Fixed Frequency Sliding Mode Controller Research Articles

Performance evaluation of transformerless photovoltaic inverter

ABSTRACT The instantaneous power of 1- solar photovoltaic system comprising of high-gain DC-DC converter and 1- photovoltaic inverter has a twice line frequency that creates the undesirable second order harmonic current. This paper provides topological changes in both DC-DC converter and DC-AC inverter to mitigate the undesirable second-order harmonic current. Re-boost converter is used instead of boost converter, and power decoupling-based 1- inverter is used for the inverter purpose. To provide adequate DC-link voltage, standard maximum power point tracking scheme is used. To control the output of inverter, fixed-frequency sliding mode controller is used that provides better response in steady state as well as transient state conditions.

Sliding Mode Input Current Control of the Synchronous DC-DC Buck Converter for Electro-Mechanical Actuator Emulation in More Electric Aircrafts

The main challenges of the input current control in synchronous DC-DC buck converters are the nonlinear model of the system, changes of the operating point in a wide range, and the need to use an input LC filter for current smoothing, which may result in the instability of the closed-loop system. In this paper, a step-by-step approach is developed for the design and improvement of a PI-feedforward closed-loop controller. It is shown that a linear PI controller cannot stabilize the closed-loop system properly during wide changes in model parameters, e.g., an equivalent series resistance of the input filter. To cope with the stability issues, a fixed-frequency sliding mode controller (SMC) has been developed in this paper for the implementation of an electro-mechanical actuator (EMA) emulator. Moreover, a systematic approach is proposed for controller tuning and the selection of the SMC’s gains. To achieve high power efficiency, high-frequency GaN switches are used for the practical implementation of the DC-DC converter. Despite large changes in the load current, the designed nonlinear controller can track the input current reference satisfactorily. Steady-state and dynamic responses of the proposed SMC are compared with conventional linear controllers. Considering the Lyapunov stability theorem, it is proved that the designed SMC can stabilize the closed-loop system in the entire utilizable domain. The proposed nonlinear SMC controller enjoys a very simple control law. Hence, despite having very high switching and sampling frequencies, it can be easily implemented. The experimental response of the designed synchronous DC-DC buck converter is evaluated experimentally by implementing the control strategy in a TMS320F28335PGFA DSP from Texas Instrument. Moreover, the comprehensive comparison of the proposed SMC controller and a PI-feedforward controller proved the superior performance of the developed closed-loop system, in terms of the transient time response, robustness, and stability of the EMA emulator.

A novel dynamic integral sliding mode control for power electronic converters.

The key characteristics of the sliding mode control (SMC) are the ability to manage unmodeled dynamics with rapid response and the inherent robustness of parametric differences, making it an appropriate choice for the control of power electronic converters. However, its drawback of changing switching frequency causes critical electro-magnetic compatibility and switching power loss issues. This paper addresses the problem by proposing a dynamic integral sliding mode control for power converters having fixed switching frequency. A special hardware test rig is developed and tested under unregulated 12.5-22.5 V input and 30 V output. The experimental findings indicate excellent controller efficiency under wide range of loads and uncertain input voltage conditions. In addition, the findings indicate that the closed-loop system is robust to sudden differences in load conditions. This technique provides an improvement of % in the rise time, % in the settling time and % in robustness of the controller as compared to conventional controllers. Furthermore, the comparison with the existing fixed-frequency sliding mode control techniques is presented in a tabular form.

Robust Sliding Mode Control of a Unipolar Power Inverter

The key issue in the practical implementation of the sliding mode (SM) control–based power inverter is the variable switching frequency. This variable switching frequency not only induces electromagnetic interference (EMI) noise, but also reduces the efficiency of the inverter, as the size of the inductor and capacitor does not alter in tandem with this variable frequency. In this context, fixed switching frequency–based SM control techniques are proposed; however, some of them are too complex, while others compromise the inherent properties of SM control. In this research, a fixed frequency SM controller is proposed, which is based on the novel low-pass filter extraction of the discontinuous control signal. This allows the technique to be implemented with fewer hardware components, thus reducing the complications of implementation, while maintaining the robustness and parametric invariance of SM control. A simulation-based comparison with an existing pulse width modulated (PWM) SM controller is presented as the benchmark. In comparison with the sigmoid function SM controller, an improvement of 50% in the settling time along with zero steady-state errors and a further 37% and 42% improvement in the undershoot and overshoot, respectively, is reported in the simulation. A hardware setup is established to validate the proposed technique, which substantiates the simulation results and its disturbance rejection properties.

Analysis of Fractional Order Sliding Mode Control in a D-STATCOM Integrated Power Distribution System

At present, the disturbances like the voltage fluctuations, resulting from the grid’s complexities and unbalanced load conditions, create severe power quality concerns like total harmonic distortion (THD) and voltage unbalance factor (VUF) of the grid voltage. Though the custom power devices such as distribution-static compensators (D-STATCOMs) improve these power quality concerns, however, the accompanying controller plays the substantial role. Therefore, this paper proposes a fractional-order sliding mode control (FOSMC) for a D-STATCOM to compensate the low power distribution system by injecting/absorbing a specific extent of the reactive power under disturbances. FOSMC is a non-linear robust control in which the sliding surface is designed by using the Riemann-Liouville ( RL ) function and the chattering phenomenon is minimized by using the exponential reaching law. The stability of FOSMC is evidenced by employing the Lyapunov stability criteria. Moreover, the performance of the proposed FOSMC is further accessed while doing its parametric variations. The complete system is demonstrated with a model of 400V, 180kVA radial distributor along with D-STATCOM under two test scenarios in MATLAB/Simulink environment. The results of the proposed controller are compared with the fixed frequency sliding mode control (FFSMC) and conventional proportional-integral (PI) control. The results validate the superiority of the proposed controller in terms of rapid tracking, fast convergence, and overall damping with very low THD and VUF.

A NOVEL BIDIRECTIONAL QUASI Z SOURCE INVERTER FOR ELECTRIC VEHICLE APPLICATIONS

The fixed frequency sliding mode control method for this project is a single-phase grid-connected LCL filtered quasi-Z-source inverter (QZSI). In the proposed method, smoothing is applied to the function of the sliding surface, thereby eliminating jitter and achieving a fixed switching frequency. The smoothing process is performed by passing the function of the sliding surface through a narrow boundary layer. To mitigate steady state errors due to smoothing, a PIC controller is used to handle current grid errors and determine the capacitor voltage reference required in the SMC. The DC output of the battery is converted to AC using a DC AC inverter after withstanding or increasing demand. The inverter function must change the DC input voltage to the desired voltage and voltage as the asymmetric AC output voltage achieved through the control branches of Quasi by using simple boost control technology.

Reducing Beat Frequency Oscillation in a Two-phase Sliding Mode-controlled Voltage Regulator Module

During static and dynamic loading conditions, voltage regulator modules (VRMs) are expected to provide regulated voltage with minimal ripple even at high current requirement. Compared to regular power supplies, VRMs repetitively experience high-frequency loading conditions that is greatly dependent on the software running in the processor utilizing them. In the scenario that when the transient load frequency is near the VRM’s switching frequency, high-magnitude and low-frequency oscillations are observed at the phase currents. This phenomenon is called the beat frequency oscillation. In this study, the sliding mode control principle is employed to both the voltage and current share loops of the VRM to reduce the phase currents’ beat frequency oscillations. A fixed frequency sliding mode controller is derived and extensively evaluated using the PSIM simulator. Our results show that while maintaining equal load sharing among VRMs at less than 5% sharing error and various types of loading conditions, the sliding mode controller can reduce the beat frequency oscillation phenomenon to 20 kHz at maximum with reduced peak current values. The output voltage is also regulated within the desired ± 1.65% band.

Reducing Beat Frequency Oscillation in a Two-phase Sliding Mode-controlled Voltage Regulator Module

During static and dynamic loading conditions, voltage regulator modules (VRMs) are expected to provide regulated voltage with minimal ripple even at high current requirement. Compared to regular power supplies, VRMs repetitively experience high-frequency loading conditions that is greatly dependent on the software running in the processor utilizing them. In the scenario that when the transient load frequency is near the VRM’s switching frequency, high-magnitude and low-frequency oscillations are observed at the phase currents. This phenomenon is called the beat frequency oscillation. In this study, the sliding mode control principle is employed to both the voltage and current share loops of the VRM to reduce the phase currents’ beat frequency oscillations. A fixed frequency sliding mode controller is derived and extensively evaluated using the PSIM simulator. Our results show that while maintaining equal load sharing among VRMs at less than 5% sharing error and various types of loading conditions, the sliding mode controller can reduce the beat frequency oscillation phenomenon to 20 kHz at maximum with reduced peak current values. The output voltage is also regulated within the desired ± 1.65% band.

Genetic algorithm assisted fixed frequency sliding mode controller for quadratic boost converter in fuel cell vehicle

This study presents the quadratic boost converter (QBC) as a power electronic interface between the fuel cell (FC) stack and the DC bus of the FC vehicle (FCV). QBC provides the high voltage gain to interface the low voltage, high current and non-linear FC stack to higher voltage DC bus of the proposed architecture. The output voltage of FC is variable and is a function of cell chemistry, load variations and atmospheric conditions. Therefore, a genetic algorithm assisted fixed frequency sliding mode controller (SMC) based two-loop control strategy is proposed and developed in this study. The accuracy of the control signal generated by the SMC depends on the accuracy of reference current generation. Therefore, genetic algorithm tuned proportional–integral controller is proposed to generate the ripple-free reference current generation which follows the load-side or source-side variations. Further, a control algorithm is integrated with SMC which uses the design constants such that the chattering amplitude is suppressed and generates the control signal with fixed frequency. Consequently, the dynamic performance of the proposed controller is compared in terms of the tracking error, control effort and sliding surface error. The extensive studies are carried out under different dynamic conditions to analyse the robustness of the proposed controller for QBC-based FCV.

Analysis of a Fourth-Order Step-Down Converter

This article proposes a nonisolated wider step-down conversion ratio dc–dc converter having minimum phase behavior at nominal operating condition, for point-of-load applications. Compared to existing quadratic/stacked buck converter variants, the proposed topology shows effective switch utilization at low output voltages, lesser ripple content in source current, and reduced voltage/current stress on components. Time-domain analysis is formulated to anticipate the steady-state converter performance and establish design equations for L–C components. The state-space average model is derived and linearized transfer functions are evaluated to subsequently design a fixed-frequency sliding-mode controller. Step-by-step design procedure is presented to fulfil sliding surface existence, reachability, and stability conditions. Equivalent control law devised in this scheme is duly constituted from source side inductor current dynamics and load voltage error information, so it provides simple realization as well as better transient response. The distinctive features of proposed converter are studied analytically and demonstrated through experimental measurements on a laboratory prototype.

Fixed frequency sliding mode control of renewable energy resources in DC micro grid

AbstractThe rising cost of fossil fuels, their high depleting rate and issues regarding environmental pollution have brought the attention of the researchers towards renewable energy technologies. Different renewable energy resources like wind turbines, fuel cells and solar cells are connected to DC micro grid through controllable power electronic converters. In presence of these diverse generation units, robust controllers are required to ensure good power quality and to regulate grid voltage. This paper presents a sliding mode control based methodology to address the above mentioned challenges. The proposed technique keeps the switching frequency constant so that electromagnetic compatibility (EMC) issues can be solved with conventional filter design. Parallel operation of converter in DC micro gird is considered. Chattering reduction and power quality improvement by harmonic cancellation is proposed. A scaled down hardware for unregulated 11.5 V to 17.5 V input and 24V output is designed and tested. The experimental results show good performance of the controller under different loads and uncertain input voltage conditions. Moreover, the results show the robustness of the closed loop system to sudden variations in load conditions. Furthermore, a significant improvement in power quality is achieved by harmonic cancellation of chattering in the output of the converters.

A Fixed-Frequency Sliding-Mode Controller for Fourth-Order Class-D Amplifier

Since the parasitic voltage ringing and switching power losses limit the operation of active devices at elevated frequencies; therefore, a higher-order inductor-capacitor (LC) filter is commonly used, which offers extended attenuation above the cutoff frequency and thus, improves the total harmonic distortion (THD) of the amplifier. This paper applies the concept of integral sliding-mode control to a fourth-order class-D amplifier. Two fixed-frequency double integral sliding-mode (FFDISM) controllers are proposed, where one uses the inductor current while the other involves the capacitor current feedback. Their equivalent control equations are derived, but from the realization viewpoint, the controller using the capacitor current feedback is advantageous and, therefore, is selected for final implementation. The performance of the proposed FFDISM controller for fourth-order GaN class-D amplifier is confirmed using simulation and experimental results.

Fixed Frequency Sliding Mode Control of Power Converters for Improved Dynamic Response in DC Micro-Grids

The rapid decrease in conventional energy resources and their harmful impact on the environment has brought the attention of the researchers towards the use of renewable energy technologies. The renewable energy systems are connected to Direct Current (DC) micro-grids via power electronic converters where the load conditions are unknown and network parameters are uncertain. These conditions call for the use of robust control techniques such as Sliding Mode Control (SMC) in order to regulate the grid voltage. However, SMC has a drawback of operating the power converter at variable switching frequency which results in degrading the power quality. This paper introduces a fixed frequency sliding mode controller that does not suffer from this predicament. A novel double integral type switching manifold is proposed to achieve voltage regulation of a DC micro-grid, in the presence of unknown load demands and un-modeled dynamics of the network. Rigorous mathematical analysis is carried out for the stability of the closed loop system and the technique is experimentally validated on position of a DC micro-grid using a specially designed test rig. For benchmarking purposes, a conventional Proportional Integral (PI) controller is also implemented. An improvement of 2.5% in rise time, 6.7% in settling time and reduction of voltage dip by 31.7% during load transaction is achieved as compared to the PI controller. The experiment confirms the hypothesis that fixed frequency SMC shows better performance than its counterpart in the phase of introduced disturbances.

Fixed-Frequency Sliding-Mode Control Scheme Based on Current Control Manifold for Improved Dynamic Performance of Boost PFC Converter

This paper deals with the switching regulation of boost power factor correction (PFC) converter under large and quick load fluctuation to ensure tight output voltage regulation and unity PF (UPF) at line side. In this sense, the sliding-mode control (SMC) technique based on current-controlled manifold is proposed. Input current distortion is limited even during light loading condition. In addition, the dead-zone issue related to light load near to the crossover of input current is resolved in this paper. To execute the proposed SMC algorithm, equivalent control approach is used for the selection of sliding coefficients, ensuring the system stability. The control operation manipulates both inner SM current controller to frame input current and an outer PI controller to maintain desired regulated output voltage. For experimental validation, a 500-W, 390 V/dc boost PFC prototype, controlled by dSPACE 1104 signal processor is framed. The presented simulation and experimental results infer that the proposed converter controller offers UPF, tight output voltage regulation, and percentage total harmonic distortion standard even under fluctuating load behavior. In this paper, the performance of the proposed control scheme is experimentally verified with different load behaviors and external references, which explains the robustness and effectiveness of the proposed system.

PWM-Based Sliding Mode Controller for Three-Level Full-Bridge DC-DC Converter that Eliminates Static Output Voltage Error

This paper proposes a pulse width modulation (PWM)-based sliding mode controller (SMC) for a full-bridge DC-DC converter that can eliminate static output voltage error. Hysteretic SMC in DC-DC converter does not have a fixed switching frequency, and applying hysteretic SMC to full-bridge converters is difficult. Fixed-frequency SMC, which is also called PWM-based SMC, based on equivalent control overcomes these shortcomings. However, the controller order reduction in equivalent control in PWM-based SMC causes static output voltage error. To resolve this issue, an integral item is added to the PWM-based SMC. Sliding mode coefficients are designed by applying a standard second-order system to the sliding mode surface. The effect of adding an integral item on the controller is analyzed, and an integral coefficient design method is proposed. Experiment results on a three-level full-bridge DC-DC converter verify the control scheme and design method proposed in this paper.

A Digital Current Control of Quasi-Z-Source Inverter With Battery

This paper presents a fixed frequency operating sliding mode (SM) current control method with fast response and improved stability. Different from the conventional SM control with variable switching frequency, the fixed-frequency SM controller is proposed to control the modulation index and shoot-through duty ratio of the voltage-fed quasi-Z-source inverter (qZSI), which will not increase the passive components and filter design difficulty. A large-signal dynamic model of the system has been established, which can be used for the system stability control in a wide operating range. By using linear approximation, the system small-signal model is also obtained to analyze the control system stability and transient response. Compared with the conventional current mode controller, the proposed SM controller can achieve faster response, lower current ripple and better stability for qZSI when the supply and load variation is large. Experimental results are presented to demonstrate the validity of the theoretical design and the effectiveness of the proposed controller.

Analysis and Modeling of an FFHC-Controlled DC–DC Buck Converter Suitable for Wide Range of Operating Conditions

To achieve the best optimized performance in terms of stability and dynamic behavior of power electronic converters, it is necessary to use a more advanced control technique and accurate mathematical model. This paper proposes a fixed-frequency hysteretic current (FFHC) controller that uses both sliding-mode control (SMC) technique and fixed-frequency current controller with a hysteresis band to achieve all properties of the variable structure controller. However, realizing such fixed-frequency sliding-mode controller using small-signal-averaged (SSA) model of the power converters and Utkin's equivalent control technique may not be valid for all conditions. We show that it can be applicable only when the fast-scale dynamics of the converter system is stable, which can be achieved successfully by analyzing the stability of the FFHC-controlled buck converter using Filippov method and Floquet theory. The regions of stability are then presented to show the domains of existence of nominal period-1 and higher periodic orbits in 2-D parameter space. We also demonstrate how to derive the equivalent control law from the modified tristate converter topology to design the controller. Finally, the experimental results are presented to validate the effectiveness of this hybrid FFHC controller.