Drop-casting Technique Research Articles

Synthesis, Characterisation and Antibacterial Properties of Silicone-Silver Thin Film for the Potential of Medical Device Applications.

Silver (Ag) particles have sparked considerable interest in industry and academia, particularly for health and medical applications. Here, we present the “green” and simple synthesis of an Ag particle-based silicone (Si) thin film for medical device applications. Drop-casting and peel-off techniques were used to create an Si thin film containing 10–50% (v/v) of Ag particles. Electro impedance spectroscopy (EIS), X-ray diffraction analysis (XRD), scanning electron microscopy (SEM), energy dispersive X-ray (EDX), and tensile tests were used to demonstrate the electrical conductivity, crystallinity, morphology-elemental, and mechanical properties, respectively. The oriented crystalline structure and excellent electronic migration explained the highest conductivity value (1.40 × 10−5 S cm−1) of the 50% Ag–Si thin film. The findings regarding the evolution of the conductive network were supported by the diameter and distribution of Ag particles in the Si film. However, the larger size of the Ag particles in the Si film resulted in a lower tensile stress of 68.23% and an elongation rate of 68.25% compared to the pristine Si film. The antibacterial activity of the Ag–Si film against methicillin-resistant Staphylococcus aureus (MRSA), Bacillus cereus (B. cereus), Klebsiella pneumoniae (K. pneumoniae), and Pseudomonas aeruginosa (P. aeruginosa) was investigated. These findings support Si–Ag thin films’ ability to avoid infection in any medical device application.

Salt Concentration Effect on Electrical and Dielectric Properties of Solid Polymer Electrolytes based Carboxymethyl Cellulose for Lithium-ion Batteries

Solid polymer electrolytes (SPEs) based carboxymethyl cellulose (CMC) with lithium perchlorate (LiClO4) were prepared via solution drop-cast technique. The CMC host is complexed by different concentrations of LiClO4 salt. SPEs were characterized by Electrochemical Impedance Spectroscopy (EIS) and Linear Sweep Voltammetry (LSV) in coin cells with lithium metal electrodes. EIS performed unique results based on various ionic conductivity values and dielectric properties. The higher ionic conductivity (1.32 × 10-5 S/cm) was obtained by SPEs 2 following by short-range ionic transport results based on dielectric properties depending on frequency. SPEs with LiClO4 addition are electrochemically stable over 2 V in lithium battery coin cells from LSV results.

H-BN nanosheets obtained by mechanochemical processes and its application in lamellar hybrid with graphene oxide

Nowadays, hexagonal boron nitride nanosheets (h-BNNS) have shown promising results among 2D nanomaterials. A great effort has been made in recent years to obtain h-BNNS with a high-yield process to enable its large-scale application in industrial plants. In this work, we developed a mechanochemical method for obtaining h-BN nanosheets assisted by NaOH aqueous solution as process aid and aimed the ideal balance between yield, quality and process sustainability. Images obtained by transmission electron microscope suggested a great exfoliation of the h-BNNS in the range of 12–38 layers observed for well dispersed nanosheets. The macroscopic stability study, the polydispersity index, hydrodynamic diameter, and Zeta potential measurements suggested that material prepared in autoclave and ball milling followed by tip sonication process at 40 °C (h-BNNS-T40) could be considered the most promising material. The process used in this case reached a yield of about 37% of nanosheets with an optimal balance between quality and practicality. A hybrid lamellar material was also prepared by drop-casting and dip-coating techniques. An increase on thermal stability in oxidizing atmosphere was observed with respect to the pure graphene oxide (GO). Fourier transformation infrared spectroscopy and RAMAN suggested the presence of chemical interactions between h-BNNS and GO in the hybrid. This fact supports the interest of extending the study of this hybrid (which has an easy preparation method) to further explore its applicability.

Effects of Tungsten Disulphide Coating on Tapered Microfiber for Relative Humidity Sensing Applications.

Tungsten disulphide (WS2) is a two-dimensional transition-metal dichalcogenide material that can be used to improve the sensitivity of a variety of sensing applications. This study investigated the effect of WS2 coating on tapered region microfiber (MF) for relative humidity (RH) sensing applications. The flame brushing technique was used to taper the standard single-mode fiber (SMF) into three different waist diameter sizes of MF 2, 5, and 10 µm, respectively. The MFs were then coated with WS2 via a facile deposition method called the drop-casting technique. Since the MF had a strong evanescent field that allowed fast near-field interaction between the guided light and the environment, depositing WS2 onto the tapered region produced high humidity sensor sensitivity. The experiments were repeated three times to measure the average transmitted power, presenting repeatability and sensing stability. Each MF sample size was tested with varying humidity levels. Furthermore, the coated and non-coated MF performances were compared in the RH range of 45–90% RH at room temperature. It was found that the WS2 coating on 2 µm MF had a high sensitivity of 0.0861 dB/% RH with linearity over 99%. Thus, MF coated with WS2 encourages enhancement in the evanescent field effect in optical fiber humidity sensor applications.

Structured Thin Films Based on Synergistic Effects of MnTa2O6 Oxide and bis-Carboxy-phenyl-substituted Porphyrins, Capable to Inhibit Steel Corrosion

Covering steel surfaces with suitable materials with the capacity to protect against corrosion represents a challenge for both research and industry, as steel, due to its paramount utility, is the most recycled material. This study presents the realization of new sandwich type materials based on 5,10-(4-carboxy-phenyl)-15,20-(4-phenoxy-phenyl)-porphyrin or 5,15-(4-carboxy-phenyl)-10,20-diphenylporphyrin and MnTa2O6 designed to improve corrosion inhibition of steel in aggressive media. The thin films, designed as single- or sandwich-type structures were obtained on carbon steel through the drop-casting technique. Morphological investigations of thin films were carried out by field emission-scanning electron microscopy (SEM) and atomic force microscopy (AFM). The inhibition of a steel corrosion process was evaluated in an aggressive environment of 0.1 M HCl by performing electrochemical investigations such as open circuit potential (OCP) and the potentiodynamic polarization technique. The influence of variations in the cathodic Tafel slopes βc and anodic Tafel slopes βa over the corrosion rates was discussed. The best corrosion inhibition efficiency of 91.76% was realized by the steel electrode covered with sandwich-type layers of 5,15-(4-carboxy-phenyl)-10,20-diphenylporphyrin on the bottom layer and MnTa2O6 on the top. The effect of location of the COOH groups in the cis or trans position on the tetrapyrrolic ring was also discussed to understand the corrosion inhibition mechanism.

Far Infrared Laser Detector Based on Multi-Walled Carbon Nanotubes and Blend of (Polyaniline - Polymethyl Methacrylate) Polymers with Methyl Blue Dye for Photoconductive Applications

Infrared photoconductive detectors working in the far-infrared region and room temperature were fabricated. The detectors were fabricated using three types of carbon nanotubes (CNTs); MWCNTs, COOH-MWCNTs, and short-MWCNTs. The carbon nontubes suspension is deposited by dip coating and drop–casting techniques to prepare thin films of CNTs. These films were deposited on porous silicon (PSi) substrates of n-type Si. The I-V characteristics and the figures of merit of the fabricated detectors were measured at a forward bias voltage of 3 and 5 volts as well as at dark and under illumination by IR radiation from a CO2 laser of 10.6 μm wavelengths and power of 2.2 W. The responsivity and figures of merit of the photoconductive detector are improved by coating the MWCNTs films with a thin layer of a blend (polyaniline - polymethyl methacrylate) polymer with methylene blue dye. The coated MWCNTs films showed better performances, so this type of coating can be considered as a surface treatment of the detector film, which highly increased the responsivity and specific detectivity of the fabricated IR laser detector-based MWCNTs. The photocurrent response for the coated films was increased about 25 times than that for uncoated films. The results proved the role of the polymer in the enhancement of the performance of the IR photoconductive detectors. Keywords: Carbon nanotubes, Infrared detector, Polyaniline polymer, Polymethyl methacrylate polymer, Methyl Blue dye.

Enhanced Propanol Response Behavior of ZnFe2O4 NP-Based Active Sensing Layer Induced by Film Thickness Optimization

Development of gas sensors displaying improved sensing characteristics including sensitivity, selectivity, and stability is now possible owing to tunable surface chemistry of the sensitive layers as well as favorable transport properties. Herein, zinc ferrite (ZnFe2O4) nanoparticles (NPs) were produced using a microwave-assisted hydrothermal method. ZnFe2O4 NP sensing layer films with different thicknesses deposited on interdigitated alumina substrates were fabricated at volumes of 1.0, 1.5, 2.0, and 2.5 µL using a simple and inexpensive drop-casting technique. Successful deposition of ZnFe2O4 NP-based active sensing layer films onto alumina substrates was confirmed by X-ray diffraction and atomic force microscope analysis. Top view and cross-section observations from the scanning electron microscope revealed inter-agglomerate pores within the sensing layers. The ZnFe2O4 NP sensing layer produced at a volume of 2 μL exhibited a high response of 33 towards 40 ppm of propanol, as well as rapid response and recovery times of 11 and 59 s, respectively, at an operating temperature of 120 °C. Furthermore, all sensors demonstrated a good response towards propanol and the highest response against ethanol, methanol, carbon dioxide, carbon monoxide, and methane. The results indicate that the developed fabrication strategy is an inexpensive way to enhance sensing response without sacrificing other sensing characteristics. The produced ZnFe2O4 NP-based active sensing layers can be used for the detection of volatile organic compounds in alcoholic beverages for quality check in the food sector.

Evaluation of the Thermal and Morphological Properties of γ-Irradiated Chitosan-Glycerol-Based Polymeric Films

Industry-sponsored research has intensified to find suitable substitutes for synthetic polymers. For this purpose, biopolymers are promising materials that are extracted from renewable resources. However, there are areas of concern (biopolymers are mostly brittle in the dry state) that require further research before they are used in advanced applications. To overcome this, plasticizers are often added to biopolymers to enhance their physicochemical properties. In this study, chitosan (CH)-glycerol (GL)-based polymeric films were prepared by a simple drop-casting technique, and the influence of a plasticizer (GL) on the properties of chitosan films was analyzed. Additionally, the as-prepared samples were irradiated with γ-rays (60Co γ rays with a dose of 102 kGy) to study the effect of γ-irradiation on the properties of polymeric composites. To achieve this, different samples were prepared by varying the amount of GL. FT-IR analysis revealed the interruption of hydrogen bonding in chitosan by the incorporation of GL. This led to the chain-spreading of CH, which ultimately increased the flexibility of the composite films (CH-GL). The DSC of the CH film showed two peaks: one endothermic peak below 100 °C (due to water vapor) and a second exothermic peak that appeared between 130 and 360 °C (degradation of the amino group). Plasticization of CH films with GL was confirmed by DSC, where the exothermic degradation was converted into an endothermic peak. Depending upon the amount of GL, γ-irradiation considerably affected the chemical structure of CH by breaking the carbohydrate and pyranose rings; this led to a decrease in the crystallinity of the composite films. The changes studied in the DSC and TGA analysis complemented each other. γ-irradiation also affected the morphology of the films, which changed from smooth and homogeneous to roasted structures, with random swelling on the surface of the films. This swelling reflected the degradation of the surfaces into thin layers. Considering the changes that occurred in the films post-γ-irradiation, it can be inferred that the irradiation dose of 102 kGy is sufficient to degrade as-prepared biopolymer composites.

Nafion Protective Membrane Enables Using Ruthenium Oxide Electrodes for pH Measurement in Milk

The application of conventional glass electrodes for pH measurement in food samples has a serious drawback: glass is fragile and should be handled with care in order to prevent breaking and thus contaminating the food with dangerous shattered fragments. The implementation of all-solid-state sensors allows for pH measurements without this contamination risk but their application in food samples is scarce due to their inability to be used in complex food matrices that contain fats, proteins, yeasts, etc. We can solve this problem by coating solid-state RuO2 electrodes with a semi-permeable protective NafionTM membrane layer. We show that covering screen printed potentiometric RuO2 electrodes with Nafion membrane using a drop-casting technique does not alter the performance of the electrodes in milk samples and provides similar results to the conventional glass electrode. Furthermore, we discovered that thermal treatment of Nafion-layers at 80 °C for 2 h after each layer deposition optimises the performance of the electrodes, makes them usable even in heated aqueous solutions, and increases their lifetime.

Morphological and electrochemical characterizations of a carbon nitride/highly oriented pyrolytic graphite electrode

• The size distribution of g-C 3 N 4 exfoliated particles in suspension was studied. • The morphology, texture, thickness and covered area of the film were analyzed. • Different microscopy techniques were employed in the surface studies. • Electrochemical characterization of the surface were performed. • For HPRR, TOF parameter of electroactive sites on HOPG/ g-C 3 N 4 was estimated. In the present work, we present a complete study about morphology and electrochemical properties of graphite carbon nitride (g-C 3 N 4 )/highly oriented pyrolytic graphite (HOPG) electrode surface for hydrogen peroxide reduction reaction (HPRR). First, the size distribution of exfoliated g-C 3 N 4 particles in suspension was studied. By drop-casting technique, the film on the HOPG surface was deposited and the size distribution of conglomerates on the surface was studied. Different microscopy and image processing techniques were combined to analyse the surface landscape. Properties like morphology, texture, thickness, local composition and covered area by the discontinuous film were also analysed. By electrochemical techniques surface properties like wetting area and roughness factor were determined. For HPRR the electroactive area, number and types of active sites and their rotation frequency were studied. These studies suggest that g-C 3 N 4 is a useful electroactive material for HPRR, which can be used to enhance the electro-activity of other cheaper carbonaceous substrates.

Enhancement of Photoconductive Detector Based on Carbon Nanotubes Decorated with Silver Nanoparticles by Adding Conductive Polymer

In this work, wide band range photo detector operating in UV, Visible and IR was fabricated using carbon nanotubes (MWCNTs, SWCNTs) decorated with silver nanoparticles (Ag NPs). Silicon was used as a substrate to deposited CNTs/Ag NPs by the drop casting technique. Polyamide nylon polymer was used to coat CNTs/Ag NPs to enhance the photo-response of the detector. The electro-exploding wire technology was used to synthesize Ag NPs. Good dispersion of silver NPs achieved by a simple chemistry process on the surface of CNTs. The optical, structure and electrical characteristic of CNTs decorated with Ag NPs were characterized by X-Ray diffraction and Field Emission Scanning Electron Microscopy. X-ray diffraction patterns of Ag NPs exhibited 2θ values (38.1°,44.3°) corresponding to the Ag nanocrystal, while the XRD pattern of MWCNTs and SWCNTs /Ag NPs peaks appeared at 2θ = 26.2° corresponding to the (002) and at 2theta=44° which corresponds with miller indices (100) for CNTs and (200) for Ag NPs. The optical properties measured by UV-Vis. Spectroscopy. Broad and strong surface plasmon resonance (SPR) peak was detected at 420 nm, for Ag NPs. The absorption of CNTs/Ag NPs increased significantly from UV to near IR region (300-1000 nm). Ag NPs decorated CNTs without any impurities, according to field mission scanning electron microscopy examination, with typical particle sizes of (50-80nm) for Ag-NPs, 44nm for MWCNTs/Ag-NPs, and 30nm for SWCNTs/Ag NPs. ֹThe I-V characteristics at forward bias voltage (0.5-10) volt were studied. The figure of merits (responsivity, photocurrent gain, NEP and detectivity) after coating with polymer of the detector were measured in the dark and after illumination with UV LED (365 nm), Tungsten lamp (500-800 nm) and Laser diode (808 nm).

Induced Birefringence by Drop Cast in EFBG Ammonia Sensors

In this paper, an induced birefringence was observed on an ammonia sensor based on an etched fiber Bragg grating (EFBG) coated with an organic film. The film was prepared with a solution of the perylene derivative, along with the copolymer PCDTBT in chlorobenzene. The EFBG was coated by drop cast technique, and a split in the reflection band, characteristic of birefringence, was observed after deposition. The response of the two observed peaks as a function of time was modeled by a pair of exponentials that could represent two processes: adsorption followed by diffusion of the gas molecules in the microstructured film. Such phenomena alter the boundary conditions of the optical fiber propagating mode, which allows an indirect ammonia detection by monitoring the EFBG wavelength shift of the reflected peaks. The sensor was experimentally tested in a concentration range from 3 ppm to 41,700 ppm, and the calibrations curves were determined in a range from 27 ppm to 6960 ppm. The two observed peaks showed different sensitivities, which presents an intrinsic potential for multiparameter measurements. The split in the reflection band was hypothesized to be birefringence induced by the formation of an asymmetric film. This hypothesis was numerically evaluated and compared with the experimental results.

Extensive study of optical contrast between bulk and nanoscale transition metal dichalcogenide semiconductors

A remarkable refinement in the optical behavior of two-dimensional transition metal dichalcogenides (TMDs) has been brought to light when cleaved from their respective bulks. These atomically thin direct bandgap semiconductors are highly responsive to optical energy which proposes the route for futuristic photonic devices. In this manuscript, we have substantially focused on the optical study of MoS2 and WS2 nanosheets and comparative analysis with their bulk counterparts. The synthesis of nanosheets has been accomplished with liquid exfoliation followed by fabrication of thin films with drop-casting technique. X-ray diffraction and field emission scanning electron microscopy affirmed the morphology, whereas, UV–visible spectroscopy served as the primary tool for optical analysis. It was observed that several parameters, like optical conductivity, optical band-gap energy etc. have enhanced statistics in the case of exfoliated nanosheets as compared to their respective bulks. Some researchers have touched upon this analysis for MoS2, but it is completely novel for WS2. We expect our work to clearly distinguish between the optical behaviors of nanoscale and bulk TMDs so as to intensify and strengthen the research related to 2D-layered materials for optoelectronic and photovoltaic applications.

Ammonia Gas Sensing Characteristic of P3HT-rGO-MWCNT Composite Films

In this work, the P3HT:rGO:MWCNTs (PGC) nanocomposite film applied to the ammonia gas sensor was successfully fabricated by a drop-casting technique. The results demonstrated that the optimum weight ratio of the PGC nanocomposite gas sensor is 20%:60%:20% as the weight ratio of P3HT:rGO:MWCNTs (called PGC-60). This weight ratio leads to the formation of nanostructured composites, causing the efficient adsorption/desorption of ammonia gas in/out of the film surface. The sensor based on PGC-60 possessed a response time of 30 s, sensitivity up to 3.6% at ammonia gas concentration of 10 ppm, and relative sensitivity of 0.031%/ppm. These results could be attributed to excellent electron transportation of rGO, the main adsorption activator to NH3 gas of P3HT, and holes move from P3HT to the cathodes, which works as charge “nano-bridges” carriers of Multi-Walled Carbon Nanotubes (MWCNTs). In general, these three components of PGC sensors have significantly contributed to the improvement of both the sensitivity and response time in the NH3 gas sensor.

Polyvinyl alcohol coating microbottle resonator on whispering gallery modes for ethanol liquid sensor

This experimental paper study on the effect of polyvinyl alcohol (PVA) coating on whispering gallery modes on microbottle resonator (MBR) as liquid ethanol sensor. The silica fiber SMF-28 is used to create microbottle resonator using a technique known as “soften-and-compress” and formed in three sizes with bottle length Lb, stem diameter of Ds and bottle diameter of Db. The MBR then coated with PVA using a drop-casting technique with the coating diameter <10μm for all. The MBR-PVAs characterized with microfiber of 2μm and managed to have >104 for Q-factor for all condition with MBR-PVA-C is the highest, 2.783 × 104. The ethanol liquid with concentrations ranging from 10% to 100 %ppm is used for sensing purposes. Sensitivity, linearity, repeatability and stability performance by MBR-PVAs then compared between transmitted spectral and wavelength shift analysis. The MBR-PVA-C defined to have the best performance for all than another size of MBR-PVAs. Transmitted spectral analysis showed the sensitivity is 0.2699 dB/%ppm with 99.2% of linearity, and wavelength shift analysis showed the sensitivity is 0.2 pm/%ppm with a linearity of 98.01% respectability. Hence, MBR-PVAs experienced three cycles of repeatability and a 60-second stability procedure for performance optimization.

Prevention the formation of biofilm on orthopedic implants by melittin thin layer on chitosan/bioactive glass/vancomycin coatings

Methicillin-resistant and Vancomycin-resistant Staphylococcus aureus bacteria (MRSA and VRSA, respectively) can seriously jeopardizes bone implants. This research aimed to examine the potential synergistic effects of Melittin and vancomycin in preventing MRSA and VRSA associated bone implant infections. Chitosan/bioactive glass nanoparticles/vancomycin composites were coated on hydrothermally etched titanium substrates by casting method. The composite coatings were coated by Melittin through drop casting technique. Melittin raised the proliferation of MC3T3 cells, making it an appropriate option as osteoinductive and antibacterial substance in coatings of orthopedic implants. Composite coatings having combined vancomycin and Melittin eliminated both planktonic and adherent MRSA and VRSA bacteria, whereas coatings containing one of them failed to kill the whole VRSA bacteria. Therefore, chitosan/bioactive glass/vancomycin/Melittin coating can be used as a bone implant coating because of its anti-infective properties.

Mode-locked thulium/holmium-doped fiber laser with vanadium carbide deposited on tapered fiber

Vanadium carbide (V2C), a member of the MXene family, promises numerous possibilities in ultrafast laser technology with substantial applications in various optical industries. In this work, MXene V2C was deposited onto a tapered fiber using the drop-casting technique and incorporated into a thulium/holmium doped fiber laser cavity for generating mode-locked outputs in the 2.0 µm region. The fabricated SA exhibited nonlinear optical properties such as saturation intensity and modulation depth of 2.07 MW/cm2 and 7.57%, respectively. The findings of the mode-locked characteristics showed a central wavelength of 1937 nm with a signal-to-noise ratio (SNR) of 73 dB. Correspondingly, the laser-generated mode-locked pulses with output power, pulse energy, and peak power of 2.71 mW, 235.2 pJ, and 0.14 kW, respectively. The results suggest that the mode-locked laser obtained based on the MXene V2C could be applied to the field of photonics.

Identification of Recycled Cooking Oil by Varying Number of Au/GO Coated Fiber Optic’s Loop Ring

This study investigates the effect gold nanoparticles (Au)/graphene oxide (GO) coated fibre optics with various number of loop ring in identifying recycled cooking oil based on their frying time. Various layers of gold nanoparticles (AuNP) suspension were deposited onto the substrate via drop casting technique. Few material characterizations were performed such as Fourier Transform Infrared (FTIR) spectroscopy, Ultraviolet Visible (UV-Vis) spectroscopy and refractometer analysis. Three macrobending structures of Au/GO coated fiber optic’s loop ring such as single, double and triple loops with diameter of 1.5cm were formed to generate large area of evanescent field around the fibre and to excite surface plasmon polaritons due to the interaction between AuNPs and analytes. Cooking oil samples with different frying time such as 14 minutes, 28 minutes and 42 minutes were prepared as analytes. The FTIR analysis revealed some changes in the transmittance percent of some bands as well as some slight shifts in the exact position of the bands due to the different of fatty acid composition. As the Au/GO coated fibre optics were immersed into the samples, the penetration depths were obtained as 142.75nm and 168.91nm at operating wavelengths of λ=1310nm and λ=1550nm, respectively. By using 1550nm operating wavelength due to its greater penetration depth than 1310nm, triple loop rings fibre optics coated with two layers of AuNP and one layer of GO exhibits a linear consistency with maximum sensitivity up to 69.17% due to the formation of large evanescent field around the loop area and intense SPP excitation.

Solvent Effect to the Uniformity of Surfactant-Free Salmon-DNA Thin Films.

Fabrication of surfactant-modified DNA thin films with high uniformity, specifically DNA–CTMA, has been well considered via drop-casting and spin-coating techniques. However, the fabrication of thin films with pure DNA has not been sufficiently studied. We characterize the uniformity of thin films from aqueous salmon DNA solutions mixed with ethanol, methanol, isopropanol, and acetone. Measurements of thickness and macroscopic uniformity are made via a focused-beam ellipsometer. We discuss important parameters for optimum uniformity and note what the effects of solvent modifications are. We find that methanol- and ethanol-added solutions provide optimal fabrication methods, which more consistently produce high degrees of uniformity with film thickness ranging from 20 to 200 nm adjusted by DNA concentration and the physical parameters of spin-coating methods.

Effect of HDI-Modified GO on the Thermoelectric Performance of Poly(3,4-ethylenedioxythiophene):Poly(Styrenesulfonate) Nanocomposite Films.

Composite films based on conducting polymers and carbon nanomaterials have attracted much attention for applications in various devices, such as chemical sensors, light-emitting diodes (LEDs), organic solar cells (OSCs), among others. Graphene oxide (GO) is an ideal filler for polymeric matrices due to its unique properties. However, GO needs to be functionalized to improve its solubility in common solvents and enable the processing by low-cost solution deposition methods. In this work, hexamethylene diisocyanate (HDI)-modified GO and its nanocomposites with poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) were developed, and their morphology, thermal, electrical, thermoelectrical and mechanical performance were characterized. The influence of the HDI functionalization degree and concentration on the nanocomposite properties were assessed. The HDI-GO increased the crystallinity, lamella stacking and interchain coupling of PEDOT:PSS chains. A strong improvement in electrical conductivity, thermal stability, Young’s modulus and tensile strength was found, showing an optimum combination at 2 wt% loading. Drop and spin casting techniques were applied onto different substrates, and the results from deposition tests were analyzed by atomic force microscopy (AFM) and UV–vis spectroscopy. A number of parameters influencing the depositions process, namely solvent nature, sonication conditions and ozone plasma treatment, have been explored. This study paves the way for further research on conducting polymer/modified GO nanocomposites to optimize their composition and properties (i.e., transparency) for use in devices such as OSCs.