Structure Of Films Research Articles

Atomistic insight into structure and properties of oxide films formed upon oxidation of Al–Mg alloys – reactive molecular dynamics study

Oxidation phenomena on metal surfaces can be advanced using atomistic modeling for the study of the structure and properties of the growing oxide films. Molecular dynamics investigations were performed to study thermal oxidation of single-crystal and polycrystalline Al–Mg alloys with low Mg content of up to 2.5 at. %. Structure, topological atom network and surface topography of the oxide films grown on Al–Mg surfaces at 300, 475 and 663 K are determined. Mg-content and temperature dependent oxide films developed on Al-Mg alloy substrates with two-phase oxide film formation as also confirmed experimentally. It is related with a gradual long-range order formation above 475 K for (Al,Mg)-oxide films, for which solid amorphous phase predominates over crystalline phase. The 1.12-nm-thick oxide films grown at 300 K are fully amorphous and build up from (Al, Mg)-oxide which the Al2O3 dominates. Increase of Mg coefficient confirms faster Mg diffusion to oxide/alloy interface at high oxidation temperature and the formation of MgO-like network. The presence of planar crystal defect (grain boundary, GB) into Al-Mg alloy substrate governs the kinetics of oxide film growth and its structure evolution. GB also compensate internal stresses during oxide film growth. Obtained results are in good agreement with experimental observations.

Morphology and spatial distribution of ordered domains in GaInP/GaAs(001) according to transmission electron microscopy

The structure of epitaxial films of the GaInP solid solution, in which ordering occurs, was studied using transmission electron microscopy. The films were grown by metalorganic vapor phase epitaxy on GaAs (001) substrates near the half-composition point. During the study, dark-field images obtained using superstructure reflections for cross-sectional and plan-view specimens of films were analyzed. The morphology and relative spatial arrangement of ordered domains have been determined. The phenomenon of spontaneous self-organization of regions with CuPt–B+ and CuPt–B– ordering near the surface was discovered, while in the bulk of the film the domains are uniformly located and mutually overlap each other. The effect of spatial separation of domains is associated with the lattice relaxation, leading to a change in the surface topology.

Deposition of Thin Films From HMDSO Utilizing the Vacuum UV Radiation From an Atmospheric Plasma

ABSTRACTThis study presents a source for studying thin‐film deposition utilizing vacuum UV (VUV) radiation from a remote argon or helium atmospheric plasma to initiate photochemistry in the precursor gas. We aim to assess how this radiation affects the deposition process and film structure while avoiding deposition inside the plasma source or particle formation. Deposition occurs where radiation interacts with the precursor and the growing film, as well as further downstream. The measured film properties clearly show that photon interaction with the film has a significant effect. Using hexamethyldisiloxane (HMDSO) as a precursor, we achieved nearly carbon‐free silicon dioxide () film growth due to photodesorption of hydrocarbons from the growing film, as confirmed by infrared spectra and positive ion mass spectrometry.

Analysis of Relationship between Microwave Magnetic Properties and Magnetic Structure of Permalloy Films

Changes in the microwave permeability of permalloy films with an increase in the film thickness are studied. Measurement data on the evolution of microwave permeability with film thickness are analyzed in the framework of a model for the film with a regular stripe domain structure and out-of-plane magnetic anisotropy. A correlation between the microwave magnetic properties and magnetic structure of permalloy films is established. It is demonstrated that the observed decrease in the ferromagnetic resonance frequency and the static permeability with a growth in the film thickness can ascribed to the appearance of perpendicular anisotropy and the formation of a stripe domain structure. The calculated dependences of the ferromagnetic resonance frequency and static permeability on the film thickness are in reasonable agreement with the measurement results. Based on the analysis of these dependences, the domain width in the permalloy films is estimated. It is found that for thick permalloy films, the domain width is of the order of the film thickness. The results obtained may be useful for high-frequency applications of soft magnetic films.

Variation of MEMS Thin Film Device Parameters under the Influence of Thermal Stresses.

With the advancement of semiconductor manufacturing technology, thin film structures were widely used in MEMS devices. These films played critical roles in providing support, reinforcement, and insulation in MEMS devices. However, due to their microscopic dimensions, the sensitivity of their parameters and performance to thermal stress increased significantly. In this study, a Pirani gauge sample with a multilayer thin film structure was designed and fabricated. Based on this sample, finite element modeling analysis and thermal stress experiments were conducted. The finite element modeling analysis employed a combination of steady-state and transient methods to simulate the deformation and stress distribution of the device at room temperature (25 °C), low temperature (-55 °C), and high temperature (125 °C). The thermal stress test involved placing the sample in a temperature cycling chamber for temperature cycling tests. After the tests, the resonant frequency and surface deformation of the device were measured to quantitatively evaluate the impact of thermal stress on the deformation and resonant frequency parameters of the device. After the experiments, it was found that the clamped-end beams made of Pt were a stress concentration area. Additionally, the repetitive thermal load caused the cantilever beam to move cyclically in the Z direction. This movement altered the deformation of the film and the resonant frequency. The suspended film exhibited concavity, and the overall trend of the resonant frequency was downward. Over time, this could even lead to the fracture of the clamped-end beams. The variation of mechanical parameters derived from finite element simulations and experiments provided an important reference value for device design improvement and played a crucial role in enhancing the reliability of thin film devices.

Stretchable Composite Films Are Prepared by Using Cellulose Pulp with Differential Substitution of Carboxymethyl Cellulose and Thymol with an Infrared Heating Process for Packaging Application.

Herein, cellulose pulp (CP), carboxymethyl cellulose (CMC), and thymol-based eco-friendly, transparent, and flexible composite films are prepared. These materials dissolved well in an environment-friendly process in N-methyl morpholine N-oxide (NMMO) ionic liquids using infrared heating. Fourier-transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), and scanning electron microscopy (SEM) analyses are used to study the structure, microstructure, and morphology of the composite films. The thermal properties of the CP/CMC/thymol composites are thoroughly studied by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The thermal stability of the composites (T 5%-57.8-91.2 °C and T 10%-216.6-284.1 °C) significantly improves following the CMC addition. In each case, all the composite film exhibits unique T g (140.5-143.1 °C) values, as confirmed by DSC. The tensile strength of the cellulose pulp is 66.5 MPa, increasing to 78.4 MPa for the CP/CMC-1:0.5 composites and steadily increasing to 93.8 MPa with increasing CMC content. Similarly, CMC increases the EB of cellulose pulp from 9.3 to 7.4%. The water vapor permeability and swelling ratio values of the CP/CMC/thymol composites are in the range of 1.9-2.11 × 10-9 g/(m2·Pa·s) and 52.5-50.8° respectively. The CP, CMC, and thymol-based composite do not exhibit cytotoxicity to the aneuploid immortal keratinocyte cell line and demonstrate excellent antioxidant properties, for promising packaging and biomedical applications.

Effect of strain gradient and interface engineering on the high-temperature energy storage capacitors

The miniaturization and high integration of electronic devices pose new requirements for the energy storage density and high-temperature performance of dielectric capacitors. For thin film materials, internal stress and the interface layer often show a significant impact on their energy storage performance. Therefore, the capacitors with different stress gradient sequences and different periods were designed by BaHf0.17Ti0.83O3 (BHTO17), BaHf0.25Ti0.75O3 (BHTO25), and BaHf0.32Ti0.68O3 (BHTO32) to investigate the effect of stress gradient and interface engineering on the energy storage characteristics. Dielectric thin film structures with upward gradient, downward gradient, and periodic upward gradient (4N) were constructed. The study found that the upward gradient structure had higher breakdown field strength than the downward gradient structure. This is because the upward gradient structure can effectively extend the ending electric field of the Ohmic conduction mechanism and delay the activation electric field of the F–N tunneling mechanism. The 4N structure had a slightly higher breakdown field strength (reaching 9.22 MV/cm) compared to the pure upward gradient structure. The 4N structure thin film also exhibited higher energy storage density (115.44 J/cm3) and wide temperature (−100 to 400 °C) characteristics. These findings provide important guidance and application value for improving the energy storage characteristics of dielectric capacitors at high temperatures through structural design.

Effect of structural evolution and orientation behavior on optical properties of iodine-dyed PVA film during uniaxial stretching

In the process of preparing polarizing film, based on the research on the influence of the initial condensed structure of Poly (vinyl alcohol) (PVA) film on the dyeing and stretching process, the connection between the structure and performance of polarizing film is established, which is more conducive to understanding the post-processing process of solution casting molding of optical grade PVA film and the optimization of subsequent dyeing and stretching process. In this paper, PVA film with an appropriate swelling degree were selected for dyeing treatment, and the evolution of the condensed structure during stretching was studied in detail. The work also examined the formation and orientation of PVA-iodine complexes and the feedback effect of complex formation on the structural evolution of the film, with the goal of establishing the relationship between stretching ratio, structure, and performance of the polarizing film. The results show that the dyeing process inhibits the recrystallization of the PVA film during uniaxial stretching. However, the PVA-iodine complexes formed act as "anchors" to stabilize the oriented microfiber network, reducing the critical strains (εw and εs) required for the PVA film to enter the strain-hardening zone. Furthermore, as strain increases, the content of polyiodide ions and PVA-iodine complexes in the dyed PVA film also increases, especially making the formation of long iodide chains (I5−) and PVA-I5− complex more sensitive. Additionally, with increasing strain, both the transmittance and degree of polarization of the dyed PVA film improve, reaching optimal values in the strong strain-hardening zone (>εs). This indicates that εs is the minimum critical strain required to ensure optimal polarization performance of the film in the visible light region.

Pinning of domain walls in epitaxial garnet film patterned by surface arrays of ferromagnetic metal particles

Rare-earth iron garnet epitaxial films famous for their unique magnetic, microwave and optical properties consistently attract high interest. Domain structure of both bulk and interfaces of garnet films is closely connected with their magnetic properties and magnetization dynamics. In this work, we investigate the magnetic behaviour and domain structure of an epitaxial bismuth-substituted lutetium iron garnet film with a regular array of planar submicron particles made of Co film or Co/Pt multilayer on its surface. Optical polarization microscopy and magnetic force microscopy techniques used for the characterization of these composite structures confirm the mutual influence of the garnet and metal nanostructured layers on each other. On the one hand, dense ordered metal particles provide the pinning of the surface magnetic domains of the garnet film, which further affects the organization of the bulk stripe domains. On the other hand, we observed that the domain structure in the metallic pattern is governed by the domain structure of the garnet placed beneath it.

Metal-semiconductor-metal UVA photodetector based on TiO2 thin films synthesized via liquid phase deposition method

In this work, titanium dioxide (TiO2) thin film-based metal-semiconductor–metal (MSM) ultraviolet (UV) photodetectors (PDs) were fabricated on glass substrates via liquid phase deposition (LPD) technique at various deposition time in the range of 3–6 h. Varying deposition time significantly impacted the physical properties of the films. Increasing the deposition time revealed a mixture of clusters and hexagonal-like structures in film’s morphology. The energy band gap of the TiO2 films decreased from 3.30 to 3.09 eV upon increasing the deposition time. Photodetection characteristics were examined by exposing the MSM UV PD to 390 nm UV light with an intensity of 1.6 mW cm−2 and a bias voltage of 5 V. The fabricated PDs implied characteristics of I-V ohmic contact. The optimum photodetection characteristics were achieved for TiO2 film deposited at 6 h which exhibited 36.9 μA maximum photocurrent, 20080.3% sensitivity, 201.80 gain, 225 mA W−1 responsivity, 81.07% external quantum efficiency, 0.276 s response time, and 0.274 s recovery time. The photoelectric properties of the films were strongly affected by the increased grain size and improved crystallinity of the films due to the prolonged deposition time. The optimum film demonstrated its potential to be a promising candidate for UV PD applications.

Preparation and properties of fluorinated VAc-VeoVa10 latex emulsified with allyl nonyl phenoxy propyl alcohol polyoxyethylene ether ammonium sulphate

Purpose The traditional VeoVa10-VAc copolymer latex, which prepared via the emulsion polymerization of the mixed monomers of VAc and VeoVa10, has the poor water resistance and thermal stability because of the migration of the conventional emulsifier molecules and the low bond energy of C-C bond. The purpose of this work is that the fluorinated monomer is used to modify the latex. The film of the resultant latex has the C-F bond with high bond energy and low surface energy, which can effectively improve the heat resistance and water resistance of the resultant film. In addition, the reactive emulsifier is used to replace the conventional emulsifier. The drawbacks of the conventional emulsifier molecules migrate and desorb can be avoided when the polymer latex is stored, thereby also improving the water resistance. Design/methodology/approach The modified VAc-VeoVa10 latex has been successfully synthesized via the semi-continuous seeded emulsion polymerization, which VAc and VeoVa10 is used as the main monomers and HFMA was used as the functional monomer. KPS and reactive surfactants of SE-10 were used as the initiator and emulsifier, respectively. The structure of resultant latex film was characterized by Fourier transform infrared spectroscopy (FTIR). The latex films were tested by thermogravimetric analysis (TGA), differential scanning calorimetry (DSC) and contact angle (CA). The particle size and its distribution of the latex were measured by the nano particle size analyzer. Findings The factors that had an influence on the properties of the latex and the film were investigated in detail. The stability of the resultant latex is good. The average particles of the latex and its distribution are small and uniform, respectively. In comparison with the conventional latex film, the thermal stability and hydrophobicity of the resultant latex film are improved obviously. Practical implications The resultant latex can be used in both the waterborne interior and exterior wall coatings, pickering stabilized waterborne polymer dispersions, polymer powders, environmentally friendly polymer-modified waterproof mortar and other fields, which can be satisfied with the high demand of thermal stability and hydrophobicity. Originality/value The modification of poly (VAc-VeoVa10) by reactive surfactant and fluorinated monomer is seldom reported. In this study, the fluorinated poly (VAC-VeoVa) latex is prepared via the reactive surfactants, which VAc and VeoVa10 is used as the main monomers and hexafluorobutyl methacrylate is used as the functional monomer. Potassium persulfate (KPS) and allyl nonyl phenoxy propyl alcohol polyoxyethylene ether ammonium sulfate are used as the initiator and emulsifier, respectively.

Modeling the influence of technological parameters of the magnetron sputtering process using the Caroline D12C system on the proportion of nanocrystallites in the structure of thin silicon films

Modeling the influence of technological parameters of the magnetron sputtering process using the Caroline D12C system on the proportion of nanocrystallites in the structure of thin silicon films

Impact of Silver Incorporation and Flash-Lamp-Annealing on the Photocatalytic Response of Sputtered ZnO Films.

Thin films of silver-doped zinc oxide (SZO) were deposited at room temperature using a DC reactive magnetron co-sputtering technique using two independent Zn and Ag targets. The crystallographic structure, chemical composition and surface morphology of SZO films with different silver concentrations were correlated with the photocatalytic (PC) properties. The crystallization of the SZO films was made using millisecond range flash-lamp-annealing (FLA) treatments. FLA induces significant structural ordering of the wurtzite structure and an in-depth redistribution of silver, resulting in the formation of silver agglomerates. The wurtzite ZnO structure is observed for silver contents below 10 at.% where Ag is partially incorporated into the oxide matrix, inducing a decrease in the optical band-gap. Regardless of the silver content, all the as-grown SZO films do not exhibit any significant PC activity. The best PC response is achieved for samples with a relatively low Ag content (2-5 at.%) after FLA treatment. The enhanced PC activity of SZO upon FLA can be attributed to structural ordering and the effective band-gap narrowing through the combination of silver doping and the plasmonic effect caused by the formation of Ag clusters.

Insight into wave propagation in polyimide films and resistive grid sandwich structures towards a hybrid monitoring of hypervelocity impact

Micro-Meteoroid and Orbital Debris pose a significant threat to the safe operation of orbiting spacecraft, potentially leading to mission failure in space exploration. Quantitative characterization of hypervelocity impact (HVI) is crucial to ensure the safety and successful completion of on-orbit missions. Firstly, this study designed a three-layer sandwich structure of polyimide film with orthogonally laid resistive wires, combined with piezoelectric and resistive wire sensors, for the simultaneous acquisition of acoustic emission (AE) signals generated by HVI and measurement of perforation dimensions. Secondly, a semi-analytical finite element (SAFE) analysis of wave dispersion properties in the periodic sandwich structure is conducted with Bloch’s theorem, together with a hybrid model based on three-dimensional smoothed particle hydrodynamics and finite element methods (SPH-FEM) to comprehensively understand the AE waves and damage characteristics induced by HVI. The resulting anisotropic wave propagation characteristics with SAFE and SPH-FEM are closely matched. Thirdly, a time delay-multiplication (TDM) imaging algorithm considering wave velocity anisotropy is proposed for accurate real-time “visualization” of HVI locations. Lastly, correlations are established between projectile and perforation dimensions. The proposed algorithm for HVI multi-parameter quantification and damage detection helps evaluate the space HVI environment and HVI-induced damage to spacecraft.

Novel electrochromic-supercapacitor device based on P(TPACz)/WO3-PDA nanocomposite film

Organic–inorganic composites of (E)-3,5-di(9 H-carbazol-9-yl)-N-(4-(diphenylamino)benzylidene)aniline/dopamine-modified WO3 (P(TPACz)/WO3-PDA) were prepared by electrochemical polymerisation. The as-prepared P(TPACz)/WO3-PDA composites showed good electrochromic and electrochemical performance. The prominent electrochemical performance of P(TPACz)/WO3-PDA represents a high areal capacitance (32.15 mF cm−2 at 0.1 mA cm−2) and wide range of potential windows (-2.0−1.6 V). Additionally, symmetric supercapacitor devices based on P(TPACz)/WO3-PDA composite films were successfully constructed, which exhibited a high specific capacitance (13.88 mF cm−2 at 0.02 mA cm−2) and an energy density of 7.71 × 10−3 mWh cm−2 in n-doped station. The remarkable electrochromic and electrochemical performances are due to the synergy between the organic polymer and WO3-PDA. A complete large-area composite film structure with high conductivity promises fast electronic transport. This study provides a method for preparing multifunctional composite electrode materials, offering technical support for intelligent displays and energy storage technologies.

Preparation and characterization of a multifunctional film with excellent UV shielding, antibacterial and antioxidant capabilities containing cinnamaldehyde and titanium dioxide (TiO2)

AbstractSoy protein isolated (SPI) have a wide application in the food packaging, but their water resistance, mechanical properties and antibacterial properties are not ideal for directly use. In our study, we developed a series of SPI composite films loaded with cinnamaldehyde and titanium dioxide (TiO2). X‐ray diffraction (XRD), UV scanning spectra (UV) and spectro colorimeter were applied to indicate the structure of films. The incorporation of TiO2 (0.5%) caused a subsequent effect on the tensile property, UV blocking properties and water vapor properties (WVP). On the other hand, SPI film composed with a constant amount of TiO2 and different concentration of cinnamaldehyde showed an excellent synergistic effect to improve the tensile property, moisture content, UV blocking properties, water vapor properties and morphological characteristics. Furthermore, the composite films exhibited superior antibacterial activity when tested against both S. aureus and E. coli. The microstructure of the composite film become heterogeneous and rough after addition of TiO2 and cinnamaldehyde compare to control film. The findings of the present study may facilitate a re‐evaluation of the potential of using multiple compounds to prepare active edible films.

Comparative Study and Analysis of Social Structure and Cultural Values in Chinese and Korean Movies

A comparative study of social structure and cultural values in Chinese and Korean films reveals the unique perspectives and profound differences between the two countries in reflecting social reality and conveying cultural values in their films. Chinese movies tend to depict harmonious and intimate family relationships when showcasing family structure, emphasizing the importance of the family as an individual's emotional support and spiritual sustenance. Korean movies, on the other hand, focus more on showcasing the complexity and conflicts within families, reflecting social reality and the depth of human nature through the entanglements among family members. This difference reflects the different emphasis on family values and social values between China and South Korea. In terms of social class, Chinese movies often focus on the survival status and struggle process of the lower class society, showcasing social injustice and contradictions by telling stories of ordinary people. This kind of attention reflects the humanistic care of Chinese films towards vulnerable groups and their profound reflection on social issues. Korean movies, on the other hand, tend to reveal and criticize the power and corruption of the upper class, reflecting the dark side of society by depicting social phenomena such as collusion between politics and business, and power and money transactions. This difference reflects the different orientations of social class concepts and social responsibility between China and South Korea.

Features of the structure and resistive switching of titanium oxide films on Y-cut piezoelectric substrate of a LiNbO3 crystal

The difference in the structure of titanium oxide thin films deposited on fused silica substrates and the Y-cut of a lithium niobate crystal is demonstrated. In both cases, the film is amorphous; however, an insignificant amount of rutile crystallites is observed in the film formed on the Y-cut of the lithium niobate crystal. It is shown that the electrical characteristics of the films depend not only on the material of the substrate, but, in the case of the lithium niobate substrate, also on the direction of an electric field. This is caused by the deformation of the substrate due to the inverse piezoelectric effect.

Comprehensive analysis of charge carriers dynamics through the honeycomb structure of graphite thin films and polymer graphite with applications in cold field emission and scanning tunneling microscopy

Polymer graphite electron sources have performed satisfactorily as field emission emitters and scanning tunneling microscopy probes in the past few years. However, the emission process was characterized by limited total emission currents. This paper introduces the elemental, vibrational, electronic structure, and optical analysis of polymer graphite and glass-graphite composite field emission cathodes to study these limitations. Moreover, the field emission characteristics are studied including the changes in the potential energy barrier of the used materials and structures. Among the studied structures, the cathodes prepared from graphite thin films deposited on a micropointed glass substrate (film-GMF) showed superior performance as random field emission arrays. This includes obtaining much higher emission current values ≈ 20 times) and lower threshold voltages ≈ 1/2) compared to the results obtained from polymer graphite samples. The enhancement factor in such emitters is believed to be the three-dimensional honeycomb structure of graphite. Moreover, the study includes applying graphite coatings to tungsten nano-field emission cathodes and scanning tunneling microscopy probes, which improves the performance of such cathodes/probes in both microscopic techniques.

Study of endogenous chloride ion content on the behavior of steel bar depassivation in sea sand concrete

In this study, we investigated the chloride concentration in sea sand that induces corrosion in steel bars, as well as the corrosion mechanisms of steel bar within sea sand concrete. Different analytical techniques indicated that the chloride concentration for steel bar corrosion in sea sand concrete was 0.03 % (when the water-binder ratio was in the range of 0.4–0.6). First, the calcium silicate in sea sand concrete reacted with Fe3+ to reduce the compactness of the oxide layer and increase the corrosion risk of steel bars. Second, as the water-binder ratio and chloride concentration gradually increased, the loose structure of the passive film increased, and the relatively dense structure decreased, which made it easier for chloride ions to penetrate the outer layer of the passive film to erode the steel matrix. Besides, the reaction of chloride ions with C3A to form Friedel's salt optimized the pore structure and reduced the content of free chloride ions. However, the adverse effect of chloride ions on the passive film of steel bars exceeded the beneficial impact of porosity reduction. These findings allow us to better apply sea sand to improve the sustainable development of environment.