Radiation Hardness Of Detectors Research Articles

Design and Simulation of Gamma Spectrometry Experiments in the CROCUS Reactor

Gamma rays in nuclear reactors, arising either from fission or decay processes, significantly contribute to the heating and dose of the reactor components. Zero power research reactors offer the possibility to measure gamma rays in a purely neutronic environment, allowing for validation experiments of computed spectra, dose estimates, reactor noise and prompt to delayed gamma ratios. This data then contributes to models, code validation and photo atomic nuclear data evaluation. In order to contribute to aforementioned experimental data, gamma detection capabilities are being added to the CROCUS reactor facility. The CROCUS reactor is a two-zone, uranium-fueled light water moderated facility operated by the Laboratory for Reactor Physics and Systems Behaviour (LRS) at the Swiss Federal Institute of Technology Lausanne (EPFL). With a maximum power of 100W, it is a zero power reactor used for teaching and research, most recently for intrinsic and induced neutron noise studies. For future gamma detection applications in the CROCUS reactor, an array of four detectors - two large 5”x10” Bismuth Germanate (BGO) and two smaller Cerium Bromide (CeBr3) scintillators - was acquired. The BGO detectors are to be arbitrarily positioned in the core reflector and out of the vessel for measurements at arbitrary distances. The CeBr3 detectors on the other hand are small enough to be set in the guide tubes of the control rods for in-core measurements. We present a study of the neutron and gamma flux in the core and reflector using the MCNP 6.2 and Serpent 2 Monte Carlo codes for coupled neutron and photon transport criticality calculations. More specifically, we investigate and compare predicted spectra as well as reactivity worth of different envisioned experimental setups. We further predict pulse height spectra as well as doses to the crystals with and without cadmium shielding to estimate allowable reactor powers with respect to detector radiation hardness. The results serve as basis for calibration and aid in the design and regulatory approval of the experiments.

Commissioning and operation of the Cherenkov detector for proton Flux Measurement of the UA9 experiment

The UA9 Experiment at CERN-SPS investigates channeling processes in bent silicon crystals with the aim to manipulate hadron beams. Monitoring and characterization of channeled beams in the high energy accelerators environment ideally requires in-vacuum and radiation hard detectors. For this purpose the Cherenkov detector for proton Flux Measurement (CpFM) was designed and developed. It is based on thin fused silica bars in the beam pipe vacuum which intercept charged particles and generate Cherenkov light. The first version of the CpFM is installed since 2015 in the crystal-assisted collimation setup of the UA9 experiment. In this paper the procedures to make the detector operational and fully integrated in the UA9 setup are described. The most important standard operations of the detector are presented. They have been used to commission and characterize the detector, providing moreover the measurement of the integrated channeled beam profile and several functionality tests as the determination of the crystal bending angle. The calibration has been performed with Lead (Pb) and Xenon (Xe) beams and the results are applied to the flux measurement discussed here in detail.

Enhanced radiation hardness and signal recovery in thin diamond detectors

Using the advantage of the high spatial resolution of the Ruđer Bošković Institute (RBI) ion microprobe, small areas of a thin membrane single crystal chemical vapor deposition (scCVD) diamond detector were intentionally damaged with a high-intensity 26-MeV oxygen ion beam at various fluences, producing up to ∼1018 vacancies/cm3. The response of the detector was tested with the ion beam-induced charge technique (IBIC) using a 2-MeV proton beam as a probe. The signal amplitudes decreased down to approximately 50% of the original value at low electric fields (<10 V/μm) inside the detector. However, the increase of electric field to values of ∼100 V/μm completely recovers the signal amplitude. The results presented herein can facilitate the development of true radiation hard particle detectors.

Development of a picosecond MCP based particle detector

Abstract A time-of-flight detector based on microchannel plates (MCP) is under development. The main goal is the creation of a radiation hard large area detector providing ∼ 10 ps time resolution for single charged particle in strong magnetic field. Conceptually, the detector consists of Cherenkov radiator covered with semitransparent photocathode followed by a chevron pair of MCPs. The detector design and the status of the development are reported.

Cosmic matter in the laboratory - the Compressed Baryonic Matter experiment at FAIR

The Compressed Baryonic Matter (CBM) experiment will be one of the major scientific pillars of the future Facility for Antiproton and Ion Research (FAIR) in Darmstadt. The goal of the CBM research program is to explore the QCD phase diagram in the region of high baryon densities using high-energy nucleus-nucleus collisions. This includes the study of the equation-of-state of nuclear matter at neutron star core densities, and the search for the deconfinement and chiral phase transitions. The CBM detector is designed to measure rare diagnostic probes such as hadrons including multi-strange (anti-) hyperons, lepton pairs, and charmed particles with unprecedented precision and statistics. Most of these particles will be studied for the first time in the FAIR energy range. In order to achieve the required precision, the measurements will be performed at very high reaction rates of 1 to 10 MHz. This requires very fast and radiation-hard detectors, a novel data read-out and analysis concept based on free streaming front-end electronics, and a high-performance computing cluster for online event selection. The physics program and the status of the proposed CBM experiment will be discussed.

QCD Matter Physics at FAIR

The Compressed Baryonic Matter (CBM) experiment will be one of the major scientific pillars of the future Facility for Antiproton and Ion Research (FAIR) in Darmstadt. The goal of the CBM research program is to explore the QCD phase diagram in the region of high baryon densities using high-energy nucleus-nucleus collisions. This includes the study of the equation-of-state of nuclear matter at neutron star core densities, and the search for the deconfinement and chiral phase transitions. The CBM detector is designed to measure rare diagnostic probes such as hadrons including multi-strange (anti-) hyperons, lepton pairs, and charmed particles with unprecedented precision and statistics. Most of these particles will be studied for the first time in the FAIR energy range. In order to achieve the required precision, the measurements will be performed at very high reaction rates of 1 to 10 MHz. This requires very fast and radiation-hard detectors, a novel data read-out and analysis concept based on free streaming front-end electronics, and a high-performance computing cluster for online event selection. The status of FAIR and the physics program of the proposed CBM experiment will be discussed.

Conceptual design of MCP based particle detector

A time-of-flight detector based on microchannel plates (MCP) is under development. The main goal of this work is the creation of a radiation hard large area detector providing 10 ps time resolution in strong magnetic field. The conceptual detector design is described in details.

Silicon Carbide Radiation Detectors for Medical Applications

There is increasing interest in the development of radiation hard detector materials with the capability to discriminate within wide dose range and high radiation tolerance that are sensitive, and show a linear response. In this study, fabricated 4H-SiC Schottky diodes were exposed to dose rates ranging from 0.02 to 0.185 mGy/min to analyse the linearity and sensitivity at room temperature. High linearity response presented from the graph of current signal plotted versus dose rate which show enhancement of 104 in comparison to previous studies. The sensitivity measured at different bias voltages by exposing to 0.185 mGy/min dose rate show good reproducibility and stability of the current signal with time. Collected charge presented for all diodes exhibit linear behaviour of photon induced collected charge with the sensitivity between 1.40 to 8.38 x 105 nC/Gy for the 0.20 to 1 mGy absorbed dose range. Thus, these devices are ideally suited for the realisation of radiation detectors at moderate dose range.

Performance study for the photon measurements of the upgraded LHCf calorimeters with Gd2SiO5 (GSO) scintillators

The Large Hadron Collider forward (LHCf) experiment was motivated to understand the hadronic interaction processes relevant to cosmic-ray air shower development. We have developed radiation-hard detectors with the use of Gd2SiO5 (GSO) scintillators for proton-proton √s = 13 TeV collisions. Calibration of such detectors for photon measurement has been completed at the CERN SPS T2-H4 line in 2015 using electron beams of 100–250 GeV and muon beams of 150–250 GeV . After the channel-by-channel absolute energy calibration, the energy resolution of the calorimeters is confirmed to be better than 3% for electrons with energy above 100 GeV . The position dependence of the energy scale of the calorimeters was reduced to the level of 1% after the corrections for scintillator nonuniformity and the shower leakage effect. The position resolution of the new shower imaging detector, a GSO-bar hodoscope interleaved in the calorimeter, was 100 μm for 200 GeV electrons. The experimental results are well explained by Monte Carlo simulations. We have confirmed that the new detectors meet the requirement of the LHCf experiment at √s = 13 TeV.

Beam test results of STS prototype modules for the future accelerator experiments FAIR/CBM and NICA/MPD projects

High-energy heavy-ion collision experiments provide the unique possibility to create and investigate extreme states of strongly-interacted matter and address the fundamental aspects of QCD. The experimental investigation the QCD phase diagram would be a major breakthrough in our understanding of the properties of nuclear matter. The reconstruction of the charged particles created in the nuclear collisions, including the determination of their momenta, is the central detection task in high-energy heavy-ion experiments. It is taken up by the Silicon Tracking System in CBM@FAIR and by Inner Tracker in MPD@NICA currently under development. These experiments requires very fast and radiation hard detectors, a novel data read-out and analysis concept including free streaming front-end electronics. Thermal and beam tests of prototype detector modules for these tracking systems showed the stability of sensors and readout electronics operation.

The heavy-ion program of the future FAIR facility

The Compressed Baryonic Matter (CBM) experiment will be one of the major scientific pillars of the future Facility for Antiproton and Ion Research (FAIR) in Darmstadt. The goal of the CBM research program is to explore the QCD phase diagram in the region of high baryon densities using high-energy nucleus-nucleus collisions. This includes the study of the equation-of-state of nuclear matter at neutron star core densities, and the search for the deconfinement and chiral phase transitions. The CBM detector is designed to measure rare diagnostic probes such as hadrons including multi-strange (anti-) hyperons, lepton pairs, and charmed particles with unprecedented precision and statistics. Most of these particles will be studied for the first time in the FAIR energy range. In order to achieve the required precision, the measurements will be performed at very high reaction rates of 1 to 10 MHz. This requires very fast and radiation-hard detectors, a novel data read-out and analysis concept based on free streaming front-end electronics, and a high-performance computing cluster for online event selection. The physics program and the status of the proposed CBM experiment will be discussed.

New 3D Silicon detectors for dosimetry in Microbeam Radiation Therapy

Microbeam Radiation Therapy (MRT) involves the use of a spatially fractionated beam of synchrotron generated X-rays to treat tumours. MRT treatment is delivered via an array of high dose ‘peaks’ separated by low dose ‘valleys’. A good Peak to Valley Dose Ratio (PVDR) is an important indicator of successful treatment outcomes. MRT dosimetry requires a radiation hard detector with high spatial resolution, large dynamic range, which is ideally real-time and tissue equivalent. We have developed a Silicon Strip Detector (SSD) and very recently, a new 3D MESA SSD to meet the very stringent requirements of MRT dosimetry. We have compared these detectors through the characterisation of the MRT radiation field at the Australian Synchrotron Imaging and Medical Beamline. The EPI SSD was able to measure the microbeam profiles and PVDRs, however the effective spatial resolution was limited by the detector alignment options available at the time. The geometry of the new 3D MESA SSD is less sensitive to this alignment restriction was able to measure the microbeam profiles within 2 μm of that expected. The 3D MESA SSD measured PVDRs were possibly affected by undesired and slow charge collection outside the sensitive volume and additional scattering from the device substrate.

Soft X-ray tomography in support of impurity control in tokamaks

This contribution reviews an important example of current developments in diagnostic systems and data analysis tools aimed at improved understanding and control of transport processes in magnetically confined high temperature plasmas. The choice of tungsten for the plasma facing components of ITER and probably also DEMO means that impurity control in fusion plasmas is now a crucial challenge. Soft X-ray (SXR) diagnostic systems serve as a key sensor for experimental studies of plasma impurity transport with a clear prospective of its control via actuators based mainly on plasma heating systems. The SXR diagnostic systems typically feature high temporal resolution but limited spatial resolution due to access restrictions. In order to reconstruct the spatial distribution of the SXR radiation from line integrated measurements, appropriate tomographic methods have been developed and validated, while novel numerical methods relevant for real-time control have been proposed. Furthermore, in order to identify the main contributors to the SXR plasma radiation, at least partial control over the spectral sensitivity range of the detectors would be beneficial, which motivates for developments of novel SXR diagnostic methods. Last, but not least, semiconductor photosensitive elements cannot survive in harsh conditions of future fusion reactors due to radiation damage, which calls for development of radiation hard SXR detectors. Present research in this field is exemplified on recent results from tokamaks COMPASS, TORE SUPRA and the Joint European Torus JET. Further planning is outlined.

Development of high temperature, radiation hard detectors based on diamond

Single crystal CVD diamond has many desirable properties compared to current, well developed, detector materials; exceptional radiation, chemical and physical hardness, chemical inertness, low Z (close to human tissue, good for dosimetry), wide bandgap and an intrinsic pathway to fast neutron detection through the 12C(n,α)9Be reaction. However effective exploitation of these properties requires development of a suitable metallisation scheme to give stable contacts for high temperature applications. To best utilise available processing techniques to optimise sensor response through geometry and conversion media configurations, a reliable model is required. This must assess the performance in terms of spectral response and overall efficiency as a function of detector and converter geometry. The same is also required for proper interpretation of experimental data. Sensors have been fabricated with varying metallisation schemes indented to permit high temperature operation; Present test results indicate that viable fabrication schemes for high temperature contacts have been developed and present modelling results, supported by preliminary data from partners indicate simulations provide a useful representation of response.

Time-of-flight MeV-SIMS with beam induced secondary electron trigger

A new Time-of-flight MeV Secondary Ion Mass Spectrometry (MeV-SIMS) setup was developed to be used with a capillary microprobe for molecular imaging with heavy primary ions at MeV energies. Due to the low output current of the ion collimating capillary a Time-of-flight (ToF) measurement method with high duty cycle is necessary. Secondary electrons from the sample surface and transmitted ions were studied as start signals. They enable measurements with a continuous primary beam and unpulsed ToF spectrometer. Tests with various primary ion beams and sample types have shown that a secondary electron signal is obtained from 30% to 40% of incident MeV particles. This provides a ToF start signal with considerably better time resolution than the one obtained from transmitted primary ions detected in a radiation hard gas ionization detector. Beam induced secondary electrons therefore allow for MeV-SIMS measurements with reasonable mass resolution at primary ion beam currents in the low fA range.

RD50 Collaboration overview: Development of new radiation hard detectors

Silicon sensors are widely used as tracking detectors in high energy physics experiments. This results in several specific requirements like radiation hardness and granularity. Therefore research for highly performing silicon detectors is required. The RD50 Collaboration is a CERN R&D collaboration dedicated to the development of radiation hard silicon devices for application in high luminosity collider experiments. Extensive research is ongoing in different fields since 2001. The collaboration investigates both defect and material characterization, detector characterization, the development of new structures and full detector systems. The report gives selected results of the collaboration and places an emphasis on the development of new structures, namely 3D devices, CMOS sensors in HV technology and low gain avalanche detectors.

The OverMOS project

The OverMOS project aims to create a fast radiation hard tracking detector sensor, based on High Resistivity CMOS technology. In a first prototype submission, different pixel and charge collection node geometries have been produced, which have lately been returned from fabrication and are currently under test.

Carrier decay and luminescence characteristics in hadron irradiated MOCVD GaN

Crystalline GaN is a promising material for producing of the radiation hard particle detectors of different types capable to operate in harsh areas of particle accelerators. Moreover, GaN crystals show rather efficient luminescence properties in several spectral bands under excitation by high energy radiation. Thereby, GaN material can be employed for fabrication of a combined device which is able to operate both as scintillating and charge collecting detector. However, the efficiency of such detectors and their functionality has insufficiently been investigated. This work is addressed to study the evolution of the efficiency of photon and hadron induced luminescence. To evaluate the density of excess carriers induced by the high energy protons, a correlation between the microwave probed photoconductivity transients and the proton induced luminescence intensity has been examined using 1.6 MeV protons to produce a nearly homogeneous and rather strong excitation in 2.6 μm thick MOCVD grown GaN epi-layers. To estimate the radiation hardness of such material, the evolution of the photoconductivity transients and of the proton induced photoluminescence characteristics has been studied by in situ measurements of the changes of luminescence intensity and photoconductivity decay rate during the exposure to a proton beam reaching fluences up to 1015 cm-2. The production rate of radiation defects, determined from in situ and post-irradiation examination of the changes of radiative and non-radiative recombination have been examined by combining penetrative hadron (nuclear reactor neutrons and 24 GeV/c protons) irradiations with those of the 1.6 MeV protons. The parameters of the efficiency κP of carrier pair generation by asingle proton of κP = nP/NP ≅ 1.3 × 107 cm-3 per proton and κPApr = 40 carrier pairs per a micrometer of layer depth per proton have been estimated. The production rate of radiation defects is estimated to be KP ≅ 0.6 cm-1 for both penetrative neutrons and for 24 GeV/c protons. The hadronirradiation determines both the creation of the specific radiation defects with rate of KP ≅ 0.6 cm-1 and the modification of the material structure by increasing its disorder. Increase of disorder has been deduced from the observed decrease of value of the stretched-exponent index.

Quadruple Well CMOS MAPS With Time-Invariant Processor Exposed to Ionizing Radiation and Neutrons

Monolithic active pixel sensors featuring a time-invariant front-end channel have been fabricated in a quadruple well CMOS process in the frame of an R&D project aiming at developing low material budget, radiation hard detectors for tracking applications. MAPS prototypes have been exposed to integrated fluences up to 10 <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">14</sup> 1 MeV neutron equivalent cm to test the device tolerance to bulk damage also for different values of the epitaxial layer resistivity. Moreover, samples of the same device have been irradiated with y-rays from a <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">60</sup> Co source, reaching a final dose exceeding 10 Mrad, to study ionizing radiation effects. This work discusses the test results, obtained through different measurement techniques, and the mechanisms underlying performance degradation in irradiated quadruple well CMOS MAPS.

GaAs detectors irradiated by low doses of electrons

Semi-insulating (SI) GaAs detectors were irradiated by 5 MeV electrons up to a dose of 69 kGy, in order to test their radiationhardness. The electric and spectrometric stability of detectors was examinedas a function of the absorbed dose. Investigated detectors showed a verygood detector radiation resistance within a dose up to 40 kGy followed bydeterioration of some spectrometric and electric properties. However, thereverse current and the detector charge collection efficiency showed minimumchanges with the overall applied doses. The obtained results will be used asa preliminary study for further radiation-hardness investigations of GaAsdetectors against high energy electrons. This will complete our previousstudies of GaAs detector radiation hardness against fast neutrons andγ-rays.