Fiber Components Research Articles

Study on the performance of ground melon vine straw fiber modified asphalt

In order to reduce the waste of resources and the pollution of ecological environment caused by the large amount of waste crop straw accumulation or incineration, and to realize the high-value utilization of waste straw resources, this paper adopts the mechanical crushing method, acid and alkali solution treatment method to prepare the groundnut seedling straw fibers, and compares and analyzes the micro-morphology and chemical composition and thermal stability of the groundnut seedling straw fibers prepared by the physical method, the NaOH solution method, and the HCL solution method, through the scanning electron microscope, infrared spectroscope and the thermogravimetric analysis test; secondly, the optimal blending range of the groundnut seedling straw fibers is preferred. Secondly, the optimal dosage range of ground melon vine straw fiber was selected, the preparation process of ground melon vine straw fiber modified asphalt was proposed, five different dosages of ground melon vine straw fiber modified asphalt were prepared, and the basic properties, viscosity and temperature characteristics, and storage stability of ground melon vine straw fiber modified asphalt were analyzed; and then, a dynamic shear rheometer was used. Dynamic Shear Rheometer and Bending Beam Rheometer tests were used to study the high and low temperature rheological properties and resistance to permanent deformation of ground melon vine straw fiber modified asphalt, and the optimal dosage of groundnut seedling straw fibers was determined; finally, through Fourier Transform Infrared Spectroscopy and Scanning Electron Microscopy tests, the chemical components of ground melon vine straw fiber modified asphalt were clarified, and the chemical components of ground melon vine straw fiber modified asphalt were revealed to be the most important. The toughening mechanism of ground melon vine straw fiber modified asphalt was revealed. The results showed that the chemical alkali treatment method was the best preparation process for groundnut straw fiber, and the process flow was to use NaOH solution with a mass fraction of 3 % to treat the ground melon vine straw fiber for 50 min at a temperature of 60 °C; compared with the matrix asphalt, the needle penetration and elongation of the ground melon vine straw fiber modified asphalt decreased with the increase of the blending amount, and the softening point, the equivalent softening point, and the temperature sensitivity of the asphalt increased. Sensitivity enhancement, softening point difference in line with the specification requirements, but the ductility in the low dosage improved; with the increase in the dosage of ground melon vine straw fiber, ground melon vine straw fiber modified asphalt rutting factor, creep modulus, 0.4 %–1 % dosage of the creep rate and creep recovery rate increased, while 1.3 %–1.6 % dosage of the creep rate and the amount of unrecoverable creep flexibility decreased The results show that 0.4 %–1.6 % dosage of melaleuca alternifolia straw fiber modified asphalt high temperature performance and resistance to permanent deformation performance, and 0.4 %–1 % dosage of melaleuca alternifolia straw fiber low temperature performance has also been improved, the overall consideration, to determine the optimal dosage of melaleuca alternifolia straw fiber 1 %; melaleuca alternifolia straw fibers (NaOH) and the asphalt combined with the production of new functional groups, and melaleuca alternifolia straw fibers with each other. Lap cross to form a fiber skeleton grid structure, can play a role in the entire material to transfer stress and crack resistance, asphalt to play the role of enhanced toughening effect.

Physicochemical, Antioxidant, Starch Digestibility, and Sensory Properties of Wheat Bread Fortified with Taiwanese Cocoa Bean Shells.

The effects of replacing 5-25% of wheat flour (WF) with Taiwanese cocoa bean shells (CBSs) on the physicochemical, antioxidant, starch digestion, and sensory properties of the bread were studied. The lead (0.18) and cadmium (0.77) contents (mg/kg) of the CBSs were below the Codex Alimentarius specifications for cocoa powder. Ochratoxin A and aflatoxins (B1, B2, G1, and G2) were not detected in the CBSs. The CBSs were rich in dietary fiber (42.9%) and bioactive components and showed good antioxidant capacity. The ash, fat, protein, dietary fiber, crumb a* and c*, hardness, chewiness, total phenols, and antioxidant activities of the bread increased with an increasing CBSs level. The starch hydrolysis rate (45.1-36.49%) of the CBS breads at 180 min was lower than that of the control (49.6%). The predicted glycemic index of the bread (CBS20 and CBS25) with 20-25% of the WF replaced with CBSs was classified as a medium-GI food using white bread as a reference. In the nine-point hedonic test, the overall preference scores were highest for control (6.8) and CBS breads, where CBSs replaced 5-10% of WF, with scores of 7.2 and 6.7. CBS20 supplemented with an additional 20-30% water improved its volume, specific volume, and staling rate, but the overall liking score (6.5-7.2) was not significantly different from the control (p > 0.05). Overall, partially replacing wheat flour with CBSs in the production of baked bread can result in a new medium-GI value food containing more dietary fiber, bioactive compounds, and enhanced antioxidant capacity.

Successive self-nucleation and Annealing technique applied to polypropylene/butyl rubber composites: Recycling alternatives for vacuum bagging materials

The aerospace sector uses butyl rubber to manufacture carbon fiber components through an autoclave or infusion. Both manufacturing techniques require a high vacuum to achieve adequate impregnation of the carbon fiber fabrics with epoxy resin, and butyl rubber is used as the sealant. The aerospace sector discontinues materials with shelf life expired, and butyl rubber is one of the materials most discontinued for not being used within the designated time. This work presents the development of composites using polypropylene and discontinued butyl tape. Composites with 30, 50, and 70 wt% of butyl rubber content were prepared using a twin-screw extruder. The structural analysis showed that the composites with 50 wt% and 70 wt% are similar to butyl rubber, while the compound with 30 wt% of butyl is similar to polypropylene. The degree of crystallinity of the compound with 50 wt% of butyl content was 18% higher than the PP, and the melting temperature decreased by 30% with the higher butyl content. SSA revealed that the highest enthalpic contribution occurred in the crystalline fraction of higher perfection, except for the compound with 50 wt% of butyl content, whose less perfect crystalline populations grew at the expense of the most perfect crystals. The reduction of the crystalline fraction implies that butyl interferes with the formation of crystals, developing populations with lower lamellar thickness that favors the overall crystallinity of the compound. Young’s modulus, yield strength, and nominal strain decreased with butyl rubber content. The composites showed rough failure surfaces with solid butyl rubber particles and poor adhesion to polypropylene. Butyl particles with diverse sizes and geometries lead to sudden failure of the composites and high dispersion in strain values.

Milletomics: a metabolomics centered integrated omics approach toward genetic progression.

Producing alternative staple foods like millet will be essential to feeding ten billion people by 2050. The increased demand for millet is driving researchers to improve its genetic variation. Millets include protein, dietary fiber, phenolic substances, and flavonoid components. Its climate resilience makes millet an appealing crop for agronomic sustainability. Integrative omics technologies could potentially identify and develop millets with desirable phenotypes that may have high agronomic value. Millets' salinity and drought tolerance have been enhanced using transcriptomics. In foxtail, finger, and pearl millet, proteomics has discovered salt-tolerant protein, phytohormone-focused protein, and drought tolerance. Metabolomics studies have revealed that certain metabolic pathways including those involving lignin, flavonoids, phenylpropanoid, and lysophospholipids are critical for many processes, including seed germination, photosynthesis, energy metabolism, and the synthesis of bioactive chemicals necessary for drought tolerance. Metabolomics integration with other omics revealed metabolome engineering and trait-specific metabolite creation. Integrated metabolomics and ionomics are still in the development stage, but they could potentially assist in comprehending the pathway of ionomers to control nutrient levels and biofortify millet. Epigenomic analysis has shown alterations in DNA methylation patterns and chromatin structure in foxtail and pearl millets in response to abiotic stress. Whole-genome sequencing utilizing next-generation sequencing is the most proficient method for finding stress-induced phytoconstituent genes. New genome sequencing enables novel biotechnological interventions including genome-wide association, mutation-based research, and other omics approaches. Millets can breed more effectively by employing next-generation sequencing and genotyping by sequencing, which may mitigate climate change. Millet marker-assisted breeding has advanced with high-throughput markers and combined genotyping technologies.

Systematic multistep extraction process for the total valorization of fiber fractions from fruit seeds

This study explores a systematic multistep extraction process to valorize various fruit seeds (mango, cherry, lemon, pumpkin, avocado, litchi, peach, and apricot) by fractionating and isolating different fiber components. A first mild treatment, i.e., a protease-assisted extraction, was employed to disaggregate the plant cell structure and isolate soluble fibers. Subsequently, the insoluble residue underwent extraction by hot acidic water to solubilize and separate the pectin fraction. The remaining solid material was finally subjected to hydrothermal treatment to recover recalcitrant hemicellulose. Cherry, lemon, and pumpkin seeds emerged as the most advantageous by-products overall, showing great extractable quantities of low molecular weight pectin, pectin oligosaccharides, arabinogalactans, xylan, and xylo-oligosaccharides (extraction yields up to 63% and 68% in the first and third step, respectively). Peach and apricot seeds yielded fiber extracts that were similar to each other but distinct for each fraction, suggesting potential applications in different food formulations, albeit with lower yields. The purity of the extracts increased with each stage, reaching 42.6% for soluble fibers, 67.3% for pectin, and 76.1% for hemicellulose. Mango, avocado, and litchi seeds were less suitable for this method but could be utilized for starch recovery. This cascade process effectively maximizes the utilization of fruit by-products, offering a scalable solution for the sustainable extraction of valuable fibers.

Long-term stability of squeezed light in a fiber-based system using automated alignment.

Providing a cloud service for optical quantum computing requires stabilizing the optical system for extended periods. It is advantageous to construct a fiber-based system, which does not require spatial alignment. However, fiber-based systems are instead subject to fiber-specific instabilities. For instance, there are phase drifts due to ambient temperature changes and external disturbances and polarization fluctuations due to the finite polarization extinction ratio of fiber components. Here, we report the success of measuring squeezed light with a fiber system for 24h. To do this, we introduce stabilization mechanics to suppress fluctuations in the fiber system and an integrated controller to automatically align the entire system. The squeezed light at a wavelength of 1545.3nm is measured every 2min, where automated alignments are inserted every 30min. The squeezing levels with an average of -4.42 dB are recorded with an extremely small standard deviation of 0.08 dB over 24h. With the technologies developed here, we can build complicated optical setups with the fiber-based system and operate them automatically for extended periods, which is promising for cloud service of quantum computation.

Using Light Polarization to Identify Fiber Orientation in Carbon Fiber Components: Metrological Analysis.

In this work, a method for measuring tow angles in carbon fiber components, based on the use of a polarized camera, is analyzed from a metrological point of view. Carbon fibers alter the direction of the reflected light's electrical field, so that in each point of the surface of a composite piece, the angle of polarization of reflected light matches the fiber orientation. A statistical analysis of the angle of linear polarization (AoLP) in each pixel of each examined area allows to evaluate the average winding angle. An evaluation of the measurement uncertainty of the method on a cylinder obtained by a filament winding process is carried out, and the result appears adequate for the study of the distribution of angles along the surface of the piece, in order to optimize the process.

Effects of novel halogen-free flame-retardant binary additives on thermal stability, degradation kinetics and flame retardancy of cotton cellulose biomacromolecule

The principal component of cotton fibers is the cellulose biological macromolecule. However, its highly flammable nature has significantly constrained its utilization in fields where flame retardancy is essential. Herein, in this work, a highly effective binary composite flame retardant coating (APP/MEL-SWCNHs) with ammonium polyphosphate and modified single-walled carbon nanohorns (MEL-SWCNHs) was chemically attached to cotton fabric. With the add-on of 11.3 %, the treated cotton fabric (APP/MEL-SWCNHs)4 exhibited remarkable flame-retardant and self-extinguishing properties. Its LOI value increased to 23.7 ± 0.1 %, and the damage length was significantly reduced from 30.0 ± 0.1 % cm to 7.9 ± 0.1 % cm compared to the pristine cotton fabric. Despite partial carbonization, (APP/MEL-SWCNHs)4 preserved its original structure. Importantly, in the cone calorimeter test, both the pHRR and THR of (APP/MEL-SWCNHs)4 were drastically decreased by 71.8 % and 35.8 %, respectively. The APP/MEL-SWCNHs coating functioned as a flame retardant by inhibiting the emission of flammable volatiles, releasing non-flammable gases, and encouraging the formation of char layer during combustion. Significantly, thermal degradation kinetic analysis revealed that the third-order kinetic equation (O3) was found to have the strongest correlation with (APP/MEL-SWCNHs)4 in both air and N2 atmospheres. The higher activation energy (E) for (APP/MEL-SWCNHs)4 confirmed that incorporating MEL-SWCNHs improved the thermal stability of the char layer.

Role of Wilting Time on the Chemical Composition, Biological Profile, and Fermentative Quality of Cereal and Legume Intercropping Silage

Agricultural production in the Azores primarily focuses on the livestock sector, notably, dairy production, where cows graze year-round in a rotational system. To maintain pasture productivity, farmers often rely on synthetic nitrogen fertilizers, which have adverse environmental impacts like ammonia emissions and nitrate leaching. Alternatively, nitrogen-fixing crops like legumes are explored as green manures to enhance soil quality and reduce dependence on chemical fertilizers. The traditional practice of using mixed forages of legumes and grasses, known as “outonos” or intercrops, has been crucial but is declining over time. These mixtures include plants such as lupins, Vicia faba, oats, and vetch, noted for their adaptability and nitrogen-fixing ability. Due to the high perishability of these crops, effective conservation strategies like ensiling are essential to preserve forage nutritional quality through controlled fermentation. This study evaluates the productivity and quality of intercrop forages in the Azores, focusing on fresh samples and silage prepared with wilting times of 0, 24, 48, and 96 h, followed by comprehensive chemical analyses. Results showed significant changes in fiber components (neutral detergent fiber, acid detergent fiber, and acid detergent lignin) with increased wilting time, leading to reduced digestibility. However, wilting improved dry matter content.

Determination of the Best Performing Sri Lankan Maize Landraces Based on the Kernel Nutritional Composition

Maize (Zea mays L.) is one of the most widely cultivated cereal crops in the world as well as in Sri Lanka. Data on the nutritional composition of maize is beneficial for the food and feed industry, but there is a lack of information regarding this avenue in Sri Lanka. Therefore, this study aimed to investigate the suitable landraces with higher nutritional composition among the different landraces by evaluating nutritional parameters using the rank summation index. The maize kernels derived from 42 local landraces were used and the responses were with varieties Bhadra (Control) and Pacific. The proximate composition was analyzed using Near-infrared spectroscopy (NIR) and carbohydrate content and energy were determined using the calculation method. Subsequently, the data were analyzed by performing ANOVA and the rank summation index (RSI) to identify the best performer among the landraces. The results revealed that there were significant differences (p<0.05) among the nutritional components for moisture, ash, fiber, fat, protein, carbohydrates, and energy among the tested landraces. Accordingly, the maize landraces SEU 22, SEU 31, and SEU 2 were identified as the superior germplasms regarding nutritional composition compared with Bhadra, as they exhibited the lowest RSI of 85, 88, and 89, respectively. Therefore, these maize landraces were recommended for future breeding programs for the development of nutritionally enriched maize grains and for sustainable production where land limitation is a challenge.

A Case of FIBROADENOMA Cured with Individualized Homoeopathic Medicine- Evidence Based Homoeopathy

Introduction: Fibro-adenomas are the most common benign tumor of female breast having distinct clinical and Histopathological findings. This case report of fibroadenoma highlights clinical presentation along with proper investigation reports like ultrasound, individualized homoeopathic treatment provided and ongoing follow-up. Palpable mass, nodular swelling, pain, redness and changes in the breast appearance along with fibrous and glandular tissue components are emphasized for proper diagnosis. Homoeopathic literature shows that case of fibro-adenoma had been successfully treated with individualized homoeopathic medicine. Individualized homoeopathic approach to breast fibro-adenoma ensures improved outcomes in mental, emotional as well as physical wellbeing. Case summary: The case report presented here wasa 23 year old female patient, from Repertory OPD, Homoeopathy Hospital, North Eastern Institute of Ayurveda and Homoeopathy, Shillong. The patient was treated with individualized homoeopathic medicine (Phosphorous30, 200) for one year, with significant improvement and progressively decreases in size of tumor.

Enhancing microstructural integrity and mechanical performance of thick wire-arc directed energy deposited eutectic aluminum-silicon solid structure through continuous multi-pass friction stir processing

In wire-arc directed energy deposition (waDED), fabricating larger 3D components with single-layer tracks is challenging due to limitations in track thickness, requiring the development of bead overlapping strategies. However, fusion-based 3D-printed aluminum structures often show porosity and coarse-grained microstructures, limiting their industrial applications. To address these limitations, this study employs continuous multi-pass friction stir processing (FSP) on a waDED-produced aluminum block (140 mm × 150 mm × 28 mm). The severe plastic deformation induced by FSP triggers dynamic recrystallization (DRX), promoting the formation of equiaxed grains with an average grain size 8.75 times smaller than the as-fabricated waDED sample (67.03 μm vs 7.66 μm). Transmission Electron Microscopy (TEM) revealed decreased dislocation loops post-FSP, indicating DRX and dislocation annihilation. X-ray micro-computed tomography (X-CT) examination showed complete elimination of porosity in the waDED sample, owing to the intense mechanical stirring induced during FSP. Scanning electron microscopy (SEM) images of the waDED samples showed fibrous eutectic networks disrupted by FSP, leading to a uniform distribution of broken Si particles within the α-Al matrix. Hardness decreased by approximately 38 % (86 HV0.1 vs 53 HV0.1), while the average ultimate tensile strength decreased by about 4 % in the FSP-treated samples (159.19 MPa vs 153.02 MPa). Additionally, the formation of alpha fiber and weak cube texture components during FSP enhances ductility, as evidenced by a sixfold improvement in elongation (1.93 % vs 11.59 %). This textural transformation contributes to the characteristic deeper and more uniform dimples in the FSP-treated samples, indicative of ductile fracture, compared to the premature failure patterns in as-deposited samples.

Evaluation of the effect of osteosynthesis wires on the structural reorganization of metaepiphyseal cartilage (an experimental and morphological study)

Introduction Premature arrest of bone growth is the most common complication of bone fractures at the growth plate level.The purpose of the work was to evaluate the structural reorganization of metaepiphyseal cartilage following its direct injury with metal and biodegradable wires in an experiment.Materials and methods The metaepiphyseal cartilage of the distal femur of 18 lambs of both sexes was studied. The age of the animals at the beginning of the study was (43.92 ± 0.8) days, by 60 and 120 days (102.63 ± 0.82) and (161.1 ± 0.9) days, respectively. The animals underwent transphyseal insertion of wires/ pins: series 1 — Kirschner wires, series 2 — titanium wires, series 3 — poly-L-lactic acid pins. The duration of the experiment was 60 and 120 days. Clinical and radiographic studies were carried out. Histomorphometry was performed using an AxioScope.A1 microscope and Zenblue software (CarlZeissMicroImagingGmbH, Germany).Results Reactive changes in the growth plate at the interface with the wire were manifested by proliferation of chondrocytes in the zone of proliferating cartilage and in the reserve zone; the minimally expressed changes were noted in series 2, the most pronounced were in series 1. By the end of the experiment, at the interface with the wire in series 1, blood vessels penetrated into the metaepiphyseal cartilage; in series 3 the amount of the fibrous component was increased, which indicates further formation of “bone bridges” and “fibrous bridges,” respectively. In undamaged areas of the growth plate in all series, the zonal structure was preserved. By the end of the experiment, increased values of the thickness of the metaepiphyseal cartilage were noted (1.2 times higher than the control), differences between series were a tendency; in series 2 and 3 the ratio of metaepiphyseal cartilage zones was comparable to the control; in series 1 the proportion of the proliferating cartilage zone was increased by 4 %.Discussion The main problem with growth plate injuries is the formation of bone tissue or fibrosis, which affects the growing process. Currently, the question of choosing a treatment tactic for growth plate injury depending on the size of the “bone bridges” is debatable. Relevant are future comparative studies of the regeneration of metaepiphyseal cartilage defects after the use of fixators made from different materials.Conclusion Histomorphometric characteristics of the growth zone reliably showed that the insertion of wires, regardless of their material, was not accompanied by inhibition of the bone-forming function of the distal metaepiphyseal cartilage of the femur.

Low cross-talk optical addressing of trapped-ion qubits using a novel integrated photonic chip

Individual optical addressing in chains of trapped atomic ions requires the generation of many small, closely spaced beams with low cross-talk. Furthermore, implementing parallel operations necessitates phase, frequency, and amplitude control of each individual beam. Here, we present a scalable method for achieving all of these capabilities using a high-performance integrated photonic chip coupled to a network of optical fibre components. The chip design results in very low cross-talk between neighbouring channels even at the micrometre-scale spacing by implementing a very high refractive index contrast between the channel core and cladding. Furthermore, the photonic chip manufacturing procedure is highly flexible, allowing for the creation of devices with an arbitrary number of channels as well as non-uniform channel spacing at the chip output. We present the system used to integrate the chip within our ion trap apparatus and characterise the performance of the full individual addressing setup using a single trapped ion as a light-field sensor. Our measurements showed intensity cross-talk below ~10–3 across the chip, with minimum observed cross-talk as low as ~10–5.

Oral fibrolipoma in dogs: Retrospective case series study and comparative review.

Fibrolipoma is defined as a typical lipoma transected by variable amounts of paucicellular and collagenous fibrous components. Oral and lingual fibrolipomas are well-recognized histological entities in human medicine that are slightly more prevalent in females, occur most commonly after the fourth decade, and arise from the buccal mucosa. The documentation of this neoplasm in the oral cavity is lacking in veterinary medicine. Through a multi-institutional retrospective compilation of cases submitted to diagnostic pathology services, here we describe the clinical and pathologic features of oral fibrolipomas in dogs. A total of 112 cases of oral fibrolipomas in dogs were retrieved. The mean age was 10.1 years (range 2-16 years, ±2.63 years standard deviation), with an average tumor size of 1.7 cm (range 0.2-8 cm, ±1.1 cm standard deviation). The most common location was the tongue (57.1%, 64/112), followed by the buccal mucosa (15.2%, 16/112), sublingual area (8.0%, 9/112), gingiva and lip (4.5%, 5/112 each), and palate (1 case). The anatomical location of oral fibrolipomas only differed significantly among the dog breeds (P < .001) but not among sex, age, anamnesis, or reason for submission. The tumor was most commonly reported in males (69.7%, 78/112), and in 62.5% (70/112) of the cases, the tumor was an incidental finding. Fibrolipoma should be considered a differential diagnosis when considering benign lingual and other oral soft tissue masses in dogs.

PHYSICAL CHARACTERISTICS OF TYPICAL CHORDAE TENDINEAE OF ATRIOVENTRICULAR VALVULAR HEART APPARATUSES IN CHILDREN OF THE NEONATAL PERIOD IN NORM

This article presents the microscopic structure and polarization characteristics of the chordae tendineae of the mitral and tricuspid heart valves of normal newborns based on histological sections.The purpose – to study histological specimens of chordae tendineae of atrioventricular heart valves of newborn children using light microscopy, as well as using the method of laser polarimetry.Material and methods. The studies were performed on 34 atrioventricular valves taken from the hearts of newborn children (from birth to the 28th day of life). The light-optical and polarization methods were used in the research.Results. The structural components of the chordae tendineae of the mitral and tricuspid heart valves of newborns in norm were studied using the morphological method and the histoarchitectonics of their components at the polarization level was established.Conclusions. Thus, the obtained data of these studies using the method of laser polarimetry completely confirmed the data of the structure of the typical chordae tendinea of the cardiac atrioventricular valvular apparatuses of newborns using light microscopy. This method makes it possible to differentiate fibrous components of the extracellular matrix of connective tissue and contractile cardiac muscle cells within the chordae tendinea, as well as to differentiate chordae tendinea into two types: fibro-muscular and fibrous.

Successful thoracoscopic enucleation of a calcifying fibrous tumor of the lower mediastinum in a young woman

BackgroundCalcifying fibrous tumor (CFT) arising from the pleura is a relatively rare benign lesion in young and middle-aged adults. We report a 31-year-old woman with pleural CFT who underwent successful complete thoracoscopic enucleation.Case presentationAn asymptomatic woman presented with a mass in the right lower lung field that was incidentally detected on a chest X-ray during a routine medical checkup. Chest computed tomography showed a well-defined mass in the lower mediastinum, with a maximum diameter of approximately 5.5 cm. Esophagogastroduodenoscopy showed no abnormal findings in the esophagus. An endoscopic ultrasonography (EUS) revealed a well-defined tumor with no internal blood flow. EUS-fine needle aspiration failed to establish a definitive diagnosis. Therefore, thoracoscopic tumor enucleation was performed for diagnostic and therapeutic purposes. Based on the histopathological findings of the resected specimen, the presence of a tumor with a high fibrous component in a young woman, and the identification of granulomatous calcifications, a diagnosis of CFT was established.ConclusionsComplete thoracoscopic tumor enucleation was successfully performed for CFT arising from the pleura in a young adult woman.

Characterising the effect of commercial wheat grain milling methods on wheat bran characteristics

SummaryTo assess the effect of wheat milling or bran separation method, five wheat bran fractions, one from stone milling (SB), two from roller flour milling (coarse: RB1, fine: RB2), and two from grain pearling (0–3%: PB1, 3–6%: PB2) were analysed. Physiological properties provided good physical and flow characteristics of SB fraction; however, it was the darkest. Particle size was in the order of RB1 &gt; SB &gt; RB2 &gt; PB1 &gt; PB2. The fibre analysis showed the highest insoluble fibre components for RB1, PB1, and exceptionally higher soluble fibre for PB1. The protein, fat, ash, and starch content were highest for RB2 and PB2. Antioxidant properties followed the order PB2 &gt; RB2 &gt; PB1 &gt; RB1 &gt; SB. Pearled fractions (PB1 and PB2) showed better functional properties than others. SEM, XRD, and FT‐IR verified the changes in the properties of bran fractions. The characterisation data will find applications to help increase the usage of bran fractions in specific food products.

Micro-to-Nanoscale Characterization of Femtosecond Laser Photo-Inscribed Microvoids.

Fiber Bragg gratings are key components for optical fiber sensing applications in harsh environments. This paper investigates the structural and chemical characteristics of femtosecond laser photo-inscribed microvoids. These voids are at the base of type III fs-gratings consisting of a periodic array of microvoids inscribed at the core of an optical fiber. Using high-resolution techniques such as quantitative phase microscopy, electron transmission microscopy, and scattering-type scanning near-field IR optical microscopy, we examined the structure of the microvoids and the densified shells around them. We also investigated the high-temperature behavior of the voids, revealing their evolution in size and shape under step isochronal annealing conditions up to 1250 °C.

Seromucinous tumors of ovary: A case series

Seromucinous neoplasms are new category of ovarian epithelial tumor in the 2014 revised World Health Organization classification. Surface epithelial neoplasms are the most common ovarian tumors. Based on the degree of stratification and the presence or absence of invasion, these epithelial proliferations are further divided into benign, borderline, and malignant categories. Benign tumors are divided into three subtypes: cystadenoma (cystic areas), cystadenofibroma (cystic and fibrous areas), and adenofibroma (predominantly fibrous sections). Serous adenofibromas are rare variant of serous surface epithelial tumors. They affect females between the ages of 15 and 65 and make up 1.7% of all benign ovarian tumors. Serous tumor with a solid, fibrous component is designated as serous cystadenofibroma in which both serous and mucinous components are closely intermixed. Seromucinous adenofibroma is a benign cystic neoplasm composed of glands and cysts lined by an admixture of bland mullerian type epithelium which includes ciliated, endocervical type mucinous, and endometroid. They have a characteristic prominent fibromatous hypocellular stroma which helps differentiate it from the commoner cystadenoma. Seromucinous borderline tumors is 10% -20% of all epithelial ovarian tumors. Develops in younger age, usually bilateral in upto 40%, associated with endometriosis. We discuss about four different cases of seromucinous tumor reported in our institute.