Diffusion-ordered Spectroscopy Research Articles

Potential of Benchtop NMR for the Determination of Polymer Molar Masses, Molar Mass Distributions, and Chemical Composition Profiles by Means of Diffusion-Ordered Spectroscopy, DOSY.

The determination of molar masses and their distributions is crucial in polymer synthesis and design. This work presents the current performance and limitations of diffusion-ordered spectroscopy (DOSY) on a low-field (benchtop) NMR spectrometer (at 90MHz) as an alternative to size exclusion chromatography (SEC) for determining diffusion coefficient distributions (DCDs) and molar mass distributions (MMDs). After optimization for narrowly distributed homopolymers, MMDs obtained with inverse Laplace transformation (ILT) and log-normal distribution are compared with average molar masses obtained with mono- and bi-exponential fits, as well as MMDs obtained from SEC. This approach enables ILT to determine DCDs and MMDs even for bimodal homopolymers with fully spectrally overlapping signals and block copolymers with various chemical compositions, for which chemical composition profiles are determined. The feasibility of low-field diffusion NMR with samples dissolved in non-deuterated solvents is further demonstrated and methods for solvent suppression are discussed.

What Is the Molecular Weight of "High" Molecular Weight Dissolved Organic Matter?

The use of ultrafiltration to isolate high molecular weight dissolved organic matter (HMWDOM) from seawater is a fundamental tool in the environmental organic chemist's toolbox. Yet, important characteristics of HMWDOM relevant to its origin and cycling, such as its molecular weight distribution, remain poorly defined. We used diffusion-ordered NMR spectroscopy coupled with mixed-mode chromatography to separate and characterize two major components of marine HMWDOM: acylpolysaccharides (APS) and high molecular weight humic substances (HS). The molecular weights (MWs) of APS and HS both fell within distinct, narrow envelopes; 2.0-16 kDa for APS and 0.9-6.5 kDa for HS. In water samples from the North Pacific Ocean the average MW of both components decreased with depth through the mesopelagic. However, the minimum MW of APS was >2 kDa, well above the molecular weight cutoff of the ultrafilter, suggesting APS removal processes below 2 kDa are highly efficient. The MW distribution of APS shows only small variations with depth, while the MW distribution of HS narrowed due to removal of HMW components. Despite the narrowing of the MW distribution, the concentration of HS did not decrease with depth between 15 and 915 m. This suggests that HMW HS produced in surface waters was either degraded into lower MW compounds without significant remineralization, or that HMW HS was remineralized but replaced by an additional source of HS in the mesopelagic ocean. Based on these results, we propose potential pathways for the production and removal of these major components of HMWDOM.

Study of the preparation, characterization, and solubility of lidocaine complexed with 5-sulfosalicylic acid dihydrate

Objective: This study was to prepare solid dispersions of lidocaine (Lid) with 5-sulfosalicylic acid dihydrate (SSA) by freeze-drying (freeze-dried [FD] Lid/SSA = 1/1) and to evaluate their physical properties. Methods: Here, we evaluated the physicochemical properties and solubility of solid dispersions of lidocaine (Lid) and 5-sulfosalicylic acid dihydrate (SSA) prepared by freeze-drying (freeze-dried [FD] Lid/SSA = 1/1). Results: Differential scanning calorimetry measurements showed that after freeze-drying, the endothermic peak due to Lid melting, the dehydration peak, and the endothermic peak due to SSA melting disappeared. Powder X-ray diffraction results showed that the characteristic Lid and SSA peaks disappeared after freeze-drying, indicating a halo pattern. The near-infrared spectroscopy results suggested that Lid-derived -NH and -CH groups and the Lid-derived -OH and -CH groups from the SSA peak shifted and broadened after freeze-drying, suggesting their involvement in complex formation through Lid/SSA intermolecular interactions. Nuclear Overhauser effect spectroscopy-nuclear magnetic resonance (NMR) measurements showed a cross-peak due to the interaction between the Lid-derived -CH group and the SSA-derived -OH group, suggesting hydrogen bonding. Diffusion-ordered spectroscopy NMR measurements showed that the diffusion coefficients of Lid and SSA aggregated in FD Lid/SSA, suggesting a change in Lid dispersibility in the solvent owing to the formation of a complex with SSA. The solubility of FD Lid/SSA was approximately 88 mg/mL (∼20-fold higher than that of Lid). Conclusions: These findings suggest that complex formation occurred in FD Lid/SSA; this enhanced the solubility of this dispersion.

Conformational Landscape of NADH and Ion Binding in Water/DMSO Mixtures via 31P NMR Spectroscopy.

This study reports on the conformational states of nicotinamide adenine dinucleotide (NADH) in water/DMSO mixtures and examines the influence of ion binding. We observe evidence of conformational changes through a series of NMR techniques, including 31P NMR relaxation (R1 and R2), chemical exchange saturation transfer (CEST), and diffusion-ordered spectroscopy (DOSY) experiments. The observed variation of the conformational states is indicative of the solvent's influence on NADH's structural flexibility. The experimental findings, in combination with viscosity data, are shown to be in line with findings from earlier molecular dynamics studies. The reported observations emphasize the critical role of the solvent environment in determining the conformational states of NADH and similar molecules with relevance for the biophysiological context. The results found herein can help in studying the biophysical behavior of NADH and similar biomolecules and their associated metabolic pathways under various solvent conditions.

Intact NMR Approach Quickly Reveals Synchronized Microstructural Changes in Oil-in-Water Nanoemulsion Formulations

A soft-core oil-in-water (o/w) nanoemulsion (NE) is composed of nanometer (nm) sized oil droplets, stabilized by a surfactant layer and dispersed in a continuous bulky water phase. Characterization of the o/w NE molecule arrangements non-invasively, particularly the drug phase distribution (DPD) and its correlation to oil globule size (OGS), remains a challenge. Here we demonstrated the analytical methods of intact 19F Nuclear Magnetic Resonance (NMR) and 1H diffusion ordered spectroscopy (DOSY) NMR for their specificity in measuring DPD and OGS, respectively, on three NE formulations containing the active ingredient difluprednate (DFPN) at the same concentration. The results illustrated synchronized molecular rearrangement reflected in the DPD and OGS upon alterations in formulation. Addition of surfactant resulted in a higher DPD in the surfactant layer, and concomitantly smaller OGS. Mechanic perturbation converted most of the NE globules to the smaller thermodynamically stable microemulsion (ME) globules, changing both DPD and OGS to ME phase. These microstructure changes were not observed using 1D 1H NMR; and dynamic light scattering (DLS) was only sensitive to OGS of ME globule in mechanically perturbed formulation. Collectively, the study illustrated the specificity and essential role of intact NMR methods in measuring the critical microstructure attributes of soft-core NE systems quickly, accurately, and non-invasively. Therefore, the selected NMR approach can be a unique diagnostic tool of molecular microstructure or Q3 property in o/w NE formulation development, and quality assurance after manufacture process or excipient component changes.Graphical abstract

The use of carbodicarbene for bio-based polyester synthesis via ring-opening copolymerization of cyclic anhydrides and epoxides

Alternating ring-opening copolymerization (ROCOP) of epoxides and cyclic anhydrides was investigated using carbodicarbene (CDC) as a single-component organic initiator. CDC produced various polyesters with different combinations of monomers, including bio-based monomers. The synthesized polyesters exhibited narrow dispersity and a wide range of glass transition temperatures. Moreover, a diblock copolyester was synthesized using self-switchable polymerization (ROCOP of the cyclic anhydride/epoxide, and ring-opening polymerization of lactone) in a one-pot synthesis. The formation of a terpolymer product was confirmed by diffusion-ordered spectroscopy and thermal gravimetric analysis.

CO2 derived ABA triblock all-polycarbonate thermoplastic elastomer with ultra-high elastic recovery

Although triblock polycarbonate thermoplastic elastomers (TPEs) have recently attracted great interests due to their biodegradability, insufficient attentions have been paid to improving the elastomeric properties. Through a tandem reaction strategy involving CO2 / allyl glycidyl ether (AGE) / cyclohexene oxide (CHO), poly(cyclohexene carbonate)-b-poly(allyl glycidyl ether carbonate)-b-poly(cyclohexene carbonate) (PCAC) is successfully synthesized using a metal-free Lewis acid-base pair catalyst. The synthesized PCACs are pure well-defined ABA triblock all-polycarbonate, which is supported by 1H NMR, gel permeation chromatography (GPC), and diffusion-ordered spectroscopy (DOSY). A simple modification by grafting alkylthiol chains to PCAC results in excellent TPEs named PCAC-g-S-CaH2a+1 (PCASaC). The synthesized TPEs are characterized by atomic force microscopy (AFM), thermogravimetric analysis (TG), differential scanning calorimetry (DSC), and mechanical test. They demonstrate a semi-network and semi-domain phase separation structure, wide service temperature range, good strength, high elongation, and extremely high elastic recovery properties. This low-cost, biodegradable, high-performance TPE shows great potential for applications in biomedical, wearable products, sports equipment, and other fields.

Water Confinement on Polymer Coatings Dictates Proton-Electron Transfer on Metal-Catalyzed Hydrogenation of Nitrite.

Enzymes can precisely control the speed and selectivity of chemical reactions by modifying locally the solvent-reactant interactions. To extrapolate these attributes to heterogeneous catalysts, we have employed thermoresponsive poly n-isopropylacrylamide (p-NIPAM) brushes bonded to silica spheres containing palladium. These polymers can form hydrogen bonds with water molecules at low temperatures (<32 °C) allowing the polymer to stay swollen. Detailed reaction kinetics of nitrite hydrogenation showed that p-NIPAM decreases the apparent activation barrier by a factor of 3 at low temperatures. Diffusion-ordered spectroscopy nuclear magnetic resonance and ab initio molecular dynamics simulations showed that when p-NIPAM is present, water molecules near the surface are less mobile. This confinement perturbs the water interaction with the metal, reducing the barrier for the proton-electron transfer reduction of nitrite. Notably, this enhancement vanishes at high temperature as the polymer collapses on itself exposing the Pd to unconfined water. The fully reversible nature of this process opens the door for creating homeostatic catalysts with controlled water-confinement.

Oligo(styryl)benzenes liposomal AIE-dots for bioimaging and phototherapy in an in vitro model of prostate cancer

Whilst the development of advanced organic dots with aggregation-induced emission characteristics (AIE-dots) is being intensively studied, their clinical translation in efficient biotherapeutic devices has yet to be tackled. This study explores the synergistic interplay of oligo(styryl)benzenes (OSBs), potent fluorogens with an increased emission in the aggregate state, and Indocyanine green (ICG) as dual Near Infrared (NIR)-visible fluorescent nanovesicles with efficient reactive oxygen species (ROS) generation capacity for cancer treatment using photodynamic therapy (PDT). The co-loading of OSBs and ICG in different nanovesicles has been thoroughly investigated. The nanovesicles’ physicochemical properties were manipulated via molecular engineering by modifying the structural properties of the lipid bilayer and the number of oligo(ethyleneoxide) chains in the OSB structure. Diffusion Ordered Spectroscopy (DOSY) NMR and spectrofluorometric studies revealed key differences in the structure of the vesicles and the arrangement of the OSB and ICG in the bilayer. The in vitro assessment of these OSB-ICG nanovesicles revealed that the formulations can increase the temperature and generate ROS after photoirradiation, showing for the first time their potential as dual photothermal/photodynamic (PTT/PDT) agents in the treatment of prostate cancer. Our study provides an exciting opportunity to extend the range of applications of OSB derivates to potentiate the toxicity of phototherapy in prostate and other types of cancer.

Metabolomics analysis using matrix-assisted diffusion-ordered spectroscopy (DOSY) and its application in acrylamide-induced cardiovascular toxicity

Untargeted NMR-based metabolomics strategies are increasingly applied for metabolite screening in a wide variety of medical conditions. However, the identification of metabolites remains a great challenge in NMR metabolomics research. Here, we used matrix-assisted diffusion-ordered spectroscopy (DOSY) to identify new biomarkers in body fluids. DOSY-based metabolomics can exploit the unique strengths of NMR and, thanks to improvements in its resolution, can be successfully used to address a significantly wider range of biological issues. In this study, a metabolite model consisting of ten common metabolites was employed to optimize the matrix-assisted DOSY experimental parameters. Polyvinylpyrrolidone (PVP), a high-molecular-weight polymer, was found to be the most appropriate matrix with which to accomplish the separation of the mixture components. 1H NMR and PVP-assisted DOSY analyses were performed to characterize the metabolic profile of serum samples from acrylamide (ACR)-treated rats and study the mechanism of ACR-induced cardiovascular toxicity. Biomarker identification by 1H NMR and PVP-assisted DOSY yielded similar results. However, multivariate statistical analysis showed that, compared with 1H NMR, PVP-assisted DOSY achieved a better discrimination of the serum samples obtained from rats treated with different doses of ACR. A total of 11 differential metabolites were identified. An enrichment analysis of the metabolic pathways showed that, in rats treated with a high dose of ACR, the glutamate and glutathione metabolic pathways and the energy metabolism pathway of the tricarboxylic acid cycle were mainly affected.

Impact of Single Acyclic Phosphonate Nucleotide (ZNA) Modifications on DNA Duplex Stability.

An acyclic phosphonate-linked nucleic acid backbone (ZNA) demonstrated the capability to support duplex formation and propagate genetic information in vivo, unveiling its potential for evolution into a synthetic genetic system (XNA). To determine the structural impact of such modification, modified Dickerson Drew DNA dodecamers (DDDs) were prepared by solid phase synthesis, each containing either an (R) or (S) isomeric form of a cytosine ZNA nucleotide. While the DDD is known to adopt a stable duplex, both duplex and hairpin forms were simultaneously observed for both modified oligonucleotides by NMR spectroscopy over a broad temperature range (5-65 °C). Diffusion-ordered spectroscopy (DOSY) experiments allowed to separate duplex and hairpin signals based on the different diffusion constants of both conformational states. For the oligomer containing (R)-ZNA, only the duplex form occurred at 5 °C, while it was not possible to determine by NMR a single hairpin conformation at higher temperatures. In the case of the (S)-ZNA nucleoside modified oligomer, both hairpin and duplex forms were observable at 0 °C, while a single hairpin conformation was detected at 37 °C, suggesting a higher destabilizing effect on dsDNA.

Molecular insights into fragrance release from SDS and SLES micelles

Understanding the interaction between fragrance and surfactant micelles is essential for formulators to develop performing fragrant products. The equilibrium of fragrances in micellar solution of two commonly used surfactants in home and body care industries, namely sodium dodecyl sulphate (SDS) and sodium lauryl ether sulphate (SLES), has been investigated. The difference between SDS and SLES in the release of fragrant compounds is assessed by headspace measurements and explained at a molecular level by the different solubilization sites of the perfume within the micellar systems. Diffusion-Ordered Nuclear Magnetic Resonance Spectroscopy (DOSY NMR) shows that SLES micelles solubilize less fragrance than SDS. Subsequently, a shift from fragrance positioning through the water phase from SDS to SLES system is shown with COSMOmic calculations. This study brings knowledge on fragrance/surfactant interactions and shows the interest of using a computational method to screen and compare fragranced surfactants systems allowing formulators to anticipate the performance of their products.

Dual Structure of a Vanadyl-Based Molecular Qubit Containing a Bis(β-diketonato) Ligand.

We designed [VO(bdhb)] (1') as a new electronic qubit containing an oxovanadium(IV) ion (S = 1/2) embraced by a single bis(β-diketonato) ligand [H2bdhb = 1,3-bis(3,5-dioxo-1-hexyl)benzene]. The synthesis afforded three different crystal phases, all of which unexpectedly contain dimers with formula [(VO)2(bdhb)2] (1). A trigonal form (1h) with a honeycomb structure and 46% of solvent-accessible voids quantitatively transforms over time into a monoclinic solvatomorph 1m and minor amounts of a triclinic solventless phase (1a). In a static magnetic field, 1h and 1m have detectably slow magnetic relaxation at low temperatures through quantum tunneling and Raman mechanisms. Angle-resolved electron paramagnetic resonance (EPR) spectra on single crystals revealed signatures of low-dimensional magnetic behavior, which is solvatomorph-dependent, being the closest interdimer V···V separations (6.7-7.5 Å) much shorter than intramolecular V···V distances (11.9-12.1 Å). According to 1H diffusion ordered spectroscopy (DOSY) and EPR experiments, the complex adopts the desired monomeric structure in organic solution and its geometry was inferred from density functional theory (DFT) calculations. Spin relaxation measurements in a frozen toluene-d8/CD2Cl2 matrix yielded Tm values reaching 13 μs at 10 K, and coherent spin manipulations were demonstrated by Rabi nutation experiments at 70 K. The neutral quasi-macrocyclic structure, featuring nuclear spin-free donors and additional possibilities for chemical functionalization, makes 1' a new convenient spin-coherent building block in quantum technologies.

Using Nuclear Magnetic Resonance to Troubleshoot a Stability Issue in a Real-World Formulation Chassis-Application to Consumer Oral Healthcare.

With direct application to current and future consumer healthcare products, this research sheds light on the importance of packaging and its potential effects on both Active Pharmaceutical Ingredient (API) delivery and stability. Industrially sourced, proprietary experimental formulations (PEFs), specifically oral cleansers, based on salicylic acid and hydrogen peroxide, discolored over time at different rates, depending on packaging type used. This discoloration stemmed from an interplay of two factors, involving both spontaneous formulation degradation and the interaction of both degradants and salicylic acid with the internal surface of the packaging. This manuscript reports on the investigation to uncover the origins of discoloration. To investigate this real-world, industrial pipeline problem, we exploited the high dimensionality and simple sample preparation uniquely afforded by NMR. Using a combination of 1D/2D NMR and diffusion-ordered NMR spectroscopy (DOSY) to leverage molecular mass estimations from, we not only quickly confirmed the identities of these degradants, but also assessed their formation as a function of temperature and pH, providing insight into the mechanisms underlying their formation. We were able to identify catechol as the main source of discoloration over a period of several weeks, being formed at the ppm level. Furthermore, we evaluated the formulation-container interaction, employing NMR, ICP-MS, and ATR-IR. Despite this comprehensive analysis, the root causes of discoloration could only tentatively be assigned to a surface Ti complex of salicylic acid and other hydroxy carboxylic acids. Through the understanding of formulation degradation pathways, we were able to support further toxicology assessment, vital to both consumer safety and the manufacturer. This work underscores the invaluable role of NMR in the analysis of intricate proprietary mixtures with a consumer-centric purpose. Our findings demonstrate that conventional analytical techniques falter in the face of such complexity, requiring extensive preparation and pre-analytical processing, highlighting the novelty and crucial relevance of NMR research to manufacturers and consumers. Such an analysis is of value in the pursuit of materials within the consumer-healthcare space, which meet the requirements for successful recycling or re-use.

Online coupling of liquid chromatography and two-dimensional diffusion ordered spectroscopy for the analysis of oligostyrenes

The aim of this study was to introduce a powerful coupling of Liquid Adsorption Chromatography (LAC) and Diffusion-Ordered Spectroscopy (DOSY) for comprehensive structure analysis. This new hyphenation approach facilitated the simultaneous separation of a polymer mixture and the determination of molar masses within a single 3D experiment. The online coupling of High-Performance Liquid Chromatography (HPLC) and two-dimensional DOSY-NMR will be called 3D-LAC-NMR-DOSY experiment. Our methodology enabled the chromatographic separation of analytes based on their chemical heterogeneity, and provided accurate molar masses of the analytes through 2D-DOSY. This new method was demonstrated on a polystyrene oligomer mixture. In this case, the oligostyrenes could be separated with LAC according to their tacticity and chain length in protonated acetonitrile as eluent and DOSY measurements provided the molar masses of each oligomer. In order to show the power of the 3D-LAC-NMR-DOSY method, the comparison to 2D-DOSY, 3D-DOSY and LAC-NMR was separately evaluated. Furthermore, the recently published solvent-independent molar mass calibration of diffusion coefficients was also successfully applied in our LAC-DOSY studies for molar mass predictions of the oligomers in acetonitrile. The predicted molar masses were in good agreement with the LAC-DOSY measurements and were verified by calibrations of diffusion coefficients and mass spectrometry. Finally, this pioneering 3D technique offers a powerful new tool for advancing structure analysis and enhancing our understanding of complex systems such as oligostyrenes.

MaDDOSY (Mass Determination Diffusion Ordered Spectroscopy) using an 80MHz Bench Top NMR for the Rapid Determination of Polymer and Macromolecular Molecular Weight.

Measurement of molecular weight is an integral part of macromolecular and polymer characterization which usually has limitations. Herein, this article presents the use of a bench-top 80MHz Nuclear Magnetic Resonance (NMR) spectrometer for diffusion-ordered spectroscopy as a practical and rapid approach for the determination of molecular weight/size using a novel solvent and polymer-independent universal calibration.

Effects of Drug Conjugation on the Biological Activity of Single-Chain Nanoparticles.

The field of single-chain nanoparticles (SCNPs) continues to mature, and an increasing range of reports have emerged that explore the application of these small nanoparticles. A key application for SCNPs is in the field of drug delivery, and recent work suggests that SCNPs can be readily internalized by cells. However, limited attention has been directed to the delivery of small-molecule drugs using SCNPs. Moreover, studies on the physicochemical effects of drug loading on SCNP performance is so far missing, despite the accepted view that such small nanoparticles should be significantly affected by the drug loading content. To address this gap, we prepared a library of SCNPs bearing different amounts of a covalently conjugated therapeutic drug-sulfasalazine (SSZ). We evaluated the impact of the conjugated drug loading on both the synthesis and biological activity of SCNPs on pancreatic cancer cells (AsPC-1). Our results reveal that covalent drug conjugation to the side chains of the SCNP polymer precursor interferes with chain collapse and cross-linking, which demands optimization of reaction conditions to reach high degrees of cross-linking efficiencies. Small-angle neutron scattering and diffusion-ordered spectroscopy nuclear magnetic resonance (DOSY NMR) analyses reveal that SCNPs with a higher drug loading display larger sizes and looser structures, as well as increased hydrophobicity associated with a higher SSZ content. Increased SSZ loading led to reduced cellular uptake when assessed in vitro, whereby SCNP aggregation on the surface of AsPC-1 cells led to reduced toxicity. This work highlights the effects of drug loading on the drug delivery efficiency and biological behavior of SCNPs.

Spatially encoded pure-shift diffusion-ordered NMR spectroscopy yielded by chirp excitation

Spatially-encoded diffusion-ordered NMR spectroscopy (SPEN-DOSY) has emerged as a new time-efficient tool for the analysis of mixtures of small molecules in solution. Time efficiency is achieved using the concept of spatial parallelization of the effective gradient area, instead of the sequential incrementation used in conventional diffusion experiments. The data acquired with such sequences are then usually processed to extract diffusion coefficients, but cases when peak overlap in the 1H spectrum are difficult to address. Such limitation in conventional diffusion experiments is addressed via using the Pure Shift Yielded by CHirp Excitation (PSYCHE)-iDOSY sequence. Here we have adapted the PSYCHE-iDOSY sequence by using echo planar spectroscopic imaging (EPSI) to acquire SPEN-DOSY data. The pure shift mode of PSYCHE separates the overlapped components and a modified Stejskal-Tanner equation is used to extract the corresponding diffusion coefficient. The primary results obtained with the above-mentioned mixtures seem to open the possibility of separating complex mixtures in less time than PSYCHE-iDOSY.

Quantitative at-line monitoring of enzymatic hydrolysis using benchtop diffusion nuclear magnetic resonance spectroscopy.

Benchtop diffusion nuclear magnetic resonance (NMR) spectroscopy was used to perform quantitative monitoring of enzymatic hydrolysis. The study aimed to test the feasibility of the technology to characterize enzymatic hydrolysis processes in real time. Diffusion ordered spectroscopy (DOSY) was used to measure the signal intensity and apparent self-diffusion constant of solubilized protein in hydrolysate. The NMR technique was tested on an enzymatic hydrolysis reaction of red cod, a lean white fish, by the endopeptidase alcalase at 50°C. Hydrolysate samples were manually transferred from the reaction vessel to the NMR equipment. Measurement time was approximately 3 min per time point. The signal intensity from the DOSY experiment was used to measure protein concentration and the apparent self-diffusion constant was converted into an average molecular weight and an estimated degree of hydrolysis. These values were plotted as a function of time and both the rate of solubilization and the rate of protein breakdown could be calculated. In addition to being rapid and noninvasive, DOSY using benchtop NMR spectroscopy has an advantage compared with other enzymatic hydrolysis characterization methods as it gives a direct measure of average protein size; many functional properties of proteins are strongly influenced by protein size. Therefore, a method to give protein concentration and average size in real time will allow operators to more tightly control production from enzymatic hydrolysis. Although only one type of material was tested, it is anticipated that the method should be applicable to a broad variety of enzymatic hydrolysis feedstocks.

A dynamic covalent approach to [PtnL2n]2n+ cages.

A dynamic covalent approach was exploited to generate a family of homometallic [PtnL2n]2n+ cage (predominantly [Pt2L4]4+ systems) architectures. The family of platinum(II) architectures were characterized using 1H nuclear magnetic resonance (NMR) and diffusion ordered spectroscopy (DOSY), electrospray ionization mass spectrometry (ESI-MS) and the molecular structures of two cages were determined by X-ray crystallography.