was formed between human chorionic gonadotropin (HCG, antigen) and two different antibodies bridged the magnetic nanoparticles and graphene (acceptors), which led to the occurrence of CRET from chemiluminescence light source to graphene. After optimizing the experimental conditions, the quenching of chemiluminescence signal depended linearly on the concentration of HCG in the range of 0.1mIUmL−1–10mIUmL−1 and the detection limit was 0.06mIUmL−1. The proposed method was successfully applied for the determination of HCG levels in saliva and serum samples, and the results were in good agreement with the plate ELISA with colorimetric detection. It could also be developed for detection of other antigen–antibody immune complexes by using the corresponding antigens and respective antibodies.

Preparation of boronate-functionalized molecularly imprinted monolithic column with polydopamine coating for glycoprotein recognition and enrichment

A novel imprinting strategy using reversible covalent complexation of glycoprotein was described for creating glycoprotein-specific recognition cavities on boronate-functionalized monolithic column. Based on it, a molecularly imprinted monolithic column was prepared by self-polymerization of dopamine (DA) on the surface of 4-vinylphenylboronic acid (VPBA)-based polymeric skeletons after reversible immobilization of horseradish peroxidase (HRP). Due to the combination of boronate affinity and surface imprinting of DA, the stable and accessible recognition sites in the as-prepared imprinted monolith could be obtained after the removal of the template, which facilitated the rebinding of the template and provided good reproducibility and lifetime of use. The recognition behaviors of proteins on the bare VPBA-based, HRP-imprinted and nonimprinted monolithic columns were evaluated in detail and the results showed that the HRP-imprinted monolith exhibited higher recognition ability toward the template than another two monolithic columns. Not only nonglycoproteins but also glycoproteins can be well separated with the HRP-imprinted monolith. In addition, the feasibility of the HRP-imprinted monolith, adopted as an in-tube solid phase microextraction (in-tube SPME), was further assessed by selective extraction and enrichment of HRP from human serum. The good results demonstrated its potential in glycoproteome analysis.

Titanium dioxide nanorod-based amperometric sensor for highly sensitive enzymatic detection of hydrogen peroxide

Titanium dioxide nanorods (TNR) were grown on a titanium electrode by a hydrothermal route and further employed as a supporting matrix for the immobilization of nafion-coated horseradish peroxidase (HRP). The strong electrostatic interaction between HRP and TNR favors the adsorption of HRP and facilitates direct electron transfer on the electrode. The electrocatalytic activity towards hydrogen peroxide (H2O2) was investigated via cyclic voltammetry and amperometry. The biosensor exhibits fast response, a high sensitivity (416.9 μA·mM−1), a wide linear response range (2.5 nM to 0.46 mM), a detection limit as low as 12 nM, and a small apparent Michaelis-Menten constant (33.6 μM). The results indicate that this method is a promising technique for enzyme immobilization and for the fabrication of electrochemical biosensors.

Soybean hull peroxidase immobilization on macroporous glycidyl methacrylates with different surface characteristics

Soybean hull peroxidase (SHP, E.C. 1.11.1.7) was immobilized by a glutaraldehyde and periodate method onto series of macroporous copolymers of glycidyl methacrylate (GMA) and ethylene glycol dimethacrylate (EGDMA), poly(GMA-co-EGDMA) with various surface characteristics and pore size diameters ranging from 44 to 200nm. Glutaraldehyde immobilization method and poly(GMA-co-EGDMA) named SGE 20/12 with pore sizes of 120nm gave immobilized enzyme with highest specific activity of 25U/g. Deactivation studies showed that immobilization increased stability of SHP and that surface characteristics of the used copolymer had a major influence on a stability of immobilized enzyme at high temperatures and in an organic solvent. The highest thermostability was obtained using the copolymer SGE 20/12 with pore size of 120nm, while the highest stability in dioxane had SHP immobilized onto copolymer SGE 10/4 with pore size of 44nm. Immobilized SHP showed a wider pH optimum as compared to the native enzyme especially at alkaline pH values and 3.2 times increased K m value for pyrogallol. After 6 cycles of repeated use in batch reactor, immobilized SHP retained 25% of its original activity. Macroporous copolymers with different surface characteristics can be used for fine tuning of activity and stability of immobilized SHP to obtain a biocatalyst suitable for phenol oxidation or polymer synthesis in organic solvents.

Immobilization of horseradish peroxidase on electrospun microfibrous membranes for biodegradation and adsorption of bisphenol A

Horseradish peroxidase (HRP) from roots of horseradish (Amoracia rusticana) was successfully immobilized on novel enzyme carriers, poly(methyl methacrylate-co-ethyl acrylate) (PMMA CEA) microfibrous membranes, and used for removal of bisphenol A from water. PMMA CEA fibrous membranes (PFM) with fiber diameters of 300-500 nm, were fabricated by electrospinning. HRP was covalently immobilized on the surface of microfibers previously activated by polyethylenimine and glutaraldehyde. HRP loading reached 285 mg/g, and enzyme activity was 70% of free HRP after immobilization. Both stabilities and reusability of HRP were greatly improved after immobilization. After six repeated runs, immobilized HRP retained about 50% of its initial activity. Immobilized HRP exhibited significantly higher removal efficiency for bisphenol A (BPA) in 3h (93%) compared with free HRP (61%) and PFM alone (42%). The high BPA removal can be resulted by improvement of catalytic activity of immobilized HPR with adsorption on modified PMMA CEA support.

A silica-dextran nanocomposite as a novel matrix for immobilization of horseradish peroxidase, and its application to sensing hydrogen peroxide

We report on a novel matrix of solgel organic–inorganic nanocomposite that was fabricated from silica sol gel and dextran. It was used for the immobilization of horseradish peroxidase (HRP) to give a biosensor for hydrogen peroxide (H2O2). The sensor film was characterized by Fourier transform infrared and UV–vis spectroscopy with respect to structural features and the conformation of the enzyme. The topographies of the surface of the electrode were investigated by field emission scanning electron microscopy. The biosensor was used to determine H2O2 quantitatively in the presence of Methylene blue as a mediator with high electron transfer efficiency. A pair of stable and well defined quasi-reversible redox peaks of the HRP [Fe (III)]/HRP [Fe (II)] redox couple was observed at pH 7.0. The biosensor responds to H2O2 in the 0.5 mM to 16.5 mM concentration range, and the limit of detection is 0.5 mM.

Immobilization and catalytic activity of horseradish peroxidase on molybdenum disulfide nanosheets modified electrode

This communication reports the application of layer-structured MoS2 as matrix for enzyme immobilization and biosensor construction. MoS2 nanosheets were prepared using ultrasonic exfoliation in solvent mixture. Data from UV–vis spectra, scanning electron microscopy and transmission electron microscopy demonstrate that the as-prepared MoS2 nanomaterial has ordered layer-structure. The negative charges carried by the MoS2 nanosheets are then used to immobilize horseradish peroxidase (HRP) via the electrostatic attraction, forming HRP–MoS2 hybrid. FTIR spectra indicate that the immobilized HRP retains its native structure. The HRP–MoS2 hybrid modified glassy carbon electrode shows good electrocatalytic activity toward H2O2 reduction. This work suggests that MoS2 nanosheets are a potential candidate for efficient enzyme immobilization and promising in biosensing and biocatalytic applications.

An amperometric biosensor utilizing a ferrocene-mediated horseradish peroxidase reaction for the determination of capsaicin (chili hotness).

Chili hotness is very much dependent on the concentration of capsaicin present in the chili fruit. A new biosensor based on a horseradish peroxidase enzyme-capsaicin reaction mediated by ferrocene has been successfully developed for the amperometric determination of chili hotness. The amperometric biosensor is fabricated based on a single-step immobilization of both ferrocene and horseradish peroxidase in a photocurable hydrogel membrane, poly(2-hydroxyethyl methacrylate). With mediation by ferrocene, the biosensor could measure capsaicin concentrations at a potential 0.22 V (vs. Ag/AgCl), which prevented potential interference from other electroactive species in the sample. Thus a good selectivity towards capsaicin was demonstrated. The linear response range of the biosensor towards capsaicin was from 2.5–99.0 μM with detection limit of 1.94 μM. A good relative standard deviation (RSD) for reproducibility of 6.4%–9.9% was obtained. The capsaicin biosensor demonstrated long-term stability for up to seven months. The performance of the biosensor has been validated using a standard method for the analysis of capsaicin based on HPLC.

Enzymatic Decolorization of Anthraquinone and Diazo Dyes Using Horseradish Peroxidase Enzyme Immobilized onto Various Polysulfone Supports

In this study, covalent immobilization of the horseradish peroxidase (HRP) onto various polysulfone supports was investigated. For this purpose, different polysulfones were methacrylated with methacryloyl chloride, and then, nonwoven fabric samples were coated by using solutions of these methacrylated polysulfones. Finally, support materials were immersed into aquatic solution of HRP enzyme for covalent immobilization. Structural analysis of enzyme immobilization onto various polysulfones was confirmed with Fourier transform infrared spectroscopy, atomic force microscopy, and proton nuclear magnetic resonance spectroscopy. Decolorization of textile diazo (Acid Black 1) and anthraquinone (Reactive Blue 19) dyes was investigated by UV-visible spectrophotometer. Covalently immobilized enzyme has been used seven times in freshly prepared dye solutions through 63 days. Dye decolorization performance of the immobilized systems was observed that still remained high (70%) after reusing three times. Enzyme activities of immobilized systems were determined and compared to free enzyme activity at different conditions (pH, temperature, thermal stability, storage stability). Enzyme activities of immobilized systems and free enzyme were also investigated at the different temperatures and effects of temperature and thermal resistance for different incubation time at 50 °C. In addition, storage activity of free and immobilized enzymes was determined at 4 °C at different incubation days.

Degradation of direct azo dye by Cucurbita pepo free and immobilized peroxidase

Enzymatic decolourization of the azo dye, Direct Yellow (DY106) by Cucurbita pepo (courgette) peroxidase (CP) is a complex process, which is greatly affected by pH, temperature, enzyme activity and the concentrations of H2O2 and dye. Courgette peroxidase was extracted and its performance was evaluated by using the free-CP (FCP) and immobilized-CP (ICP) forms in the decolourization of DY106. Immobilization of peroxidase in calcium alginate beads was performed according to a strategy aiming to minimize enzyme leakage and keep its activity at a maximum value by optimizing sodium alginate content, enzyme loading and calcium chloride concentration. The initial conditions at which the highest DY106 decolourization yield was obtained were found at pH 2, temperature 20°C, H2O2 dose 1 mmol/L (FCP) and 100 mmol/L (ICP). The highest decolourization rates were obtained for dye concentrations 50 mg/L (FCP) and 80 mg/L (ICP). Under optimal conditions, the FCP was able to decolorize more than 87% of the dye within 2 min. While with ICP, the decolourization yield was 75% within 15 min. The decolourization and removal of DY106 was proved by UV-Vis analysis. Fourier transform infrared (FT-IR) spectroscopy analysis was also performed on DY106 and enzymatic treatment precipitated byproduct.

Self-Assembled Au Electrode for Direct Electrochemistry of Horseradish Peroxidase and Detection of Hydrogen Peroxide

The H2O2 biosensor was prepared by continuous processes: 2,3-dimercaptosuccinic acid (DMSA) self-assembly monolayers gold nanoparticles (AuNPs) film by electrodepositioncovalent immobilization of horseradish peroxidase (HRP). In pH 7.2 phosphoric buffer solution (PBS), the HRP-AuNPs-DMSA-Au electrode exhibited a pair of well-defined cyclic voltammetric peaks in H2O2 solution, and the oxidation peak is about +0.4V versus saturated calomel electrode (SCE). The resulting substrates were characterized by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The biosensor exhibited remarkable sensitivity towards H2O2 and a wide dynamic range of 2-800 μM. The electrode retained 90% of its initial activity after 30 days of storage at 4°C.

Immobilization of horseradish peroxidase on zinc oxide nanorods grown directly on electrodes for hydrogen peroxide sensing

An amperometric biosensor for hydrogen peroxide detection was developed by immobilization of horseradish peroxidase on zinc oxide nanorods directly grown on the electrode. The ZnO nanorods were fabricated by electrodepositing ZnO nanoseeds on indium tin oxide glass followed by a hydrothermal growth process. The ZnO nanorods were used to increase the specific surface area for carrying horseradish peroxidase and to build direct electron transfer channels to the electrode. The structure of the ZnO nanorods on indium tin oxide was studied by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and the electrochemical behaviors were carefully examined. The result showed that the biosensor responds well to hydrogen peroxide in a wide range of concentration. The linear range is from 0.5 to 9.0 mM with a limit of detection (S/N = 3) of 0.3 mM, and the response time is about 7 s, which indicates that ZnO nanorods are promising supporting materials to build direct electron transfer biosensors.