Fabry-Perot Cavity Research Articles

High-efficiency and broadband tunable Raman fiber laser in a chalcogenide fiber based on the Fresnel reflection.

A high-efficiency and broadband tunable chalcogenide fiber Raman laser with the Fabry-Perot (F-P) cavity formed by the Fresnel reflection was established. A maximum average power slope efficiency of around 43% and a maximum output peak power of about 2.9 W at 2148 nm were demonstrated by using a 2 µm nanosecond pump source. The laser shows a broadened pulse width of 674 ns and a broadband tunability of the central wavelength from 2100 to 2186 nm. The Raman Fabry-Perot cavity constituted by the Fresnel reflection from chalcogenide fiber endfaces can operate at any wavelength without the aid of any additional optical feedback element. This will facilitate the realization of fiber lasers with excellent performance and compact system, especially in the mid-infrared region.

Tensile Control of Vibrational Strong Light‐Matter Coupling with Flexible Polyester Films

AbstractPolaritons are generated by strong interaction between photons and matter, with the hybridization fundamentally changing the energy landscape of the system. Future exploitation of polaritons will benefit from implementing low‐cost, flexible, and easily tuneable configurations, as electronics have before. Here, coherent coupling of the carbonyl stretch vibrations of polyester (poly(ethylene terephthalate), PET) films to the optical modes of a Fabry–Perot (FP) cavity is presented, in which the FP cavity is directly formed on flexible, free‐standing, and commercially available PET films. For 2‐µm thick PET films, the carbonyl stretch vibration of the PET overlaps with the half‐wavelength FP cavity mode, leading to the coupling of the two modes, a Rabi splitting above 160 cm−1, and associated anticrossing in angular dispersion measurements. The study demonstrates dynamic control of light‐matter interaction strength by modulating film thickness under tension, finding that a 25% tensile stretch can tune the light‐matter interaction from 20:80 mixing to near‐perfect 50:50 hybridization at normal incidence. These findings are discussed in the context of future foldable/twistable/wearable polaritonic devices.

Structure and Self-Modulation Features of the Superradiant States in Asymmetric Fabry–Perot Cavity

Structure and Self-Modulation Features of the Superradiant States in Asymmetric Fabry–Perot Cavity

Validated enhancement and temperature modulated absorbance of a WS2 monolayer based on a planar structure.

Transition-metal dichalcogenides (TMDCs), as emerging optoelectronic materials, necessitate the establishment of an experimentally viable system to study their interaction with light. In this study, we propose and analyze a WS2/PMMA/Ag planar Fabry-Perot (F-P) cavity, enabling the direct experimental measurement of WS2 absorbance. By optimizing the structure, the absorbance of A exciton of WS2 up to 0.546 can be experimentally achieved, which matches well with the theoretical calculations. Through temperature and thermal expansion strain induced by temperature, the absorbance of the A exciton can be tuned in situ. Furthermore, temperature-dependent photocurrent measurements confirmed the consistent absorbance of the A exciton under varying temperatures. This WS2/PMMA/Ag planar structure provides a straightforward and practical platform for investigating light interaction in TMDCs, laying a solid foundation for future developments of TMDC-based optoelectronic devices.

Temperature effects in narrow-linewidth optical cavity control with a surrogate quasi-second-harmonic field

Fabry–Perot cavities are widely used in precision interferometric applications. Various techniques have been developed to achieve the resonance condition via the direct interrogation of the cavity with the main laser field of interest. Some use cases, however, require a surrogate field for cavity control. In this study, we construct a bichromatic cavity to study the surrogate control approach, where the main and the surrogate fields are related by the second-harmonic generation with nonlinear optics. We experimentally verify the temperature dependence of the differential reflection phase of a dielectric coating design optimized for the surrogate control approach of the optical cavities of the light-shining-through-a-wall experiment Any Light Particle Search II and develop a comprehensive cavity model for quasi-second-harmonic resonances that considers also other important factors, such as the Gouy phase shift, for a detailed analysis of the surrogate control approach.

An ultra-thin optical polarizer based on weyl semimetals

Recently, Weyl semimetals have been extensively studied due to their unique optical responses, especially in the mid-infrared region. However, the possibility of developing optical polarizers based on Weyl semimetals remains unexplored. In this paper, under the Voigt geometry, we numerically show that an ultra-thin Weyl semimetal film with thickness L = 100 nm can achieve an impressive polarization extinction ratio (more than 40 dB) with a wide acceptance angle. Further, the proposed sandwich structure can effectively adjust the position of the TE mode transmission peak alone, thus obtaining lower insertion loss (from 0.06 dB to 0.03 dB) and wider acceptance range of angle (from 49.5∘ to 71∘). The proposed gradient Fermi level structure eliminates the Fabry-Perot cavity resonance, thus resulting a wider bandwidth (approximately 60 % improvement). Our proposed ultra-thin and wide-angle polarizer may have potential applications in optical communication and omnidirectional polarization detectors.

A Five-Hole Pressure Probe Based on Integrated MEMS Fiber-Optic Fabry-Perot Sensors.

The five-hole pressure probe based on Micro-Electro-Mechanical Systems (MEMS) technology is designed to meet the needs of engine inlet pressure measurement. The probe, including a pressure-sensitive detection unit and a five-hole probe encapsulation structure, combines the advantages of a five-hole probe with fiber optic sensing. The pressure-sensitive detection unit utilizes silicon-glass anodic bonding to achieve the integrated and batch-producible manufacturing of five pressure-sensitive Fabry-Perot (FP) cavities. The probe structure and parameters of the sensitive unit were optimized based on fluid and mechanical simulations. The non-scanning correlation demodulation technology was applied to extract specific cavity lengths from multiple interference surfaces. The sealing platform was established to analyze the sealing performance of the five-hole probe and the pressure-sensitive detection unit. The testing platform was established to test the pressure response characteristics of the probe. Experimental results indicate that the probe has good sealing performance between different air passages, making it suitable for detecting pressure from multiple directions. The pressure responses are linear within the range of 0-250 kPa, with the average pressure sensitivity of the five sensors ranging from 11.061 to 11.546 nm/kPa. The maximum non-linear error is ≤1.083%.

Consequences of Vibrational Strong Coupling on Supramolecular Polymerization of Porphyrins.

Supramolecular polymers display interesting optoelectronic properties and, thus, deploy multiple applications based on their molecular arrangement. However, controlling supramolecular interactions to achieve a desirable molecular organization is not straightforward. Over the past decade, light-matter strong coupling has emerged as a new tool for modifying chemical and material properties. This novel approach has also been shown to alter the morphology of supramolecular organization by coupling the vibrational bands of solute and solvent to the optical modes of a Fabry-Perot cavity (vibrational strong coupling, VSC). Here, we study the effect of VSC on the supramolecular polymerization of chiral zinc-porphyrins (S-Zn) via a cooperative effect. Electronic circular dichroism (ECD) measurements indicate that the elongation temperature (Te) of the supramolecular polymerization is lowered by ∼10 °C under VSC. We have also generalized this effect by exploring other supramolecular systems under strong coupling conditions. The results indicate that the solute-solvent interactions are modified under VSC, which destabilizes the nuclei of the supramolecular polymer at higher temperatures. These findings demonstrate that the VSC can indeed be used as a tool to control the energy landscape of supramolecular polymerization. Furthermore, we use this unique approach to switch between the states formed under ON- and OFF-resonance conditions, achieved by simply tuning the optical cavity in and out of resonance.

Hybrid Photonic Structures: Gallium Phosphide Nanowires Decorated with Carbon Dots for Enhanced Broadband Emission

AbstractCarbon dots (CDs) are promising nanostructures in the field of photonics owing to the ease of fabrication, tunable and efficient emission. Gallium phosphide (GaP) nanowires are known for high surface area, optical density, waveguiding, resonant optical properties but lacking the luminescence due to the indirect bandgap. Here, hybrid photonic structures – GaP nanowires decorated with the CDs are fabricated and studied. Feasible drop‐casting deposition technique allows fabrication of dense vertical structures exhibiting efficient photoluminescence. Deposition of the CDs over the nanowires does not affect their luminescent properties demonstrating tolerance of the approach toward the surface aggregation. Tuning of the emission spectrum is obtained via variation of the excitation wavelength and CDs’ synthesis protocol. The structures emitting throughout the visible range are obtained. Analysis of the photoluminescence of an individual structure demonstrates the most intense and fast recombination processes at the ends of a nanowire. It is shown that the luminescence of the CDs’ covering a nanowire acting as a Fabry–Perot cavity is enhanced up to a factor of 3 governed by the Purcell effect. The obtained results unveil a path for fabrication of novel photonic devices via decoration of optically dense nanowires with CDs for enhanced and directed broadband emission.

Investigation of a Pyramid-like Optical Absorber with High Absorptivity in the Range of Ultraviolet A to Middle Infrared

In this study, a simple pyramid-like ultra-wideband absorber was designed to explore high absorptivity across a wide bandwidth. The absorber consisted of eight layers organized into four groups, and each group comprised a metal layer followed by an oxide layer, both of which were square with equal side lengths. Specifically, the chosen oxides, arranged from bottom to top, included SiO2 (t7 layer), Al2O3 (t5 layer), SiO2 (t3 layer), and Al2O3 (t1 layer). In the initial design phase, the thickness of the t8 Ti layer was set to 50 nm and assigned initial values to the thicknesses of the t7-t1 layers, and the widths of the four groups w4, w3, w2, and w1, decreased successively from bottom to top, creating a structure reminiscent of a pyramid. Comsol (version 6.0) was utilized to simulate and systematically vary one parameter at a time, ranging from the thicknesses of the t7-t1 layers to the widths of w4-w1, in order to identify the most suitable structural parameters. Our analyses demonstrated that multimode resonance arose due to the emergence of absorption peaks at lower wavelengths between larger and smaller areas. Additionally, surface plasmon resonance and interference effects between various layers and materials were attributed to the alternating arrangement of metal and oxide layers. The enhancements in the electric field observed at different resonance peak wavelengths illustrated the Fabry–Perot cavity effect, while the impedance matching effect was observed through variations in the real and imaginary parts of the optical impedance with respect to the wave vector. After simulating using these optimally found thicknesses and widths, the aforementioned effects manifested in the pyramid-like ultra-wideband absorber we designed, with its absorptivity surpassing 0.900 across the spectrum from ultraviolet A (335 nm) to middle infrared (4865 nm).

Ultrathin tunable UWB metasurface absorber design by exciting plasmonic modes in bilayer graphene stack

This work presents a graphene-based ultra-wideband (UWB) tunable metasurface absorber (MSA) consisting of top patterned graphene (Gpat) and bottom continuous graphene (Gcont) separated by a 2 μm thick silicon dioxide (SiO2) substrate. An absorptivity (Af) ≥ 90 % from 0.1 to 14 THz (fractional bandwidth = 197.2 %) has been achieved in three steps: (i) Fabry-Perot cavity mode has been generated near 0.1 THz using bilayer graphene stack, (ii) multiple plasmonic modes have been excited by engraving resonant slots on Gpat and (iii) plasmonic coupling strength has been enhanced between Gpat and Gcont by adjusting SiO2 substrate's thickness. The excited plasmonic modes show high absorption due to the generation of localized surface plasmon polariton (LSPP) waves. The fourfold symmetry in design nullifies the effect of the polarization angle (ϕ). Interestingly, the orthogonal modes' excitation helps to achieve similar Af response under both transverse electric and transverse magnetic polarizations for incidence angle (θ) up to 60°. Further, an effective DC biasing mechanism has been devised to tune the chemical potential (μc) of the interconnected Gcont, which ensures common DC bias between unit cells. A DC voltage from 0 to 10.2 V can vary μc (Bottom) from 0 to 1 eV to provide frequency tunability.

All-sapphire fiber-optic sensor for the simultaneous measurement of ultra-high temperature and high pressure

An all-sapphire fiber-optic extrinsic Fabry-Perot interferometric (EFPI) sensor for the simultaneous measurement of ultra-high temperature and high pressure is proposed and experimentally demonstrated. The sensor is fabricated based on all-sapphire, including a sapphire fiber, a sapphire capillary and a sapphire wafer. A femtosecond (fs) laser is employed to drill a through hole at the side wall of the sapphire capillary to allow gas flow. The sapphire fiber is inserted from one side of the sapphire capillary. The sapphire wafer is fixed at the other side of the sapphire capillary. The first Fabry-Perot (FP) cavity, composed of the end face of the sapphire fiber and the front surface of the sapphire wafer, is used for measuring pressure, while the second FP cavity, composed of the two surfaces of the sapphire wafer, is used for measuring temperature. Experimental results show that the sensor can simultaneously measure ultra-high temperature and gas pressure within the temperature range of 20 - 1400 °C and the pressure range of 0 - 5 MPa. The temperature sensitivity is 0.0033 µm/°C, and the pressure sensitivity decreases as the temperature increases, reaching 1.8016 µm/MPa and 0.3253 µm/MPa at temperatures of 20 °C and 1400 °C, respectively.

Optical characterization of a fiber Fabry-Perot cavity: precision measurement of intra-cavity loss, transmittance, and reflectance

We propose and demonstrate a method for characterizing the individual mirror parameters of a fiber Fabry–Perot cavity (FFPC). By measuring the reflection and transmission spectra of the FFPC with an incident laser propagating from the two mirrors of the FFPC and considering several normal or unique losses, the transmittance, reflectance, and intra-cavity loss of the individual mirrors can be determined. Due to the intrinsic limitation of cavity length, traditional powerful methods, such as the cavity ring-down technique, are not applicable to FFPCs for characterizing the parameters of individual mirrors. This scheme provides a dependable method for assessing FFPC mirrors and provides a significant capability for the implementation of strong-coupling cavity quantum electrodynamics based on FFPCs.

Kerr-Enhanced Optical Spring.

We propose and experimentally demonstrate the generation of enhanced optical springs using the optical Kerr effect. A nonlinear optical crystal is inserted into a Fabry-Perot cavity with a movable mirror, and a chain of second-order nonlinear optical effects in the phase-mismatched condition induces the Kerr effect. The optical spring constant is enhanced by a factor of 1.6±0.1 over linear theory. To our knowledge, this is the first realization of optomechanical coupling enhancement using a nonlinear optical effect, which has been theoretically investigated to overcome the performance limitations of linear optomechanical systems. The tunable nonlinearity of demonstrated system has a wide range of potential applications, from observing gravitational waves emitted by binary neutron star postmerger remnants to cooling macroscopic oscillators to their quantum ground state.

Fabry-perot interferometers with resin scaffolders for high sensitivity temperature sensing

This study explores the development of an innovative Fabry-Perot Interferometer (FPI) designed for temperature sensing and environmental monitoring. The device is constructed by embedding optical fibers within a 3D-printed resin scaffold, forming a structure with an open Fabry-Perot cavity. Intended as an integral component of Cyber-Physical-Social Systems (CPSS), this FPI structure aims to enhance the system’s capacity to sense changes in external environmental conditions. Within the CPSS context, the FPI offers several advantages, including simple manufacturing processes, low production costs, and high sensitivity. These benefits contribute to providing precise environmental feedback to the system, which is essential in implementing effective security and privacy protection strategies. Experimental evaluations have shown that the FPI exhibits a high linear sensitivity of 14.330 nm/°C within a temperature range of 34.9°C–38.5°C, confirming its potential for application in CPSS for temperature monitoring and environmental sensing.

Multifunctional beam modulation based on gratings combined with additive metasurfaces

A design scheme combining grating and element additive metasurface is proposed in this paper. Multi-dimensional joint control of the phase, amplitude, angle and polarization and multi-functional integrated metasurface applications were realized by using the inherent characteristics of the light wave properties (polarization and wavelength). Firstly, suitable structural parameters are obtained based on the reflection response of the unit structure, and a 2-bit encoded metasurface array is constructed by utilizing the combinatorial operation between the unit structure. Combined with the polarization selectivity of the lower grating, the dual-function integration of asymmetric transmission (the contrast ratio is 98%) and abnormal reflections (operating bandwidth is 300 nm) was realized. Next, two new half-wave plates were obtained by addition and rotating the elemental structure, and the polarization conversion efficiency of 95%–97% was achieved thanks to the Fabry–Perot cavity formed by the upper metasurface and lower grating. Finally, encoded metasurface based on the geometric phase principle to achieve 300 nm bandwidth cross-polarized wave deflection characteristics with polarization conversion efficiency close to 100%. Our work combines grating structures with element additive metasurfaces, which solves the problem that element structure needs to be redesigned with the change of function, and also paves the way for the application of multifunctional integrated metasurfaces in optical sensing, optical imaging and other fields.

Super-resolution spectroscopy via spectrum slicing with a Fabry–Perot cavity

Spectroscopy is one of the most powerful technical tools that are widely used in the study of natural sciences and the development of high technologies. To improve the performance of a traditional dispersive spectrometer, there is a competition between its spectral resolution and the geometric volume; a higher resolution is usually accompanied by a higher cost as well. However, a growing body of evidence suggests an urgent demand for miniaturized spectrometers with high spectral resolution and low costs. In this paper, we propose and study super-resolution spectroscopy via spectrum slicing by use of a Fabry–Perot (FP) cavity combined with a traditional spectrometer. The cavity functions as a spectral filter to slice into discrete pieces the continuous spectrum of the input light. For each given cavity length, the cavity outputs a set of sliced spectral pieces that are then analyzed and recorded by the subsequent spectrometer. By scanning the cavity length, one will have multiple sets of sliced spectral pieces that are then finally fused to recover a resolution-enhanced copy of the input spectrum. A theoretical analysis for the super-resolution spectroscopy is provided to prove the feasibility of the proposal, as further confirmed by MATLAB numerical simulation. The studied spectral analysis technique will benefit the research fields in need of high resolution spectrometers with moderate device volumes and low costs.

Ultrasensitive optomechanical strain sensor

We demonstrate an ultrasensitive optomechanical strain sensor based on a SiN membrane and a Fabry-Perot cavity, enabling the measurements of both static and dynamic strain by monitoring reflected light fluctuations using a single-frequency laser. The SiN membrane offers high-quality-factor mechanical resonances that are sensitive to minute strain fluctuations. The two-beam Fabry-Perot cavity is constructed to interrogate the motion state of the SiN membrane. A static strain resolution of 4.00 nɛ is achieved by measuring mechanical resonance frequency shifts of the SiN membrane. The best dynamic resolution is 4.47 pɛHz-1/2, which is close to that of the sensor using high-finesse cavity and optical frequency comb, overcoming the dependence of ultrasensitive strain sensors on narrow-linewidth laser and high-finesse cavity with frequency locking equipment. This work opens up a promising avenue for a new generation of ultrasensitive strain sensors.

Design of a multi-physics coupling MEMS pressure sensor

The pressure measurement of explosion shock wave puts forward high requirements on the temperature resistance and response speed of the sensor. In this paper, a multi-physics coupling pressure sensor is designed to meet requirements. The sensor mainly consists of a Fabry-Perot cavity optical fiber sensing unit, a piezoelectric pressure sensing unit and a thermometric resistance temperature measurement module. Firstly, the structure of the sensor is designed. The top and bottom surfaces of the Fabry-Perot cavity are composed of a silicon diaphragm and a quartz glass. The piezoelectric pressure sensing unit is an AlN film including its electrodes. Pt thermometric resistance is developed to realize real-time temperature monitoring. Secondly, the fabrication process of the sensor is discussed, especially three key technologies. An Al film is sputtered to increase the reflectivity of the quartz glass. The SU-8 photoresist is applied to accurately control the thickness of Fabry-Perot cavity. Etching is adopted to work out the graphics of the AlN piezoelectric film. At last, a complete fabrication process of the sensor is described. The fabrication of multilayer films begins with a double-sided polishing silicon wafer, while Fabry-Perot cavity was from a double-sided polishing quartz glass. Then two parts of the sensor are combined to ensure the multi-physics coupling sensor to achieve complete function.

A high gain and high radiation efficiency optical transparent Fabry–Perot cavity antenna

AbstractThis letter proposes a novel high gain, high efficiency optically transparent Fabry–Perot Cavity antenna operating in millimetre‐wave. The antenna employs dual layers of transparent partially reflective surface and a transparent artificial magnetic conductor structure to enhance the gain and gain bandwidth. The reflection amplitude and phase have a low sensitivity to the sheet resistance of the transparent materials, which greatly reduce the requirement for the conductivity of transparent material and simplify the manufacturing process. The size of the antenna is 3.47λ0 × 3.47λ0 × 0.68λ0. A peak gain of 14.2 dBi, peak radiation efficiency of 67.1% and optical transparency of 81% are achieved.