High Intensity Heavy-ion Accelerator Facility Research Articles

Conceptual design and simulated performance of the Barrel part of gamma array for the experimental terminal at HFRS of HIAF

The Barrel of γ array, consisting of 640 CsI(Tl) crystals and covering a polar angle range from 36.4° to 135.6°, has been designed for the experimental terminals at High energy FRagment Separator of High-Intensity heavy-ion Accelerator Facility in Huizhou. Together with the existing Endcap, consisting of 1024 CsI(Tl) crystals and covering a polar angle from 15.6° to 36.4°, at the External Target Facility in Lanzhou to form a new γ array, it is expected to meet the experimental requirements for in-beam γ-ray spectroscopy technique. A Monte Carlo code based on Geant4 was implemented to study the performance of the new γ array. Taking into account the Doppler correction and the intrinsic energy resolution of the detector, the energy resolution is 5.4% (FWHM) for the Endcap and 9.8% (FWHM) for the Barrel when the energy of the emitted γ-ray is 1 MeV in the Center-of-Mass frame with the beam energy of 500 MeV/u (beam velocity β = 0.759). The full-space photopeak efficiency is greater than 40% when the energy of the emitted γ-ray is less than 5 MeV in the Center-of-Mass frame and the beam energy is less than 700 MeV/u (β = 0.821). Such performance can satisfy most of the physics requirements for in-beam γ-ray spectroscopy experiments.

Design and Implementation of Chopper Control System for HIAF

The chopper control system which is synchronized by the White Rabbit timing network is designed and implemented to meet the requirements of the chopper of ion source for the High-Intensity Heavy Ion Accelerator Facility (HIAF). The hardware system consists of timing modulation controller, waveform acquisition, parameter setting, and remote control of the chopper power supply. The software includes low-level drivers and top-level applications which are based on Experimental Physics and Industrial Control System (EPICS). The combination of hardware and software completes the interaction of timing messages with the White Rabbit network, waveform acquisition, the setting of timing modulation parameters in several running modes, and remote control of the chopper power supply, etc. The test results show that the system can achieve timing modulation with a resolution of 8 ns and waveform acquisition of embedded EPICS IOC (input/output controller) at a 125 MHz sample rate. The design, implementation, and test of the chopper control system are described in this paper.

Design and Implementation of Chopper Control System for HIAF

The chopper control system which is synchronized by the White Rabbit timing network is designed and implemented to meet the requirements of the chopper of ion source for the High-Intensity Heavy Ion Accelerator Facility (HIAF). The hardware system consists of timing modulation controller, waveform acquisition, parameter setting, and remote control of the chopper power supply. The software includes low-level drivers and top-level applications which are based on Experimental Physics and Industrial Control System (EPICS). The combination of hardware and software completes the interaction of timing messages with the White Rabbit network, waveform acquisition, the setting of timing modulation parameters in several running modes, and remote control of the chopper power supply, etc. The test results show that the system can achieve timing modulation with a resolution of 8 ns and waveform acquisition of embedded EPICS IOC (input/output controller) at a 125 MHz sample rate. The design, implementation, and test of the chopper control system are described in this paper.

Ion-optical updates and performance analysis of High energy FRagment Separator (HFRS) at HIAF

The High energy FRagment Separator (HFRS), a new generation in-flight radioactive separator, is under construction at the high-intensity Heavy Ion Accelerator Facility (HIAF) in China. To further optimize the separator performance and consider the manufacturing technology, the specifications of some magnetic elements of the HFRS separator have been modified from the original design reported earlier, and prototypes of partial magnetic elements have been fabricated and tested. In this paper, updates of magnetic parameters, test results of prototypes, and development of ion-optical calculation are presented. The high-order correction of aberrations is demonstrated. The performance of the separator is studied using fission reactions and fragmentation reactions of relativistic 238U projectiles. This work will guide the forthcoming experiments in the future HFRS separator.

The HSPC — a high speed PCIe readout card for the HFRS-TPC

A new High-Speed PCI Express (PCIe) readout Card (HSPC) has been designed to transmit and aggregate data from the Time Projection Chamber (TPC) that will be assembled on High energy FRagment Separator (HFRS) beamlines at the High Intensity heavy-ion Accelerator Facility (HIAF) currently being built in Huizhou City, China. The HSPC features a high-performance controller utilizing the Xilinx Kintex Ultrascale Series Field Programmable Gate Array (FPGA), two Quad Small Form-factor Pluggable Plus (QSFP+) connectors, and a PCIe Gen3×8 interface with theoretical bandwidth of 64 Gbps. Experimental testing shows that there are no errors on the 8-fiber optics when operating at 9.6 Gbps per link, and the bit error rate (BER) is less than 1.0 × 10-15. In addition, the total read bandwidth of PCIe Gen3×8 reaches 7085.4 MB/s. Consequently, the HSPC can meet HFRS requirements.

Study on the performance of titanium alloy-lined thin-walled vacuum chamber

HIAF-BRing, the main synchrotron accelerator of the High Intensity Heavy-Ion Accelerator Facility, requires an average pressure lower than 1 × 10 −9 Pa and the magnetic field increase rate of no less than 12 T/s to fulfill radioactive beam physics and high energy density physics experiments. To reduce the eddy current effect and the gap size of dipoles, a titanium alloy-lined thin-walled vacuum chamber with a wall thickness of 0.3 mm is proposed by IMP, which has been developed from the initial ceramic-lined vacuum chamber. By mechanical loading testing, when the internal stress of titanium alloy rings made by 3D selective laser melting (SLM) reaches 639 MPa, it is still within the elastic deformation range, in fact, the yield strength of the 3D printed titanium alloy material is 912 MPa. In order to reduce the pressure gradient inside the thin-walled vacuum chamber caused by the surface outgassing of the rings, TiZrV thin films have been deposited on the rings by planar target magnetron sputtering. Through TiZrV deposited on the rings, the pressure at the middle of the thin-walled vacuum chamber has been dropped from 1.5 × 10−9 Pa to 1.0 × 10−9 Pa. At the same time, as the magnets are continuously energized, the actual heating state of the thin-walled vacuum chamber has been also measured.

Cryogenic distribution system design for cryomodules and cavities test in HIAF project

ABSTRACT High-intensity heavy-ion accelerator facility (HIAF) is an accelerator-driven high-current heavy ion facility, currently under construction in Guangdong, China. The proton linear accelerator of HIAF linac has 96 superconducting cavities and 17 cryomodules cooled by 2 K saturated superfluid helium. Cryogenic tests should be carried out in a test cryogenic system prior to the online operation of each cavity and cryomodule. The cryogenic distribution system (CDS) is the main part of the test cryogenic system, which is used for transporting cryogenic fluid between helium refrigerator and test terminals. A specific CDS is developed due to the long cryogenic test time. Each test terminal can be independently cooled and heated up, saving quite a bit of time without impacting the others. This article provides comprehensive explanations for the process design, process analysis, and special structure design which enhance the system’s maintainability. Furthermore, particular technical designs, such as measuring system, helium guard, and elimination of thermoacoustic oscillations, are described in detail.

Design and characterization of multichannel front-end electronics for detectors at HIRFL and HIAF

A multichannel front-end readout electronics (MFEE) has been designed for readout in detectors in the heavy ion facility in Lanzhou (HIRFL) and the high-intensity heavy-ion accelerator facility (HIAF). With 40 different adjustable gains, this MFEE can meet the need for most of the experiment. One MFEE can read and process the output signals of 128 channels of a detector at the same time. MFEE is based on the AD8488 chip and uses Xilinx Kintex 7 series FPGA, combined with the periphery circuits design, to complete the detector's output charge signal readout. This paper will discuss the design and performance of the MFEE.

Design of Nupix-A2, a Monolithic Active Pixel Sensor for heavy-ion physics

The High Intensity heavy-ion Accelerator Facility (HIAF) is being constructed to generate intense beams of primary and radioactive ion for a wide range of research fields. Hence, a Monolithic Active Pixel Sensor (MAPS) named Nupix-A2 has been developed in a 130-nm High Resistivity CMOS process. The Nupix-A2 can simultaneously measure the particle hit' energy, arrival time, and position. It consists of a 128 × 128 pixel array, a digital-to-analog converter array, and a digital control module. The Nupix-A2 can measure energy deposition from 300 e- to over 50 ke- and time duration from 13 μs to 140 μs. This sensor also offers full readout mode and fast readout mode. In full-readout mode, all pixels measure arrival time and energy, suitable for real-time beam monitoring and image reconstruction. In fast-readout mode, only particle hit's positions are detected and read out. This paper presents the design of the Nupix-A2.

Measurement and optimization of the beam coupling impedance of a novel 3D-printed titanium alloy cage inside the thin-wall vacuum chamber.

Dipole magnet vacuum chambers are among the most critical and costly components of rapid-cycling accelerator facilities. Alternative approaches to traditional ceramic chambers have been explored for the implementation of fast-ramping dipole-magnet vacuum chambers, including thin-wall metallic beam pipe chambers strengthened with transverse ribs and ceramic rings inside thin-walled chambers. Here, we report a novel 3D-printed titanium alloy cage inside the thin-wall vacuum chamber, which is designed for high-intensity heavy ion accelerator facility (HIAF) to reduce manufacturing difficulty and cost, shorten the production cycle, and improve the quality. Comprehensive studies were undertaken to characterize the impedance of the 3D-printed titanium alloy cage inside the thin-wall vacuum chamber. The beam-coupling impedance and eddy currents of the new thin-wall vacuum chamber were studied mostly numerically. Strategies for further reducing the beam-coupling impedance were explored. In addition, impedance bench measurements using the "half wavelength" resonant method were conducted to identify the longitudinal and transverse impedances of the 3D-printed titanium alloy cage inside the thin-wall vacuum chamber prototype experimentally. The simulated and measured results for the impedance were consistent. Furthermore, a campaign for resonance-check measurements on the 3D-printed titanium alloy ring loaded inside a thin-wall vacuum chamber prototype was launched. This novel thin-wall vacuum chamber structure is now entering the fabrication stage and will soon be ready for installation in the Booster Ring (BRing).

Stochastic cooling notch filter developments for the high-precision spectrometer ring in the high intensity heavy-ion accelerator facility project.

Stochastic cooling of the high-precision spectrometer ring (SRing) at the High Intensity Heavy-Ion Accelerator Facility (HIAF) project in China, which is used mainly for experiments with radioactive fragment beams, is applied to speed up the cooling process of a stored ion beam. In this article, a new coaxial-type notch filter with an amplitude equalizer in the long branch and an optical-type notch filter with phase-stabilized optical fiber are discussed and evaluated for the SRing stochastic cooling system. Both prototypes of coaxial and optical notch filters are fabricated and tested. The minimum notch depth of coaxial and optical notch filters reaches to 26 and 40 dB, respectively. The performance of both coaxial notch filter and optical fiber notch filter is presented in this work. These developments will be used not only for the longitudinal stochastic cooling system but also have potential for the beam feedback system.

Research on the newest GaN-Based solid-state power amplifier for CiADS project

Institute of Modern Physics (IMP), Chinese Academy of Sciences is the first domestic institute to widely apply solid-state power amplifier (SSPA) to linear accelerator project from China Accelerator Driven Sub-critical System (C-ADS) project started since 2011. Until now, SSPA design has already been considered for two large-scale scientific facilities in Guangdong Province of southeast China: China initiative Accelerator Driven System (CiADS) and High Intensity Heavy-ion Accelerator Facility (HIAF). The SSPA was developed rapidly due to the reliable technologies of LDMOS-based (laterally diffused metal oxide semiconductor) power amplifiers.With the maturation of GaN (Gallium Nitride) technology, GaN-based amplifiers have been studied in the field of accelerators since 2020. Last year, IMP made new progress with GaN SSPA, measuring power modules at three fundamental frequency points of 162.5 MHz, 325 MHz, and 650 MHz. The first 50 kW rack with GaN SSPA was measured at 650 MHz in IMP, and its modules offer huge advantages of 40% output power and 8% efficiency compared to the newest LDMOS at the same frequency, which holds a fascination for our project.Until the beginning of 2023, the prototype power modules on three frequency points were completed and tested. This paper will detail the design development of GaN technology and its technical characteristics.

A Full-Waveform Digitizer for the Readout of Plastic Scintillator Detectors at HIRFL and HIAF

Being among the world’s leading heavy-ion scientific facilities, the heavy ion research facility in Lanzhou (HIRFL) and the high-intensity heavy-ion accelerator facility (HIAF) are constructed to study nuclear physics, atomic physics, nuclide chart, and heavy-ion related applications. Plastic scintillator detectors (PSD) are highly desirable and are used in large amounts for performing the experiments at HIRFL and HIAF. The PSDs are coupled with a photomultiplier tube (PMT) or silicon photomultiplier (SiPM) for converting the photons into electric signals. In this work, we develop a 16-channel full waveform digitizer (FWD) as a standard readout unit for the PSDs at HIRFL and HIAF. The FWD is based on two DRS4 chips. The design of these chips is based on the principle of a switched capacitor array (SCA), which can sample the analog signals at the GHz scale with low power consumption. In addition, the proposed FWD is designed with a general-purpose technique to reduce the development time, production cost, and maintenance difficulties. The laboratory test results show that the proposed FWD is relatively less nonlinear, i.e., about 0.6%. Its time precision is better than 15 ps. The cascade of multiple channels successfully realizes a sampling depth of 2048 cells. The joint test results of PSD show that an excellent performance in terms of measuring the cosmic rays is achieved. This paper presents the design and performance of the proposed FWD.

Design and Simulation of HiGBt, a 5 Gb/s SerDes for Heavy-Ion Physics Experiments

The Heavy Ion Research Facility on Lanzhou (HIRFL) and the High-Intensity heavy-ion Accelerator Facility (HIAF) are the leading heavy-ion physics centers. The increased scale of physics experiments at HIRFL and HIAF has put forward urgent requirements on high-speed serial data transmission links. Also, the intense radiation environment is a significant challenge to commercial ASIC. This paper presents the HiGBt, a general-purpose 5 Gbps SerDes ASIC designed in a 0.13 μm CMOS process for data transmission at HIRFL and HIAF. The HiGBt mainly consists of a Serializer, a Deserializer, and a high-speed clock system. The Serializer includes three stages to realize high-speed serialization. The Deserializer adopts a high linearity phase-interpolator-based structure to avoid coupling multi-VCOs. Finally, the high-speed clock system has a Single Event Upsets (SEUs)-protected divider. The simulation results indicate that the power consumption of the SerDes is 146.3 mW, while the layout area is 310 μm × 310 μm.

Design of an SHA-Less Pipeline ADC With Op-Amp Sharing Techniques for MAPS

As the leading research platform of heavy-ion science in China, the heavy-ion physics and applications at the Heavy Ion Research Facility in Lanzhou (HIRFL) and the High-Intensity heavy-ion Accelerator Facility (HIAF) drive the development of new detector technology. A monolithic active pixel sensor (MAPS) has been designed in a 130-nm CMOS process for HIRLF and HIAF. This MAPS can measure the energy deposition and position of the particle hit. As the critical component of this MAPS, a regional 12-bit 40-Msps pipeline ADC has been designed to convert the analog signals from the pixels into digital data. Due to the strict limitation on power and area, this ADC adopts the SHA-less architecture and stepwise capacitance reduction. Also, the op-amp sharing technology is used in the 1.5-bit stages. This ADC has a power consumption of 60 mW and occupies <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$874\times 550\,\,\mu \text{m}$ </tex-math></inline-formula> . Simulation results indicate that it achieves an ENOB of 11.77 bits and a SINAD of 72.57 dB at the tt corner with an input frequency of 3.291 MHz. The figure of merits (FOM) value is 507 fJ/step.

Low beta superconducting cavity system design for HIAF iLinac

A superconducting ion-Linac (iLinac), which is supposed to work as the injector in the High Intensity heavy-ion Accelerator Facility project, is under development at the Institute of Modern Physics (IMP), Chinese Academy of Sciences. The iLinac is a superconducting heavy ion linear accelerator approximately 100 meters long and contains 96 superconducting cavities in two types of 17 cyromodules. Two types of superconducting resonators (quarter-wave resonators with a frequency of 81.25 MHz and an optimal beta β = v/c = 0.07 called QWR007 and half-wave resonators with a frequency of 162.5 MHz and an optimal beta β = 0.15 called HWR015) have been investigated. The cavity design included extensive multi-parameter electromagnetic simulations and mechanical analysis，and its results are described in details. The fundamental power coupler and cavity dynamic tuner designs are also presented in this article. The prototypes are under manufacturing and expected to be ready in 2023.

Accurate Low Current Measurement Electronics With Self-Calibration Function for Ionization Chamber of Slow Extraction in HIAF

The new wide-range readout electronics with a self-calibration function are designed for ionization chambers (ICs) in the slow extraction of high-intensity heavy-ion accelerator facility (HIAF), booster ring (BRing). These electronics consist of a programmable trans-impedance amplifier (TIA), a self-calibration circuit, an 18-bit analog-to-digital converter (ADC), and a ZYNQ-7015 field-programmable gate array (FPGA). It is capable of monitoring weak current signals of 40 pA–4 mA with a sampling rate of 5 MHz. The ZYNQ-7015 FPGA manages the operation mode of the analog front-end (AFE) and the gain of the TIA. It also performs digital signal processing algorithms and data communication with the host computer. The self-calibration circuit uses a combination of a Schmitt trigger and voltage-to-current (V–I) converters to generate two square wave current signals with different peaks ( <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">$2 \mu \text{A}$ </tex-math></inline-formula> and 2 mA). During offline tests, the effective number of bits (ENOB) is 12.98 bits, and the nonlinearity is less than 0.075% for a full scale. Finally, the readout electronics are deployed for ICs’ slow extraction measurements at the extraction line of the cooling storage ring of the heavy-ion research facility in Lanzhou (HIRFL). With the help of a commercial dc-transformer in the cooling storage ring project of heavy ion research facility in Lanzhou (HIRFL-CSR), these electronics not only execute an accurate current measurement, but also can monitor the extraction efficiency reliably. In a word, these electronics play an important role in the fields of extremely weak and high dynamic current signal measurements.

Study on baking deformation of the thin-walled arc chamber

A large scientific facility, High Intensity heavy-ion Accelerator Facility (HIAF), was being built to study basic and interdisciplinary sciences. To meet the requirements of magnetic rigidity for high-energy heavy ions, pulsed dipole magnets were used in Booster Ring (BRing). Therefore, the ceramic-lined thin-walled arc chambers with 0.3 mm shell were developed to reduce the eddy current resulting from the rapidly changing magnetic field. Furthermore, to satisfy the requirements of the beam lifetime, the pressure of BRing of the HIAF must be lower than 1 × 10−9 Pa. In-situ baking methods were used to obtain ultra-high vacuum. As the stiffness of the thin-walled arc chamber was poorer for evacuation and in-situ baking as a conventional way, it had to be controlled in the deformation and deflection angle. Thus, a deformation control method using springs was adopted. The results show that the longitudinal deformation of both different thin-walled chambers was controlled to within 0.3 mm, the radial deformation was controlled to within 0.8 mm and the variation of deflection angle was within 0.2°.

Eddy current and structural analysis of the beam pipe for the BRing dipole magnet

Fast-ramping magnets will be used in the Booster Ring (BRing) of the High-Intensity Heavy Ion Accelerator Facility (HIAF), which is proposed by the Institute of Modern Physics (IMP), Chinese Academy of Sciences (CAS). The dipole magnet will provide the field quality from the injection field of 0.0496 T up to the maximum value of 1.5786 T, with the maximum ramping rate of 12 T/s. The ramping magnetic field induces eddy currents that give rise to eddy loss and large force on the beam pipe, field delay and sextupole field appear to affect the field quality provided by the BRing dipole. An in-detail understanding of these effects is an essential aspect of the design. Based on the finite-element analysis, a simplified model by use uniform background magnetic field was used to the transient simulations, eddy current and the forces on the pipe at different times on the beam pipe were performed. This paper presents the results obtained for the eddy loss and magnetic field delay for different wall thicknesses. Then, mechanical design details are presented, and also stress distribution, the deformation in the beam pipe. The analysis results revealed that the eddy current and thus the field delay and eddy current-induced Lorentz force scales linearly with the derivative of the magnetic field and the thickness of the pipe. The power losses that cause heating of the pipe is linear with the square of the derivative of the magnetic field and the thickness of the pipe.

Research on the layout of primary control network and new measurement method for the HIAF survey and alignment

HIAF (High Intensity heavy ion Accelerator Facility) is one of the major national science and technology infrastructure projects in the “12th Five-Year Plan” undertaken by the Institute of Modern Physics, CAS. The primary control network, as the basic framework of the local coordinate system control of the particle accelerator, is the basis for calculating the coordinates in the process of accelerator construction and implementation, and plays a very important role in the survey and alignment during the construction period and the maintenance and monitoring during the operation period. Based on the multi-dissimilar design structure of HIAF and the unique geological conditions of the construction area, a new high-density layout method of the primary control network and a high-precision 3D(three-dimensional) measurement method were studied, and were successfully applied to the survey and alignment of HIAF. Inside and outside the accelerator tunnel, a high-density 3D primary control network that can form a full envelope for the accelerator beam is respectively laid out. All primary control networks are embedded in the bedrock layer with stainless steel reference inner cylinder and outer protective cylinder, and special waterproof filling layer is set up. All primary control network points in the accelerator tunnel are equipped with measuring intervisible holes and measurement platforms that can directly perform 3D measurements on the ground. By setting up the laser tracker on the horizontal attitude of the measurement platform, the 3D coordinates of the primary control network points inside and outside the accelerator tunnel can be measured directly and with high precision, and the simultaneous adjustment of the measurement data can be completed. The HIAF primary control network layout and measurement method proposed in this paper overcomes the problems of heavy pile foundation, poor crack resistance and poor water seepage resistance of the primary control network laid by the traditional method and solves the problem that the traditional primary control network must separate the plane network and the elevation network for independent measurement. The traditional method of tunnel point and forced centering measurement is avoided. By using a laser tracker to directly measure the 3D coordinates of the primary control network points inside and outside the tunnel, the measurement efficiency and measurement accuracy of the primary control network are improved, and the reliability of primary control network measurements is increased. The feasibility and correctness of the HIAF primary control network layout and measurement method are verified by comparing the actual multi-system measurement results in the field. This method has a certain reference value for the layout of the primary control network of the same type of accelerator.