Digital Processing Technology Research Articles

Strong and tough β-TCP/PCL composite scaffolds with gradient structure for bone tissue engineering: Development and evaluation

Bioactive ceramic bone scaffolds are limited by their brittleness. To address this limitation, we developed a new method for preparing β-tricalcium phosphate (β-TCP)/polycaprolactone (PCL) porous composite scaffolds with a gradient structure using digital light processing technology and an impregnation process. The composite scaffolds exhibited compressive strength comparable to that of pure β-TCP scaffolds but with substantially higher toughness and reliability, especially during in vitro degradation. Owing to the gradient structure, the composite scaffolds could gradually shift from high strength and stiffness to moderate strength and low stiffness, which is beneficial for bone healing and remodeling. In femoral condyle defects without mechanical stimulation, the β-TCP/PCL composite scaffolds exhibited slightly lower cellular compatibility and osteoinductive ability than those of the pure β-TCP scaffolds. However, in radial defects, composite scaffolds demonstrated a better mechanical response and bone growth capacity. The composite scaffolds maintained their structural integrity after 2–4 months, whereas the β-TCP scaffolds fractured within 2 months. This study provides a novel methodology for the development of effective scaffold fabrication strategies for load-bearing or large segmental defects with complex stress applications for use in bone healing and remodeling.

Strategies and Tools for Small- and Medium-Sized Enterprises (SMEs) to Move toward Green Operations: The Case of the Taiwan Metal Industry

Net-zero carbon reduction has become a global supply chain development trend, and the EU has established CBAM regulations. Industries that fail to effectively reduce carbon emissions will face operational challenges under these regulations. For SMEs, carbon reduction is crucial for sustainable operations. To address this challenge, governments worldwide are formulating relevant policies and investing resources to help SMEs enhance their competitiveness. In Taiwan, the metal industry has an export ratio exceeding 45%, making it a significant global production base for metal products. This study conducted a green operational transformation survey on 230 SMEs in Taiwan’s metal industry. The Taiwanese government has devised a comprehensive carbon reduction approach for the metal industry, which includes environmental facilities, digital technology introduction, process and production technology improvement, resource recycling, and energy conversion as strategies and tools for promoting carbon reduction. According to this study, the aforementioned five promotion strategies have become essential tools for SMEs in their carbon reduction efforts. This study utilized a one-way ANOVA, Pearson correlation analysis, and simple regression analysis, all of which demonstrated significant correlations among these tools. These findings can serve as a reference for other partner countries, accelerating the global industry’s transition toward green operations.

Effects of sterilization and disinfection methods on digitally designed surgical implant guide accuracy: An in vitro study.

Surgical guides are commonly used to assist with dental implant placement. This study investigated the effects of five sterilization and disinfection methods on the accuracy of implant guides. Thirty surgical guides (five in each group) were designed and printed (with digital light processing technology) using different sterilization or disinfection methods categorized into six groups: hydrogen peroxide sterilization (group one); glutaraldehyde sterilization (group two); autoclaving (group three); plasma sterilization (group four); iodophor disinfection (group five); and blank group (group six). Verification was determined using three methods: distance and angle between the cross-shaped marks, deformation after superimposing the guides, and displacement and axial changes in the virtual implant. After disinfection and sterilization, the guides in the autoclaving and iodophor groups showed a more pronounced color change and the guidein the autoclaving group had visible cracks. More significant changes were observed in the H2O2, glutaraldehyde, autoclaving, and iodophor groups regarding deformation after superimposing the guides and the distance and angle between the cross-shaped marks. The average labial deformation values (mm) of the first through fifth groups of guides were 0.283, 0.172, 0.289, 0.153, and 0.188, respectively. All groups were statistically different from the blank group for displacement and axial changes of the virtual implant (p < 0.05). The sizes of almost all surgical guides changed after sterilization and disinfection treatments, with between-group differences. Plasma sterilization was more suitable for surgical guide sterilization because of the smaller deformations after treatment.

Multi-Material 3D Printing of Biobased Epoxy Resins.

Additive manufacturing (AM) has revolutionised the manufacturing industry, offering versatile capabilities for creating complex geometries directly from a digital design. Among the various 3D printing methods for polymers, vat photopolymerisation combines photochemistry and 3D printing. Despite the fact that single-epoxy 3D printing has been explored, the fabrication of multi-material bioderived epoxy thermosets remains unexplored. This study introduces the feasibility and potential of multi-material 3D printing by means of a dual-vat Digital Light Processing (DLP) technology, focusing on bioderived epoxy resins such as ELO (epoxidized linseed oil) and DGEVA (vanillin alcohol diglycidyl ether). By integrating different materials with different mechanical properties into one sample, this approach enhances sustainability and offers versatility for different applications. Through experimental characterisation, including mechanical and thermal analysis, the study demonstrates the ability to produce structures composed of different materials with tailored mechanical properties and shapes that change on demand. The findings underscore the promising technology of dual-vat DLP technology applied to sustainable bioderived epoxy monomers, allowing sustainable material production and complex structure fabrication.

Effect of layer thickness and polishing on wear resistance of additively manufactured occlusal splints

ObjectiveTo evaluate the effect of polishing and layering thickness on the wear resistance of 3D-printed occlusal splint materials. MethodsSpecimens with 3 different layer thicknesses (50, 75, 100 µm) were produced in the form of a disc 3 mm thick using V-Print splint resin on a 3D-printer with digital light processing technology. (n = 16 for each thickness) All specimens were washed and cured according to the manufacturer's instructions. Half of the specimens of each layer thickness were polished with silicon carbide papers. All specimens were subjected to 120.000 cycles of a chewing simulator for 2-body wear tests. Before and after the wear test, the specimens were scanned with a laser scanner, and the images were overlaid using a 3D analysis program and the volume loss was calculated. The wear patterns of the specimens were examined under a scanning electron microscope. Statistical evaluation was performed using a Shapiro-Wilk test, 2-way ANOVA, 1-way ANOVA, and Tukey post hoc test (α = 0.05). ResultsWhile polishing had a significant effect (p = 0.003) on the wear volume of the occlusal splints, layer thickness (p = 0.105) and their interaction between polishing and layer thickness (p = 0.620) did not significantly affect the wear volume. Regardless of the polishing, the lowest mean wear was observed for D50 (0.064 mm3), followed by D75 (0.078 mm3), and D100 (0.096 mm3). However, a significant difference was observed only between polished D50 and unpolished D100. ConclusionThe polished 3D-printed occlusal splint resin showed higher wear resistance than the unpolished one, regardless of the layer thickness. Clinical significanceSince different layer thicknesses of 50 µm and greater had no effect on the wear resistance of the material, a layer thickness of 100 µm may be preferred for faster printing. However, polishing occlusal splints may reduce the amount of wear and improve clinical performance.

Comparison of shock absorption capacities of three types of mouthguards: A comparative invitro study.

3D printing processes can be used to manufacture custom-made mouthguards for sports activities. Few studies have compared the impact performance of industrial-created mouthguards with that of custom-made mouthguards manufactured by thermoforming or 3D printing. The objective of this invitro study was to compare the shock absorption capacities of custom-made mouthguards manufactured by 3D printing with industrial mouthguards and thermoformed ethylene vinyl acetate (EVA) mouthguards. For each type of mouthguard, eight samples were produced. 3D-printed mouthguards were manufactured using digital light processing technology. Each mouthguard was subjected to an impact performance test defined by the standard AFNOR XP S72-427, which evaluate maximum deceleration and force transmitted during impact. The thickness of each mouthguard before and after a series of five impacts was measured at the impacted inter-incisal area. The mean maximum decelerations during impact ranged from 129 to 189 g for industrial mouthguards, 287 to 425 g for thermoformed EVA mouthguards, and 277 to 302 g for 3D-printed mouthguards. The mean reduction in mouthguard thickness at the impact zone after five tests was 1.2 mm for industrial mouthguards, 0.6 mm for 3D-printed mouthguards, and 2.2 mm for thermoformed EVA mouthguards. Custom-made 3D printed mouthguards showed slightly better shock absorption ability than thermoformed mouthguards with respect to the indicator proposed in XP S72-427. They seemed to combine the practical advantages of thermoformed mouthguards in sports with better shock absorption capacity and lower cost. Furthermore, they had the least thickness variation during the test, and their shock absorption capacity was the least affected by repeated mechanical tests. Other types of 3D-printing resin materials that will become available must continue to be tested for shock absorption to provide the best protection to users at low cost.

Direct 3D printing of triple-responsive nanocomposite hydrogel microneedles for controllable drug delivery

Hydrogel microneedle patches have emerged as promising platforms for painless, minimally invasive, safe, and portable transdermal drug administration. However, the conventional mold-based fabrication processes and inherent single-functionality of such microneedles present significant hurdles to broader implementation. Herein, we have developed a novel approach utilizing a precursor solution of robust nanocomposite hydrogels to formulate photo-printable inks suitable for the direct 3D printing of high-precision, triple-responsive hydrogel microneedle patches through digital light processing (DLP) technology. The ink formulation comprises four functionally diverse monomers including 2-(dimethylamino)ethyl methacrylate, N-isopropylacrylamide, acrylic acid, and acrylamide, which were crosslinked by aluminum hydroxide nanoparticles (AH NPs) acting as both reinforcing agents and crosslinking centers. This results in the formation of a nanocomposite hydrogel characterized by exceptional mechanical strength, an essential attribute for the 3D printing of hydrogel microneeedle patches. Furthermore, this innovative 3D printing strategy facilitates facile customization of microneedle geometry and patch dimensions. As a proof-of-concept, we employed the fabricated hydrogel microneedles for transdermal delivery of bovine serum albumin (BSA). Importantly, these hydrogel microneedles displayed no cytotoxic effects and exhibited triple sensitivity to pH, temperature and glucose levels, thereby enabling more precise on-demand drug delivery. This study provides a universal method for the rapid fabrication of hydrogel microneedles with smart responsiveness for transdermal drug delivery applications.

Novel 3D printed PZT-based piezoceramics for piezoelectric energy harvesting via digital light processing

Structure optimization is a highly effective way for enhancing the power output of piezoceramics. However, due to the high hardness and brittleness of these materials, traditional manufacturing methods are limited in their ability to optimize structures. Moreover, achieving new designs using the emerging digital light processing (DLP) technology is hindered by poor curing performance of piezoceramic slurry. To overcome these issues, this study proposes an innovative strategy of using the original powders as printing materials for DLP technology. Notably, the use of lead carbonate powders, rather than lead oxide, significantly improves the curing characteristics and printability of ceramic slurry. Additionally, lanthanum oxide powders are introduced as dopants to enhance the electrical properties of PZT ceramics. The printed piezoceramics exhibit excellent piezoelectric and dielectric performance under optimal La3+ content, coupled with superior transduction coefficient, electromechanical coupling factor and output voltages and currents. Our findings suggest a groundbreaking approach for fabricating piezoceramics with high energy-harvesting performance and complicated designed structure via digital light processing.

Assessment of the Development Performance of Additive Manufacturing VPP Parts Using Digital Light Processing (DLP) and Liquid Crystal Display (LCD) Technologies

Non-metallic additive manufacturing technology has seen a substantial improvement in the precision of the parts it produces. Its capability to achieve complex geometries and very small dimensions makes it suitable for integration into strategic industrial sectors, such as aeronautics and medicine. Among additive manufacturing technologies, resin development processes demonstrate enhanced precision when compared to other methods, like filament printing. This study conducts a comparative analysis between digital light processing (DLP) and liquid crystal display (LCD) photopolymerization processes to assess the performance of the technologies and how process parameters affect the accuracy of the resulting parts. The research evaluates the impact of the discretization process used during the digital model export, determining the optimal mesh size and then analyzing the geometric deviations that occur by altering various operating parameters of the process. Statistical methods will be employed to identify the most significant parameters in the manufacturing process. Among other aspects, the precision of manufacturing technologies regarding the movement axis has also been evaluated. Regarding the minimum size of the features that can be fabricated, DLP technology has surpassed LCD technology, successfully producing features as small as 200 µm, compared to 500 µm for LCD technology.

Tailored wrinkles for tunable sensing performance by stereolithography

AbstractConducting polymer hydrogel can address the challenges of stricken biocompatibility and durability. Nevertheless, conventional conducting polymer hydrogels are often brittle and weak due to the intrinsic quality of the material, which exhibits viscoelasticity. This property may cause a delay in sensor response time due to hysteresis. To overcome these limitations, we have designed a wrinkle morphology three‐dimensional (3D) substrate using digital light processing technology and then followed by in situ polymerization to form interpenetrating polymer network hydrogels. This novel design results in a wrinkle morphology conducting polymer hydrogel elastomer with high precision and geometric freedom, as the size of the wrinkles can be controlled by adjusting the treating time. The wrinkle morphology on the conducting polymer hydrogel effectively reduces its viscoelasticity, leading to samples with quick response time, low hysteresis, stable cyclic performance, and remarkable resistance change. Simultaneously, the 3D gradient structure augmented the sensor's sensitivity under minimal stress while exhibiting consistent sensing performance. These properties indicate the potential of the conducting polymer hydrogel as a flexible sensor.

Additive manufacturing of yttria-stabilized zirconia using digital light processing: Green density and surface roughness analysis

The amalgamation of digital light processing (DLP) technology and pressureless sintering has emerged as a promising method for producing delicate, complex, and custom-made yttria-stabilized zirconia (YSZ) components. The procedure consists of fabrication of green part using DLP, debinding to remove the binders and sintering to densify the parts. Explorations in the parameter selection in each step are still far from maturity for producing defect-free densified parts. This study addresses the effect of DLP print parameters on the density of green parts and surface irregularities. DLP printing parameters, such as layer thickness, orientation, and light intensity, were selected, and a central composite design methodology was adopted for the design of experiments to investigate the impact of individual parameter as well as their interactions. The density of the green part decreased with an increase in layer thickness from 10 μm to 70 μm, whereas an increase in density was observed when the part orientation changed from 0 ° to 90°, and the intensity changed from 10 to 50 mW/cm2. The variations in layer thickness and part orientation substantially impact the surface roughness, but variations in intensity have comparatively less influence on the surface roughness. The in-layer and inter-layer voids of the samples fabricated with varying parameters were analyzed using scanning electron microscopy. The minimum surface roughness and maximum green part density responses were obtained using regression equations and a multi-objective optimization strategy. Subsequently, the samples were debinded and sintered to produce high-density zirconia components. To establish the importance of parameter optimization, a comparison of the specimen density and surface irregularity in the green and sintered states was performed for specimens fabricated with optimized parameters and a randomly chosen set of parameters. The novel study provides the parametric relation to fabricate as desired green and sintered density parts along with tuned surface roughness.

UV assisted 3D fabrication of hollow ceramic with single-channel direct ink writing

The inherent brittleness of ceramics poses significant challenges in the fabrication of hollow ceramic fibers, severely constraining their practical applications. In this study, a novel method for creating three-dimensional hollow fiber ceramic structures using UV-assisted single-channel direct ink writing was demonstrated. A concentric single-channel nozzle featuring shell/core structure was devised through the coaxial embedding method, and this specially designed nozzle was manufactured using digital light processing technology. During the UV-assisted direct ink writing process, the photosensitive ceramic slurry can be rapidly cured in place under the irradiation of UV light, ensuring high fidelity of the printed components. The hollow fiber structure produced in this study has a circular, pentagram, triangular and quadrilateral inner core, which can be adjusted according to the designed nozzle structure. This approach facilitates a straightforward and expedited creation of scaffolds featuring small-diameter hollow fiber structures, broadening the scope of potential applications for direct ink writing.

Optimizing the properties of vat photopolymerization 3D-printed SiC ceramics by multi-infiltration

ABSTRACT Digital Light Processing (DLP) technology is a highly effective molding method for creating complex structural parts. However, the low solid content of SiC stereolithography slurry has been found to diminish the mechanical properties of the ceramic, regardless of whether it is sintered by Reactive Melt Infiltration (RMI) or Precursor Infiltration and Pyrolysis (PIP). This poses a significant challenge in improving the mechanical properties of SiC ceramics manufactured through DLP additive manufacturing. In response to this challenge, a novel method of RMI combined with infiltration is proposed in this study. The process involves the filling of the pores of the green body with pyrolytic carbon from PR or pyrolytic SiC from LHBPCS through circular infiltration, effectively increasing the content of SiC in the ceramics after reaction. Notably, the elastic modulus of RM-P2 and RM-L2 samples increased by 37.39% and 33.91%, respectively, demonstrating the potential of this method for preparing ceramics with high SiC content through stereolithography additive manufacturing. This innovative approach holds promise for overcoming the limitations previously associated with SiC ceramics produced through DLP additive manufacturing, opening up new possibilities for the development of high-performance SiC-based components.

Biopolymeric corneal lenticules by digital light processing based bioprinting: a dynamic substitute for corneal transplant

Digital light processing (DLP) technology has gained significant attention for its ability to construct intricate structures for various applications in tissue modeling and regeneration. In this study, we aimed to design corneal lenticules using DLP bioprinting technology, utilizing dual network bioinks to mimic the characteristics of the human cornea. The bioink was prepared using methacrylated hyaluronic acid and methacrylated gelatin, where ruthenium salt and sodium persulfate were included for mediating photo-crosslinking while tartrazine was used as a photoabsorber. The bioprinted lenticules were optically transparent (85.45% ± 0.14%), exhibited adhesive strength (58.67 ± 17.5 kPa), and compressive modulus (535.42 ± 29.05 kPa) sufficient for supporting corneal tissue integration and regeneration. Puncture resistance tests and drag force analysis further confirmed the excellent mechanical performance of the lenticules enabling their application as potential corneal implants. Additionally, the lenticules demonstrated outstanding support for re-epithelialization and stromal regeneration when assessed with human corneal stromal cells. We generated implant ready corneal lenticules while optimizing bioink and bioprinting parameters, providing valuable solution for individuals suffering from various corneal defects and waiting for corneal transplants.

3D Printed Porous Zirconia Biomaterials based on Triply Periodic Minimal Surfaces Promote Osseointegration In Vitro by Regulating Osteoimmunomodulation and Osteo/Angiogenesis.

The triply periodic minimal surface (TPMS) is a highly useful structure for bone tissue engineering owing to its nearly nonexistent average surface curvature, high surface area-to-volume ratio, and exceptional mechanical energy absorption properties. However, limited literature is available regarding bionic zirconia implants using the TPMS structure for bone regeneration. Herein, we employed the digital light processing (DLP) technology to fabricate four types of zirconia-based TPMS structures: P-cell, S14, IWP, and Gyroid. For cell proliferation, the four porous TPMS structures outperformed the solid zirconia group (P-cell > S14 > Gyroid > IWP > ZrO2). In vitro assessments on the biological responses and osteogenic properties of the distinct porous surfaces identified the IWP and Gyroid structures as promising candidates for future clinical applications of porous zirconia implants because of their superior osteogenic capabilities (IWP > Gyroid > S14 > P-cell > ZrO2) and mechanical properties (ZrO2 > IWP > Gyroid > S14 > P-cell). Furthermore, the physical properties of the IWP/Gyroid surface had more substantial effects on bone immune regulation by reducing macrophage M1 phenotype polarization while increasing M2 phenotype polarization compared with the solid zirconia surface. Additionally, the IWP and Gyroid groups exhibited enhanced immune osteogenesis and angiogenesis abilities. Collectively, these findings highlight the substantial impact of topology on bone/angiogenesis and immune regulation in promoting bone integration.

DLP printed 3D gyroid structure: Mechanical response at meso and macro scale

Rapid prototyping (RP) technology enables the fabrication of complex geometries, making lattice structures increasingly popular. Lattice structures, known as cellular materials, have garnered significant attention over the past two decades due to their ability to optimise mass distribution in components. These structures excel in mechanical properties, catering to energy absorption (bending-dominated structures) and structural performance (stretch-dominated structures). In this paper, we investigate the behaviour of stretch-dominated lattice structures using periodic surface models, specifically focusing on sheet-based Gyroid cells, to allow for a more efficient macroscale modelling. We study cells and scaffolds of different sizes, considering various triply periodic minimal surface thicknesses and relative densities ranging from approximately 0.2 to 0.65. We explore load applications in directions different from the unit cell's principal axes and analyse the strain rate effect on both bulk and cellular material. The lattice structures are manufactured using epoxy resin and digital light processing (DLP) technology. In the range of relative density investigated, both in quasi-static and dynamic conditions, a linear trend is observed for Young's modulus and compression yield strength. To extend the quasi-static results to the dynamic regime, we employ a more generalized normalization technique. This approach divides Young's modulus and compression yield strength by the behaviour of the base material at a specific strain rate, facilitating the correlation of mechanical properties across the two loading regimes. Based on experimental findings, we implemented and calibrated a bi-linear material model for describing, in macroscale, triply periodic minimal surface (TPMS) Gyroid structures. The model coefficients are parameterized with respect to relative density. In addition, the presented material law was compared with that proposed by Gibson-Ashby. Furthermore, we evaluated the anisotropy of both the base material and the unit cell. The first one is done by testing the 3D printed samples in directions different from the printing one, the latter by using the Zener factor. The anisotropy evaluation confirmed the isotropic behaviour of the unit cell within the range of relative density and test conditions investigated. Finally, we perform linear elastic 3D macroscopic and mesoscopic model simulations for combined shear-compression tests using the implemented bi-linear material model and the anisotropic stiffness matrix (obtained through the homogeneous formulation) for the macroscale, and the base material for the mesoscopic one. The results demonstrate the suitability of the proposed equivalent material model for studying the TPMS Gyroid structure in the elastic regime, both in quasi-static and dynamic states. This allows for an efficient FE modelling process of complex lattice structures.

Flame Retardant Additives in Polylactic Acid (PLA) Photopolymer Resin for 3D Printing Digital Light Processing (DLP)

Digital light processing (DLP) technology has been developed based on stereolithography (SLA) 3D-printing principle. The biodegradable and low-cost polylactic-acid (PLA) has so far been used as polymeric material for photopolymer resin in SLA and DLP. To achieve functional SLA-processed product, the properties of such PLA has been improved, with the aim to make it flame retardant, less viscous, and having light transmittance characteristics. In this study, the liquid raw PLA photopolymer was changed by adding different contents of Ammonium Phosphate (APP), melamine cyanurate (MCA), Aluminum Tri-hydroxide (Al2O3) and Nano-silicon dioxide (SiO2) additives. The solid PLA nanocomposite specimens were printed by using DLP device according to the standard geometry for burning test UL-94 to evaluate its flame-retardant property. In addition, the printing product and residue after burning test was analyzed for their morphological characteristic by using SEM. The results showed that the low weight fraction of MCA showed excellent performance. PLA/MCA successfully kept green body form until the sintering temperature of stainless steel was achieved. It can become a reference for application DLP 3D printing products in the casting and sintering process.

Experimental investigation of stereolithography and digital light processing additive manufactured pallets

Abstract Pallets are a tertiary form of packaging used for stacking, storing, protecting, or transporting goods in supply chains. They are utilized as a base for the unitization of goods for logistics and warehousing. Moreover, pallets can be manufactured using wood, plastic, metal, and corrugated paper, which can be used as material-handling equipment. With several products being transported worldwide and with year-on-year growth, it would be beneficial to make lightweight pallets. Such pallets are recyclable, easy to clean, cheap, and durable to maintain and store. Though most of the pallets are widely available for basic purposes, applications involving high-end bio-packings and transportation of special chemicals require specialized pallets to be manufactured like polymers to ensure a negligible chemical reaction, light in weight, and attenuation in freight capacity, thereby widespread reduction in wastage. With advancements, job to job and immediate requirements, additive manufacturing has the potential to close the gap for jobs with short lead times. If the design process of new pallets has limits the creation of specific codes, the transitions will be smoother in rapid prototyping. This work describes the development of polymer pallets by taking advantage of stereolithography (SLA) and digital light processing (DLP) technology for 3D printing pallets in correlation to injection moulding. After the pallets are designed and manufactured, AM technologies can be applied to specified standards, and the pallets then undergo tensile strength, elongation, and hardness tests. The analysis was carried out for configurable geometries adapting to fork lifting, conveyor, racking, and stacking conditions. Analytical and numerical solutions were carried out to understand the stress and deflections for each geometry and its wide range of applications for pallets.

The Effect of Different System Parameters on the Movement of Microbial Cells Using Light-Induced Dielectrophoresis.

The manipulation of single particles remains a topic of interest with many applications. Here we characterize the impact of selected parameters on the motion of single particles thanks to dielectrophoresis (DEP) induced by visible light, in a technique called Light-induced Dielectrophoresis, or LiDEP, also known as optoelectronic tweezers, optically induced DEP, and image-based DEP. Baker's yeast and Candida cells are exposed to an electric field gradient enabled by shining a photoconductive material with a specific pattern of visible light, and their response is measured in terms of the average cell velocity towards the gradient. The impact on cell velocity when varying the shape and color of the light pattern, as well as the distance from the cell to the pattern, is presented. The experimental setup featured a commercial light projector featuring digital light processing (DLP) technology but mechanically modified to accommodate a 40× microscope objective lens. The minimal resolution achieved on the light pattern was 8 µm. Experimental results show the capability for single cell manipulation and the possibility of using different shapes, colors, and distances to determine the average cell velocity.

Analysis on Modern Application and Development Demand of Electronic Information Engineering

In recent years, there has not been a large-scale promotion of high-precision technology, resulting in the core technology can not be effectively applied in enterprises and related industries still need to further develop electronic information engineering. In this regard, combined with the market economic development situation, intelligence and digitalization has become the main direction of the development of electronic information engineering, through the construction of a perfect information management platform, can make efficient use of resources, a wide range of popularization of science and technology. In the context of the Internet era, people's daily life has changed dramatically, especially the information transmission will become more rapid, efficient and convenient. In the expanding scope of application of computer network technology, can realize the efficient transmission and sharing of information, in the field of electronic information engineering, through the application of computer network technology can effectively ensure the quality of information, and lay a good foundation for the smooth progress of information engineering reform work. In the process of promoting the efficient integration of the two, can make the electronic information engineering needs to be met, which should also increase the integration of resources, computer network technology research and development and application work, so that people's daily lives to enjoy more convenient conditions. The application of digital information processing technology can break through the traditional mode of communication in the application of the process of various shortcomings, prompting the development of digital information engineering more and more rapid. The application of this technology can make all walks of life for information activities to fully meet the needs of all sectors of society, to ensure the smooth and stable information construction activities, so we need to combine the actual situation to further optimize the digital signal construction system, so that it plays a greater role in electronic information engineering. Based on the above situation, this paper focuses on the innovation and development of modern electronic information engineering.