Good Stability Research Articles

Fabrication of a polyoxometalate-based metal-organic compound and its derivative for enhanced photocatalytic, electrocatalytic, and electrochemical sensing properties

A novel polyoxometalate-based metal-organic compound (POMOC), namely [Ag(3-pna)2(H2PW12O40)]n (compound 1, where 3-pna = N-(pyridine-3-yl)nicotinamide), had been successfully synthesized and structurally characterized. The photocatalytic performance of compound 1 for the degradation of gentian violet (GV) and methylene blue (MB) was investigated in detail, which exhibited good cyclic stability as a photocatalyst. In addition, cyclic voltammetry technology was used to verify that compound 1 exhibited excellent electrocatalytic performance towards KBrO3 and H2O2. To improve the degradation of organic dyes and electrochemical sensing performance, a negatively charged oxygen vacancy metal oxide compound 1@C was prepared via pyrolysis using compound 1 as a precursor. Compound 1@C was investigated as an adsorbent, and was found to effectively remove MB and GV from wastewater, with adsorption rates of 824.36 mg/g and 957.02 mg/g, respectively. The performance of compound 1@C/glassy carbon electrode as an electrochemical sensor was studied using differential pulse dissolution voltammetry (DPV). This method proved effective in detecting heavy metal ions Cd2+ and Pb2+ in wastewater with the limits of detection as 4.65 and 1.69 μg/L, respectively. Compound 1@C/GCE showed good anti-interference capabilities and stability in detecting heavy metal ions in wastewater.

Boosting oxygen reduction performance by copper-iron co-doped on ZIF-derived N-doped carbon nanotubes

Developing high-efficiency non-noble metal catalysts for the oxygen reduction reaction (ORR) is paramount for sustainable energy conversion. In this study, we proposed a Cu, Fe co-doped zeolite imidazole framework (ZIF)-derived nitrogen-doped carbon nanotubes catalyst (Cu-Fe@CNTs/NC) obtained by hydrothermal method and pyrolysis. The electrochemical results showed that Cu-Fe@CNTs/NC exhibited favorable oxygen reduction performance and good stability under alkaline electrolyte. The incorporation of Cu and Fe bimetallic dopants promoted the carbon nanotubes growth on ZIF nanosheets, and the collaborative action of Cu and Fe enhanced its ORR catalytic activity. These findings provide an innovative way to prepare high active non-platinum ORR catalysts.

CoMo/g-C3N4 as a highly effective, reusable, non-noble metal-based catalyst for H2 production via NaBH4 hydrolysis focused on stationary application under mild conditions: A kinetic study

Among hydrogen storage chemicals for proton exchange membrane fuel cells (PEMFCs), sodium borohydride stands out for yielding exceptionally pure hydrogen. This study synthesized cobalt-molybdenum catalysts supported on g-C3N4 using an ultrasonic-assisted impregnation method. Various CoMo/g-C3N4 catalysts with different CoMo mass ratios were created, all showing high hydrogen production and complete NaBH4 conversion under mild conditions. Catalytic activity depends on the cobalt-molybdenum mass ratio, with optimal performance at a 1:1 ratio (w/w), maintaining up to 83% activity over 5 cycles. The effect of operating conditions on hydrogen release was explored, resulting in the rate law: rH2 = 1.708 × 10-3 [NaBH4]1.25 [Catalyst dosage]1.39 [NaOH]0.44 at 298 K, with a low activation energy of 22.9 kJ mol−1. Molybdenum's promoting effect prevented significant deactivation of the cobalt catalyst, ensuring complete NaBH4 conversion to H2 and good stability over multiple cycles.

Development of a gel formulation with pomegranate peel extract (Punica granatum L.) for antimicrobial and wound healing action

The aim of this study was to evaluate the feasibility of producing a gel from pomegranate peel extract for topical application, specifically for antimicrobial and wound healing purposes. Initially, the dry crude pomegranate peel extract (DCPPE) was analyzed for its phenolic profile using HPLC and by determining the total phenolic content (TPC), and total antioxidant activity (TAA). Carbomer-based gels were prepared and subjected to antimicrobial susceptibility tests to determine the optimal concentration of DCPPE (1.25 %, 2.5 %, and 3.75% w/w) in the formulations. Then, gel was produced in larger quantities and submitted to physicochemical and microbiological tests after being stored at room temperature or under refrigeration for 90 days. Gallic acid, ellagic acid, and punicalagin A and B were identified in DCPPE. The TPC was measured at 61.92 mg of gallic acid equivalent per gram (mg.GAE.g−1) and the TAA was 93.8 % (solution at 40 µL.mL−1), demonstrating superiority over butylhydroxytoluene (BHT) and gallic acid solutions at equivalent concentrations. Antimicrobial susceptibility tests indicated a significant difference (p < 0.05) for the 2.5% w/w DCPPE gel against Staphylococcus aureus and Candida albicans, which was the chosen concentration. Over a 30-day period under both storage conditions, there was no significant difference in pH values, and the reduction of TPC in the refrigerated formulation was <10 %, indicating good stability. Furthermore, the in vitro antimicrobial activity of the gel remained effective against all tested strains. These results suggest that the medicinal carbomer-based gel with DCPPE at 2.5% w/w has potential as a pharmaceutical form for antimicrobial and wound healing purposes. The utilization of DCPPE as a pharmaceutical bio-input for the gel is a sustainable approach to valorizing pomegranate peel biowaste.

Establishment and evaluation of haloalkane dehalogenase tagged α1A-adrenergic receptor chromatography

Receptor chromatography is an efficient analytical technique that combines the high separation ability of chromatography with the high specificity of receptors for drug recognition. In addition, this technique offers the advantages of active recognition, online separation, and convenient multidimensional target tracking. This strategy allows target active ingredients in complex systems, such as traditional Chinese medicines, to be efficiently screened and accurately identified. Furthermore, the interactions between ligands and immobilized proteins can be studied. To avoid a loss in function, receptor chromatography requires efficient, mild, and simple immobilization methods that do not damage the structure of the immobilized receptors. Improvements in the activity, stability, and ligand-recognition specificity of immobilized functional proteins can be achieved by selecting appropriate immobilization conditions. Notably, the protein immobilization method is not only closely related to the recognition ability of receptor chromatography but also determines the accuracy of the technique. Common methods for immobilizing functional proteins include physical adsorption, chemical reactions, biological affinity reactions, and click chemistry. Despite being easy to operate under mild reaction conditions, these methods have shortcomings, including poor reaction specificity and the necessity of using high-purity functional proteins to prepare chromatography columns. Maintaining the high activity of immobilized receptors and ensuring excellent identification and separation abilities are key challenges in the further development of receptor chromatography. In this work, these issues were addressed by introducing a specific bioorthogonal reaction involving haloalkane dehalogenase (Halo) and 6-chlorohexanoic acid for the immobilization of the α1A-adrenergic receptor (α1A-AR). Specifically, Halo-α1A-AR was immobilized on the surface of 6-chlorohexanoic acid-modified aminopropyl silica gel in one step. The stationary phase with immobilized Halo-α1A-AR was characterized using scanning electron microscopy. Moreover, the activity of the Halo-α1A-AR chromatographic column was evaluated using specific ligands (terazosin hydrochloride, phentolamine mesylate, tamsulosin hydrochloride, and urapidil) and nonspecific ligands (yohimbe and metoprolol) for α1A-AR. Halo-α1A-AR was successfully immobilized on the silica gel surface with good stability over 30 days, and the Halo-α1A-AR chromatographic column exhibited good ligand-recognition activity. The nonlinear chromatography results indicated that prazosin hydrochloride, terazosin hydrochloride, and urapidil interacted with immobilized Halo-α1A-AR through one type of binding site, with association constants of 3.85×105, 5.00×105, and 5.90×105L/mol, respectively. In contrast, phentolamine mesylate and tamsulosin hydrochloride interacted with immobilized Halo-α1A-AR through two types of binding site. The association constants with the high- and low-affinity binding sites were 3.12×106 and 6.01×105L/mol, respectively, for phentolamine mesylate and 9.98×105 and 0.21×105L/mol, respectively, for tamsulosin hydrochloride. Compared with the traditional carbonyldiimidazole method, the immobilization method developed in this work did not require receptor purification and thus minimized the loss of receptor activity. The affinity constants obtained with immobilized Halo-α1A-AR were consistent with the values determined for receptor-ligand binding in solution, indicating that the Halo-α1A-AR chromatography column is suitable for studying drug-protein interactions. This approach also provides a foundation for the efficient screening and accurate determination of target active ingredients in complex systems.

Rapid and selective removal of bisphenol S from environmental samples by surface-imprinted polymer synthesized based on metal-organic framework MIL-101(Cr)

In this study, a novel, surface-imprinted polymer (MIL-101@MIP) was successfully synthesized using the metal-organic framework MIL-101(Cr) with a large specific surface area as a carrier, which achieved rapid and selective removal of bisphenol S (BPS) from environmental samples. The structure and morphology of MIL-101@MIP were characterized using SEM, XPS, FTIR, TGA, BET, and XRD techniques. The results show that MIL-101@MIP has rough surface morphology and good thermal stability. The large specific surface area (1251.6 m2 g-1) of MIL-101@MIP provides more imprinting sites in MIL-101@MIP; thus, the maximum adsorption capacity of BPS reached 87.76mgg-1 with good imprinting factor 2.08, and equilibrium was achieved in only 10min. Moreover, the process of BPS adsorption onto MIL-101@MIP followed the pseudo-second-order kinetics and Langmuir isothermal adsorption models. In addition, the MIL-101@MIP was utilized as an adsorbent for a solid phase extraction column to determine BPS in seven environmental samples using HPLC, achieving recovery of 89.20–105.78%. The developed MIL-101@MIP is a promising and efficient adsorbent for rapid and selective removal of BPS from the environment.

Electrochemical degradation of m-nitrophenol using an innovative zeolite modified PbO2 anode: Electrode characterization, influence factors and degradation mechanism

In this study, a zeolite-doped PbO2 (Zeo-PbO2) anode was fabricated via electrodeposition technology for electrochemical oxidation of m-nitrophenol (m-NP). The results of characterization revealed that doping zeolite efficiently promoted the oxygen evolution potential and active sites of PbO2 anode, thereby higher performance to generate •OH radical and degrade the m-NP. The •OH radical was confirmed to be the primary contributor to the electrochemical oxidation of m-NP by scavenging tests. Thus, the effect mechanism of current density, supporting electrolyte, and initial pH on the removal of m-NP in the electrochemical oxidation process was explored by the generation of •OH radicals at different conditions. Based on the vulnerable sites of m-NP to the attack of •OH radical supposed by the theoretical calculation and degradation intermediates identified by GC-MS and IC, the degradation pathways of m-NP in the electrochemical oxidation process were speculated. Besides, the good recyclability and stability of Zeo-PbO2 anode were exhibited in consecutive m-NP degradation, •OH generation experiments, and accelerated life tests.

Enhanced peroxymonosulfate activation for effective norfloxacin degradation by sepiolite-based FeCo layered double hydroxide composite

In this study, the FeCo layered double hydroxide/Sepiolite composite was successfully synthesized by a water bath approach which exhibited outstanding norfloxacin (NOR) degradation performance in presence of peroxymonosulfate (PMS). The reaction rate constant in the FeCo-LDH/Sepiolite/PMS system was 0.1644min-1, which was around 1.78 times greater than that in the FeCo-LDH/PMS system. The introduction of the sepiolite carrier, which led to an increase in specific surface area and pore volume, was principally responsible for the considerable improvement in PMS activation efficiency. Moreover, the composite presented good stability and reusability. According to the results of the electron paramagnetic resonance (EPR) and quenching tests, the predominant reactive species in the FeCo-LDH/Sepiolite/PMS/NOR system were SO4•- and 1O2. Furthermore, possible NOR degradation pathways and catalytic mechanism were proposed. In summary, our research provised new ideas in the synthesis of promising mineral based PMS catalyst for wastewater treatment.

Laser-induced CdS/TiO2/graphene dual photoanodes for ratiometric self-powered photoelectrochemical sensor: an innovative approach for aflatoxin B1 detection.

A ratiometric self-powered photoelectrochemical sensor based on laser direct writing technology was constructed to address the problem that the conventional single-signal detection mode was susceptible to the influence of instrumentation and environmental factors, which interfered with the detection results. Laser-induced CdS/TiO2/Graphene was prepared as dual photoanodes (PA1 and PA2), which were controlled by multiplexed switches to form a photocatalytic fuel cell with Pt cathode. By modifying the aptamer of aflatoxin B1 (AFB1) on the photoanode surface, the target was specifically captured to the electrode surface to form a biological complex, which increased the steric hindrance and affected the electron transfer, thus reducing the output signal of the sensor. Targets with different concentrations were incubated on the surface of PA1, and targets with fixed concentrations were incubated on the surface of PA2. Under the control of the multiplex switch, the output signals of the two photoanodes were recorded, and the ratio of these two signals was used as the basis for the quantitative detection of AFB1. The sensor output was linearly increasing with the logarithm of AFB1 concentration from 1.0 to 150ngmL-1 and the detection limit was 0.0974ngmL-1. Additionally, this method had good stability, fast response, and good selectivity to real samples, providing an effective method for food safety monitoring.

Lead-Free Cs2AgBiBr6/TiO2 S-Scheme Heterojunction for Efficient Photocatalytic Antibiotic Rifampicin Degradation.

Exploring efficient and stable halide perovskite-based photocatalysts is a great challenge due to the balance between the photocatalytic performance, toxicity, and intrinsic chemical instability of the materials. Here, the environmentally friendly lead-free perovskite Cs2AgBiBr6 confined in the mesoporous TiO2 crystal matrix has been designed to enhance the charge carrier extraction and utilization for efficient photocatalytic rifampicin degradation. The as-prepared Cs2AgBiBr6/TiO2 catalyst was stable in air for over 500 days. An S-scheme heterojunction was formed between the (004) plane of Cs2AgBiBr6 and the (101) plane of TiO2 through the Bi-O-Br bonds. The built-in electric field at the interface efficiently promoted the photoinduced charge separation and carrier extraction. The Cs2AgBiBr6/TiO2-200 showed a 92.83% degradation efficiency of rifampicin within 80 min under simulated sunlight illumination (AM 1.5G 100 mW cm-2). This work offers an effective way for the construction of halide perovskite-based photocatalysts with high photocatalytic performance, good stability, and low toxicity simultaneously.

Nanoprobe Based on Novel NIR-II Quinolinium Cyanine for Multimodal Imaging.

NIR-II imaging has the advantages of high sensitivity, spatiotemporal resolution, and high penetration depth, thereby serving as a potential alternative to conventional imaging methods. Herein, a novel NIR-II dye IR-1010 (λex/λem = 1010/1058nm) is reported with high quantum yield (3.08%) and good stability, by incorporating p-methoxyphenyl groups into a quinolinium cyanine dye. Then a multifunctional nanoprobe, termed IUFP NPs, is developed by the incorporation of upconversion (UC) nanoparticles (NPs), perfluoro-15-crown-5-ether (PFCE), and IR-1010, to display the novel performance of multimodal imaging. Under the single-wavelength excitation (980nm), IUFP NPs simultaneously emit the NIR-II fluorescence of IR-1010 and visible UC luminescence of UCNPs, and thus realize the UC imaging for cells, and NIR-II fluorescence/photoacoustic/19F magnetic resonance imaging for blood vessels, lymph nodes and tumor in mice. This work affords a novel approach to NIR-II dyes and a general strategy for the design of multimodal imaging probes.

Surface Property Regulation of a Magnetron-Sputtered NiOx Hole Transport Layer for High-Performance Inverted Perovskite Solar Cells.

The inverted perovskite solar cells (PSCs) are gaining increasing attention recently for their unprecedented advantages, such as better integration with tandem and flexible designs, negligible hysteresis, good operational stability, and compatibility with commercially scalable fabrication approaches. Nickel oxide (NiOx) films prepared by magnetron sputtering technology exhibit excellent scalability and reproducibility, which could well meet the requirements of the large-scale production of inverted PSCs. However, NiOx prepared by vacuum methods generally has fewer surface hydroxyl groups, deteriorating the wettability and damaging the interface contact with the perovskite. Particularly, the Ni3+ defects on the NiOx surface could lead to unfavorable redox reactions with organic cations in the perovskite under high temperatures, promoting the rapid degradation of the perovskite. Thus, surface regulation of sputtered NiOx is imperative for high-performance PSCs. Herein, 4-(trifluoromethyl) phenylcarbamate hydrochloride (TFFA) was used to regulate the surface properties of sputtered NiOx. The strongly electronegative F ions in TFFA passivated the Ni3+ defects on the NiOx surface, suppressed unfavorable interface reactions, and improved charge recombination. The polar ammonium functional group was used to adjust the surface energy of NiOx, thereby improving the wettability and optimizing the crystallization kinetics of the perovskite. As a result, the power conversion efficiency (PCE) of PSCs reached 22.76%, which was among the highest PCEs reported for sputtered NiOx-based inverted PSCs to date. Moreover, the unencapsulated target devices exhibited better stability, maintaining over 85% of the initial PCE after aging for approximately 1200 h in a N2 environment. Our achievements pointed out a practical strategy for enhancing the performance of sputtered NiOx-based inverted PSCs, which could potentially accelerate the development and application of large-area PSCs.

Polypod Carboxylic Acid-Rare Earth Complex with High Cyclic Stability for Nitrobenzene Compound Detection.

The 5',5''-bis(4-carboxyphenyl)-[1,1':3',1'':3'',1'''-quaterphenyl]-4,4'''-dicarboxylic (H4L1) ligand has a large conjugated rigid planar structure and good absorption of ultraviolet radiation, which can provide effective "antenna effect". However, rare earth complexes using H4L1 as the sole ligand have not been reported. In this paper, rare earth Eu was combined with H4L1 ligand to produce organic rare earth composite L1-Eu by solvothermal synthesis method. It was found through fluorescence spectroscopy that the emission of L1-Eu complex has a linear response to nitrobenzene compounds. The L1-Eu composite material has a low detection limit for nitrobenzene compounds, with detection limits of 0.910, 8.401, 24.510, and 8.171 µM for nitrobenzene, o-nitrophenol, m-nitrophenol, and p-nitrophenol, respectively. Further more the L1-Eu complex can sensitively respond to nitrobenzene compounds while resisting interference from common metal ions and organic solvents. In particular, L1-Eu composite material has good stability and recyclability. Therefore, L1-Eu composite material can serve as a fluorescent probe for specific detection of nitrobenzene compounds. We believe that the L1-Eu complex provides a new method for fluorescence detection of nitrobenzene compounds.

Zinc Tellurium with Anionic Vacancies Anchored on Ordered Macroporous Carbon Skeleton Enabling Accelerated Polysulfide Conversion for Lithium-Sulfur Batteries.

Lithium-sulfur batteries (LSBs) showcase great promise for large-scale energy storage systems, however, their practical commercialization is seriously hindered by the sluggish redox reaction kinetics and detrimental shuttle effect of soluble polysulfides. Herein, small ZnTe1- x nanoparticles with anionic vacancies firmly anchored on 3D ordered macroporous N-doped carbon skeleton (3DOM-ZnTe1- x@NC) are elaborately constructed as a high-efficiency electrocatalyst for LSBs. The ordered macroporous carbon skeleton not only greatly increases the external surface area to expose sufficient active sites but also facilitates the electrolyte penetration. Additionally, the experimental studies combined with theoretical calculations confirm the presence of Te vacancies optimizes the electronic structure to enhance the intrinsic catalytic activity and chemical absorption. Consequently, LSBs assembled with the 3DOM-ZnTe1- x@NC modified separators exhibit high specific discharge capacity, as well as superior rate performance and good long-term cycling stability. Even under a high sulfur loading of 6.5 mg cm-2 and lean electrolyte, an impressive areal capacity of 5.28 mAh cm-2 is achieved at 0.1C after 100 cycles. More significantly, the 3DOM-ZnTe1- x@NC based pouch cells are also fabricated to demonstrate its potential for practical applications. This work highlights that the rational combination of 3DOM architecture and vacancy engineering is important for designing advanced Li-S electrocatalysts.

Colorimetric and Fluorimetric Detection of Fe(III) Using a Rhodamine-Imidazole Hydrazone Based Chemosensor: Photophysical Properties, DFT, TGA, and DSC Studies.

Rhodamine-imidazole hydrazones (RIH-1 & RIH-2) based chemosensors have been synthesized. These are characterised and evaluated by FT-IR spectroscopy, 1H-NMR, 13C-NMR, LCMS, absorption and fluorescence spectroscopy. These chemosensors exhibit enhanced sensitivity and selectivity in detecting the biologically significant Fe3+ metal ion through both colorimetric and fluorescence changes. The optical properties have been investigated using binary acetonitrile-water (7:3 v/v) semi-aqueous solution. The probe RIH-1 can be deployed as a fluorescent and colorimetric probe for the detection of Fe3+ ion. It shows an absorption band at 559nm and an intensity band at 579nm increasing up to 50-fold with the increase in the concentration of Fe3+ with the detection limit as low as 11nM. In the visible light, RIH-1 helps in the detection of Fe3+ ion through the naked eye, while the addition of Fe3+ to the probe RIH-1 results in a colour change from colourless to pink. This is primarily due to the opening of the lactone ring in RIH-1. Notably, RIH-1 probe displays a high quantum yield of 0.51, after binding with Fe3+ ions. Indeed, it has been found that sensor RIH-1 is very effective in sensing Fe3+ ions through both fluorescence based and visual detection methods. Additionally, DFT studies of these chemosensors have been evaluated, TGA and DSC analysis showed good thermal stability.

Electrolytic growth of phenyl-modified silica isoporous membrane for non-polar extraction and electrochemical detection of pentachloronitrobenzene.

A phenyl-modified silica isoporous membrane (Ph-SIM) was prepared on the indium-tin-oxide (ITO) electrode using the electrochemically assisted self-assembly (EASA) method. The resulting Ph-SIM preserved vertically ordered nanochannels while exhibiting outstanding hydrophobicity due to the incorporation of phenyl groups within the nanochannels. As a result, the Ph-SIM/ITO sensor exhibited a remarkable affinity for PCNB extraction through hydrophobic interactions, leading to high detection sensitivity. The electrochemical response showed a linear enhancement with the logarithmic concentration of PCNB ranging from 0.1 to 20.0µM, and the limit of detection was 4.64nM. Practical results demonstrated that the Ph-SIM/ITO sensor possessed good anti-fouling capability and robust stability, making it a promising candidate for portable detection of non-polar contaminants.

Identification and characterization of a novel polyamide hydrolase

The widespread use of non-naturally degradable plastics is causing increasingly serious harm to the environment. Reducing plastic pollutants has become the core of ecological and environment management. Biological methods such as enzymes demonstrate advantages in depolymerizing plastics with mild reaction conditions and recycling of depolymerization products. However, there are few reports on the biological depolymerization of polyamide plastics. In this study, by using 4-nitropropionanilide as the model substrate, we screened against our plastic depolymerase library and obtained a Meiothermus ruber-derived enzyme (MrABH) that can hydrolyze the polyamide bond. We expressed this enzyme in Escherichia coli and purified the protein by affinity chromatography. Furthermore, we investigated the catalytic properties, enzymatic properties, and catalytic products of this enzyme with polyamide as the substrate. MrABH had good stability at pH 8.0-10.0, with the optimal performance at pH 9.0 and 30 ℃. The catalytic performance of this enzyme for ester bonds and amide bonds was similar. MrABH can catalyze the depolymerization of PA6 and PA66 to produce monomers and oligomers, demonstrating the potential to be used in the depolymerization and recycling of polyamide.

First Alliance of Pyrazole and Furoxan Leading to High-Performance Energetic Materials.

Nitrogen heterocyclic scaffolds retain their leading position as valuable building blocks in material science, particularly for the design of small-molecule energetic materials. However, the search for more balanced combinations of directly linked heterocyclic cores is far from being exhausted and aims to reach ideally balanced high-energy substances. Herein, we present the synthetic route to novel pyrazole-furoxan framework enriched with nitro groups and demonstrate a promising set of properties, viz., good thermal stability, acceptable mechanical sensitivity, and high detonation performance. In-depth crystal analysis showed that the isomers having lower-impact sensitivity values in both types of regioisomeric pairs are those with the exocyclic furoxan oxygen atom being closer to the pyrazole ring. Owing to the favorable combination of high crystal densities (1.83-1.93 g cm-3), positive oxygen balance to CO (up to +13.9%), and high enthalpies of formation (322-435 kJ mol-1), the synthesized compounds show high calculated detonation velocities (8.4-9.1 km s-1) and excellent metal accelerating abilities. The incorporation of the 3-nitrofuroxan moiety increases the thermal stability (by ca. 20 °C) and decreases the mechanical sensitivity of target hybrid materials in both types of regioisomeric pairs. Simultaneously, the detonation performance of 3-nitrofuroxans is almost identical to that of 4-nitrofuroxans, highlighting the potential of the regioisomeric tunability in the future design of energetic materials.

An All-Solid-State Ti/RuOx pH Electrode Prepared Based on the Thermal Oxidation Method.

The development of all-solid-state precise pH electrodes holds significant importance in various fields, particularly in marine scientific research. To achieve this goal, we proposed a novel fabrication technique for an all-solid-state ruthenium oxide (Ti/RuOx) pH electrode. We thin-coated the RuCl3 precursor solution on a titanium wire substrate using a heat gun repeatedly and then calcined it in a mixture of Li2CO3 and Na2O2 at 400 °C to obtain a ruthenium oxide (RuOx) film. This RuOx film was subjected to acid treatment with dilute nitric acid, and a polytetrafluoroethylene heat shrink tube was wrapped around the non-RuOx film area. Finally, the RuOx film was fully immersed in a pH 4.00 buffer solution, finalizing the electrode preparation. The RuOx film exhibits a dense and regular conical morphology. The Ti/RuOx electrode demonstrates a good near-Nernstian response slope (e.g., -59.04 mV/pH at 25 °C), high linearity (e.g., R2 = 0.9999), rapid response (<1 s), low hysteresis (<3 mV), excellent reversibility, and good repeatability in the pH range of 2.00-10.00. After full hydration, the Ti/RuOx electrode shows a potential drift of 8.5 mV and a drift rate of approximately 0.27 mV/day over a period of 25 days, indicating good long-term stability. Furthermore, the Ti/RuOx electrode exhibits robust resistance against interference from various ions and low-concentration redox substances, ensuring a long storage life (at least 280 days), and high measurement accuracy (e.g., ± 0.02 pH units) for diverse water samples, including seawater, freshwater, and tap water. This study has evaluated the potential of the Ti/RuOx electrode as a reliable and accurate tool for pH measurements in marine scientific applications.

Direct Recycling of LixNi0.5Mn0.3Co0.2O2 from Production Scrap and End‐of‐Life Batteries using Solid‐State Relithiation

Direct recycling of Li‐ion battery cathodes offers a sustainable and potentially cost‐effective alternative to conventional methods, often involving complex chemical processes and significant material losses. This study focuses on the relithiation of cathode materials from quality control reject (QCR) and end‐of‐life (EoL) Li‐ion cells to restore their physical structure, morphology, and electrochemical performance. Two NMC532/graphite pouch cells from the same manufacturer were studied. QCR cells, stored under ambient conditions, experienced corrosion and degradation before recycling, while EoL cells were cycled to the end of life. The cells were disassembled, and the cathode materials were delaminated using NaOH solution, then relithiated with LiOH at 700°C for 15 hours in the air. Extensive characterization analyzed elemental composition, structural properties, thermal stability, and particle size distribution. Results indicated that relithiation successfully restored lithium content and improved the structural ordering and morphology of the cathode materials. The electrochemical performance of the relithiated cathodes exhibited good stability over 100 charge‐discharge cycles. The relithiated QCR samples achieved a capacity of 155.57 mAh g⁻¹, while EoL samples reached 152.53 mAh g⁻¹, comparable to pristine materials. This study highlights relithiation's potential to extend the lifecycle of Li‐ion cathodes, contributing to a more sustainable circular economy for battery materials.