Electromechanical Coupling Research Articles

Innovative surface acoustic wave devices: A solution for real time monitoring and self-cleaning cascade impactor

This paper presents a comparative study of three types of surface acoustic waves sensors used for particulate matter detection along with a theoretical study tackling the possibility to switch to innovative materials called Piezoelectric-on-Insulator. These sensors are placed in a cascade impactor as impaction plates. Monitoring their phase variation allows us to measure the quantity of fine particles present in the air with high accuracy. Until now, the sensors used in our prototype are built on quartz substrate and present a sufficient sensitivity to fine particles. One major concern in our application is the fouling of the sensor’s surface with particles upon long periods of exposure. This shaped our drive to develop a self-cleaning sensor relying on other substrates with stronger electromechanical coupling coefficient (k2) [1]. Hence, the aim of this study is to demonstrate the possibility of using strongly coupled modes on different piezoelectric substrates for an accurate PM detection. Among these, different POI substrates are considered to assess their physical and acoustic properties, especially in terms of k2 and thermal stability, for further optimization enabling their exploitation in the self-cleaning system that is being developed.

Electric–Mechanical coupling analysis of two-dimensional piezoelectric heterogeneous materials in flexible electric devices with extended multiscale isogeometric analysis

Piezoelectric heterogeneous materials are widely used in flexible electronic device design, enhancing sensitivity to external stimuli like pressure and acceleration. Despite their usefulness, analyzing these inherently periodic structures poses significant computational challenges. In response, this paper presents a multiscale isogeometric analysis approach tailored for simulating piezoelectric materials. We introduce an electric–mechanical coupling model using isogeometric analysis (IGA) for two-dimensional piezoelectric membrane structures, assuming the plane stress hypothesis. Our proposed algorithm enables precise calculation of both displacement and electric potential solutions, demonstrating superior convergence properties compared to traditional finite element methods. Furthermore, we extend this approach to multiscale isogeometric analysis for computing numerical solutions in porous structures and heterogeneous composite piezoelectric materials under tensile and bending conditions. Through rigorous numerical testing, we evaluate the proposed extended multiscale isogeometric analysis method, showcasing its efficacy in achieving a balance between computational efficiency and simulation accuracy. This IGA-based electro-mechanical coupling model and numerical algorithm pave the way for more streamlined and precise simulations of piezoelectric materials within the context of flexible electronic devices.

A High Q Lamb Wave Resonator with Dummy Toes Based on 20% ScAlN Film

Abstract The lamb wave resonator (LWR) based on aluminum nitride (AlN) films are preferred strategy for high-frequency filters in 5G communication due to the tunable electromechanical coupling and high Q value. However, since the low electromechanical coupling and piezoelectric coefficient of AlN films, conventional lamb filters are difficult to meet the requirements of high bandwidth and low loss. This work proposes a lamb wave resonator with dummy toes (DT-LWR) based on scandium-doped aluminum nitride (ScAlN) film to improve the quality factor(Q) meanwhile suppress the spurious modes. The processed DT-LWR was tested using a vector network analyser (VNA, Keysight N5222B), and the MBVD model was used to fit the Z parameters. The Q value of DT-LWR is 1437.23, while that of LWR is 1250.09. It is increased by 14.97%. The enhancements make the DT-IWR as an ideal for filters with minimal insertion loss.

High Sensitivity Performance of Piezoelectric Micromachined Ultrasonic Transducer Employing Sc-Doped AlN Thin Film

Abstract Aluminum Nitride (AlN) based piezoelectric micromachined ultrasonic transducers (PMUTs) have been the prime choice in acoustic imaging, because it has advantages of high frequency and thus high resolution. However, low piezoelectric constants of AlN gives rises to limitation in transmitting sensitivity. Scandium (Sc) doping method for AlN can be used to improve its piezoelectricity. In this paper, single element PMUT based on ScAlN thin film was proposed and modeled by performing finite element method (FEM). Influence of different electrode configurations on PMUT performance were studied. The results show that, compared with other electrode configurations, PMUT has the best overall performance when the upper electrode is platinum (Pt) and the lower electrode is molybdenum (Mo). In addition, the acoustic field characteristics and its dynamic analysis of PMUT based on ScAlN in water were studied. The investigation results demonstrated that the relative pulse-echo sensitivity level M of PMUT is significantly improved with the increase of Sc doping concentration in AlN thin film. When the Sc concentration is 40%, the M reaches -44 dB, which is 20 dB higher than that without Sc (-64 dB). The PMUT based on the high Sc-doped AlN thin film has a larger effective electromechanical coupling coefficient and sensitivity, which is beneficial to the application in high sensitivity ultrasound imaging.

Enhancing the piezoelectric performance of novel PZT-PMS-PSN piezoelectric ceramics by fine-tuning the monoclinic phase

The enhanced high-power performance of 0.93 Pb(Zr1-xTix)O3-0.05 Pb(Mn1/3Sb2/3)O3-0.02 Pb(Sc1/2Nb1/2)O3 (x = 0.48, 0.50, 0.52, 0.54, 0.56) piezoelectric ceramics (PZT-PMS-PSN) has been achieved with notable improvement in the piezoelectric coefficient (d33). The presence of the monoclinic phase (Cc) has led to an increase in d33 from 214 pC N−1 to 315 pC N−1. Therefore, the composition 0.93 Pb(Zr0.48Ti0.52)O3-0.05 Pb(Mn1/3Sb2/3)O3-0.02 Pb(Sc1/2Nb1/2)O3 exhibits excellent mechanical and electrical parameters: a d33 value of 315 pC N−1, a high mechanical quality factor of 1578, an electromechanical coupling factor kp of 52 %, and a low dielectric loss tanδ of only 0.288 %. Additionally, this ceramic exhibits a significantly high Curie temperature (Tc), reaching up to 328 °C which stabilizes its ferroelectric phase. Moreover, the phase transition of PZT-PMS-PSN ceramics from rhombohedral to tetragonal phase was investigated by X-ray diffraction, Raman scattering, Piezo-response force microscopy.

High Order Rayleigh-Type SAW Devices for Advanced 5G Front-ends with Improved Performance

Abstract This paper presents a piezoelectric layered structure composed of a rotated LiNbO3 thin film combined with a diamond film for improved comprehensive performance SAW devices. Theoretical analysis of SAW resonator on the proposed structure is performed to calculate its SAW characteristics including electromechanical coupling coefficient (K2 ), frequency (f), and quality factor (Q). It is found that a high-order Rayleigh mode is effectively excited and exhibits not only high frequency but also large K2 and high Q. The influences of the Euler angles, layer stack configurations of LiNbO3, and the electrode on the SAW properties are investigated systematically to optimize the device performance of the proposed structure. The results show the resonator can operate at frequency of 6.6 GHz with a large K2 of 13.58% and high Q of 2134, which makes the proposed layered structure a good potential solution for high-performance wideband SAW filters operating over 5 GHz.

Maximum Bandwidth Analysis With a Universal AWLR‐Based Filter Structure

ABSTRACTThe bandwidth enhancement of the acoustic‐wave‐lumped‐element resonator (AWLR)‐based filter has been investigated for a long time. However, few researches are focused on the maximum bandwidth analysis. Based on a universal circuit structure of the AWLR‐based filter, we proposed the maximum bandwidth analysis of the hybrid filter. In the analysis process, the universal filter structure can be transformed into a novel AWLR‐based filter structure by incidentally excluding most of the other structures (including the reported hybrid filter structures) under the defined electrical characteristics. The novel hybrid filter obtains the maximum fractional bandwidth (FBW). Moreover, the proposed calculation results are better than the simulation results without artificial intervention. They are 2.12kt2 and 1.63kt2, respectively. kt2 is the electromechanical coupling coefficient of the acoustic wave resonator (AWR). Third‐order AWLR‐based bandpass filters with five‐type circuit structures have been manufactured and measured. They include the proposed novel AWLR‐based filter and the hybrid filter with the reported structure based on the universal AWLR‐based filter structure. The experimental results indicate that the proposed novel AWLR‐based filter has the maximum FBW.

A novel compartmental approach for modeling stomach motility and gastric emptying

The stomach, a central organ in the Gastrointestinal (GI) tract, regulates the processing of ingested food through gastric motility and emptying. Understanding the stomach function is crucial for treating gastric disorders. Experimental studies in this field often face difficulties due to limitations and invasiveness of available techniques and ethical concerns. To counter this, researchers resort to computational and numerical methods. However, existing computational studies often isolate one aspect of the stomach function while neglecting the rest and employ computationally expensive methods. This paper proposes a novel cost-efficient multi-compartmental model, offering a comprehensive insight into gastric function at an organ level, thus presenting a promising alternative.The proposed approach divides the spatial geometry of the stomach into four compartments: Proximal/Middle/Terminal antrum and Pyloric sphincter. Each compartment is characterized by a set of ordinary differential equations (ODEs) with respect to time to characterize the stomach function. Electrophysiology is represented by simplified equations reflecting the “slow wave behavior” of Interstitial Cells of Cajal (ICC) and Smooth Muscle Cells (SMC) in the stomach wall. An electro-mechanical coupling model translates SMC “slow waves” into smooth muscle contractions. Muscle contractions induce peristalsis, affecting gastric fluid flow velocity and subsequent emptying when the pyloric sphincter is open. Contraction of the pyloric sphincter initiates a retrograde flow jet at the terminal antrum, modeled by a circular liquid jet flow equation.The results from the proposed model for a healthy human stomach were compared with experimental and computational studies on electrophysiology, muscle tissue mechanics, and fluid behavior during gastric emptying. These findings revealed that each “ICC” slow wave corresponded to a muscle contraction due to electro-mechanical coupling behavior. The rate of gastric emptying and mixing efficiency decreased with increasing viscosity of gastric liquid but remained relatively unchanged with gastric liquid density variations. Utilizing different ODE solvers in MATLAB, the model was solved, with ode15s demonstrating the fastest computation time, simulating 180 s of real-time stomach response in just 2.7 s. This multi-compartmental model signifies a promising advancement in understanding gastric function, providing a cost-effective and comprehensive approach to study complex interactions within the stomach and test innovative therapies like neuromodulation for treating gastric disorders.

Porous Structure Enhances the Longitudinal Piezoelectric Coefficient and Electromechanical Coupling Coefficient of Lead-Free (Ba0.85Ca0.15)(Zr0.1Ti0.9)O3.

The introduction of porosity into ferroelectric ceramics can decrease the effective permittivity, thereby enhancing the open circuit voltage and electrical energy generated by the direct piezoelectric effect. However, the decrease in the longitudinal piezoelectric coefficient (d33) with increasing porosity levels currently limiting the range of pore fractions that can be employed. By introducing aligned lamellar pores into (Ba0.85Ca0.15)(Zr0.1Ti0.9)O3, this paper demonstrates an unusual 22-41% enhancement in the d33 compared to its dense counterpart. This unique combination of high d33 and a low permittivity leads to a significantly improved voltage coefficient (g33), energy harvesting figure of merit (FoM33) and electromechanical coupling coefficient ( ). The underlying mechanism for the improved properties is demonstrated to be a synergy between the low defect concentration and high internal polarizing field within the porous lamellar structure. This work provides insights into the design of porous ferroelectrics for applications related to sensors, energy harvesters, and actuators.

Study of electromechanical coupling dynamical characteristics of the grinding robot joint transmission system

Study of electromechanical coupling dynamical characteristics of the grinding robot joint transmission system

Development of Highly Efficient Lamb Wave Transducers toward Dual-Surface Simultaneous Atomization.

Highly efficient surface acoustic wave (SAW) transducers offer significant advantages for microfluidic atomization. Aiming at highly efficient atomization, we innovatively accomplish dual-surface simultaneous atomization by strategically positioning the liquid supply outside the IDT aperture edge. Initially, we optimize Lamb wave transducers and specifically investigate their performance based on the ratio of substrate thickness to acoustic wavelength. When this ratio h/λ is approximately 1.25, the electromechanical coupling coefficient of A0-mode Lamb waves can reach around 5.5% for 128° Y-X LiNbO3. We then study the mechanism of droplet atomization with the liquid supply positioned outside the IDT aperture edge. Experimental results demonstrate that optimized Lamb wave transducers exhibit clear dual-surface simultaneous atomization. These transducers provide equivalent amplitude acoustic wave vibrations on both surfaces, causing the liquid thin film to accumulate at the edges of the dual-surface and form a continuous mist.

Enhanced piezoelectric properties of KNN-based ceramics by synergistic modulation of phase constitution, grain size and domain configurations

Despite significant advancements in KNN-based piezoelectric ceramics, controlling their grain size remains a challenge, impacting reproducibility of piezoelectric properties. Here, we address this issue by initially investigating the defect chemistry of a ternary system 0.96 K0.48Na0.52Nb0.96Sb0.04O3-0.04Bi0.5Na0.5ZrO3-ABO3 (KNNS-BNZ-ABO3). The ABO3 dopant not only influences the phase constitution, but also induces different charge compensation mechanisms, affecting the grain size and domain configurations of ceramics. Furthermore, the relationship between the grain size and the piezoelectric properties is investigated. The superior piezoelectric charge coefficient (d33) of 435 pC/N, ultra-high planar mode electromechanical coupling factor (kp) of 0.62 and preferable temperature stability are obtained in KNN-based ceramics with large grain size (∼50 μm) and hierarchical domain structures. Finally, we elucidated the intrinsic and extrinsic contribution of the grain size on piezoelectric properties of KNN-based piezoceramics based on Rayleigh analysis. Our work provides an effective paradigm for the development of lead-free piezoelectric ceramics for industrial applications.

Parametric Synthesis of Single-Stage Lattice-Type Acoustic Wave Filters and Extended Multi-Stage Design.

This study proposes a single-stage lattice-type acoustic filter using an analytical solution method for either a narrow passband filter or a wider passband filter using two kinds of parameter assignments in the Butterworth-Van Dyke (BVD) model. To achieve the goal of a large bandwidth or high return loss, two first-order all-pass conditions are used. For multi-stage lattice-type filters, the cost function is defined and design parameters are extracted by using pattern search, while the initial values are provided through single-stage design to shorten optimization time and allow convergence to a better solution. This method provides the S-parameter frequency response for the filter on the YX 42° cut angle of lithium tantalate (electromechanical coupling coefficient of about 6%) that can meet the system specifications as much as possible. Finally, the three-stage lattice-type was applied to various 5G bands with a fractional bandwidth of 2-5%, resulting in a passband return loss of 10 dB and an out-of-band rejection of 40 dB or more.

High-field complex parameters characterization of PMN-PT single crystal/epoxy 1–3 composites (φ = 0.4) under a high AC electric field with a varied intensity

It is essential to characterize the high-field properties of piezoelectric composites for their applications in ultrasonic transducers. This study involved the development of an experimental characterization system of piezoelectric impedance spectra and mechanical quality factors under high-field conditions to analyze the properties of PMN-PT piezoelectric single-crystal composites. The impedance spectra and mechanical quality factors of a [001]c-poled 0.69PMN-0.31PT single crystal/epoxy 1–3 composite disk with filling ratio φ = 0.4 under thickness resonance mode were tested at different driving voltages ranging from 1 to 120 Vpp to explore the influence of AC electric field on the material properties. By utilizing a theoretical approach, an evaluation was conducted on the variations in the material properties such as stiffness, permittivity, piezoelectric coefficient, and electromechanical coupling factor, along with respective loss factors. Our results suggest that as the AC electric field increases, the elastic modulus c33D and the mechanical quality factor Qm decrease, while the piezoelectric strain coefficient d33 and the electromechanical coupling factor kt increase. However, the dielectric coefficient ε33X does not show an obvious change in this field range. Furthermore, the elastic loss factor tanϕ, the dielectric loss factor tanδ33′, the piezoelectric loss factor tanθ33′, and the electromechanical coupling loss factor tanχt all increase, indicating that the loss of the piezoelectric composite becomes more evident as the AC electric field grows.

Mechanically induced built-in electric field in BCTZ nanostructures for piezocatalysis: Experiments and modeling

Ba(Ti0.80Zr0.20)O3–0.5(Ba0.7Ca0.3)TiO3 (BCTZ) piezoelectric nanofibers (NFs) and nanoparticles (NPs) were fabricated using electrospinning and sol-gel methods, respectively. The impact of BCTZ nanostructure on piezocatalysis was investigated, revealing that both poled NFs and NPs exhibit a piezocatalytic degradation rate of 2.8 × 10–2 min-1, which is significantly higher than their unpoled counterparts at 2.3 × 10–2 min-1 and 1.9 × 10–2 min-1, respectively. The enhanced piezocatalytic degradation rates of the poled BCTZ nanostructures are attributed to their superior piezoelectricity, resulting in larger built-in electric fields under external strain. Moreover, BCTZ NFs provide numerous active piezocatalytic reaction sites confined to the one-dimensional (1D) fibrous boundaries. Simulation results indicate that BCTZ NFs exhibit greater displacement and higher piezoresponse compared to nanoparticles, due to the electromechanical coupling effect facilitated by the 1D nanostructure. This study provides an efficient pathway to understanding the coupling mechanism between the poled built-in electric field and piezotronics.

A sandwich-structured 1-3 type piezoelectric composite material for enhancing reliability

This study proposes a sandwich structure 1-3 piezoelectric composite, incorporating flexible silicone rubber to enhance the thickness vibration mode of piezoelectric ceramics. Rigid aluminum nitride (AlN) is employed to bolster the mechanical stability of the composite. Utilizing equivalent parameter theory, we establish a mathematical model for the sandwich structure composite material. The impact of the piezoelectric phase size and the volume fraction of AlN on several performance parameters of the material are analyzed, including the thickness electromechanical coupling coefficient, density, sound velocity, and characteristic impedance. The sandwich structure piezoelectric composite was fabricated using the "cutting and filling" technique. Experimental outcomes reveal that this material demonstrates concentrated thickness vibration modes, with a thickness electromechanical coupling coefficient reaching as high as 0.72, a 16.6 % increase compared to traditional 1-3 piezoelectric composites. Results from thermal shock tests and tensile tests suggest that the sandwich structure 1-3 piezoelectric composite has considerable potential for use in highly reliable low-frequency receiving transducers.

Energy extraction potential from wave-induced ship motions using linear generators

This paper presents an assessment of the energy harvesting potential from wave-induced motions when producing electricity by linear generators installed on ships. The study estimates an upper maximum energy extraction potential by not considering the electro-mechanical coupling; neither is mechanical and electrical dissipation considered. The analysis of the harvested energy is made using simulated data in a case study investigating three different ships (by size). Specifically, the case study reveals that, in moderate to mildly severe sea states, the power harvested from the environment using linear generators may reach values around 1–2 kW/tons of seismic mass. Thus, it is unrealistic to imagine ship designs where linear generators are thought to provide a ship’s necessary propulsion power but, on the other hand, they may serve to supplement the main engine for auxiliary power generation.

Counter-rotating synchronization theory and experiment of tri-rotor actuated with dual-frequency considering adaptive global sliding mode control strategy

In petroleum drilling engineering, self-synchronous vibration screen with single-frequency actuation is difficult to implement the scheduled synchronous behavior caused by its invariance and instability of dynamic characteristics, which usually leads to reduction of the production efficiency. Hence, to solve the problem mentioned above, a dual-frequency counter-rotating synchronization control method among three exciters is presented by combining adjacent cross-coupling control (ACCC) structure with global sliding mode control (GSMC) theory. Firstly, motion differential equation of the vibration system in each direction is derived according to mathematical model of the tri-rotor vibration machine. Secondly, considering exponential reaching law and adaptive control algorithm, the adjacent cross-coupling controller and the vector controller of each induction motor are investigated to achieve the stable zero phase difference synchronization between double-frequency rotors. Subsequently, Runge-Kutta method is introduced to establish the electromechanical coupling control model and prove validity of the control theory. Meanwhile, it is also discussed that the rotors cannot obtain an ideal self-synchronization state since velocity of high-frequency motor is not strictly equal to twice that of low-frequency motor. Finally, based on the experimental test scheme, an experimental prototype related to controlled multi-rotor synchronization vibration system is designed independently, which further verifies the validity of theory and computer simulation. Research shows that the desirable synchronous state of the vibration system can be accurately controlled via the designed control strategy, and the control system can implement diversity of the dynamical characteristics, due to the existence of strong robustness.

Piezoelectric Impedance-based Structural Damage Identification Empowered with Tunable Circuitry Integration and Multi-objective Optimization based Inverse Analysis

Abstract The piezoelectric impedance-based technique is increasingly recognized for its promise in structural health monitoring and damage identification. Built upon their self-sensing actuation capability, piezoelectric transducers can be integrated to host structures to acquire the system-level impedance information in high frequency range with small wavelength. Furthermore, the frequency-sweeping harmonic excitations in impedance measurements lead to the potential for model-based inverse identification of damage location and severity. A major challenge in damage identification, however, is that the inverse analysis is generally underdetermined, as the measurement information may not be adequate to yield a unique solution. In this research, a new methodology of tunable sensing in conjunction with multi-objective optimization inverse analysis is established. Taking advantage of the two-way electromechanical coupling of piezoelectric transducers, tunable inductance is integrated into the measurement circuit. For the same damage scenario, by tuning the inductance to a series of values, a family of impedance measurements can be acquired. Meanwhile, the inverse analysis is cast into a multi-objective optimization problem, aiming at minimizing the difference between measurement and model prediction and achieving sparsity in damage index vector. A Q-learning based multi-objective particle swarm optimization is synthesized to reach a small yet diverse solution set. We report the circuitry integration details as well as the algorithm enhancement with systematic case investigations. It is validated that the new methodology with enriched measurement can produce smaller solution set encompassing the true damage scenario, thereby providing vital information for diagnoses and prognosis.

An analysis of abnormal vibration and noise caused by shaft coupling misalignment of high-speed train

This study conducts on-site testing and simulation analysis of the abnormal noise phenomenon generated during the operation of high-speed trains. The sound pressure characteristics in the cabin and the vibration of different vehicle components are recorded and subjected to comprehensive analysis. Test results indicate that significant abnormal noise occurs inside the cabin at the speed of 250 km/h, with frequencies of 87 Hz, 173 Hz, 259 Hz, and 346 Hz. Through sound source identification, vibration transmission analysis and theoretical derivation, it has been determined that the abnormal noise primarily originates from the transmission system, and it is further speculated that these abnormal vibrations and noises may be correlated with the shaft coupling misalignment within the transmission system. To verify the conjecture, a high-speed vehicle electromechanical coupling simulation model was established, incorporating the shaft coupling misalignment in the transmission system. The vibration characteristics of vehicle components were analyzed, confirming that shaft coupling misalignment leads to uneven meshing forces in gears, resulting in significant vibration and noise that affect the riding comfort of the vehicle. We propose replacing the shaft coupling to solve this problem, the test results showed that the abnormal vibration amplitudes of the transmission system at 87 Hz, 173 Hz, 259 Hz, and 346 Hz were significantly reduced after replacing the shaft coupling, and the amplitude of the corresponding frequencies on the cabin floor decreased by 91 %, 78 %, 98 %, and 66 %, respectively. The issue of abnormal noise has been effectively resolved.