Graphite Furnace Atomic Absorption Research Articles

Metals distribution and investigation of L'vov platform surface using principal component analysis, multi-way principal component analysis, micro synchrotron radiation X-ray fluorescence spectrometry and scanning electron microscopy after the determination of Al in a milk slurry sample

This work describes the use of different strategies/techniques, such as scanning electron microscopy (SEM), multivariate analysis (principal component analysis (PCA) and multi-way PCA) and micro synchrotron radiation X-ray fluorescence (μSRXRF), in order to extract information about platform morphology, metals distribution on its surface, and the performance of conventional and permanent modifiers after slurry analyses using electrothermal atomic absorption spectrometry (ET AAS). With multivariate analysis it was possible to select Zr (500 μg for each 50 heating cycles) as a permanent chemical modifier for the determination of Al in milk powder slurry samples. Employing multi-way PCA and SEM, it was possible to note the differences in morphology between platforms permanently treated with Zr and those conventionally treated with Mg(NO 3) 2. The use of PCA and SEM also allowed finding similarities between new platforms, and those with and without Zr treatment. Using the μSRXRF it was possible to establish metals distribution on the L'vov platform and compare the performance of conventional [Mg(NO 3) 2] and permanent (Zr) modifiers.

Determination of total platinum in plasma and plasma ultrafiltrate, from subjects dosed with the platinum-containing N-(2-hydroxypropyl)methacrylamide copolymer AP5280, by use of graphite-furnace Zeeman atomic-absorption spectrometry.

AP5280 is an N-(2-hydroxypropyl)methacrylamide (HPMA) copolymer to which are linked tetrapeptide side chains containing bioactive platinum complexes at their C-terminal sides. We have developed and validated a rapid and sensitive analytical assay for the determination of total platinum concentrations in plasma, and free platinum of an AP5280 origin in plasma ultrafiltrate (PUF), of subjects dosed with AP5280. The total platinum levels were determined by use of graphite-furnace atomic-absorption spectrometry (GF-AAS) with Zeeman correction after appropriate dilution of the plasma sample with plasma-hydrochloric acid 0.2 mol L(-1) (1:5) as diluent. The limit of quantitation of this assay is 0.25 micromol L(-1) platinum in plasma. Linear calibration curves were obtained over the concentration range 0.25-5.0 micromol L(-1). Accuracy was between 87.7% and 104.2% and precision was 15.3% at the lowest concentration and less than 14% for all other levels tested. Accuracy and precision were thus in accordance with generally accepted criteria for analytical methods. Analysis of samples obtained from patients receiving AP5280 demonstrated the applicability of the described assay. Analysis of free platinum in PUF was performed by use of a previously validated and reported assay from our institute in which the same instrumental method is used.

Influência da geometria da plataforma na determinação de chumbo em zidovudina (AZT) por ET AAS

The aim of this work was to compare the performances of the L'vov and integrated platforms in order to overcome the interferences found on lead determination in zidovudine by ET AAS. Pyrolysis and atomization temperatures found with integrated platform were 700 and 1400°C, respectively. The characteristic masses were 12.7 ± 1.2 pg with integrated platform and 11.1 ± 1.3 pg with grooved platform. The ratio between the slopes of zidovudine and aqueous curves shows a decrease in the interferences when the L'vov platform is used (bAZT/baq = 0.97 ± 0.10) and the detection limit found was 0.03 µg.g-1. That ratio was 0.85 ± 0.07 with the integrated platform.

Speciation of Cr(III) and Cr(VI) in potable waters by using activated neutral alumina as collector and ET-AAS for determination.

The speciation of Cr(III) and Cr(VI) has been performed by using activated neutral alumina as adsorbent. Both species were quantitatively adsorbed on a small column filled with neutral alumina. The adsorbed Cr(III) was eluted with 4 mol L(-1) HNO(3) and Cr(VI) with 1.0 mol L(-1) ammonia solution. Recoveries of Cr(III) and Cr(VI) were 99% and 100%, respectively. Using ET-AAS for Cr determination the limit of detection in the sample was 0.01 microg L(-1). The combined procedure is fast and sensitive. It can be applied for routine analysis of water samples at sub-microg L(-1) levels with a relative standard deviation (RSD) of 2-10% (three determinations).

Speciation without chromatography : Part 2. Determination of tributyltin by chloride generation flow injection atomic absorption spectrometry

A procedure is described for the quantitation of tributyltin in aqueous samples and extracts based on its relatively high volatility in halide media, permitting vapour phase sampling from the headspace above such samples. Tributyltin chloride (TBT-Cl) was purged from various chloride containing aqueous matrices and collected on the surface of an iridium treated graphite tube for subsequent quantitation by graphite furnace atomic absorption. Iodide, bromide and chloride matrices were compared for their generation efficiency. The effect of acidity of the sample was also studied. An absolute detection limit of 1.3 ng TBT (as tin) was estimated, corresponding to a detection limit of 0.33 ng ml−1 for a 4 ml sub-sample. Method validation was achieved using NRCC PACS-2 (sediment) Certified Reference Material, for which reasonable agreement between certified and measured values of tributyltin content was obtained. A procedural concentration limit of detection of 66 ng g−1 TBT in the sediment could be achieved.

Determination of Urinary Beryllium, Arsenic, and Selenium in Steel Production Workers

Some of the most pernicious dangers of pollution arise from the presence of traces of toxic elements in the environment. In this work, we report on the determination of beryllium, arsenic, and selenium in the urine of steel production and steel quality control (QC) workers, in comparison to healthy control subjects. The urine samples were digested by a microwave system. Graphite furnace and hydride atomic absorption was used for the quantitative measurements of Be and As and Se, respectively. A quality control method for these procedures was established with concurrent analysis of Standard Trace Metals 7879 Level II and NIST SRM 2670 (Toxic Elements in Freeze Dried Urine). The results show that the urinary levels of these elements in steel production (As, 38.1 +/- 28.7 microg/L; Be, 1.58 +/- 0.46 microg/L, and Se, 69.2 +/- 28.8 +/- g/L) and in quality control workers (As, 23.9 +/- 18.1 microg/L; Be, 1.58 +/- 0.46 microg/L, and Se, 54.8 +/- 25.1 microg/L) are significantly higher than in the controls (As, 10.3 +/- 8.7 microg/L; Be, 0.83 +/- 0.46 microg/L; and Se, 32.3 +/- 13.5 microg/L). The possible connection of these elements with the etiology of disease and the possible role of selenium as a protective agent against the oncogenic and teratogenic action of other substances is discussed. We suggest the need for improvement of environmental conditions in the workplace through better ventilation and industrial hygiene practices.

Promotion of well-switching to mitigate the current arsenic crisis in Bangladesh.

To survey tube wells and households in Araihazar upazila, Bangladesh, to set the stage for a long-term epidemiological study of the consequences of chronic arsenic exposure. Water samples and household data were collected over a period of 4 months in 2000 from 4997 contiguous tube wells serving a population of 55000, the position of each well being determined to within +/- 30 m using Global Positioning System receivers. Arsenic concentrations were determined by graphite-furnace atomic-absorption spectrometry. In addition, groundwater samples collected every 2 weeks for an entire year from six tube wells were analysed for arsenic by high-resolution inductively coupled plasma-mass spectrometry. Half of the wells surveyed in Araihazar had been installed in the previous 5 years; 94% were privately owned. Only about 48% of the surveyed wells supplied water with an arsenic content below 50 micro g/l, the current Bangladesh standard for drinking-water. Similar to other regions of Bangladesh and West Bengal, India, the distribution of arsenic in Araihazar is spatially highly variable (range: 5-860 micro g/l) and therefore difficult to predict. Because of this variability, however, close to 90% of the inhabitants live within 100 m of a safe well. Monitoring of six tube wells currently meeting the 50 micro g/l standard showed no indication of a seasonal cycle in arsenic concentrations coupled to the hydrological cycle. This suggests that well-switching is a viable option in Araihazar, at least for the short term. Well-switching should be more systematically encouraged in Araihazar and many other parts of Bangladesh and West Bengal, India. Social barriers to well-switching need to be better understood and, if possible, overcome.

Preconcentration by coprecipitation of arsenic and tin in natural waters with a Ni-pyrrolidine dithiocarbamate complex and their direct determination by solid-sampling atomic-absorption spectrometry.

A method for the determination of trace amounts of arsenic and tin in natural waters is described. Trace amounts of arsenic and tin were preconcentrated by coprecipitation with a Ni-ammonium pyrrolidine dithiocarbamate (APDC) complex. The coprecipitates obtained were directly analyzed by graphite-furnace atomic-absorption spectrometry (GFAAS) using the Ni-APDC complex solid-sampling technique. The coprecipitation conditions used for the trace amounts of arsenic and tin in natural water were investigated in detail. It was found that arsenic and tin at sub-ng mL(-1) levels were both coprecipitated quantitatively by Ni(PDC)2 in the pH range 2-3. The concentration factors by coprecipitation reached approximately 40,000 when 2 mg nickel was added as a carrier element to 500 mL of the water sample. The proposed method has been applied to the determination of trace amounts of arsenic and tin in river water and seawater reference materials, and the detection limits for arsenic and tin, which were calculated from three times of the standard deviation of the procedural blanks, are 0.02 ng mL(-1) and 0.04 ng mL(-1), respectively, for 500-mL volumes of water sample.

Determination of selenium in soils by slurry-sampling graphite-furnace atomic-absorption spectrometry with polytetrafluoroethylene as silica modifier.

A 6% slurry of polytetrafluoroethylene (PTFE) in 4% hydrofluoric acid and 1% nickel nitrate were used as modifiers for determination of selenium in soils by GF AAS. PTFE was used to remove silica from the soil sample, because this resulted in severe matrix effects. The temperature of fluorination, determined thermogravimetrically, was 600 degrees C. The yield of fluorination depends on the molar ratio of PTFE/silica, particle size, and the time and temperature of fluorination. The soil samples were pretreated with a small amount of concentrated hydrofluoric acid placed directly in the cup of autosampler. The results for the determination of selenium in the reference soil materials by means of the slurry-sampling technique and use of aqueous standards are in good agreement with the certified values.

Direct determination of silicon in powdered aluminium oxide by use of slurry sampling with in situ fusion graphite-furnace atomic-absorption spectrometry.

A direct method for determination of silicon in powdered high-purity aluminium oxide samples, by slurry sampling with in situ fusion graphite-furnace atomic-absorption spectrometry (GF-AAS), has been established. A slurry sample was prepared by 10-min ultrasonication of a powdered sample in an aqueous solution containing both sodium carbonate and boric acid as a mixed flux. An appropriate portion of the slurry was introduced into a pyrolytic graphite furnace equipped with a platform. Silicon compounds to be determined and aluminium oxide were fused by the in situ fusion process with the flux in the furnace under optimized heating conditions, and the silicon absorbance was then measured directly. The calibration curve was prepared by use of a silicon standard solution containing the same concentration of the flux as the slurry sample. The accuracy of the proposed method was confirmed by analysis of certified reference materials. The proposed method gave statistically accurate values at the 95% confidence level. The detection limit was 3.3 microg g(-1) in solid samples, when 300 mg/20 mL slurry was prepared and a 10 microL portion of the slurry was measured. The precision of the determination (RSD for more than four separate determinations) was 14% and 2%, respectively, for levels of 10 and 100 microg g(-1) silicon in aluminium oxide.

Determination of Indium and Tellurium in Fifty Nine Geological Reference Materials by Solvent Extraction and Graphite Furnace Atomic Absorption Spectrometry

The indium (In) and tellurium (Te) contents of fifty nine geological reference materials, issued by several reference material producers (USGS, CRPG, ANRT, GIT‐IWG and GSJ) have been determined by graphite furnace atomic absorption spectrometry, after aqua regia and HF digestion, and extraction of iodide complexes with trioctylmethylammonium (TOMA) ‐ metyl isobutyl ketone (MIBK). Although the interferences from most elements can be minimised by the addition of palladium solution as the matrix modifier, large concentrations of Bi, Cu, Pb or Sn suppress the absorbance of In and/or Te. Samples for analysis were therefore restricted to those in which the concentrations of these interfering elements did not cause a significant interference. The limit of detection was 0.2 ng g−1 In and Te for 1 g test portions. The agreement between the reported results and published data is satisfactory.

Volatile organic compounds, polycyclic aromatic hydrocarbons and elements in the air of ten urban homes.

Ten homes were monitored at regular intervals from June 1994 through April 1995 as part of a Public Health Assessment in Southeast Chicago for exposure to volatile organic compounds (VOCs), polycyclic aromatic hydrocarbons (PAHs), and elements. Simultaneous 24-h indoor and outdoor samples were collected. VOCs were and analyzed using USEPA Method TO-14 with Selected Ion Monitoring Mass Spectrometry (GC/MS). PAHs were analyzed using USEPA Method TO-13 with GC/MS. Elements were collected on quartz fiber filters and analyzed by Inductively Coupled Argon Plasma (ICP) spectroscopy or Graphite Furnace Atomic Absorption (GFAA). Continuous measurements of CO2 and temperature were recorded for each indoor sample. Twenty-four h total CO2 emissions were determined from occupancy and estimated gas stove usage and were moderately correlated (R2 = 0.19) with 24 h average indoor CO2 concentrations. Modeled 24-h air exchange rates ranged from 0.04 to 3.76 air changes h-1 (ACH), with mean of 0.52 ACH. Median particle penetration was 0.89. Emission rates were calculated for each pollutant sampled. Using a detailed housing survey and field sampling questionnaires, it was possible to evaluate associations between housing characteristics and source activities, and pollutant source rates. The data indicate that several predictor variables, including mothball storage, air freshner use, and cooking activities, are reasonable predictors for emission rates for specific pollutants in the homes studied.

Slurry sampling electrothermal vaporization inductively coupled plasma mass spectrometry for steelmaking flue dust analysis

A commercial atomic absorption graphite furnace (AAGF), with a self-made adapter and valve system, was used as a slurry sampling cell for electrothermal vaporization inductively coupled plasma mass spectrometry (ETV-ICP-MS). The system was applied to the determination of As, Sn, Sb, Se, Te, Bi, Cd, V, Ti and Mo in steelmaking flue dusts. Experimental conditions with respect to ETV and ICP-MS operating parameters were optimized. Compared to aqueous solutions, slurry samples were found to present better analyte transport. Microgram amounts of Rh were used to reduce the difference in analyte response in sensitivity for aqueous solutions of the tested analytes. No such increasing effect was observed for slurry samples and aqueous standards. An added quantity of Rh acting as modifier/carrier resulted in an increase for the same analytes in matrix-slurry solutions, even the addition of an extra Rh quantity has resulted in a decrease in the signals. The effect of Triton X-100 (used as a dispersant agent) on analyte intensity and precision was also studied. External calibration from aqueous standards spiked with 100 μg ml −1 Rh was performed to quantified 0.010 g/100 ml slurry samples. Results are presented for a certified reference electrical arc furnace flue dust (EAF): CRM-876-1 (Bureau of Analysis Samples Ltd., Cleveland, UK), a reference sample of coke ashes X-3705 (from AG der Dillinger Hüttenwerke, Germany), and a representative sample of EAF flue dust from a Spanish steelmaking company (CENIM-1). For the two reference materials an acceptable agreement with certificate values was achieved, and the results for the CENIM sample matched with those obtained from conventional nebulization solution.

Espectrometria de absorção atômica multielementar simultânea com atomização eletrotérmica em forno de grafite - uma revisão da técnica e aplicações

Este trabalho descreve uma revisão a respeito do emprego da técnica de espectrometria de absorção atômica simultânea em forno de grafite (SIMAAS) em determinações multielementares de elementos-traço em diferentes matrizes. Os principais parâmetros envolvidos e que devem ser considerados em medidas multielementares, tais como, fonte de radiação, geometria do forno, programa de aquecimento e natureza e quantidade de modificador químico, são descritos.

Atomic absorption with ultracold atoms

Recent advances in laser-atom cooling techniques and diode-laser technology now allow one to conduct an idealised atomic absorption experiment comprising a sample of ultracold, quasi-stationary absorbing atoms and a source of near-monochromatic resonant light. Under such conditions, the atomic absorption coefficient at line centre is independent of the oscillator strength of the atomic resonance line. This offers the prospect of ‘oscillator-strength-free’ atomic absorption spectroscopy in which the absorption signal is equally large for both strong and weak (closed) transitions of the same wavelength and in which absolute atomic absorption could be performed without knowledge of the oscillator strength. Moreover, the resolution and sensitivity for a given atom density are greatly enhanced, typically by approximately three orders of magnitude (and even more for weak transitions), compared with conventional flame or graphite-furnace atomic absorption. We describe an atomic absorption experiment based on samples of ultracold, laser-cooled caesium atoms and a narrow-bandwidth diode laser source that approximates the idealised conditions for oscillator-strength-free atomic absorption. The absorption measurements are used to determine the number density and temperature (approx. 6 μK) of the sample of ultracold atoms. Some of the technical obstacles that would have to be overcome before samples of ultracold atoms and diode laser sources could be used in analytical atomic absorption spectroscopy are discussed.

The Role of Copper, Molybdenum, Selenium, and Zinc in Nutrition and Health

Copper, zinc, selenium, and molybdenum are involved in many biochemical processes supporting life. The most important of these processes are cellular respiration, cellular utilization of oxygen, DNA and RNA reproduction, maintenance of cell membrane integrity, and sequestration of free radicals. Copper, zinc, and selenium are involved in destruction of free radicals through cascading enzyme systems. Superoxide radicals are reduced to hydrogen peroxide by superoxide dismutases in the presence of copper and zinc cofactors. Hydrogen peroxide is then reduced to water by the selenium-glutathione peroxidase couple. Efficient removal of these superoxide free radicals maintains the integrity of membranes, reduces the risk of cancer, and slows the aging process. On the other hand, excess intake of these trace elements leads to disease and toxicity; therefore, a fine balance is essential for health. Trace element--deficient patients usually present with common symptoms such as malaise, loss of appetite, anemia, infection, skin lesions, and low-grade neuropathy, thus complicating the diagnosis. Symptoms for intoxication by trace elements are general, for example, flu-like and CNS symptoms, fever, coughing, nausea, vomiting, diarrhea, anemia, and neuropathy. A combination of observation, medical and dietary history, and analyses for multiple trace elements is needed to pinpoint the trace element(s) involved. Serum, plasma, and erythrocytes may be used for the evaluation of copper and zinc status, whereas only serum or plasma is recommended for selenium. Whole blood is preferred for molybdenum. When trace element levels are inconsistent with medical evaluations, a test for activity of the suspected enzyme(s) would support the differential diagnosis. Furthermore, it is important to differentiate whether trace element deficiency or toxicity is the primary cause of the disorder, or is secondary to other underlying diseases. Only successful treatment of the primary disorder will lead to complete recovery. In the event of sample contamination during collection or analysis, the physician may be misled by falsely elevated results. Royal blue top evacuated tubes containing negligibly low concentrations of the trace element or acid-washed plastic sterilized syringes should be used for blood, serum, or plasma collection. Powdered gloves must be avoided. When possible, mineral supplements are not to be administered to the patient for a minimum of 3 days prior to sample collection. Serum and plasma specimens are to be transported in acid-washed polypropylene and polyethylene tubes. Analysis is performed in a controlled environment to minimize or eliminate contamination. During analysis, all laboratory wares should be acid-washed for decontamination. A detailed description of these precautions may be found in reviews by Aitio and Jarvisalo and by Chan and Gerson. Copper and zinc analysis on serum and plasma are commonly performed by flame atomic absorption spectrometry, inductively coupled plasma-atomic emission spectrometry, and inductively coupled plasma-mass spectrometry. Serum and plasma selenium levels are determined by graphite furnace atomic absorption with Zeeman background correction and neutron activation analysis. Molybdenum levels are best determined by neutron activation and highly sensitive inductively coupled plasma-mass spectrometry. The reader is referred to reviews by Tsalev and Jarvis.

Trace element profile of semiconductor materials: Gallium and arsenic

An ion exchange methodology is described here for the quantitative separation and determination of trace elements from high purity gallium, arsenic and a mixture of gallium and arsenic. 0.5–2 g of the matrix is dissolved and subjected to an ion exchange separation process in acidic/alkaline (hydrochloric acid/ammonia with sodium hydroxide) medium to preconcentrate the analytes. The desorbed analytes were quantified using graphite furnace atomic absorption spectrometry/flame atomic absorption spectrometry/flame atomic emission spectrometry/neutron activation analysis/inductively coupled plasma atomic emission spectrometry. Most of the analytes were found to be present at extreme trace levels. The overall reproducibility of the procedure was 2–10% when compared with the blank values. Separation of the analytes were essentially complete as the recoveries were >95% which was confirmed by standard addition to the matrices and tracer studies.

Comparison of Techniques for the Analysis of Industrial Soils by Atomic Spectrometry

Methods based on AAS, ICP-AES and XRFS have been developed for determination of Cd, Cr, Cu, Mn, Ni, Pb, V and Zn in soil layers from pits excavated on a redundant industrial site. Samples were dried and sieved, and the < 2 mm fraction was ground in a ball mill prior to analysis. For ICP-AES and AAS, 1 g sub-samples were digested with aqua regia in a microwave oven. The dry weight detection limits of the analytes were in the range 2–25 μg g−1 for FAAS, 0.003–0.2 μg g−1 for ETA AS and 0.04–1.6 μg g−1 for ICP-AES. When digests of the industrial soils were analysed, calibration with acid-matched standards gave acceptable accuracy for all the analytes, except for Cd when determined by ETAAS (30–40 % suppression). Despite lack of reference materials of industrial origin, analysis of two soil reference materials by these techniques produced concentrations that were within ± 10 % of the certified or recommended values for elements extractable with aqua regia. Direct standard-less analysis of a soil reference material with a portable x-ray fluorescence (P-XRF) analyser gave concentrations for a range of elements that were within a factor of 2 of the certified values. When the XRFS and ICP-AES methods were used to analyse the industrial soils, the concentrations obtained were similar (to within 30%) for Cu, Pb and Zn in most of the samples and for Cr, Mn and Ni in some of the samples. The concentrations of V estimated with the P-XRF analyser were 4 to 7-fold higher than those obtained by ICP-AES. The discrepancies were thought to be caused by spectral enhancement interferences in XRFS. Cadmium was not determined accurately by either ICP-AES or P-XRFS owing to spectral interferences. The work has highlighted the importance of analysing samples from across a site and at different depths, when assessing the extent of metal contamination on industrial land.

Determination of nickel(II) and cobalt(II) in an aqueous solution using 4-(2-Pyridylazo)-resorcinol/Capriquat-loaded silica gel.

The separation and preconcentration of trace nickel(II) and cobalt(II) form an aqueous solution for a graphite-furnace atomic-absorption spectrometric (GF-AAS) determination was studied using silica gel loaded with 4-(2-Pyridylazo)-resorcinol (PAR)/trioctylmethylammonium chloride (Capriquat). The proposed adsorbent was prepared as follows: ten grams of silica gel were shaken into 25 ml of a 5% Capriquat-xylen solution and a 0.01% PAR solution for 30 minutes. A sample solution of 1001000 ml containing Ni(II) and Co(II) was adjusted to pH 9.0. The solution was then passed through 1.0 g of PAR/Capriquat-loaded in a silica gel column at a flow rate of 10 ml min-1. The Ni(II) and Co(II) collected on the PAR/ Capriquat-loaded silica gel on the column was eluted with 10 ml of 0.2 M nitric acid, and then deteminated by GF-AAS. In this method, over 99% of the Ni (II) and Co(II) was adsorbed at about pH 9.0. The calibration curve was linear from 0.05 to 2.5 μg/1 Ni(II) and 0.03 to 3.0 μg/l Co(II). The proposed method has been applied to the determination of Ni(II) and Co(II) in sea-water samples.

Transplacental passage of aluminum from pregnant mice to fetus organs after maternal transcutaneous exposure.

Aluminum is present in tap water, antiperspirants and cosmetics up to 20%. Teratogenicity of aluminium was clearly identified after per os or intravenous administration. Malformations and other alterations by aluminium intoxication were evaluated in fetus. In the present study, we investigated the possible transplacental passage of aluminium and its accumulation in the tissue after cutaneous uptake. Female Swiss mice received aluminium chloride by cutaneous way (0.4 micrograms/day) during 20 days of gestation. The samples were assayed for aluminium quantification by graphite furnace atomic absorption with Zeeman correction. This treatment led to an increase of aluminum in maternal and fetus samples (serum, amniotic fluid and organs) as compared to controls.