Granular Size Research Articles

Effect of granular activated carbon particle sizes and depths in slow sand filter on water purification

Most rural dwellers in Nigeria depend on contaminated water from ponds, streams and wells for drinking water. Every household needs simple water purification device like Slow Sand Filter (SSF) to prevent water-borne diseases. This study was conducted to determine the effect of Granular Activated Carbon (GAC) particle sizes and depths in SSF on the purification of water. Two sets of SSF were fabricated using 6 inches (15.24cm) diameter PVC pipe, fine sand (0.25 mm grain size) with 35 cm depth. GAC for the first set SSFs (particle sizes 10 mm, 14 mm with 15 cm depth) and GAC for the second set of the SSFs has 15 and 25 cm depths with particle size 10 mm. The SSF has 50 litres storage tank from which raw water flows into the filter chamber (15.25 diameter and 110 cm long PVC). The filter was kept moist for 21 days for schmutzdecke to fully develop which is effective in trapping bacteria. Raw water was poured into the SSF, water samples were collected and analyzed using standard methods. The SSF has a capacity of producing 35 litres/h clean water. Percentage reduction of Lead, Manganese, Copper, Iron, Turbidity and Total Coliform Counts of the filtered water compared with the control were 91.35-99.88%, 90.00-98.33%, 42.00-100.00%, 46.67-100.00%, 13.04-99.15% and 16.67-57.69%, respectively. The SSF increased pH and Calcium by 7.14-27.71% and 83.65-98.21%, respectively. SSF with 10 mm and 25 cm depths GAC reduced the pollutants than the other two filters and it is recommended for purifying pond water.

THE SIMULATION OF GRANULAR PARTICLE ON DRY AND MOISTURIZED POROUS HORIZONTAL SURFACES

Simulations were carried out to visualize the ratio of granular attachment to porous surfaces. This simulation uses a uFlex three-dimensional simulation using three sizes of porous surface systems in the condition of the smallest human pores and the most extensive human pores and the condition of wet skin and dry skin. Each system was tested using five granular particle sizes according to the range of the makeup granules’ size to determine the optimal adhesive. The results show that the number of cosmetic granular particles entering the porous surface system is directly proportional to the porous surface volume and moisture and inversely proportional to the granular cosmetic size. The larger the cosmetic granular used, the less granular enters the pore.

Fuel Injection Responses and Particulate Emissions of a CRDI Engine Fueled with Cocos nucifera Biodiesel

The objective of this paper is to study the effect of coconut oil biodiesel (COB)-diesel blends on exhaust particulate matter (PM) emissions and fuel injection responses in an unmodified turbocharged four-stroke common-rail direct injection (CRDI) diesel engine. Characterization of COB and their blends has been conducted to ascertain the applicability of these fuels for the existing engine. The test fuels used were fossil diesel fuel, COB10, COB20, COB30 and COB50 of biodiesel-diesel fuels. A test cycle which composed of 16 different steady-state modes at various loads and speed conditions was followed. Generally, the results showed a marginally advanced SOI timing and longer injection duration with increasing COB blends at higher load as compared to diesel fuel. Additionally, the lower calorific value (CV) and higher viscosity of the COB fuel blends have resulted in reduced turbo boost pressure and increased common-rail fuel injection pressure, respectively, across all engine speeds and loads. On the aspects of PM emissions characterization, results indicated that the blending of COB with conventional diesel had benefits over diesel in PM reduction. In fact, the largest achievable PM mass reduction of 38.55% was attained with COB50. In addition, it was noticed that the size of PM particles accumulated such that the granular size increased with higher diesel content in the blend. Additionally, the composition analysis on the PM collected by EDX spectroscopy has revealed that the C, O and Si as three main elements that made up the PM particles in descending order. Overall, the results indicated that COB biodiesel is a clean-burning alternative fuel and can be used satisfactorily in an unmodified diesel engine without the needs for engine remapping.

Exploring the Biomaterial-Induced Secretome: Physical Bone Substitute Characteristics Influence the Cytokine Expression of Macrophages.

In addition to their chemical composition various physical properties of synthetic bone substitute materials have been shown to influence their regenerative potential and to influence the expression of cytokines produced by monocytes, the key cell-type responsible for tissue reaction to biomaterials in vivo. In the present study both the regenerative potential and the inflammatory response to five bone substitute materials all based on β-tricalcium phosphate (β-TCP), but which differed in their physical characteristics (i.e., granule size, granule shape and porosity) were analyzed for their effects on monocyte cytokine expression. To determine the effects of the physical characteristics of the different materials, the proliferation of primary human osteoblasts growing on the materials was analyzed. To determine the immunogenic effects of the different materials on human peripheral blood monocytes, cells cultured on the materials were evaluated for the expression of 14 pro- and anti-inflammatory cytokines, i.e., IL-6, IL-10, IL-1β, VEGF, RANTES, IL-12p40, I-CAM, IL-4, V-CAM, TNF-α, GM-CSF, MIP-1α, Il-8 and MCP-1 using a Bio-Plex® Multiplex System. The granular shape of bone substitutes showed a significant influence on the osteoblast proliferation. Moreover, smaller pore sizes, round granular shape and larger granule size increased the expression of GM-CSF, RANTES, IL-10 and IL-12 by monocytes, while polygonal shape and the larger pore sizes increased the expression of V-CAM. The physical characteristics of a bone biomaterial can influence the proliferation rate of osteoblasts and has an influence on the cytokine gene expression of monocytes in vitro. These results indicate that the physical structure of a biomaterial has a significant effect of how cells interact with the material. Thus, specific characteristics of a material may strongly affect the regenerative potential in vivo.

A Study of Substitution the Element of (La+3) on the Structural and Electrical Properties of the Compound Ferrite (𝐂𝐨𝟎.𝟐𝟓𝑵𝒊𝟎.𝟐𝟓𝐙𝐧𝟎.𝟓𝐋𝐚𝐱𝐅𝐞𝟐−𝐱𝐎𝟒)

The ferritic nanocomposite which prepared has the chemical formula of (Co0.25𝑁𝑖0.25Zn0.5LaxFe2−xO4), for different values of (X= 0, 0. 25, 0. 5, 0. 75), by using the spontaneous combustion-gel method, where calcination had been at temperature of (700˚C) for two hours; then studied the structural properties of the resulting ferrite via X-Ray diffraction (XRD), and Scanning Electron Microscopy (SEM) The results denote that the ferrite has a unique phase with a spinal-shaped crystal structure and a granular size are (23-36) nm, with increase in lattice constant of decrease in porosity, and electrical properties were also take in to consideration, like value of dielectric constant, the loss coefficient also observed via increase the frequency. The alternating electrical conductivity (σa.c) increases with increasing frequency.

Time Granularity Impact on Propagation of Disruptions in a System-of-Systems Simulation of Infrastructure and Business Networks.

A system-of-systems (SoS) approach is often used for simulating disruptions to business and infrastructure system networks allowing for integration of several models into one simulation. However, the integration is frequently challenging as each system is designed individually with different characteristics, such as time granularity. Understanding the impact of time granularity on propagation of disruptions between businesses and infrastructure systems and finding the appropriate granularity for the SoS simulation remain as major challenges. To tackle these, we explore how time granularity, recovery time, and disruption size affect the propagation of disruptions between constituent systems of an SoS simulation. To address this issue, we developed a high level architecture (HLA) simulation of three networks and performed a series of simulation experiments. Our results revealed that time granularity and especially recovery time have huge impact on propagation of disruptions. Consequently, we developed a model for selecting an appropriate time granularity for an SoS simulation based on expected recovery time. Our simulation experiments show that time granularity should be less than 1.13 of expected recovery time. We identified some areas for future research centered around extending the experimental factors space.

An investigation into the optimal granular sludge size for simultaneous nitrogen and phosphate removal

An aerobic granular sludge (AGS) pilot plant fed with a mixture of acetate amended centrate and secondary effluent was used to investigate the optimal granule size range for simultaneous nitrification and denitrification (SND) and ortho-phosphate removal. The anaerobic phase was mixed to understand how AGS will perform if integrated with a continuous flow activated sludge system that cannot feed the influent through the settled sludge bed. Five different granule size fractions were taken from the pilot (operated at DO setpoint of 2mgO2/L) and each size was subjected to activity tests in a well-controlled lab-scale AGS reactor at four dissolved oxygen (DO) concentrations of 1, 2, 3, and 4 mgO2/L. The size fractions were: 212 – 600 µm, 600 – 1000 µm, 1000 – 1400 µm, 1400 – 2000 µm, and >2000 µm. The smallest size range (212 – 600 µm) had the highest nitrification and phosphate removal rates at DO setpoints from 1 – 3 mgO2/L, which was attributed to the higher aerobic volume fraction in small granules and hence a higher abundance of phosphorus accumulating organisms (PAO) and ammonia oxidizing bacteria (AOB). In comparison, large granules (>1000 µm) had 1.4 – 4.7 times lower ammonia oxidation rates than the smallest size range, which aligned with their lower AOB abundance relative to granule biomass. The granules with the highest anoxic volume fraction had the highest abundance of nitrite reductase genes (nir gene) but did not show the highest specific nitrogen removal rate. Instead, smaller granules (212 – 600 and 600 – 1000 µm), which had a lower nir gene abundance, had the highest specific nitrogen removal rates (1.2 – 3.1 times higher than larger granules) across all DO values except at 4 mgO2/L. At a DO setpoint of 4 mgO2/L, nitrite production by ammonia oxidation (ammonia monooxygenase) exceeded nitrite reduction by nitrite reductase in granules smaller than 1000 µm, in addition, some denitrifying heterotrophs switched to oxygen utilization in deeper layers hence suppressing denitrification activity. At the DO range of 2 – 4 mg/L, granular size had a greater effect on nutrient removal than DO. Therefore, for AGS developed at an average DO setpoint of 2 mgO2/L, selecting for size fractions in the range of 212 – 1000 µm and avoiding DO values higher than 3 mgO2/L can achieve both a higher nitrogen removal capacity and energy savings. This study is the first to investigate the influence of different DO values on SND and biological phosphorus removal performance of different aerobic granular sludge sizes.

Mechanical and dynamic properties of composite rubber (RSS and SBR) with waste rubber crumb and copper fiber

Waste rubber tire is difficult to decompose by nature, but it can be reused as a part of composite rubber materials. In this research, waste rubber crumb was mixed into Ribbed Smoked Sheets (RSS) and Styrene-Butadiene Rubber (SBR) compound to form a composite rubber. The aim of this research is to investigate the mechanical and dynamic properties of RSS and SBR compounds with waste rubber crumb and copper fibber. For this purpose, another composite material in the form of copper fiber is also added which is expected to increase the damping properties of the rubber even though the mechanical properties of the rubber will decrease. RSS and SBR rubber compounds consist of 25-phr and 50-phr waste rubber crumb. Waste rubber crumb is taken from used vehicle tires with the granular size passes through the mesh sieve number # 100. 5-phr, 10-phr, 20-phr, and 30-phr of copper fibers were added into 25-phr and 50-phr respectively. The copper fiber used is 0.3 ± 0.05 mm in diameter and length to diameter ratio is 40. The results of this study indicate that the addition of waste rubber 25-phr and 50-phr decreases the tensile strength, elastic modulus, and shear modulus but increases the damping properties. The addition of copper fiber 5-phr until 30-phr decreses the tensile strength and elastic modulus but increases the shear modulus and the damping properties.

Surface Hardness Modify and Improve Wear Properties of EP\ NanoZrO2

The liquid and mechanical mixing method was used in addition to ultrasound technology to prepare samples according to standard conditions. The percentage of cementing with ceramic powder was adopted from 1% to 4% as a weight ratio, and by using mixing drivers, nanocomposites were prepared depending on the theoretical density of the components. The velvet density was measured using Archimedes' method, and the results showed a successive improvement and increase in density with the weight ratio of addition. The results of the particulate hardness test showed a significant improvement in the results of the prepared nanostructures compared to the base sample (pure epoxy). With regard to the properties of wear resistance (wear modulus) using the screw-on-disk method, the cemented samples showed a higher wear resistance compared to the base sample. The results were interpreted based on the values of density and hardness in addition to the properties possessed by the ceramic powder of high surface area and average granular size of 32 nanometers through scanning electron microscopy. In this work, nanostructures based on (a polymer) supported with nanoscale zirconium dioxide powder were developed.

EXPERIMENTAL STUDY ON COMPRESSIVE STRENGTH AND FLEXURAL RIGIDITY OF EPOXY GRANITE COMPOSITE MATERIAL

In Egypt, large quantities of coarse granite wastes are produced annually during the quarrying operations of granite rocks. This waste represents a potentially useful source of material for a variety of applications such as a filler material in epoxy granite composite material. In this work a new eco-friendly composite material studied as a substitute for machine tools traditional materials, like cast iron, to produce better efficiency with lower cost. This study aims to investigate the mechanical properties of granite epoxy composite by using the local epoxy (kemapoxy 150) and the granite residues in the Egyptian quarries. The investigated processing variable was epoxy content, and the mechanical characterization ware carried out by compressive and flexural tests according to the ASTM standard method B. Commercially available, Aswan red granite was procured, crushed, and sieved to three size ranges from 0.150 to 8 mm, respectively. Epoxy ratios of 80:20, 85:15 have been used with granite aggregate size mix with small, medium, and coarse size proportions of 50:25:25 respectively for preparing the specimens with granite granular size range (0.150-8) mm. The results show that Epoxy granite composite with granite to epoxy ratio of 80:20% wt. induced the highest compressive strength (72.15 MPa) while the composite with the ratio of 85:15% wt. induced the highest flexural strength (20.1 MPa). Epoxy granite composite show superior results with respect to cement concrete, polyester concrete, and natural granite.

The prediction of partial-nitrification-anammox performance in real industrial wastewater based on granular size

To date, the partial nitrification-Anammox (PN-A) granular sludge size has been exclusively analyzed in synthetic substrates. In this work, different ranges of granular size of PN-A sludge were studied at low oxygen concentration using real industrial wastewater as, well as a synthetic substrate. The granular sludge was characterized by the specific nitrification activity (SNA), specific anammox activity (SAA), and granule sedimentation rate. The relative abundance of the bacterial consortium was assessed for each range of diameters through the fluorescence in situ hybridization (FISH) technique. SNA exhibits a direct association with the specific surface of granules, which proves the importance of the outer layer in the nitrification process. Even more critical, the flocculent sludge allowed the stability of the nitrifying activity. The SAA showed different performances faced the real industrial and synthetic substrates. With the synthetic substrate, the SAA decreased at higher diameter ranges, whereas with the industrial substrate, the SAA increased at higher diameter ranges. This situation is explained by the oxygen protection in the sludge maintained with industrial wastewater. The relative abundance of heterotrophic bacteria increased from 9.6 to 22%, due to the presence of organic matter in the industrial substrate. The granular sedimentation rate increased with the diameter of the granules with a linear correlation (R2 > 0.98). Thus, granular sizes can be selected through sedimentation rate control. A linear correlation between SAA and granular sludge diameter ranges was observed. With this correlation, an error of less than 11% in the prediction of SAA was achieved. The use of diameter measurement and granular sedimentation rate as routine techniques could contribute to the control and start-up of PN-A reactors. In the same sense, organic matter present in defined concentrations, can be beneficial for the granular sludge stability, and thus, for nitrogen removal.

Thermoset Polymer Matrix Composites of Epoxy, Unsaturated Polyester, and Novolac Resin Embedding Construction and Demolition Wastes powder: A Comparative Study.

Composite materials that consisted of a polymer resin as matrix (PMCs), filled using construction and demolition (C&D) wastes powder of different grain sizing in micro-scale were manufactured and studied. Three different kinds of resins were used as the matrix for the purposes of this study. More specifically, composites made of epoxy and unsaturated polyester resins purchased from the market and phenolic resin (novolac) laboratory synthesized, were produced. The morphological and elemental analysis of these materials was performed through scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX), and X-ray diffraction (XRD). Additionally, mechanical performance and thermal insulating efficiency of these materials were examined through bending and shear strength tests according to the three-point method and via determination of the thermal conductivity coefficient λ. C&D wastes have undergone the appropriate processing in order to prepare filling products of the required granular size in pulverized form. In this research study, construction and demolition waste-based thermosetting polymer composites were produced with flexural strength in the range 20–60 MPa, shear strength in between 1–8 MPa, and thermal conductivity coefficients in the range of 0.27–1.20 W/mK. The developed materials embedded 30–50% w/w C&D wastes, depending on the resin used as the matrix.

In Vivo Evaluation of Oxygenic Photogranules’ Photosynthetic Capacity by Pulse Amplitude Modulation and Phototrophic–Irradiance Curves

The commingled microbial moiety of oxygenic photogranules (OPGs) facilitates aeration-free wastewater treatment. Embedded in an extracellular polymeric substances (EPS) matrix, microbial producers and consumers of oxygen occupying granular niches exchange substrates among themselves and with the bulk fluid. An assessment of the OPG’s phototrophic potential or functional capacity may require combining different photoactivity signals. The photosynthetic capacity was evaluated using photosynthetic oxygen evolution (POE) and chlorophyll fluorescence (rapid light curves, RLC) measurements using OPGs grown at different light intensities.. A maximum oxygen generating capacity for optimal OPGs and reactor conditions was determined to be 284.4 mgO2 gVSS–1 h–1 The OPGs exhibited photoelasticity, with higher photosynthetic capacity in high light (HL) compared to that in low light (LL) adapted samples. Saturation irradiances before the onset of photoinhibition for LL and HL samples were 1000 and 1200 μmol m–2 s–1, respectively using POE signals, and 478 μmol m–2 s–1 and 611 μmol m–2 s–1 using RLC signals. Moreover, HL adapted samples had higher nonphotochemical quenching rates which allude to the OPG’s photoelastic potential. The correlation coefficients (κ) between POE and RLCs were lower than reported values for pure microbial cultures reflecting the enhanced contribution from different photosynthetic clades with a variety of light-harvesting pigments present in OPGs. In an OPG reactor, the photochemical activity can be influenced by the granular size, granular ecology, and reactor operation metrics related to irradiance interactions such as mixing, self-shading, light intensity, photoperiods, and reactor depth. This presents opportunities for design of intensive wastewater resource recovery using phototrophic granular biomass.

Biophysical Characterization of Thin Films of Zinc Oxide Prepared by Sol-Gel

In this research, ZnO nano-powder was used, and the work was in two biological and physical parts. Where the work of the first part was to examine the effect of ZnO powder on Staphylococcus aureus, and the result of inhibition was 100%. As for the second part, the preparation of a thin film by the Sol-Gel method, where thin films were deposited on glass, the structural properties and topography of the surface were studied. The prevailing trend (101). Also, the results of the atomic force microscopy (AFM) tests showed that the resulting granular size of the prepared and annealed films with a temperature (400 ° C) was less than 100 nm, wherein an anti-bacterial nanoscale S. aureus was made.

Effects of anaerobic granular sludge towards the treatment of flowback water in an up-flow anaerobic sludge blanket bioreactor: Comparison between mesophilic and thermophilic conditions

Cost-effective treatment of flowback water remains a challenge for the sustainability of shale gas development. This study evaluated the efficiency of anaerobic granular sludge (AnGS) technology for flowback water treatment under mesophilic and thermophilic conditions. The granule characteristics and metagenomic characterization were also investigated. Thermophilic AnGS achieved 70.9% of COD removal and 362 NmL/d of methane production, higher than those for mesophilic AnGS (60.0% and 241 NmL/d). Thermophilic AnGS had higher extracellular polymeric substances content but low granular size and settleability. Metagenomic analysis revealed the genes related to hydrolysis acidification and carbohydrate metabolism were upregulated during thermophilic condition. Thermophilic condition most likely improved the hydrolysis of complex organics in the flowback water such as guar gum and hydrolyzed polyacrylamide, and led to higher COD removal and methane production. These results suggest that AnGS technology is a promising alternative for the treatment of flowback water, particularly when operated at thermophilic condition.

Evaluating Microbial Interactions of Autotrophs and Heterotrophs in Partial Nitritation/Anammox (PN/A) Process by Experimental and Simulation Analyses

The microbial interactions between autotrophs and heterotrophs by the exchange of microbial products in a partial nitritation/anammox (PN/A) bioreactor were evaluated with both experimental and simulation analyses. Real-time quantitative PCR analysis showed that anammox bacteria (AMX) and ammonium oxidizing bacteria (AOB) made up 56.59% and 8.35% of total bacteria, respectively, while heterotrophs identified as Chloroflexi also constituted a large portion (32.76%) in the reactor, even without an external organic carbon supply. Furthermore, a mathematical model was developed to describe the growth of heterotrophs on soluble microbial products (SMP), which were released from the metabolism of autotrophs. After model calibration and validation, the simulation results were consistent with the experimental observations of the microbial composition and the nitrogenous transformations. According to the model analysis, the bulk oxygen concentration was determined to be the dominant factor governing the reactor performance and biomass fractions in the granule. Increasing granular size could decrease heterotrophic growth, but has little effect on the effluent concentration of SMP. Results of this study could establish a better understanding of eco-physiological interactions of autotrophs and heterotrophs in PN/A process.

High-performance large-area WS2-based transistors by a novel tin-oxide assisted liquid-phase exfoliation: doping adjustment by plasma treatment

We report a novel strategy to stitch small WS2 flakes to form larger features in liquid-phase exfoliation. Owing to the initial granular size of the bulk WS2, which, is around 2 µm, the use of conventional liquid-based exfoliation techniques leads to small area nanoflakes with sizes around 1 μm. However, by joining smaller flakes through tin-oxide quantum dot (SnO2 QD) decoration during probe sonication, sheets up to 20 μm are achieved. The neighboring flakes could stitch together to form larger features through the Sn–S and Sn–O bonds at their lateral sides of their flakes and to realize mosaic arrangement of arbitrary shaped larger sheets. While the original WS2 flakes show n-type behavior, an interesting conversion into a p-channel behavior is observed upon addition of SnO2 QDs followed by additional SF6 plasma treatment process. Additionally, we have investigated the use of SF6 plasma treatment to enhance the carrier mobility and on-off ratio of the field effect transistors, yielding an effective field-effect-mobility of 80 cm2 V−1 s−1 and relatively high on/off current ratio of 105, indicating its superior electronic properties.

Experimental investigation of mobility and deposition characteristics of dry granular flow

This paper presents an experimental investigation of mobility and deposition characteristics of dry granular flow, by a number of flume tests on silica sand no. 3 and silica sand no. 7, to interpret the effects of angle of slope, granular volume, cushion, granular structure, and granular size on the mobility and deposition characteristics of granular flow. Along a given slope, an increase of the amount of sand impaired its mobility. However, for a given amount of sand along a slope, an increase of the angle of slope resulted in a V-shaped change of the angle of mass center movement, implying the existence of a characteristic combination of the angle of slope and the amount of sand to yield the maximum mobility of granular flow. The angle of mass center movement increased while increasing the thickness of cushion, showing that the cushion impaired the mobility of granular flow. Granular structure using the mixed structures of silica sand no. 3 and silica sand no. 7 affected greatly the mobility of granular flow, by showing an inverted structure in the near runout area with the deposition of the materials in the upper half of original grading structure in the far runout area for the inverse grading structure and normal grading structure. The mobility of granular flow increased with the change in turn of the inverse grading structure, the uniform structure, and the normal grading structure. The increase of the grain sizes of granular material enhanced its mobility. In addition, the angle of mass center movement showed a more reliable assessment for the mobility of granular flow in comparison with the angle of maximum mass movement.

Polypropylene as an innovative substitute for jar material of horizontal axis, multi-jar ball milling machine to grind electrode materials for energy storage devices

It is approximated that there will be a considerable amount of increase in worlds energy needs. So, there is a need of high energy storing devices when the load is low or moderate. Supercapacitors (SC) can be the competent options to serve this purpose. The paper recounts the performance of supercapacitors (SC) churned out from a horizontal axis multi-jar ball milling machine based on variations in material properties of ball milling jars. To store ample amount of energy, it is very essential to develop energy storing devices with large capacities and large ratings. The performance of energy storage devices is investigated using Manganese dioxide and Activated carbon as electrode materials. Majority of the times the granular size of raw-electrode materials is not enough fine to use them as electrodes directly. As a result of this, it is essential to crush the raw-electrode materials of the SC into fine powder. The energy storing capacity of SCs depends on size of particle, specific area, the of material and quantity to weight ratio of electrode material. In this paper an alternative material ‘Polypropylene’ is used as a substitute for Aluminum jars in horizontal axis multi-jar ball milling machine to crush the electrode materials. The effectiveness of both the jars is compared by evaluating the performance parameters of the SCs manufactured from electrode materials crushed in each of these jars. It is observed that the performance of SCs depends on type of ball milling machine, number of ball milling balls used, ball milling time, diameter of ball milling jars, speed of ball milling and material of ball mill jars properties. So, all other parameters are kept the same except the material of ball mill jars to scrutinize the effect of ball milling jars on performance of SCs.

Micronutrients and Cod/N Ratio as Factors Influencing Granular Size, Autotrophic and Heterotrophic Nitrification and Denitrification in Aerobic Granular Sequencing Batch Reactors

Micronutrients and Cod/N Ratio as Factors Influencing Granular Size, Autotrophic and Heterotrophic Nitrification and Denitrification in Aerobic Granular Sequencing Batch Reactors