Environmental Dust Particles Research Articles

Study on the deposition rates of inhaled dust in respiratory tract by anchor excavation driver during coal mining

The external flow field of roadheader in Daliuta Coal Mine is numerically simulated, and breathing process of drivers is experimented in this paper. The airflow field of the whole tunnel is divided into three parts. The wind speed in the breathing area is determined to be 1.8 m/s. The relationship between dust concentration and time in respiration area is y = -0.0357x2 + 8.5541x-1.2298. The condition concentration of dust capture test is 81–508 mg/m3. The experimental results show that the D90 and D50 of environmental and bionic throat dust particles decrease with the increase of dust concentration. The increase of environmental dust concentration has a greater impact on dust with particle size larger than 6.5 μm. Dust concentration (ppm) inhaled by the driver = 0.057* Dust concentration in the environment (mg/m3). This study is expected to provide theoretical support for the prevention and control of dust occupational hazards.

Effect of The Different Types of Dust on The Performance of Photovoltaic Panels in Iraq

Iraq is characterized by an atmosphere that contains dust particles most of the time. In this study, a detailed investigation was conducted on the effect of dust particles of different types on the performance of the photovoltaic (PV) model. Data were collected for samples of four types of dust (chalk powder, brick powder, Sand, Cool powder) and different weights (30,60,90 and 120 g/m2) with the change in the energy loss of the PV module at four levels of solar radiation (500, 600, 700 and 800 W/m2). In this study the effect of environmental dust particles on energy loss as well as electrical efficiency was evaluated. The minimum and maximum power value of (43.58, 101.95W) respectively, was observed during dust accumulation on the photovoltaic unit. It was also noted that the efficiency and power were inversely proportional to the increase in weight and directly to the size of the dust particles.

Disease modeling and drug screening using human airway organoids: a systematic review

Increasing levels of fine environmental dust particles due to industrialization and emerging respiratory illnesses, such as coronavirus disease 2019, pose serious threats to human life. The use of organoids for disease modeling and drug screening has been proposed as a new treatment approach for respiratory diseases. As discussed in this review, various pathogen models, genetic disease models, and patient-derived lung cancer organoid models have been reported for disease modeling and drug testing using human airway organoids. Despite these promising recent advances, several issues must be addressed before the disease modeling potential of human airway organoids can be fully realized. If systematic methods to produce mature airway organoids can be developed, and reproducible organoid models can be implemented using standardized protocols, airway organoids will likely become valuable respiratory disease models and drug screening tools.

On the Mechanism of Human Saliva Interaction with Environmental Dust in Relation to Spreading of Viruses.

Environmental effects such as dust mitigation can amplify the spread of viruses via inhaling infected dust particles. Infusion and the spreading rate of human saliva over the dust particles can play a critical role in contiguous virus spread. In the present study, mechanical and chemical interactions of human saliva with environmental dust particles are considered. The saliva droplet impact on dust particles is examined while mimicking saliva droplet spreading during coughing in a dusty ambience. The mechanisms of saliva infusion and cloaking on the dust particles are explored. The characteristics of saliva droplet normal and oblique impacts on a dust particle are examined experimentally and numerically to evaluate the amount of saliva residues on the impacted particle surface. The findings reveal that the saliva liquid infuses and cloaks the dust particle surfaces. The saliva droplet impact on the dust particles leaves a considerable amount of saliva residues on the impacted surfaces, which remain undried for a prolonged period in indoor environments. Weak adhesion of the saliva-infected dust particles on surfaces, such as glass surfaces, enables saliva-infected dust particles to rejoin neighboring ambient air while possessing a high potential for virus spreading.

Sliding Water Droplet on Oil Impregnated Surface and Dust Particle Mitigation.

Self-cleaning of surfaces becomes challenging for energy harvesting devices because of the requirements of high optical transmittance of device surfaces. Surface texturing towards hydrophobizing can improve the self-cleaning ability of surfaces, yet lowers the optical transmittance. Introducing optical matching fluid, such as silicon oil, over the hydrophobized surface improves the optical transmittance. However, self-cleaning ability, such as dust mitigation, of the oil-impregnated hydrophobic surfaces needs to be investigated. Hence, solution crystallization of the polycarbonate surface towards creating hydrophobic texture is considered and silicon oil impregnation of the crystallized surface is explored for improved optical transmittance and self-cleaning ability. The condition for silicon oil spreading over the solution treated surface is assessed and silicon oil and water infusions on the dust particles are evaluated. The movement of the water droplet over the silicon oil-impregnated sample is examined utilizing the high-speed facility and the tracker program. The effect of oil film thickness and the tilting angle of the surface on the sliding droplet velocity is estimated for two droplet volumes. The mechanism for the dust particle mitigation from the oil film surface by the sliding water droplet is analyzed. The findings reveal that silicon oil impregnation of the crystallized sample surface improves the optical transmittance significantly. The sliding velocity of the water droplet over the thick film (~700 µm) remains higher than that of the small thickness oil film (~50 µm), which is attributed to the large interfacial resistance created between the moving droplet and the oil on the crystallized surface. The environmental dust particles can be mitigated from the oil film surface by the sliding water droplet. The droplet fluid infusion over the dust particle enables to reorient the particle inside the droplet fluid. As the dust particle settles at the trailing edge of the droplet, the sliding velocity decays on the oil-impregnated sample.

Carbonated water droplets on a dusty hydrophobic surface.

Dust mitigation from surfaces remains essential, particularly for the efficient operation of energy harnessing devices. Although various dust removal methods have been introduced, the self-cleaning method is favorable because of the cost-effective cleaning process. Dust mitigation from surfaces by water droplets, mimicking nature, is fruitful because it involves low-cost operations. The dust removal rate from surfaces by rolling water droplets can be increased by creating bubbles inside the rolling droplets through which dust pinning on surfaces can be lowered and the droplet liquid infusion on dust surfaces can be enhanced. This study provides insight into bubble formation and dust mitigation in carbonated and distilled water droplets located on hydrophobic surfaces by examining bubble formation and dust distribution inside the water droplets. The behavior of bubbles inside the carbonated water droplet and emanating from the hydrophobic surface was recorded and analyzed by incorporating high-speed camera data. The influence of environmental dust particles on bubble formation was also assessed. Bubble velocity was formulated analytically and the findings are compared with those of the experimental values. Findings revealed that the bubble formation inside the carbonated droplet fluid had a significant effect on the transition of dust particles from the hydrophobic surface towards the droplet fluid. The volume concentration of dust particles in the carbonated water droplet was almost 1.5 to 2.5 times larger than that of the distilled water droplet. The dissolution of alkaline and alkaline earth metal compounds in the carbonated droplet fluid acted like nucleation centers for bubble formation; hence, the number of bubbles formed on the dusty hydrophobic surface was greater than that of the clean hydrophobic surface. Some bubbles attached at the dust particle surface contributed to dust mobility in the droplet fluid, which occurred particularly in the droplet bottom region. This enhanced the velocity of the dust particles transiting from the dusty hydrophobic surface to the droplet fluid interior by almost 1.5 times in the early period.

Environmental Dust Particles Repelling from A Hydrophobic Surface under Electrostatic Influence

Environmental dust particles repelling from a hydrophobic surface under the electrostatic influence are considered and the dynamics of the dust particles are analyzed incorporating the high speed camera. The velocity of the repelled dust particles are formulated using the force balance incorporating the forces associated with the electrostatic repulsion, particle adhesion, particle drag, and the inflight particles interaction under the charge influence. The functionalized silica particles are deposited on the glass surface towards achieving a hydrophobic wetting state on the surface. An electronic circuitry is designed and built while generating the electrostatic effect, in the pulse form, on the dust particles located on the surface of the hydrophobic plate. Findings revealed that functionalized silica particles deposited surface results in hydrophobic wetting state with contact angle in the order of 158° ± 2° and contact angle hysteresis of 2° ± 1°. The electrostatic impulsive force generated on the plate surface enables to repel most of the sizes of the dust particles; however, some of the small dust particles remain as the residues on the surface after the electrostatic influence. The dust particle velocity predicted from the analytical formulation agrees with that obtained from the high speed camera data. The pinning force of the small size particles (0.6 µm≤), due to adhesion on the surface, is found to be larger than the average size particles (∼1.2 µm), which in turn, suppresses these particles repelling from the surface under the electrostatic influence. The residues of the dust particles on the as received glass surface after dust repelling are more than those residues on the hydrophobic surface. This behavior is associated with the dust particles adhesion on the surface. Consequently, hydrophobic wetting state on the plate surface improves the dust particle repelling from the surface.

An Assessment of Thermoset Injection Molding for Thin-Walled Conformal Encapsulation of Board-Level Electronic Packages

An ever-growing market demand for board (second) level packages (e.g., embedded systems, system-on-a-chip, etc.) poses newer challenges for its manufacturing industry in terms of competitive pricing, higher reliability, and overall dimensions. Such packages are encapsulated for various reasons including thermal management, protection from environmental conditions and dust particles, and enhancing the mechanical stability. In the due course of reducing overall sizes and material saving, an encapsulation as thin as possible imposes its own significance. Such a thin-walled conformal encapsulation serves as an added advantage by reducing the thermo-mechanical stresses occurring due to thermal-cyclic loading, compared to block-sized or thicker encapsulations. This paper assesses the encapsulation process of a board-level package by means of thermoset injection molding. Various aspects reviewed in this paper include the conception of a demonstrator, investigation of the flow simulation of the injection molding process, execution of molding trials with different encapsulation thicknesses, and characterization of the packages. The process shows a high dependence on the substrate properties, injection molding process parameters, device mounting tolerances, and device geometry tolerances. Nevertheless, the thermoset injection molding process is suitable for the encapsulation of board-level packages limiting itself only with respect to the thickness of the encapsulation material, which depends on other external aforementioned factors.

Water droplet on inclined dusty hydrophobic surface: influence of droplet volume on environmental dust particles removal.

A water droplet's behavior on an inclined hydrophobic surface in the presence of environmental dust particles is considered and the droplet's dynamics are analyzed pertinent to self-cleaning applications. A polycarbonate wafer is crystallized using the solution-crystallization method to generate hierarchically distributed micro/nano-sized spherules and pillars on the surface. To improve the wetting state and lower the contact angle hysteresis, functionalized silica particles are synthesized and, later, deposited on the crystallized surface. Environmental dust particles are collected and characterized in terms of elemental composition, size and shape. A high-speed camera is used to monitor a water droplet's behavior on the inclined hydrophobic surface with and without the presence of dust particles. The influence of droplet volume on the dust particle removal rate from the inclined hydrophobic surface is assessed. It is found that the functionalized silica particles deposited on the surface result in a droplet contact angle in the order of 158 ± 2° and contact angle hysteresis of 2 ± 1°. The water droplet mainly rolls on the inclined hydrophobic surface and the sliding velocity remains almost 13% of the transverse velocity of the droplet. Droplet wobbling is influenced by the dust particles and the droplet size; in which case, increasing the droplet volume enhances the droplet puddle thickness on the hydrophobic surface. The cloaking of the droplet fluid onto the dust particles causes mixing of the dust particles with the droplet fluid while enhancing the particle removal from the hydrophobic surface. Increasing the droplet volume slightly enhances the size of the area of the cleaned surface.

Laser texturing of Inconel 718 alloy surface: Influence of environmental dust in humid air ambient

Laser texturing of Inconel 718 alloy surface under high nitrogen gas pressure is considered and the resulting surface morphology and wetting state are examined. Analytical tools are used to characterize the laser textured surface. Environmental dust particles and liquid solution formed from the water condensate on the dust particles in humid air ambient are analyzed. The tangential force required to remove the dried liquid solution from the laser textured and as received surfaces are measured incorporating the micro-tribomoter. It is found that laser treatment results in micro/nano size pillars on the textured surface and forms nitride compounds on the surface. This, in turn, modifies the wetting state of the workpiece surface from hydrophilic to hydrophobic. A liquid solution is formed due to the dissolution of alkaline and alkaline earth metals of the dust particles into the water condensate in humid air ambient. The liquid solution has high pH and forms different sizes of crystals on the surface upon drying. The liquid solution spreads on the textured surface while forming a film. It adheres strongly to the surface upon drying; in which case, the tangential force required removing the dried liquid from the surface remains high, which is more pronounced for the as receive surfaces.

Water Droplet Dynamics on a Hydrophobic Surface in Relation to the Self-Cleaning of Environmental Dust

The dynamic motion of a water droplet on an inclined hydrophobic surface is analyzed with and without environmental dust particles on the surface. Solution crystallization of a polycarbonate surface is carried out to generate a hydrophobic surface with hierarchical texture composed of micro/nanosize spheroids and fibrils. Functionalized nanosize silica particles are deposited on the textured surface to reduce contact angle hysteresis. Environmental dust particles are collected and characterized using analytical tools prior to the experiments. The droplet motion on the hydrophobic surface is assessed using high-speed camera data, and then, the motion characteristics are compared with the corresponding analytical results. The influence of dust particles on the water droplet motion and the amount of dust particles picked up from the hydrophobic surface by the moving droplet is evaluated experimentally. A 40 μL droplet was observed to roll on the hydrophobic surface with and without dust particles, and the droplet slip velocity was lower than the rotational velocity. The rolling droplet removes almost all dust particles from the surface, and the mechanism for the removal of dust particles from the surface was determined to be water cloaking of the dust particles.

Environmental dust removal from inclined hydrophobic glass surface: avalanche influence on dynamics of dust particles.

The removal of environmental dust particles from optically transparent glass surfaces is considered, and the dynamics of the dust particles on the inclined hydrophobic glass surface is examined. The glass surfaces are coated by functionalized nano-sized silica particles to create a hydrophobic wetting state on the surface. A thin layer of environmental dust particles, collected from the local area of Dammam in the Kingdom of Saudi Arabia (KSA), is deposited on the surface while mimicking the dust accumulation on the surfaces in the dusty days of KSA. In order to increase the removal rate of the dust particles from the inclined hydrophobic glass surfaces, high density particles, which are higher than the density of the dust particles, are locally distributed on the dust particle-deposited surface while generating the avalanche influence on the inclined surface. The motion of the dust and high density particles on the inclined surface is monitored using a high speed camera. The predictions of the dust particles' acceleration and velocity are compared to those obtained from the high speed camera data. It is found that the predictions of velocity and acceleration of the dust particles agree well with the experimental data. Local insertion of the high density particles generates avalanche influence on the inclined surface while initiating the removal of the dust particles from the hydrophobic surface at small inclination angles. The size of the area where the dust particles are removed from the inclined surface increases with enlarging coverage area of the high density particles. The dust-removed surface, under the avalanche influence, improves the UV-visible transmittance of the hydrophobic glass.

Effect of environmental dust particles on laser textured yttria-stabilized zirconia surface in humid air ambient

Zirconium nitride is used as a selective surface for concentrated solar heating applications and one of the methods to form a zirconium nitride is texturing of zirconia surface by a high intensity laser beam under high pressure nitrogen gas environment. Laser texturing also provides hydrophobic surface characteristics via forming micro/nano pillars at the surface; however, environmental dust settlement on textured surface influences the surface characteristics significantly. In the present study, laser texturing of zirconia surface and effects of the dust particles on the textured surface in a humid air ambient are investigated. Analytical tools are used to assess the morphological changes on the laser textured surface prior and after the dust settlement in the humid air ambient. It is found that laser textured surface has hydrophobic characteristics. The mud formed during condensate of water on the dust particles alters the characteristics of the laser textured surface. The tangential force required to remove the dry mud from the textured surface remains high; in which case, the dried liquid solution at the mud-textured surface interface is responsible for the strong adhesion of the dry mud on the textured surface. The textured surface becomes hydrophilic after the dry mud was removed from the surface by a desalinated water jet.

An experimental study on effect of dust on power loss in solar photovoltaic module

In the present study, a detailed investigation on air dust particles effect on photovoltaic (PV) model performance has been carried out. The scanning electron microscope analysis of the collected dust samples was being carried out, and the obtained images were being analyzed in order to observe the character and topography of the dust sample particles. The data for dust samples of different weights with change in power loss in a PV module at three solar irradiations levels of 650, 750 and 850 W/m2 have been collected. In present study, the effect of environmental dust particles on power loss in PV module has been evaluated by measuring the electrical performance index such as voltage, current and power. The minimum power value of 3.88 W has been observed during the accumulation of rice husk on PV module.

Characteristics of oil impregnated hydrophobic glass surfaces in relation to self-cleaning of environmental dust particles

Maintaining the high performance of photovoltaic devices requires regular cleaning of panel surfaces because of the environmental dust settlements in harsh weather conditions. Self-cleaning characteristics of such surfaces are vital for the cost effective operations. In the present study, a new fabrication approach is introduced towards self-cleaning applications of optically transparent glasses. In the fabrication process, self-assembly monolayer of silane was coated on the silica nanoparticle layer, prior to oil impregnation, to improve oil hydrodynamic stability of the oil film on the surface. The static water contact angle, sliding angle and average optical transmittance of the resulting surfaces are measured. The scanning electron microscope and atomic force microscope are used to reveal the hierarchical morphology of the surface. Dust cleaning tests are performed to evaluate the self-cleaning characteristics of the surfaces. The findings revealed that the water droplets can be effectively used to remove almost all of the dust particles from the surfaces. Oil impregnation improved the optical transmittance of the treated hydrophobic glass surface.

Silicone oil impregnated nano silica modified glass surface and influence of environmental dust particles on optical transmittance

The behavior of environmental dust particles on a silicone oil impregnated glass surface is examined in relation to optical transparent surfaces for self-cleaning applications.

Internal fluidity of a sessile droplet with the presence of particles on a hydrophobic surface

ABSTRACTThermocapillary flow inside a sessile droplet is considered in relation to microsized particles, resembling the environmental dust particles’ removal from the hydrophobic surface. Polycarbonate surface is textured through solution-induced crystallization to generate surfaces with hydrophobic characteristics. The dusts are collected from the local environment and characterized using the analytical tools. Internal fluidity of the droplet is simulated numerically in line with the experimental conditions. An experiment is carried out to measure the velocity of the dust particles using the optical microscopic system. It is found that thermocapillary-induced forces generate counter-rotating cells in the droplet, which depends on the droplet contact angle. The percentage of dust particles removed from the hydrophobic surface into the droplet, due to droplet internal fluidity, increases with the size of the dust particles and it remains almost constant with progressing time. The dust particles follow the streamlines in the circulation cells inside the droplet.

Chemo-Mechanical Characteristics of Mud Formed from Environmental Dust Particles in Humid Ambient Air.

Mud formed from environmental dust particles in humid ambient air significantly influences the performance of solar harvesting devices. This study examines the characterization of environmental dust particles and the chemo-mechanics of dry mud formed from dust particles. Analytical tools, including scanning electron microscopy, atomic force microscopy, energy dispersive spectroscopy, particle sizing, and X-ray diffraction, are used to characterize dry mud and dust particles. A micro/nano tribometer is used to measure the tangential force and friction coefficient while tensile tests are carried out to assess the binding forces of dry mud pellets. After dry mud is removed, mud residuals on the glass surface are examined and the optical transmittance of the glass is measured. Dust particles include alkaline compounds, which dissolve in water condensate and form a mud solution with high pH (pH = 7.5). The mud solution forms a thin liquid film at the interface of dust particles and surface. Crystals form as the mud solution dries, thus, increasing the adhesion work required to remove dry mud from the surface. Optical transmittance of the glass is reduced after dry mud is removed due to the dry mud residue on the surface.

Expression of interleukin (IL)-5 and IL-9 receptors on neutrophils of horses with heaves

Heaves, a condition associated with airway neutrophilia, is believed to result from an allergic response to environmental dust particles. However, the contribution of neutrophils to the allergic response is poorly understood. It has been hypothesized that Th2-type cytokines can directly activate neutrophils to produce pro-inflammatory mediators. The present study focused on the presence of receptors for the Th2-type cytokines interleukin (IL)-5 and IL-9 on peripheral blood neutrophils of horses with heaves. Neutrophils were isolated from peripheral blood of horses with heaves ( n = 7), and normal control ( n = 5) before (pasture) and 3 weeks following a continuous natural allergen challenge (stabling). Horses with heaves had significantly increased numbers of neutrophils expressing IL-5 and IL-9 receptors compared to control while in pasture, and further increased during stabling in heaves affected horses but not in control animals. These results provide a possible mechanism by which Th2-type cytokines may activate neutrophils in equine heaves.

Similarity in seasonal appearance between atmospheric birch-pollen grains and allergen in paucimicronic, size-fractionated ambient aerosol.

Specific allergen from various pollen types has been found to be carried through the outdoor air, not only by intact pollen grains, but also by much smaller, paucimicronic particles. There is no complete agreement on whether, for birch (Betula), the seasonal appearance of atmospheric pollen allergen follows the fluctuation pattern of the pollen season. Assessment of birch-pollen allergen in size-fractionated ambient aerosol was performed by descending elution of allergen from impaction strips of a five-stage cascade impactor, and compared with atmospheric birch-pollen concentrations as measured with a volumetric pollen trap. An overall similarity in the courses of the seasonal presence was found for both birch pollen and allergen in particles of all paucimicronic size fractions, although some airborne allergen was detected before and after the birch-pollen season. Transfer of pollen allergen to both natural and pollutant environmental dust particles is thought to be the probable explanation of secondary allergen carriage by paucimicronic particles. Until simple techniques for direct and rapid assessment of atmospheric pollen allergen become available, the pollen count gives sufficiently reliable information about the seasonal course of airborne pollen allergen.