Hydrogen Adsorption Energy Research Articles

Neighboring Catalytic Sites Are Essential for Electrochemical Dechlorination of 2-Chlorophenol.

The electrocatalytic reduction process is a promising technology for decomposing chlorinated organic pollutants in water but is limited by the lack of low-cost catalysts that can achieve high activity and selectivity. In studying electrochemical dechlorination of 2-chlorophenol (2-CP) in aqueous media, we find that cobalt phthalocyanine molecules supported on carbon nanotubes (CoPc/CNT), which is a highly effective electrocatalyst for breaking the aliphatic C-Cl bonds in 1,2-dichloroethane (DCA) and trichloroethylene (TCE), are completely inactive for reducing the aromatic C-Cl bond in 2-CP. Detailed mechanistic investigation, including volcano plot correlation between dechlorination rate and atomic hydrogen adsorption energy on various transition metal surfaces, kinetic measurements, in situ Raman spectroscopy, and density functional theory calculations, reveals that the reduction of the aromatic C-Cl bond in 2-CP goes through a hydrodechlorination mechanism featuring a bimolecular reaction between adsorbed atomic hydrogen and 2-CP on the catalyst surface, which requires neighboring catalytic sites, whereas the aliphatic C-Cl bonds in DCA and TCE are cleaved by direct electron transfer from the catalyst, which can occur on isolated single sites. This investigation leads to the discovery of metallic Co as a highly selective and active electrocatalyst for 2-CP dechlorination. This work provides new insights into the fundamental chemistry and catalyst design of electrochemical dechlorination reactions for wastewater treatment.

Unlocking Enhanced Electrochemical Performance of MBene-MoB Through Controlled Aluminum Dissipation from MoAlB.

2D transition metal borides, known as MBenes, have attracted considerable attention due to their exceptional properties. This study explores the feasibility of aluminum (Al) etching from MoAlB using environmentally friendly and sustainable fluoride-free dilute acidic/alkaline solutions at room temperature, revealing its thermodynamic and kinetic viability. Furthermore, it is found that complete removal of Al can be achieved in dilute alkaline reagent under hydrothermal conditions, yielding pristine single/few-layered MBene-MoB for the first time, while acidic solutions result in ≈33% etching rates. XRD refinement, which tracks aluminum removal from 0% to 100%, reveals transient metastable phases of MoAl1-xB (x<0.5) in the initial etching stages, evolving into relatively stable pure Mo2AlB2 structures with 50% Al deficiency, serving as a precursor to MBenes. The subsequent loss of Al results in a 2D MBene-MoB structure. DFT calculations confirm excellent conductivity for MoAlB, MoAl1-xB (x=0-1), and MBene-MoB. Remarkably, MBene-MoB exhibits superior supercapacitor performance with a 4025.60mFcm-2/201.28Fg-1 capacitance. Simulations validate rapid electrolyte diffusion in layered MBene-MoB, contributing significantly to enhanced capacitance. Additionally, in the hydrogen evolution reaction (HER), MBene-MoB demonstrates superior catalytic activity compared to the precursor MoAlB and commercial MoB. Calculations suggest the potential for enhancing HER through surface modulation, considering its suboptimal hydrogen adsorption energy.

Symbolic transform optimized convolutional neural network model for high-performance prediction and analysis of MXenes hydrogen evolution reaction catalysts

Two-dimensional MXenes materials are expected to be cost-effective and efficient catalysts for hydrogen evolution reaction (HER) due to their tunable surface electronic structure. To optimize its catalytic activity, this study proposes a data-driven framework (CROSST) to generate descriptors through feature engineering and integrate them into a convolutional neural network to predict the HER performance of transition-metal (TM) anchored bis-transition-metal carbon-nitride (TM-M′2M′′CNO2) catalysts. The STCNN model achieves a coefficient of determination of more than 0.93, showing the ability to predict the Gibbs free energy of hydrogen adsorption (ΔGH) with high accuracy. We explored the microscopic mechanisms of HER activity through density functional theory and machine learning analysis. It was found that TM anchoring altered the charge distribution of the MXenes material, elevated the atomic orbital occupancy of neighboring O sites, and weakened the O adsorption of H, thus affecting the HER activity. These results provide a theoretical basis for the design of high-performance MXenes HER catalysts and contribute new research perspectives.

Nanocrystalline transition metal tetraborides as efficient electrocatalysts for hydrogen evolution reaction at the large current density

While great efforts have been made to improve the electrocatalytic activity of existing materials toward hydrogen evolution reaction (HER), it is also importance for searching new type of nonprecious HER catalysts to realize the practical hydrogen evolution. Herein, we firstly report nanocrystalline transition metal tetraborides (TMB4, TM=W and Mo) as an efficient HER electrocatalyst has been synthesized by a single-step solid-state reaction. The optimized nanocrystalline WB4 exhibits an overpotential as low as 172 mV at 10 mA/cm2 and small Tafel slope of 63 mV/dec in 0.5 M H2SO4. Moreover, the nanocrystalline WB4 outperforms the commercial Pt/C at high current density region, confirming potential applications in industrially electrochemical water splitting. Theoretical study reveals that high intrinsic HER activity of WB4 is originated from its large work function that contributes to the weak hydrogen-adsorption energy. Therefore, this work provides new insights for development of robust nanocrystalline electrocatalysts for efficient HER.

Novel Graphene-Based Reversible Physisorption Materials for High Hydrogen Uptake

Carbon-based nanomaterials (graphene, carbon nanotube, microporous carbon, graphitic carbon etc.) are excellent H2 storage materials due to high molecular H2 uptake at the micropores and large H2 adsorption at the graphene network via the formation of dipoles in H2 molecules through London dispersion forces. On the other hand, incorporation of transition metal nanoparticles within the nanocarbon network facilitates dissociation of H2 molecules into constituents H-atoms over the metal nanoparticles, followed by diffusion into the carbon nano-matrix via ‘spill-over’ effect for polarization/hybridization of metal-hydrogen to create high H2 binding energy for high hydrogen adsorption. Therefore, a nanocomposite of graphene-microporous carbon-metal nanoparticle network is expected to deliver excellent H2 uptake capacity and acts as a novel reversible physisorption material for hydrogen storage applications, which is very important for sustainable renewable energy integration.A simple, cost effective sputtering method is used to fabricate metal incorporated graphitic microporous carbon film and differential resistance measurement showed high H2 uptake. Average number of graphene layer formation is dependent on sputtering parameters, which manifest bi-to-multilayer graphene. With increase in graphene layers, H2 adsorption also increases due to a fourfold effect: higher molecular hydrogen uptake at the graphene layers, more active sites into the micropores, promotion of molecular dissociation into atomic hydrogen by the metal nanoparticles, and the formation of hydrogenated carbon via destruction of the π-bonds.

Enhancement of hydrogen evolution activity of CoS2/MoS2 heterostructure catalysts by electronic structure modulation

MoS2 exhibits high catalytic ability; however, its wide band gap (1.73 eV) and poor intrinsic conductivity significantly restrict the enhancement of its catalytic activity. To enhance the electron transfer between the interface of heterojunctions and improve the hydrogen evolution reaction (HER) performance, the paper constructs a CoS2/MoS2 heterostructures by growing CoS2/MoS2-X on carbon cloth (CC) using a straightforward one-step method. It investigates the HER properties of the heterojunctions of various molar ratios of ammonium molybdate to cobalt nitrate. The results indicate that the CoS2/MoS2-X catalyst exhibits excellent electrocatalytic activity (73 mV@10 mA cm−2) and Tafel slope (80.42 mV dec−1) at 1.0 M KOH when the molar ratio of ammonium molybdate to cobalt nitrate is 1:1 (X = 5). CoS2/MoS2-5 exhibits good durability of over 100 h when current densities are 10 and 100 mA cm−2. Density functional theory (DFT) calculations indicate that heterostructures present an optimized Gibbs free energy of hydrogen adsorption (ΔGH*) close to zero, providing insight into the exceptional HER performance. This work provides a simple, effective and innovative strategy for preparing high-activity CoS2/MoS2 catalysts by modulation of electronic structure.

Facile hydrothermal synthesis of ZnIn2S4/TiO2 nanosheets for promoted hydrogen evolution reaction

The current study was conducted by introducing a narrow bandgap semiconductor, ZnIn2S4, with the goal of addressing the inefficiency of hydrolysis dissociation and the limited visible light absorption capacity faced by TiO2 as a hydrogen evolution reaction (HER) catalyst due to its low conduction band position and wide bandgap. Using a one-step hydrothermal process, ZnIn2S4 nanosheet/TiO2 nanorod heterostructures were built on nickel foam substrates. The nanosheet structure of ZnIn2S4 is shaped like a flower, which greatly increased the roughness of the TiO2 surface and revealed additional active sites. The ZnIn2S4/TiO2 heterostructure demonstrates quick reaction kinetics and effective electron transport capability, as demonstrated by the electrochemical test results. An overpotential of just 195 mV is required to obtain a current density of 10 mA cm−2. In addition, the overpotential is further decreased to 160 mV under simulated solar radiation. Furthermore, ZnIn2S4 addition minimizes the free energy of hydrogen adsorption on the TiO2 surface and optimizes the position of its Fermi energy level, improving the usage of photogenerated carriers, according to density functional theory (DFT) calculations. This work validates the prospective use of ZnIn2S4/TiO2 heterostructures in photoelectrocatalysis and offers a fresh viewpoint for developing high-performance HER catalysts.

Room-temperature hydrogen adsorption in Pd nanoparticle decorated UiO-66-NH2 via spillover

To improve room-temperature hydrogen storage, palladium (Pd) nanoparticles were innovatively decorated by carbon bridge onto the amino-group functioned Zr-terephthalate metal-organic framework (MOF) UiO-66 to reduce the diffusion energy barrier and then improve the hydrogen spillover effect. Powder X-ray diffraction shows broad Pd peak and retained UiO-66-NH2 integrity after Pd decoration. The hydrogen uptake capacity show that UiO-66-NH2-Pd exhibits best hydrogen storage performance than UiO-66-NH2 and pristine UiO-66. The hydrogen up taken in Pd decorated UiO-66 (UiO-66-NH2-1Pd) was close to 4 wt% under 20 MPa at room temperature. Density functional theory (DFT) calculations show that hydrogen adsorption energy of UiO-66-NH2-Pd was −0.5897 eV, which was much lower than that of UiO-66-NH2 (−0.3716 eV) and UiO-66 (−0.2975 eV). Ultimately, Pd decorated NH2 group functioned UiO-66 enable improve storage capacities through hydrogen spillover under ambient conditions which could satisfy the demand for sustainable energy, especially for the long-term storage energy media.

Nanoencapsulated MgBu2@ZIF-67 to Construct High Loading Mg-Co@C Nanocomposites: Breaking Through the Barrier of Room Temperature Onset Dehydrogenation.

The synergies of nanoconfinement and catalysis is an effective strategy to improve the kinetic and thermodynamic properties of Mg-based materials. However, obtaining Mg-based materials with high loading, anti-aggregation, and containing nanocatalysts to achieve dehydrogenation at room temperature remains a huge challenge. Herein, a novel and universal preparation strategy for Mg-Co@C nanocomposites with 9.5nm Mg nanoparticles and 9.4nm Co nanocatalysts embedded in carbon scaffold is reported. The 9.3nm MgBu2 nanosheets precipitated by solvent displacement are encapsulated in ZIF-67 to prepare MgBu2@ZIF-67 precursors, then removing excess MgBu2 on the precursor surface and pyrolysis to obtain Mg-Co@C. It is worth noting that the Mg loading rate of Mg-Co@C is as high as rare 69.7%. Excitingly, the Mg-Co@C begins to dehydrogenate at room temperature with saturate capacity of 5.1wt.%. Meanwhile, its dehydrogenation activation energy (Ea(des) = 68.8kJ mol-1) and enthalpy (ΔH(des) = 61.6kJ mol-1) significantly decrease compared to bulk Mg. First principles calculations indicate that the hydrogen adsorption energy on the Mg2CoH5 surface is only -0.681eV. This work provides a universally applicable novel method for the preparation of nanoscale Mg-based materials with various nanocatalysts added, and provides new ideas for Mg-based materials to achieve room temperature hydrogen storage.

Hydrogen adsorption, migration and desorption on amorphous carbon: A DFT and AIMD study

Physisorption is the general dominating adsorption mode on pure carbonaceous materials. In this study, we examined if chemisorbed hydrogen can be accomplished without incorporating metals on carbon surfaces. We constructed two 100-atom amorphous carbon (a-C) models with different microenvironments (42 % 2-fold, 52 % 3-fold, and 6 % 4-fold coordinated carbon atoms and 18 % 2-fold and 82 % 3-fold, respectively) using ab initio molecular dynamics (AIMD) simulations to mimic activated carbon samples in reality. The structural, energetic, electronic structure and kinetic properties of hydrogen adsorption, migration, and desorption on the a-C surfaces were analyzed using density functional theory (DFT) and AIMD calculations, which showed that: (1) hydrogen molecules could spontaneously dissociate on the convex side of 2-fold coordinated carbon atoms. Physisorption of hydrogen molecules mainly took place on 3-fold coordinated carbon atoms. (2) Regarding the multiple hydrogen adsorption, the entire a-C model could uptake around 156 hydrogen atoms with the adsorption energy per hydrogen atom about −0.70 to −0.60 eV at high hydrogen pressure. In addition, we found that the average individual adsorption energy of a single hydrogen atom on different carbon atoms could be used as a quick prediction for the saturated hydrogen adsorption energy. (3) The migration barrier of a hydrogen atom between two adjacent carbon atoms was about 2 eV at both low and high hydrogen coverage, indicating that hydrogen mobility on this designed a-C model was low. The desorption of a hydrogen molecule can take place at 300 K using AIMD calculation, but not for atomic hydrogen desorption. In this work, we demonstrated that hydrogen chemisorption could take place on this designed a-C without the decoration of metal particles to enhance hydrogen adsorption amounts. The materials design to balance hydrogen chemisorption, migration, and desorption shall be considered in the future.

Hydrogen storage on MgO supported TiMgn (n = 2–6) clusters: A first principle investigation

The current study explores the potential of MgO-supported finite-sized TiMgn (n = 2–6) nanoclusters as hydrogen storage materials, employing density functional theory with a spin-polarized generalized gradient approximation (GGA). These systems' structural stability and electronic characteristics reveal that supported clusters offer superior hydrogen storage capabilities compared to their unassisted counterparts. Various parameters, including cluster-adsorption energy (Eads), hydrogen-adsorption energy in supported clusters (Eads-H), HOMO-LUMO gap, vertical ionization potential (VIP), vertical electron affinity (VEA), chemical potential (μ), and chemical hardness (ɳ) are computed. Substrate support notably enhances the thermodynamic stability and chemical reactivity of the TiMg5 cluster when contrasted with the bare TiMg5 cluster. Furthermore, a remarkable increase in the gravimetric hydrogen storage density, from 1.63 wt% for bare Mg5 clusters to 3.45 wt% for bare TiMg5 clusters, reaching 5.62 wt% in the supported TiMg5 cluster system is observed. These findings indicate the substrate-supported TiMg5 cluster as a promising candidate for hydrogen storage applications.

Hydrogen Adsorption on Ordered and Disordered Pt-Fe and Pt-Co Alloys.

The bulk properties and surface chemical reactivity of compositionally disordered Pt-Fe and Pt-Co alloys in the fcc A1 phase have been investigated theoretically in comparison to the ordered alloys of the same compositions. The results are analyzed together with our previously reported findings for Pt-Ni. Nonlinear variation is observed in lattice constant, d band center, magnetic moment, and hydrogen adsorption energy across the composition range (0-100 atomic % of Pt, x Pt). The Pt 5d states are strongly perturbed by the 3d states of the base metals, leading to notable density of states above the Fermi level and residual magnetic moments at high x Pt. Surface reactivity in terms of average H adsorption energy varies continuously with composition between the monometallic Fe-Pt and Co-Pt limits, going through a maximum around x Pt = 0.5-0.75. Close inspection reveals a significant variation in site reactivity at x Pt < 0.75, particularly with disordered Pt-Fe alloys due in part to the inherent disparity in chemical reactivity between Fe and Pt. Furthermore, the strong interaction between Fe and Pt causes Pt-rich sites to be less reactive toward H than Pt-rich sites on disordered Pt-Ni alloy surfaces, despite less compressive strain caused. These results provide theoretical underpinnings for conceptualizing and understanding the performance of these Pt-base metal alloys in key catalytic applications and for efforts to tailor Pt-alloys as catalysts.

Cation vacancy modulated Cu3P-CoP heterostructure electrocatalyst for boosting hydrogen evolution at high current densities and coupling Zn-H2O battery

Exploiting highly efficient, cost-effective and stable electrocatalysts is key to decreasing hydrogen evolution reaction (HER) kinetics energy barrier. Herein, the alkaline HER kinetics energy barrier can greatly reduce by the joint strategies of the cation vacancy and heterostructure engineering, which is seldom explored and remains ambiguous. In this study, an efficient and stable copper foam-supported Cu3P-CoP heterostructure electrocatalyst with cation vacancy defects (defined as Cu3P-CoP-VAl/CF) was designed for HER via the successive coprecipitation, electrodeposition, alkali etching and phosphorization treatments. As anticipated, the as-obtained Cu3P-CoP-VAl/CF electrocatalyst reveals a remarkable catalytic activity for HER with a low overpotential of 205 mV at a current density of 100 mA·cm−2, a high turnover frequency value of 1.05 s−1 at an overpotential of 200 mV and a small apparent activation energy (Ea) of 9 kJ·mol−1, while shows superior long-term stability at large current densities of 100 and 240 mA·cm−2. Systematic experiment and characterization data demonstrate that the formed cation vacancy could optimize the Ea, leading to the decrease of the kinetic barriers of Cu3P-CoP/CF heterostructure, as well as the established heterogeneous interface induced a synergistic effect between biphasic components on boosting the kinetics toward HER. The results of density functional theory disclose that the synergistic effect of Cu3P-CoP heterostructure could decrease the energy barrier and optimize Gibbs free energy of hydrogen adsorption, resulting in the enhancement of intrinsic catalytic activity of Cu3P-CoP-VAl/CF. More significantly, the alkali-cell assembled by Cu3P-CoP-VAl/CF (cathode) and RuO2/CF (anode) behaves outstanding water splitting performance, delivering a current density of 10 mA·cm−2 at a relatively small applied voltage of 1.58 V, along with encouraging long-term durability. In addition, the alkaline Zn-H2O battery with Cu3P-CoP-VAl/CF as the cathode has been fabricated for the simultaneous generation of electricity and hydrogen, which displays a large power density of up to 4.1 mW·cm−2. The work demonstrates that rational strategy for the design of competent electrocatalysts can effectively accelerate the kinetics of HER, which supplies valuable insights for practical applications in overall water splitting.

Discovery of Self-Assembled 2D Ru/Si Superlattices Boosting Hydrogen Evolution.

2D heterostructuring is a versatile methodology for designing nanoarchitecture catalytic systems that allow for reconstruction and modulation of interfaces and electronic structures. However, catalysts with such structures are extremely scarce due to limited synthetic strategies. Here, a highly ordered 2D Ru/Si/Ru/Si… nano-heterostructures (RSHS) is reported by acid etching of the LaRuSi electride. RSHS shows a superior electrocatalytic activity for hydrogen evolution with an overpotential of 14mV at 10mA cm-2 in alkaline media. Both experimental analyses and first-principles calculations demonstrate that the electronic states of Ru can be tuned by strong interactions of the interfacial Ru-Si, leading to an optimized hydrogen adsorption energy. Moreover, due to the synergistic effect of Ru and Si, the energy barrier of water dissociation is significantly reduced. The well-organized superlattice structure will provide a paradigm for construction of efficient catalysts with tunable electronic states and dual active sites.

Enhanced acidic hydrogen evolution reaction kinetics via nitrogen-doped iridium nanosheet with optimized hydrogen adsorption energy

The hydrogen evolution reaction (HER) is influenced by the adsorption/desorption of hydrogen intermediates on active sites. Nitrogen doping is a way to alter the electronic structure and boost the activity of metal electrocatalysts although the mechanism remains controversial. Here, nitrogen is incorporated into face-centered cubic iridium nanosheets (N-fcc-Ir-NSs) through the ammonia reduction of metastable two-dimensional pristine trigonal iridium oxide. With a nitrogen content of only 0.8 wt%, N-fcc-Ir-NSs exhibit a low overpotential of 19 mV at −10 mA cmgeo-2 and a Tafel slope of 18.6 mV dec-1 in sulfuric acid. The doped nitrogen reduces hydrogen adsorption energy by modulating the electronic structure of iridium atoms, and the combined effects of iridium sites with strong hydrogen adsorption energy and iridium sites near the nitrogen atoms with weak hydrogen adsorption energy improve the HER activity. Moreover, the presence of nitrogen causes iridium to donate more electrons to hydrogen and promotes hydrogen desorption.

Coordinated Adsorption/Desorption Kinetics Enabled by Surface Sulfur Decoration Over Mo2C for Boosted Hydrogen Evolution Reaction

AbstractMaintaining a consistently high current density growth rate in the hydrogen evolution reaction is highly challenging because the limited mass transfer rate at the electrode/electrolyte interface will make the adsorption reaction as the rate‐determining step associated with a low hydrogen coverage, exhibiting a Tafel slope &gt;120 mV dec–1. Therefore, maximizing the current density range in which the desorption reaction is the rate‐determining step, can significantly reduce the overpotential. Herein, a surface sulfur decoration strategy is presented to modify the molybdenum carbide electrocatalyst and achieve coordinated adsorption/desorption kinetics, leading to a dominant Volmer–Heyrovsky mechanism across a wide range of current densities. Both experimental and theoretical results validate the surface charge redistribution induced by sulfur decoration, which subtly optimizes the Gibbs free energy of hydrogen adsorption and enhances the in‐plane polarization field. As a result, the as‐obtained surface sulfur‐decorated molybdenum carbide electrocatalyst exhibits coordinated adsorption/desorption kinetics and efficient hydrogen delivery, ultimately surpassing the commercial Pt/C electrocatalyst for high‐efficiency hydrogen evolution.

RuMo nanoalloy confined on N-doped carbon toward efficient alkaline and acidic hydrogen evolution reaction

Noble metal-based electrocatalysts have been demonstrated significant efficiency in the production of hydrogen. However, the sluggish kinetics of the hydrogen evolution reaction (HER) in alkaline media due to high water dissociation energy greatly hinders this electrochemical process. Here, we report a RuMo nanoalloy electrocatalyst mounted on a nitrogen-doped carbon skeleton (RuMo@NC). The RuMo@NC catalyst exhibits excellent HER performance in both alkaline and acidic media, displaying small overpotentials of 18 mV and 14 mV for driving the current density of 10 mA⊡cm−2, respectively. This performance surpasses the majority of noble metal electrocatalysts and 20 % commercial Pt/C. Theoretical calculations reveal that the interaction between Ru and Mo results in a modification of the electronic structure. Consequently, this interaction effectively weakens the adsorption energy of hydrogen on the surface of the RuMo alloy, ultimately improving its catalytic performance in the hydrogen evolution reaction. This work offers new ways to design efficient and economical HER electrocatalysts, advancing the exploration of HER catalysts.

Recent progress of molybdenum disulfide/carbon composites for electrochemical hydrogen evolution reaction

As a star two-dimensional material, molybdenum disulfide (MoS2) shows a good potential in the field of electrochemical hydrogen evolution reaction (HER) due to its low price, special physicochemical properties and a small theoretical Gibbs free energy of hydrogen adsorption. However, some disadvantages such as poor electroconductivity and inert basal planes hinder its further improvement of HER activity. Therefore, adopting carbon materials with good electrical conductivity and large specific surface area to composite with MoS2 is one of the popular strategies to improve the electrical conductivity and increase the exposure of catalytically active sites for constructing highly efficient MoS2-based electrocatalysts. Herein, in this review, we firstly gave a brief introduction of the MoS2 structure and the basic HER principle. Then, the synthesis method, catalytic performance and reaction mechanism of utilizing different carbon materials to improve the HER activity of MoS2 were summarized in detail. Finally, the existing problems and future opportunities for preparing highly active and low cost electrocatalysts assisted by carbon materials are prospected.

Stabilizing and Activating Active Sites: 1T-MoS2 Supported Pd Single Atoms for Efficient Hydrogen Evolution Reaction.

Metallic 1T-MoS2 with high intrinsic electronic conductivity performs Pt-like catalytic activity for hydrogen evolution reaction (HER). However, obtaining pure 1T-MoS2 is challenging due to its high formation energy and metastable properties. Herein, an in situ SO4 2--anchoring strategy is reported to synthesize a thin layer of 1T-MoS2 loaded on commercial carbon. Single Pd atoms, constituting a substantial loading of 7.2wt%, are then immobilized on the 1T-phase MoS2 via Pd─S bonds to modulate the electronic structure and ensure a stable active phase. The resulting Pd1/1T-MoS2/C catalyst exhibits superior HER performance, featuring a low overpotential of 53mV at the current density of 10mAcm-2, a small Tafel slope of 37mVdec-1, and minimal charge transfer resistance in alkaline electrolyte. Moreover, the catalyst also demonstrates efficacy in acid and neutral electrolytes. Atomic structural characterization and theoretical calculations reveal that the high activity of Pd1/1T-MoS2/C is attributed to the near-zero hydrogen adsorption energy of the activated sulfur sites on the two adjacent shells of atomic Pd.

Structural optimization and electrocatalytic hydrogen production performance of carbon-based composites: A mini-review

The energy demand has increased significantly in recent years and it is urgent to develop a renewable energy system that is highly efficient and non-noble metal-based. Hydrogen energy is an environmentally friendly energy source with abundant resources, which can be used to solve the problem of high energy demand without greenhouse gas emissions. However, the development of catalysts for hydrogen production technology by electrolysis of water is slow, mainly due to the complexity of the electrolysis hydrogen generation process, low hydrogen production efficiency, weak electrode material activity and high cost. Among the non-noble metal-based catalysts, carbon-based materials have high conductivity, tunable chemical bonding, and easily modified morphology, making them beneficial to achieving efficient hydrogen production, though pure carbon composites suffer from few surface-active sites and unmoderated hydrogen bonding energy, which need to be further optimized. The principle of electrocatalytic hydrogen production from the perspectives of reaction thermodynamics and kinetics is analyzed and discussed in this paper. Thermodynamics of electrocatalytic hydrogen production is reflected by the Gibbs free energy of hydrogen adsorption (ΔGH*) and electrode potential (E). Reaction kinetics of the electrocatalytic hydrogen production process are reflected by overpotential, Tafel slope and exchange current density. Structural optimization methods of carbon-based composite materials and hydrogen production performance after structural optimization are also summarized. Structural optimization methods of carbon-based composite materials mainly include introducing active sites, improving conductivity, increasing specific surface area and introducing self-supporting materials. Finally, prospects are proposed for the development direction and existing problems of electrocatalytic hydrogen production performance of carbon-based composites.