Fiber Dimensions Research Articles

Lignocellulosic-Based/High Density Polyethylene Composites: A Comprehensive Study on Fiber Characteristics and Performance Evaluation

Lignocellulosic-based polymer composites have gained significant interest due to their ‘’green’’ character as a response to environmental concerns. A diverse array of lignocellulosic fibers is utilized, depending on fiber dimensions, chemical composition, moisture content, and the fiber–matrix interface. The aim of this study is to establish an alternative standardized methodology, aimed at comparatively estimating the performance of polymer composites through the examination of individual plant fibers. The fibers studied are ramie, hemp, flax, and kenaf, and HDPE-based corresponding composites were analyzed for their performance across various fiber-content levels (10, 20, and 30 wt.%). It was found that kenaf showcases the largest average fiber diameter, succeeded by hemp, ramie, and flax. Additionally, ramie and kenaf exhibit elevated levels of crystallinity, suggesting increased cellulose content, with kenaf having the lowest crystallinity index among the fibers compared. Based on Thermogravimetric analysis, ramie displays the lowest moisture content among the examined fibers, followed by hemp, flax, and ultimately kenaf, which is recorded to have the highest moisture content, while, similarly, ramie exhibits the lowest mass loss at the processing temperature of the corresponding composites. Composites containing fibers with smaller diameters and higher crystallinity indexes and lower moisture absorptions, such as ramie and hemp, demonstrate superior thermal stability and exhibit increased Young’s modulus values in their respective composites. However, poor interfacial adhesion affects mechanical performance across all composites. Understanding fiber morphology, inner structure, and thermal stability is important for developing new composite materials and optimizing their selection for various applications.

Mechanical recycling of biobased polyethylene-agave fiber composites

Biobased polymers have emerged as a promising alternative to petroleum-based polymers in terms of lower environmental impact. However, to improve their carbon footprint, it is important to study strategies, such as recycling, extending the useful life of these biopolymers, and mitigate their higher costs compared to petroleum-based polymers. Adding agro-industrial wastes as fillers or reinforcements is another option to reduce the cost and increase the biobased content to produce composites. This study aimed to evaluate the addition of agave fibers to biobased linear low-density polyethylene (bio-LLDPE) and their effect on its reprocessing by extrusion, i.e., close-loop mechanical recycling. The results revealed that it was possible to reprocess the bio-LLDPE alone as limited changes in their physical properties were observed up to 34 cycles. However, for the composites, the viscosity changed in the first eight cycles mainly due to fiber break-up (lower aspect ratio). The dimensions of the agave fibers are modified by reprocessing. In the initial 8 cycles, there is a notable decrease in fiber dimensions, affecting the tensile, flexural, and impact properties of the composites. The water uptake was found to decrease with each cycle due to better fiber dispersion and the reduction of interfacial voids/defects. Nevertheless, the color of the bio-LLDPE and its composites showed significant changes by reprocessing, which is associated with thermal and oxidation degradation. Despite minor property losses, the study reveals that bio-LLDPE/agave fiber composites exhibit a commendable level of sustainability. This characteristic enables their extended reuse and reprocessing over a prolonged duration.

Influence of cladding tube structure on transmission characteristics of negative curvature terahertz fiber

A novel type of polarization negative curvature terahertz fiber has been designed, which has a cladding region composed of two long semi-circular cladding tubes in the horizontal direction and four long semi-elliptical cladding tubes in the oblique direction. The optimal fiber dimensions are determined to investigate the internal relationship between polarization characteristics and fiber cladding structure. The transmission performances of the negative curvature fiber are investigated by varying the thickness of fiber cladding tubes and adjusting the structural characteristics of cladding tubes in different directions. Relatively good transmission performances can be obtained with a cladding tube thickness of 80 μm. The birefringence can be stably maintained at the order of 10−4, and the confinement loss of the x-polarized mode at 2.55 THz is 0.036 dB cm−1. Moreover, the dispersion coefficient of the two polarized modes is stable between ±0.6 ps (THz·cm)−1 in the 2.3–2.6 THz band. The bent performance of the designed fiber at 2.52 THz is also discussed. The results show that the fiber has low bending sensitivity, and can still maintain excellent birefringence and low confinement loss in the bending state. For the y polarization, the birefringence can be basically stabilized at the order of 10−4 within a bending radius of 10–60 cm.

Parametric study for optimizing fiber‐reinforced concrete properties

AbstractConcrete with fiber reinforcement is stronger and more ductile than concrete without reinforcement. Significant efforts have been made to demonstrate the properties and enhancements of concrete after reinforcement with various types and shapes of fibers. However, the issue of optimization in the reinforcement process is still unanswered. There is no academic study in the literature now available that can pinpoint the ideal fiber type, quantity, and shape and, more crucially, the overall technical viability of the reinforcement. The parametric analysis in this study determines the ideal shape, size, and proportion of fibers. The input and output parameters were separated from the optimization design variables. Input parameters included assessment of samples of fresh and mechanical concrete properties and the influence of type, length, and percentage of fiber on concrete performance. The aim was to establish the most efficient relationship between fiber dose and dimension to optimize the combined responses of workability and splitting tensile, flexural, and compressive strength. The mechanical and fresh properties of concrete reinforced with four different fibers, PFRC‐1, PFRC‐2, SFRC‐1, and SFRC‐2, were tested. The analysis showed that SFRC‐2‐20 mm‐1%, with compressive, split tensile, flexural, and workability values of 44.7 MPa, 3.64 MPa, 5.3 MPa, and 6.5 cm respectively, was the most effective combination among the materials investigated. The optimization technique employed in this study offers new, important insights into how input and output parameters relate to one another.

Direct electrospinning of short polymer fibers: factors affecting size and quality

The growing demand for lightweight and robust materials drives the development of polymer-based and fiber-reinforced composites. Here, using short fibers offers several advantages; however, currently employed methods for producing short fibers, such as homogenization, result in a wide dispersion of dimensions in the produced fibers, which is an undesirable effect in composite materials. In this study, electrospinning is used to produce polymer short fibers directly. This research highlights, for the first time, the differences in the electrospinning process dynamics between short and continuous fibers. By adjusting parameters: voltage and distance, we control dimensions of short fibers below 1 µm in diameter and around 4 µm in length to a few microns in diameter and approximately 14 µm in length. Direct electrospinning of short fibers offers significant advantages, including a narrow size distribution and reproducibility compared to chopped continuous fibers with homogenization.

Socioemotional Wealth and Family Firm Performance: The Moderating Role of CEO Tenure and Millennial CEO

AbstractThis study sheds light on how socioemotional wealth (SEW) theory functions in family firms. Focusing on the impact of the most highly appraised FIBER dimensions on the performance of such firms, we contextualize SEW by discussing the heterogeneity among family principals via the under‐researched role played by specific characteristics of family CEOs. Integrating arguments from SEW and generational theory, we test our theoretical hypotheses using global survey data from a sample of 1833 family firms from 33 countries. The main findings suggest that while family control and influence is not associated with performance, family members’ identification with the firm (FI) improves performance. Moreover, the positive impact of FI on family firm performance weakens in family firms with long‐tenured family CEOs. Finally, in family firms led by Millennial CEOs, the positive impact of FI on family firm performance is stronger. Our findings enrich both the theoretical insights into and practical comprehension of SEW priorities in relation to family firm performance, thereby underscoring the diverse performance outcomes associated with various types of family CEOs.

Muscle fibre size and myonuclear positioning in trained and aged humans.

Changes in myonuclear architecture and positioning are associated with exercise adaptations and ageing. However, data on the positioning and number of myonuclei following exercise are inconsistent. Additionally, whether myonuclear domains (MNDs; i.e., the theoretical volume of cytoplasm within which a myonucleus is responsible for transcribing DNA) and myonuclear positioning are altered with age remains unclear. The aim of this investigation was to investigate relationships between age and activity status and myonuclear domains and positioning. Vastus lateralis muscle biopsies from younger endurance-trained (YT) and older endurance-trained (OT) individuals were compared with age-matched untrained counterparts (YU and OU; OU samples were acquired during surgical operation). Serial, optical z-slices were acquired throughout isolated muscle fibres and analysed to give three-dimensional coordinates for myonuclei and muscle fibre dimensions. The mean cross-sectional area (CSA) of muscle fibres from OU individuals was 33%-53% smaller compared with the other groups. The number of nuclei relative to fibre CSA was 90% greater in OU compared with YU muscle fibres. Additionally, scaling of MND volume with fibre size was altered in older untrained individuals. The myonuclear arrangement, in contrast, was similar across groups. Fibre CSA and most myonuclear parameters were significantly associated with age in untrained individuals, but not in trained individuals. These data indicate that regular endurance exercise throughout the lifespan might better preserve the size of muscle fibres in older age and maintain the relationship between fibre size and MND volumes. Inactivity, however, might result in reduced muscle fibre size and altered myonuclear parameters.

Macroscopic and microscopic diagnosis of three Entandrophragma species traded in Türkiye

The anatomical characteristics are highlighted for Entandrophragma cylindricum, Entandrophragma utile, and Entandrophragma angolense. Wood samples, which were previously obtained from commercial timber industries in the Marmara region of Türkiye and used as course materials, were used. Qualitative and quantitative anatomical characteristics were determined. Qualitatively, characters such as distinct growth rings, diffuse-porous wood, deposits in vessel elements, simple perforation plates, alternate intervessel pits, heterogeneous ray type, and septate fibres, were common to all species. The quantitative evaluation showed that there were differences between species. Entandrophragma species differ in some wood characteristics such as the tangential diameter of the vessel, ray height, ray width, and fibre lumen diameter. E. utile had higher values of the mean tangential vessel diameter (180 μm) and fiber lumen diameter (18.4 μm) than the other two species. It is possible to say that the anatomical features of E. cylindricum differ from that of other species and that it will be easier to diagnose among other species. E. cylindricum had the lowest values of the mean tangential vessel diameter (147 μm) and ray height (361 μm). Distinctive characters for E. utile and E. angolense are tangential vessel diameter, vessel length, ray height, ray width, and all fibre dimensions.

Shear wave propagation in a fiber-laden viscoelastic waveguide under prestress: Inverse modeling challenges

The functional role of skeletal muscle and the hierarchal microstructure and arrangement of fibers within it results in anisotropy and inhomogeneity in both material properties and imposed stresses. Dynamic elastography reconstruction methods for estimating muscle tissue viscoelastic properties that are based on assumptions of homogeneity, isotropy and only bulk wave motion may produce inaccurate estimates. Biases may be introduced in reconstruction by homogenizing muscle with axially aligned fibers and approximating it as transversely isotropic. The significance of these biases, and their interplay with imposed stresses and confounding waveguide effects due to small cross-sectional dimensions, is quantified with a series of numerical finite element and experimental elastography studies on cylindrically-shaped fiber-laden muscle phantoms, with varying fiber dimensions. Specifically, numerical simulations of elastography are conducted on 4-, 60- and 113-fiber models with the aligned fiber cross-sectional area fixed (reduced fiber diameter as fiber count increases) and comprising approximately 40% of the cross-sectional area of the cylindrical phantom that is also undergoing tensile axial pre-loading. Fiber elastic moduli twice that of connective tissue are considered. Experimental studies of the 4-fiber model are used to validate the numerical model. [Funding support: NSF 1852691 and NIH AR071162]

Electrospinning: Processes, Structures, and Materials

Electrospinning is a simple and affordable method of producing nanofibers, offering a large specific surface area and highly porous structures with diameters ranging from nanometers to micrometers. This process relies on an electrostatic field, providing precise control over the fiber dimensions and morphologies through parameter optimization and the use of specialized spinnerets and collectors. The paper extensively covers the electrospinning process and parameters, shedding light on the factors influencing electrospinning. It addresses the morphological and structural aspects of electrospun fibers that are used in different applications. Additionally, this paper explores various polymeric and non-polymeric materials used in electrospinning. Furthermore, it investigates the incorporation of fillers during electrospinning, using an electric field to enhance properties and functionality. The review concludes by offering insights into upscaling electrospinning production.

Anatomy based papermaking potential of some woody plants under different ecological conditions

The increasing use of wood in the forest industry and reduction of forest resources have prompted the paper industry to look for new materials. To this end, this study examined the biometric coefficients of the seven woody stems grown in different regions and investigated suitability for papermaking as an alternative to the use of wood. Wood samples of each species were collected from two different regions in Türkiye: the Kozan region, which has a Mediterranean climate, and the Yuvacık region, which has a mostly oceanic climate. The species included in the study were Phillyrea latifolia (mock privet), Arbutus andrachne (greek strawberry tree), Erica arborea (tree heath), Spartium junceum (spanish broom), Laurus nobilis (bay tree), Pistacia turpentine (cyprus turpentine tree), and Rhus coriaria (elm-leaved sumac). All fibers were classified as short. The longest fiber was observed for Spartium junceum (spanish broom) in Kozan. The fiber diameter was highest for Arbutus andrachne (greek strawberry tree) from Kozan, followed by Rhus coriaria (elm-leaved sumac) from Yuvacık and Laurus nobilis (bay tree) from Kozan. The fiber dimensions and the relationship between them were statistically analyzed. These included the slenderness ratio, flexibility coefficient, Runkel ratio, rigidity coefficient, Luce’s shape factor, F-factor, and Muhlsteph ratio. Although differences in fiber properties were detected between the two regions, it was determined that these were not enough to affect the desired properties for paper production. It was concluded that the fibers could be used in pulp, paperboard, and corrugated board production when mixed with long fibers.

The effect of nitrogen source and levels on hybrid aspen tree physiology and wood formation.

Nitrogen can be taken up by trees in the form of nitrate, ammonium and amino acids, but the influence of the different forms on tree growth and development is poorly understood in angiosperm species like Populus. We studied the effects of both organic and inorganic forms of nitrogen on growth and wood formation of hybrid aspen trees in experimental conditions that allowed growth under four distinct steady-state nitrogen levels. Increased nitrogen availability had a positive influence on biomass accumulation and the radial dimensions of both xylem vessels and fibers, and a negative influence on wood density. An optimal level of nitrogen availability was identified where increases in biomass accumulation outweighed decreases in wood density. None of these responses depended on the source of nitrogen except for shoot biomass accumulation, which was stimulated more by treatments complemented with nitrate than by ammonium alone or the organic source arginine. The most striking difference between the nitrogen sources was the effect on lignin composition, whereby the abundance of H-type lignin increased only in the presence of nitrate. The differential effect of nitrate is possibly related to the well-known role of nitrate as a signaling compound. RNA-sequencing revealed that while the lignin-biosynthetic genes did not significantly (FDR <0.01) respond to added NO3 - , the expression of several laccases, catalysing lignin polymerization, was dependent on N-availability. These results reveal a unique role of nitrate in wood formation and contribute to the knowledge basis for decision-making in utilizing hybrid aspen as a bioresource.

Nano- and Microstructures of Collagen-Nanocellulose Hydrogels as Engineered Extracellular Matrices.

The extracellular matrix (ECM) is the fundamental acellular element of human tissues, providing their mechanical structure while delivering biomechanical and biochemical signals to cells. Three-dimensional (3D) tissue models commonly use hydrogels to recreate the ECM in vitro and support the growth of cells as organoids and spheroids. Collagen-nanocellulose (COL-NC) hydrogels rely on the blending of both polymers to design matrices with tailorable physical properties. Despite the promising application of these biomaterials in 3D tissue models, the architecture and network organization of COL-NC remain unclear. Here, we investigate the structural effects of incorporating NC fibers into COL hydrogels by small-angle neutron scattering (SANS) and ultra-SANS (USANS). The critical hierarchical structure parameters of fiber dimensions, interfiber distance, and coassembled open structures of NC and COL in the absence and presence of cells were determined. We found that NC expanded and increased the homogeneity in the COL network without affecting the inherent fiber properties of both polymers. Cells cultured as spheroids in COL-NC remodeled the hydrogel network without a significant impact on its architecture. Our study reveals the polymer organization of COL-NC hydrogels and demonstrates SANS and USANS as exceptional techniques to reveal nano- and micron-scale details on polymer organization, which leads to a better understanding of the structural properties of hydrogels to engineer novel ECMs.

Chemical properties, crystallinity, and fiber biometry of Jabon (Anthocephalus cadamba) wood for pulp raw material: the effect of age and position

Abstract Jabon (Anthocephalus cadamba) is a promising plant species with straight, visually pleasing trunks that can be harvested at a young age as a resource for pulp and paper production due to the rapid growth rate possessed. Therefore, this study aims to investigate the chemical composition and fiber biometry of 3, 6, and 9-year-old Jabon wood, determining their suitability as a pulp and paper raw material. Samples were collected from both stem and branch sections and analyzed according to the Tappi standard. Fiber cell maceration was conducted to enable the precise measurement of fiber dimensions and derivatives. The results showed high cellulose, holocellulose, and lignin content in Jabon wood, with low to moderate levels of extractives and ash. Additionally, the crystallinity index (CrI) increased with age, particularly from 3 to 9 years old. The branch of the plant, with Grade II fiber derivative quality, had lower CrI compared to the stem, while the inner stem showed a lesser value than the outer part. In conclusion, 3-year-old Jabon wood is a potential raw material for pulp and paper production.

Intraspecific Variability of Fibre Dimensions and Tissue Proportion in Medium Density Hardwoods: An Analysis

Intraspecific Variability of Fibre Dimensions and Tissue Proportion in Medium Density Hardwoods: An Analysis

Potential of natural fiber based on plant characteristics

Natural fiber is one of the prospective non-timber forest products that contribute to the augmentation of a nation’s foreign exchange within the forestry industry. The objective of this research is to ascertain the distinguishing features of several species of plants that produce natural fiber, and to evaluate the prospective applications of these fibers. The study approach commences by conducting tests on the physical qualities, followed by analysing the chemical components with the established TAPPI method. Additionally, tests are conducted to assess dimensional analyses and fiber variants. The result indicated that the examination of the physical characteristics of the specimens, namely their specific gravity and water content, yielded a strong classification falling within the range of II-IV. The study of chemical constituents, including extractives, lignin, and cellulose, across all samples yielded a range of 1.27% to 7.64%, 15.88% to 36.55%, and 24.63% to 68.32%, respectively. Similarly, the findings from the analysis of fiber dimension measurements indicate that the fiber length category ranges from fairly short to very long.

Fiber Stiffness: An Essential Parameter of the Effectiveness of Fiber-Based Lost Circulation Materials—A CFD-DEM Numerical Investigation

Summary Fiber materials have become an attractive choice for lost circulation material (LCM) applications recently. While there has been significant attention on the size, aspect ratio, and size distribution of fibers, the stiffness or basically the effect of their deformability on the sealing capability has not been studied rigorously. Experimental evaluations of fibers with different material properties could be a cumbersome, time-consuming, and expensive process. Most laboratory studies are limited to one or just a few different types of materials. Hence, a novel two-way-coupled computational fluid dynamics and discrete element method (CFD-DEM)-based numerical model is used to overcome this limitation and to simulate motion, collision, deformation, and finally entanglement of individual LCM fibers moving with the fluid along a fracture. Fiber stiffness is determined by the Young’s modulus, the fiber diameter, and the fiber length. Therefore, we investigate this effect in a parametric study with a focus on the impact of the length, diameter, and Young’s modulus of the fiber on their sealing capability. An in-depth analysis reveals that the bridging mechanism for fiber LCM changes with the stiffness of the fiber. Two distinct bridging mechanisms dependent on the fiber stiffness for fiber LCMs are identified. Based on the simulation results, we developed a conceptual model for the different mechanisms that fibers use for bridge initiation. It is also observed that in determining LCM effectiveness, both the fiber stiffness and the fiber dimensions go hand in hand. Stiff fibers were associated with greater maximum plugging pressures (MPPs). The effect of using a mix of soft and stiff fibers on fracture plugging effectiveness has been evaluated. The fiber LCM effectiveness as a consequence of the bending stiffness on bridging larger fractures is also investigated. Key Terms and Phrases lost circulation materials, fibers, fracture sealing, bridging mechanism

Wood anatomical spectrum of co-occurring species in early and late-successional tropical dry forest communities

Key messageAnalysis of wood anatomical traits revealed that drought tolerance predominates in early-successional communities, and vessel variability is relevant for species’ ecological success in seasonally dry tropical environments.Successional tropical dry forests harbor a diverse array of species subjected to a strong seasonal precipitation regime. Considering that wood encompasses diverse functional properties related to stem hydraulics and mechanical support, in this study, we asked which quantitative anatomical traits are exhibited by co-occurring species in early (EC)- and late (LC)-successional communities. We used generalized linear mixed-effects models to estimate and compare means and standard deviations of wood traits (vessel area, vessel density, vessel grouping, and fiber dimensions) between eight EC and between 13 LC co-occurring species. Wood traits were highly heterogeneous. High vessel redundancy, a property associated with water safety involved in the prevention of hydraulic failure, prevails among species coexisting in EC but is maintained through succession by the same species in LC. Highly variable fiber dimensions indicate that species coexisting in LC possess different characteristics associated with mechanical resistance. Low wood density species typical of LC, which are absent from EC, displayed wood anatomical features associated with drought-evasion mechanisms. This result implies that deforestation not only reduces taxonomic but also functional diversity. Future research should adopt a standard deviation analysis approach, as this will allow confirming the high variability in vessel diameter, even in diffuse porous species, as a key feature for the ecological success of plants facing succession-driven changes in seasonally dry environments.

Rubberwood—Potential for Pulp and Composite Board Utilization

Rubberwood (Hevea brasiliensis Muell. Arg) is underutilized in most developing countries but has potential to be a solution to the shortage of wood for pulp, paper and wood composite products at the end of its production cycle. Determining and understanding its fibre properties (fibre dimensions and morphology) is key in its utilization for pulp and paper as well as composites. This study assessed the effect of age on the fibre properties of rubberwood. Samples of wood at four ages (10, 15, 20 and 25 years) were obtained at both the axial (base and top of merchantable length) and radial direction (innerwood, middlewood and outerwood). Slivers were obtained from the samples and macerated to provide individual fibres for optical measurement. Fibre dimensions at the four ages were measured, and their morphology was determined. Fibre properties and morphology were significantly affected by age at p = 0.05. Average fibre length was 1.47 ± 0.12 mm, with non-constant variation observed across the different ages, and from pith to bark. Average lumen width was 16.87 µm, and fibre diameter ranged from 25.02 µm to 27.23 µm. The fibre properties of rubberwood potentially make it suitable for pulp and paper production as well as wood composite boards.

Natural mineral fibers: conducting inhalation toxicology studies—part B: development of a nose-only exposure system for repeat-exposure in vivo study of Libby amphibole aerosol

Background Exposure to asbestos is associated with malignant and nonmalignant respiratory disease. To strengthen the scientific basis for risk assessment on fibers, the National Institute of Environmental Health Sciences (NIEHS) has initiated a series of studies to address fundamental questions on the toxicology of naturally occurring asbestos and related mineral fibers after inhalation exposure. A prototype nose-only exposure system was previously developed and validated. The prototype system was expanded to a large-scale exposure system in this study for conducting subsequent in vivo rodent inhalation studies of Libby amphibole (LA) 2007, selected as a model fiber. Results The exposure system consisting of six exposure carousels was able to independently deliver stable LA 2007 aerosol to individual carousels at target concentrations of 0 (control group), 0.1, 0.3, 1, 3, or 10 mg/m3. A single aerosol generator was used to provide aerosol to all carousels to ensure that exposure atmospheres were chemically and physically similar, with aerosol concentration as the only major variable among the carousels. Transmission electron microscopy (TEM) coupled with energy dispersive spectrometry (EDS) and selected area electron diffraction (SAED) analysis of aerosol samples collected at the exposure ports indicated the fiber dimensions, chemical composition, and mineralogy were equivalent across exposure carousels and were comparable to the bulk LA 2007 material. Conclusion The exposure system developed is ready for use in conducting nose-only inhalation toxicity studies of LA 2007 in rats. The exposure system is anticipated to have applicability for the inhalation toxicity evaluation of other natural mineral fibers of concern.