Gas Sensors Research Articles

Low-Power Chemiresistive Gas Sensors for Transformer Fault Diagnosis.

Dissolved gas analysis (DGA) is considered to be the most convenient and effective approach for transformer fault diagnosis. Due to their excellent performance and development potential, chemiresistive gas sensors are anticipated to supersede the traditional gas chromatography analysis in the dissolved gas analysis of transformers. However, their high operating temperature and high power consumption restrict their deployment in battery-powered devices. This review examines the underlying principles of chemiresistive gas sensors. It comprehensively summarizes recent advances in low-power gas sensors for the detection of dissolved fault characteristic gases (H2, C2H2, CH4, C2H6, C2H4, CO, and CO2). Emphasis is placed on the synthesis methods of sensitive materials and their properties. The investigations have yielded substantial experimental data, indicating that adjusting the particle size and morphology structure of the sensitive materials and combining them with noble metal doping are the principal methods for enhancing the sensitivity performance and reducing the power consumption of chemiresistive gas sensors. Additionally, strategies to overcome the significant challenge of cross-sensitivity encountered in applications are provided. Finally, the future development direction of chemiresistive gas sensors for DGA is envisioned, offering guidance for developing and applying novel gas-sensitive sensors in transformer fault diagnosis.

Comparison of Gas-sensitive response of three metal-doped GaNNT with Pb, Pd and Pt after adsorption of hazardous gases

In this paper, we comparatively analyze the gas-sensing ability of Pb, Pd and Pt metal-doped GaNNT (M-GaNNT) materials for the hazardous H2S, SO2, NH3 and Cl2 gases. The adsorption structure, adsorption energy (Eads), density of states (DOS), differential charge density and frontier molecular orbital of the M-GaNNT adsorbed hazardous gas have been studied based on the density functional theory (DFT) calculations. The results show that the energy gap of Pb-GaNNT performs the largest change with an increasing percentage change of 358 % after the Cl2 adsorption compared with that before the Cl2 adsorption, while the energy gap of Pt-GaNNT has the least change with an average value of 20.8 %. The doping of metal atoms can effectively improve the gas-sensitivity of M-GaNNT, and the gas-sensitivity follows the order of Pb-GaNNT> Pd-GaNNT> Pt-GaNNT. The potential applications of M-GaNNT in gas sensor and adsorbent are then predicted through the analysis of the adsorption energy, sensitive response (SR) and recovery time (τ). Pb-GaNNT performs the best Cl2 gas removal since the largest Eads (-5.883 eV), largest SR (4.4 × 1015) and largest τ (2.9 × 1087s) can be determined for Cl2 adsorption on Pb-GaNNT. Furthermore, Pb-GaNNT is a good NH3 gas sensor since the related τ is only 2.9 s at 498 K, and a small Eads (-1.232 eV) with large SR (9.7 × 105) can be determined as well. The research findings in this paper provide a new sensor material option for both the detection and the removal of harmful gases, and the systematically theoretical method can spread to other systems.

1D MXenes: Synthesis, Properties, and Applications.

The fascinating properties and versatile nature of 2D MXenes have generated significant interest in the scientific community. This has led to extensive research on expanding these materials into 1D and 0D forms. This review investigates the synthesis, properties, and applications of 1D MXenes, elucidating their potential across various fields. 1D MXenes, including nanowires, nanoribbons, nanorods, and nanotubes, inherit the remarkable properties of their 2D counterparts while also exhibiting unique anisotropic characteristics that enhance their performance in various applications. The review explores various methods for synthesizing 1D MXenes and examines their structural, electronic, and optical properties. The transition from 2D to 1D results in MXenes that offer superior properties, which are advantageous for various next-generation systems. The increased aspect ratio and surface area of 1D MXenes broaden their usage in energy storage, photothermal therapy, oxygen evolution reactions (OER), hydrogen evolution reactions (HER), oxygen reduction reactions (ORR), microwave absorption, filtration membranes, gas sensors, metal detection, etc. The review also addresses the challenges associated with 1D MXenes, such as limited synthesis methods, scalable production, size customization, preservation of structural integrity, and stability. Furthermore, potential opportunities and future directions in the field of 1D MXenes have also been proposed.

A DFT investigation of monolayer InP: Effective toxic gas sensor with adsorption and optical response

An examination was conducted on the electronic and optical characteristics of gas (H2S, CO2, CO, SO2, and SO) adsorption on a monolayer of InP using first-principles calculations based on DFT. To identify the optimal and most sensitive adsorption site for the adsorbed gases, four initial adsorption sites were selected. Various aspects such as adsorption distance, charge densities, and adsorption energy were analyzed across different types of adsorption to determine the most favorable adsorption configurations. Our research indicates that InP monolayers can chemically adsorb CO2, CO, SO2, and SO, forming new bonds with these gas molecules. Furthermore, H2S can be physically absorbed onto InP with a high level of adsorption energy. The optical findings reveal that the presence of gas molecules alters the conductivity and optical properties of the InP monolayer, especially noticeable in the UV range. InP emerges as a suitable material for detecting CO2, CO, SO2, and SO due to its distinct characteristics.

Development of a Compact NDIR CO2 Gas Sensor for a Portable Gas Analyzer

A carbon dioxide (CO2) gas sensor based on non-dispersive infrared (NDIR) technology has been developed and is suitable for use in portable devices for high-precision CO2 detection. The NDIR gas sensor comprises a MEMS infrared emitter, a MEMS thermopile detector with an integrated optical filter, and a compact gas cell with high optical coupling efficiency. A dual-ellipsoid mirror optical system was designed, and based on optical simulation analysis, the structure of the dual-ellipsoid reflective gas chamber was designed and optimized, achieving a coupling efficiency of up to 54%. Optical and thermal simulations were conducted to design the sensor structure, considering thermal management and light analysis. By optimizing the gas cell structure and conditioning circuit, we effectively reduced the sensor’s baseline noise, enhancing the overall reliability and stability of the system. The sensor’s dimensions were 20 mm × 10 mm × 4 mm (L × W × H), only 15% of the size of traditional NDIR gas sensors with equivalent detection resolution. The developed sensor offers high sensitivity and low noise, with a sensitivity of 15 μV/ppm, a detection limit of 90 ppm, and a resolution of 30 ppm. The total power consumption of the whole sensor system is 6.5 mW, with a maximum power consumption of only 90 mW.

Decorated-Induced Oxygen Vacancy Engineering for Ultra-Low Concentration Nonanal Sensing: A Case Study of La-Decorated Bi2O2CO3.

La-decorated Bi2O2CO3 (BCO-La) microspheres are synthesized using a facile wet chemical strategy for sensing low-concentration nonanal (C9H18O) at room temperature. These BCO-La gas sensors are applied to evaluate agricultural product quality, specifically for cooked rice. The sensitivity of the BCO-6La sensor significantly surpassed that of the pure BCO sensor, achieving a response value of 174.6 when detecting 30ppm nonanal gas. Notably, the BCO-6La sensor demonstrated a faster response time (36 s) when exposed to 18ppm of nonanal. Additionally, the selectivity toward nonanal gas detection is higher (approximately 4-24 times) compared to interfering gases (1-octanol, geranyl acetone, linalool, hexanal, 2-pentyfuran, and 1-octen-3-ol) during cooked rice quality detection. The gas sensing mechanism and the factors contributing to the enhanced sensing performance of the BCO-La microspheres are demonstrated through in situ FT-IR spectra and DFT analysis while the realistic detection scenario is carried out. In a broader context, the reported sensors here represent a novel platform for the detection and monitoring of gases released by agricultural products during storage.

First-principles study of O3 molecule adsorption on pristine, N, Ga-doped and -Ga-N- co-doped graphene

The adsorption of O3 molecules (ozone) on graphene, N-doped graphene, Ga-doped graphene, and -Ga-N- co-doped graphene with an emphasis on O3 detection was examined in this work. The physical characteristics of -Ga-N-co-doped graphene are significantly altered upon O3 adsorption, which makes it a suitable choice for O3 detection molecular sensors. The interaction between the O3 molecule and the adsorbent is explained on the basis of their adsorption energy, adsorption distance and charge transfer. It was found that the adsorption of ozone molecules on the -Ga-N- co-doped graphene was more favorable in energy than that on the pristine one, representing the superior sensing performance of -Ga-N- co-doped system. In our work, we estimated the charge transfer between the O3 molecule and doped graphene nanostructures based on Mulliken population analysis. The calculated adsorption energy value shows the ozone molecule more firmly adsorbs on the surface of -Ga-N- co-doped graphene nanostructures (Eads = –1.74 eV) than that of pristine graphene (Eads = –0.41 eV), deriving from a stronger covalent bond between the ozone molecule and the -Ga- N- co-doped graphene nanostructures. Our findings thus suggest that -Ga-N- co-doped graphene could be a highly efficient gas sensor device for O3 detection in the environment.

Sensing volatile organic compounds in aquatic samples: a review

ABSTRACT Volatile organic compounds (VOCs) are toxic and harmful to human health; thus, their detection in water samples is critical for ensuring safe drinking water and protecting public health. The aim of this review was to explore the various techniques available in the literature for detecting VOCs in water samples and discuss their features, advantages, and limitations in facilitating fast and rapid VOC analysis. Established techniques such as gas chromatography and mass spectrometry offer high sensitivity and selectivity but are often hindered by complexity and cost. In contrast, emerging technologies like microfluidic gas sensors and cantilever-based sensors provide portable and real-time monitoring capabilities, although they may be susceptible to matrix effects. Overcoming these challenges requires advanced sample preparation techniques and method optimization. Additionally, the integration of machine learning algorithms and nanotechnology shows promise for enhancing sensitivity and precision in the detection of VOCs. By overcoming these limitations and leveraging technological advancements, researchers can improve water quality monitoring and help protect the environment.

Adsorption and gas sensing properties of CH4, C2H2, and C2H4 dissolved gases in transformer oil on Pdn(n = 1–4)-doped WTe2 monolayers: A DFT study

This paper investigates the potential of palladium (Pd) and its clusters-doped tungsten ditelluride (WTe2) monolayer materials for the detection of dissolved gases (such as CH4, C2H2, and C2H4) in transformer oil. Density functional theory (DFT) was used to study the effect of Pdn (n = 1–4) doping on the gas sensing and adsorption properties of WTe2 monolayer materials. The results show that Pdn doping can significantly improve the adsorption capacity and gas sensing performance of WTe2 to these gas molecules, especially showing excellent performance in detecting acetylene and ethylene. Studies have shown that Pdn doping improves the electrical conductivity of WTe2, making it more suitable for the development of gas sensors. Through the calculation of state density, molecular orbital and charge density difference, the adsorption mechanism of Pdn-doped WTe2 monolayer to different gas molecules was revealed. This study provides a theoretical basis and guidance for the development of efficient sensor materials for fault gas detection in transformer oil. In conclusion, the proposed Pd-doped WTe2 monolayer demonstrates promising potential for detecting dissolved gases in transformer oil. Future work will focus on experimental validation and further optimization of the material’s sensitivity and selectivity towards other gas species.

Recent Advances in Structure Design and Application of Metal Halide Perovskite-Based Gas Sensor.

Metal halide perovskites (MHPs) are emerging gas-sensing materials and have attracted considerable attention in gas sensors due to their unique bandgap structure and tunable optoelectronic properties. The past decade has witnessed significant developments in the gas-sensing field; however, their intrinsic structural instability and ambiguous gas-sensing mechanisms hamper their practical applications. Herein, we summarize the recent advances in MHP-based gas sensors. The physicochemical properties of MHPs are discussed at first. The structure design, including dimension design and engineering design, is overviewed as well as their fabrication methods, and we put forward our insights into the gas-sensing mechanism of MHPs. It is believed that enhanced understanding of gas-sensing mechanisms of MHPs are helpful for their application as gas-sensing materials, and structure design can enhance their stability, sensing sensitivity, and selectivity to target gases as gas sensors. Subsequently, the latest developments in MHP-based gas sensors are summarized according to their different application scenarios. Finally, we conclude with the current status and challenges in this field and propose future perspectives.

Operation Temperature Effects on a Microwave Gas Sensor with and without Sensitive Material.

Microwave gas sensors have garnered attention for their high sensitivity and selectivity in the detection of volatile organic compounds (VOCs). However, traditional gas sensors generally rely on sensitive materials that degrade over time and are easily affected by the environment, compromising their stability and accuracy. This study proposes a microwave VOC gas sensor based on the condensation effect. The sensor adopts a novel design without sensitive materials, utilizing the condensation effect to detect acetone gas. The sensor system consists of a microwave sensor and a temperature control device. As the sensor temperature is lowered below the boiling point of acetone, the condensation of acetone gas on the sensor surface is achieved, enabling accurate detection of acetone gas. Experimental results indicate that the accumulated amount of acetone on the sensor surface is positively correlated with its response, with the maximum response of 3000 ppm acetone gas reaching 0.34 dB. Additionally, this study investigated the detection mechanism of the sensor after adding the sensitive material MXene and compared the performance of the sensor at different temperatures (-10 °C, 0 °C, and 60 °C). The results show that at -10 °C the sensor mainly captures acetone through physical adsorption, while at 25 and 60 °C, it primarily responds through chemical adsorption, with a maximum response of 0.29 dB. The VOC sensor based on the condensation effect without sensitive materials not only achieves the same sensitivity as traditional microwave sensors but also demonstrates stronger stability and anti-interference capabilities.

Single ZnO Nanowire for Electrical and Optical NO2 Gas Sensing: Origin of Reversible and Irreversible Gas Effects Investigated by Photoluminescence Spectroscopy.

In this work, the gas sensing properties of a single ZnO nanowire (NW) are investigated, simultaneously in terms of photoluminescence (PL) and photocurrent (PC) response to NO2 gas, with the purpose of giving new insights on the gas sensing mechanism of a single 1D ZnO nanostructure. A single ZnO NW sensing device was fabricated, characterized, and compared with a sample made of bundles of ZnO NWs. UV near-band-edge PL emission spectroscopy was carried out at room temperature and by lowering the temperature down to 77 K, which allows detection of resolved PL peaks related to different excitonic transition regions. Surface effects were observed in PL maps, considering different nano and microstructures. Electrical and optical measurements were acquired at the same time during the NO2 gas exposure, allowing for the comparison of PL and PC response times and signal recovery. During NO2 gas desorption, irreversible behavior in the surface-related and donor-acceptor pair (DAP) regions is interpreted as the effect of an initial transient when electronic transfer from the gas molecules to the bulk occurs through the ZnO NW surface which acts as a channel. To the best of our knowledge, this is the first work which investigates the simultaneous PL optical and PC electrical response signals of a single ZnO NW to gas exposure.

Continuous Microreactor‐Based Synthesis of SnO2 Nanoparticles for Sensor Applications

Tin oxide nanoparticles are well‐established materials with a wide range of applications, including optoelectronic devices and solid‐state gas sensors. Conventional synthesis methods of these systems are often based on batch processes. In this study, we compare batch and continuous synthesis methods for tin dioxide nanoparticles using precipitation and sol‐gel processes. For the continuous processes we applied the so called microjet reactor method. The nanoparticles were characterized by TEM, elemental analysis and XRD and exhibited particle sizes of 1.7‐3.0 nm and crystallite sizes of 1.7‐2.3 nm, consisting of tetragonal (P42/mnm) and orthorhombic (Pbcn) phases. We have evaluated different post‐synthesis purification methods to remove impurities such as chlorides and carbon‐hydrogen species. Each purification method exhibited unique advantages and side effects, providing insight into selecting the most appropriate method for specific applications. We also demonstrated the potential of these SnO2 nanoparticles as ethanol gas sensing materials and compared their performance with a commercial sensor.

Wearable Inorganic Oxide Chemiresistor Based on Flexible Al2O3-Stabilized ZrO2 Ceramic Sponge Substrate for NO2 Sensing.

Wearable gas sensors, possessing the advantages of high sensitivity, excellent flexibility, high permeability, low weight, and workability at ambient conditions, hold great promise for real-time health monitoring and early warnings of poisonous gases. However, obtaining high-performance wearable gas sensors utilizing the current well-developed inorganic semiconductor oxide sensing materials is still very limited due to their fragile and rigid nature. Herein, a newly designed wearable gas sensor based on an all-inorganic ASZ (Al2O3-stabilized ZrO2)/ZnO/SnO2 nanofibers is introduced for the first time. The flexible ASZ ceramic sponge substrate (with a Young's modulus of 4.15 MPa) and ultrathin ZnO/SnO2 sensing layer endow the wearable gas sensor with promising properties such as super flexibility (with a bending radius of 5 mm), high gas permeability, and low weight. Furthermore, driven by UV light irradiation, this all-inorganic wearable sensor also demonstrates a stable NO2 sensing response under different bending states at room temperature, which enables the gas sensor to be more compatible with wearable sensing applications. This work offers a general method to achieve a high-performance wearable gas sensor based on inorganic materials and provides new insights into their potential in wearable gas-sensing applications.

UV-assisted fluctuation-enhanced gas sensing by ink-printed MoS2 devices

In this work, MoS2 flakes were printed on ceramic substrates and investigated toward 1–10 ppm of nitrogen dioxide (NO2), 2–12 ppm of ammonia (NH3), and 2–12 ppm acetone (C3H6O) under UV light (275 nm). The structure of overlapping MoS2 flakes and UV light assistance affected high responsivity to NO2 when DC resistance was monitored, and superior sensitivity to NH3 was obtained from the low-frequency noise spectra. MoS2 exhibited response and recovery times in hundreds of seconds and stability throughout the experiments conducted within a few months. MoS2 sensor exhibited a resistance drift during the detection of a specific relaxation time. Subtracting the baseline burden with exponential drift exposed the direction of changes induced by oxidizing and reducing gases and reduced DL to 80 ppb, 130 ppb, and 360 ppb for NO2, NH3, and C3H6O, respectively. The fluctuation-enhanced sensing (FES) revealed that the adsorption of NO2 on MoS2 decreases the noise intensity, whereas adsorbed NH3 increases the fluctuations of current flowing through the sensor, and these changes are proportional to the concentration of gases. The noise responses for NO2 and NH3 were opposite and higher than DC resistance responses with subtracted baseline (an increase of 50% for 10 ppm of NO2 and an increase of more than 600% for 12 ppm of NH3), showing that FES is a highly sensitive tool to detect and distinguish between these two gases. This way, we introduce a simple and low-cost method of gas sensor fabrication using ink-printed MoS2 and the possibility of enhancing its sensitivity through data processing and the FES method.

Susceptible Detection of Organic Molecules Based on C3B/Graphene and C3N/Graphene van der Waals Heterojunction Gas Sensors.

Constructing van der Waals (vdW) heterostructures is a prospective approach that is essential for developing a new generation of functional two-dimensional (2D) materials and designing new conceptual nanodevices. Using density-functional theory combined with a nonequilibrium Green's function approach allows for the theoretical and systematic exploration of the electronic structure, transport properties, and sensitivity of organic small molecules adsorbed on 2D C3B/graphene (Gra) and C3N/Gra vdW heterojunctions. Calculations show the metallic properties of C3B/Gra and C3N/Gra after the formation of heterojunctions. Interestingly, the heterojunctions C3B/Gra (C3N/Gra) for the adsorption of small organic molecules (C2H2, C2H4, CH3OH, CH4, and HCHO) at the C3B (C3N) side are sensitive to the chemisorption of C2H2 and C2H4. Similarly, the Gra/C3B is chemisorbed for both C2H2 and C2H4 when adsorbed on Gra side, while it is only chemisorbed for C2H2 in Gra/C3N. Interestingly, all heterojunctions on different sides are physisorbed for CH3OH, CH4, and HCHO. Furthermore, the calculated I-V curves demonstrate that the devices based on the adsorption of C2H2 and C2H4 at each side of the heterojunction have remarkable anisotropy, in with the current being considerably greater in the zigzag direction than in the armchair direction. More specifically, with C2H2 adsorbed on the Gra side, the sensitivity along the armchair direction is up to 85.0% for Gra/C3B and close to 100% for Gra/C3N. This study reveals that C3B/Gra (C3N/Gra) heterojunctions with high selectivity, high anisotropy, and excellent sensitivity are highly prospective 2D materials for applications, which further contributes new insights into the development of future electronic nanodevices.

Exploration of Volatileomics and Optical Properties of Fusarium graminearum-Contaminated Maize: An Application Basis for Low-Cost and Non-Destructive Detection.

Fusarium graminearum (F. graminearum) in maize poses a threat to grain security. Current non-destructive detection methods face limited practical applications in grain quality detection. This study aims to understand the optical properties and volatileomics of F. graminearum-contaminated maize. Specifically, the transmission and reflection spectra (wavelength range of 200-1100 nm) were used to explore the optical properties of F. graminearum-contaminated maize. Volatile organic compounds (VOCs) of F. graminearum-contaminated maize were determined by headspace solid phase micro-extraction with gas chromatography-tandem mass spectrometry. The VOCs of normal maize were mainly alcohols and ketones, while the VOCs of severely contaminated maize became organic acids and alcohols. The ultraviolet excitation spectrum of maize showed a peak redshift as fungi grew, and the intensity decreased in the 400-600 nm band. Peak redshift and intensity changes were observed in the visible/near-infrared reflectance and transmission spectra of F. graminearum-contaminated maize. Remarkably, optical imaging platforms based on optical properties were developed to ensure high-throughput detection for single-kernel maize. The developed imaging platform could achieve more than 80% classification accuracy, whereas asymmetric polarization imaging achieved more than 93% prediction accuracy. Overall, these results can provide theoretical support for the cost-effective preparation of low-cost gas sensors and high-prediction sorting equipment for maize quality detection.

(Invited) Development of Fiber-Optic Hydrogen Sensor Using Platinum-Supported Tungsten Trioxide-Silica Composite Film

A fiber-optic hydrogen gas sensor using a platinum-supported tungsten oxide-silica composite film was fabricated. This sensor utilizes the absorption of the evanescent field interaction in the hydrogen sensitive clad which was composed of WO3 and SiO2, coated on a silica core with sol-gel process. As a first step, transmission spectra of sensing film itself were measured. The transmittance of the sensitive film decreased in the range of wavelengths above about 500 nm after exposure to pure hydrogen, and the change in transmittance at 1300 nm was greater than that at 850 nm. Then, fiber optic sensor device was fabricated, and the amount of propagating light was measured. In the case of using the light source with a wavelength of 1300 nm, the sensitivity with respect to the hydrogen response was nearly twice and the response speed was faster, compared with those at 850 nm.

Construction of a novel Mott-Schottky heterostructure gas sensor g-C3N4/SnO2 with layered nanorods array for high-sensitivity acetone detection

Developing exhaled acetone sensors with high performance can be effectively applied to the medical diagnosis and the health monitoring. Herein, a two-dimensional (2D) layered graphitic carbon nitride (g-C3N4) with tunable electronic structure, abundant edge sites, and high stability is proposed, and it is further coupled with stannic oxide (SnO2) by one-step hydrothermal approach to construct a Mott-Schottky heterostructure with layered nanorods array. The exceptional response of the as-fabricated g-C3N4/SnO2 gas sensor to 50 ppm acetone at 100 °C is four times higher than that of the pristine SnO2 sensor. Additionally, the g-C3N4/SnO2 sensor’s remarkable selectivity, long-term stability against acetone gas, and detection limit of 250 ppb are exhibited. The unique hierarchical design and the Mott-Schottky heterostructure creation which validated by electrochemical study, may be in charge of the enhanced acetone sensing capabilities of g-C3N4/SnO2 gas sensor. This work will provide a concise and effective avenue to construct hierarchical composite with Mott-Schottky heterostructure for high-performance acetone gas sensor.

Convective assembly of silica colloidal particles inside photonic integrated chip-based microfluidic systems for gas sensing applications.

Optofluidics is a new field of modern science that stands at the interface of microfluidics and photonics and has good prospects for application in gas sensors. Microfluidics offers a promising platform for tuning and assembling monolayer structures that are used as sensitive layers for gas detection. Herein, we evaluate the concept of monolayer formation on a silicon nitride substrate enabling a surface coverage up to 59% through a microfluidic convective assembly and couple it with a photonic integrated chip to probe gas sensing performance.