Decrease In Rate Research Articles

Numerical study on dust particle charging and dynamics in continuous and pulsed radio frequency argon discharges

AbstractCharging and dynamics of a spherical dust grain injected into a continuous and pulsed radio frequency (RF) discharge have been studied using a one‐dimensional fluid model. First, the plasma characteristics of the two types of discharges are computed and compared. In the pulsed discharge, it is found that the central electron density exhibits a periodic variation while the averaged electron density is lower compared to that in the continuous discharge due to the decrease in the total ionization rate. Further, the dust charge is computed using the plasma characteristics. It is found that the dust charge negatively increases as the duty cycle ratio increases. Also, the charge in the pulsed discharge is lower in comparison to the continuous discharge due to the shorter duration of the pulsed RF discharge limiting the amount of energy transferred to electrons. On the other hand, the dust particle remains in the powered sheath region exhibiting a damped oscillation in the two discharges with higher oscillation frequency in the continuous discharge.

Monitoring and Quantifying Soil Erosion and Sedimentation Rates in Centimeter Accuracy Using UAV-Photogrammetry, GNSS, and t-LiDAR in a Post-Fire Setting

Remote sensing techniques, namely Unmanned Aerial Vehicle (UAV) photogrammetry and t-LiDAR (terrestrial Light Detection and Ranging), two well-established techniques, were applied for seven years in a mountainous Mediterranean catchment in Greece (Ilioupoli test site, Athens), following a wildfire event in 2015. The goal was to monitor and quantify soil erosion and sedimentation rates with cm accuracy. As the frequency of wildfires in the Mediterranean has increased, this study aims to present a methodological approach for monitoring and quantifying soil erosion and sedimentation rates in post-fire conditions, through high spatial resolution field measurements acquired using a UAV survey and a t-LiDAR (or TLS—Terrestrial Laser Scanning), in combination with georadar profiles (Ground Penetration Radar—GPR) and GNSS. This test site revealed that 40 m3 of sediment was deposited following the first intense autumn rainfall events, a value that was decreased by 50% over the next six months (20 m3). The UAV–SfM technique revealed only 2 m3 of sediment deposition during the 2018–2019 analysis, highlighting the decrease in soil erosion rates three years after the wildfire event. In the following years (2017–2021), erosion and sedimentation decreased further, confirming the theoretical pattern, whereas sedimentation over the first year after the fire was very high and then sharply lessened as vegetation regenerated. The methodology proposed in this research can serve as a valuable guide for achieving high-precision sediment yield deposition measurements based on a detailed analysis of 3D modeling and a point cloud comparison, specifically leveraging the dense data collection facilitated by UAV–SfM and TLS technology. The resulting point clouds effectively replicate the fine details of the topsoil microtopography within the upland dam basin, as highlighted by the profile analysis. Overall, this research clearly demonstrates that after monitoring the upland area in post-fire conditions, the UAV–SfM method and LiDAR cm-scale data offer a realistic assessment of the retention dam’s life expectancy and management planning. These observations are especially crucial for assessing the impacts in the wildfire-affected areas, the implementation of mitigation strategies, and the construction and maintenance of retention dams.

Quantifying denudation rates and sediment recycling of low-relief, high-elevation landscapes using in-situ and meteoric cosmogenic nuclides

Quantifying Earth’s surface denudation rates is crucial for estimating sediment flux and its role in regulating global climate change. The inability of in-situ cosmogenic 10Bein to quantify denudation rates in quartz–free environment has prompted the need for a new proxy–the ratio of meteoric 10Bemet to mineral-weathered 9Be in reactive phase (precipitated in or adsorbed onto secondary minerals). This study utilized 10Bein–26Alin, 10Bemet/9Be, and major element analyses of reactive and mineral phases of bedload sediments to infer basin-wide denudation rates and sediment recycling (reworking of deeply buried sediments) in the Three River Source Region (TRSR) of the central Tibetan Plateau. Results from 10Bein-26Alin analysis of bedload sediments and bedrock samples (quartz grain, 250–500 μm) suggest that the sediments underwent burial events since at least 0.54 ± 0.16 million years ago. Combining paleoclimate records in the central Tibetan Plateau, we interpret the “Great Burial” as most likely the result of climate-controlled deglaciation and denudation at the termination of Naynayxungla glaciation during the MIS 13–15 period. This event marks the first widespread deglaciation on the Tibetan Plateau. The 10Bein-26Alin derived paleo–denudation rates range from 4.2-0.8+0.9 to 151-32+37 mm/kyr, consistent with previous 10Bein–derived modern denudation rates of 10–117 mm/kyr in TRSR. These rates show a moderate positive correlation with regional topography, particularly channel steepness, indicating a decrease in both relief and denudation rates from lower to upper streams. This spatial discrepancy is likely due to enhanced river headward incision and active neotectonic activities in the southeast. Denudation rates derived from the 10Bemet/9Be proxy range from 13 to 248 mm/kyr, alongside a chemical weathering intensity ranging from 43 % to 67 %. These denudation rates are strongly correlated with, but about 1.5 times higher than, the 10Bein–26Alin derived paleo–denudation rates from the same watershed. This suggests that the 10Bemet/9Be extracted from fine grains (<64 μm) may reflect a different sediment recycling pattern compared to 10Bein–26Alin in quartz sediments. Alternatively, the 10Bemet/9Be ratio could indicate a mixture of carbonate rock with a high denudation rate and silicate rock with a lower denudation rate, whereas 10Bein–26Alin reflects a single silicate denudation signal.

Decrease in Rates of Hearing Loss From Pediatric Bacterial Meningitis Over Time: A Database Review.

Bacterial meningitis is a leading cause of acquired sensorineural hearing loss (SNHL). Treatment and prevention of bacterial meningitis have improved over time, but rates of neurologic complications have not been recently studied. The objective here is to present an updated population-based review of hearing loss as a sequela of bacterial meningitis. A retrospective cohort study was conducted between 2010 and 2022 of children discharged with bacterial meningitis, using the Pediatric Health Information System's (PHIS) database. Rates of hearing loss and mortality were evaluated over time. A total of 6138 children with a primary diagnosis of bacterial meningitis were identified (3520 male [57.3%], mean age 5.8 months [2.0, 61.2]). Of these, 277 (4.51%) were diagnosed with hearing loss. Children with hearing loss were significantly older (23.6 vs. 5.3 months, p < 0.01), but differences in gender, race, or ethnicity had no association with hearing loss. Streptococcus pneumoniae, Hemophilus influenzae, and Neisseria meningiditis were associated with significantly higher rates of hearing loss than other etiologies (p < 0.01). Children with hearing loss had a higher rate of receiving dexamethasone than children without hearing loss. Overall mortality rate was 2.1%. Hearing loss and mortality demonstrated significant decreases over the study period. Hearing loss remains a common sequela of bacterial meningitis despite widespread uptake of vaccines for preventing S. pneumoniae, H. influenzae, and N. meningitidis. Dexamethasone was not associated with decreased rates of hearing loss in this cohort. From 2010 to 2022, there was a significant decrease in overall rates of mortality and hearing loss for children with bacterial meningitis. Level 3: retrospective case-control series Laryngoscope, 2024.

Effects of colchicine on the prevention of AF recurrence after atrial ablation: a systematic review and meta-analysis.

Catheter ablation has become a widely accepted treatment for atrial fibrillation, but early recurrences remain a challenge, often attributed to inflammatory responses triggered during the procedure. This systematic review and meta-analysis aimed to evaluate the effectiveness of colchicine in preventing short-term AF recurrence post-ablation. PubMed, Embase, and Cochrane Library were searched for studies comparing use of colchicine and placebo in patients after AF ablation. Outcomes included AF recurrence, GI side effects, and hospitalization. R program (version 4.3.2) was used for statistical analysis. Heterogeneity was assessed with I2 statistics. Five studies, including 1592 patients, were analyzed. Pooled results revealed no statistically significant decrease in AF recurrence (OR 0.74; 95% CI 0.48-1.12; p = 0.153) and pericarditis rates (OR 0.67; 95% CI 0.26-1.72; p = 0.403) with colchicine use. No significant difference in hospitalization rates was observed between colchicine and placebo groups (OR 1.00; 95% CI 0.63-1.59; p = 0.996). In addition, gastrointestinal side effects were notably higher in the colchicine group (OR 4.84; 95% CI 2.58-9.05; p < 0.001). Prophylactic use of colchicine after atrial ablation was not associated with a reduction in AF recurrence and pericarditis rates. In addition, there was no difference in the rate of all-cause hospitalization between the groups, and colchicine use was associated with gastrointestinal adverse events.

Utilizing the sublingual form of squalene in COVID-19 patients: a randomized clinical trial

In this study, the efficacy of sublingual squalene in decreasing the mortality rate among patients with COVID-19 was investigated. Squalene was extracted from pumpkin seed oil with a novel method. Then, the microemulsion form of squalene was prepared for sublingual usage. In the clinical study, among 850 admitted patients, 602 eligible COVID-19 patients were divided in two groups of control (N = 301) and cases (N = 301) between Nov 2021 and Jan 2022. Groups were statistically the same in terms of age, sex, BMI, lymphocyte count on 1st admission day, hypertension, chronic kidney disease, chronic respiratory disease, immunosuppressive disease, and required standard treatments. The treatment group received five drops of sublingual squalene every 4 h for 5 days plus standard treatment, while the control group received only standard treatment. Patients were followed up for 30 days after discharge from the hospital. The sublingual form of squalene in the microemulsion form was associated with a significant decrease in the mortality rate (p < 0.001), in which 285 (94.7%) cases were alive after one month while 245 (81.4%) controls were alive after 1 month of discharge from the hospital. In addition, squalene appears to be effective in preventing re-hospitalization due to COVID-19 (p < 0.001), with 141 of controls (46.8%) versus 58 cases (19.3%). This study suggests sublingual squalene in the microemulsion as an effective drug for reducing mortality and re-hospitalization rates in COVID-19 patients.Trial Registration Number: IRCT20200927048848N3.

Effects of Simulated Acid Rain on Photosynthesis in Pinus massoniana and Cunninghamia lanceolata in Terms of Prompt Fluorescence, Delayed Fluorescence, and Modulated Reflection at 820 nm.

The effects of simulated acid rain (SAR) on the photosynthetic performance of subtropical coniferous species have not been thoroughly investigated. In this study, we treated two coniferous species, Pinus massoniana (PM) and Cunninghamia lanceolata (CL), with four gradients of SAR and then analyzed their photosynthetic activities through measurements of gas exchange, prompt fluorescence (PF), delayed fluorescence (DF), and modulated reflection at 820 nm (MR820). Gas exchange analysis indicated that the decrease in the net photosynthetic rate (Pn) in PM and CL was unrelated to stomatal factors. For the PF transients, SAR induced positive K-band and L-band, a significant reduction in photosynthetic performance index (PIABS), the quantum yield of electron transfer per unit cross-section (ETO/CSm), and maximal photochemical efficiency of photosystem II (Fv/Fm). Analysis of the MR820 kinetics showed that the re-reduction kinetics of PSI reaction center (P700+) and plastocyanin (PC+) became slower and occurred at later times under SAR treatment. For the DF signals, a decrease in the amplitude of the DF induction curve reduced the maximum value of DF (I1). These results suggested that SAR obstructed photosystem II (PSII) donor-side and acceptor-side electron transfer capacity, impaired the connectivity between PSII and PSI, and destroyed the oxygen-evolving complex (OEC). However, PM was better able to withstand SAR stress than CL, likely because of the activation of a protective mechanism.

An Evaluation of the Relationship between Membrane Properties and the Fouling Mechanism Based on a Blocking Filtration Model

Microfiltration plays an increasingly important role in various fields. Consequently, elucidating the mechanism of membrane fouling has emerged as a pivotal issue that needs to be resolved. In this study, a blocking filtration model was employed to evaluate the effects of membrane properties on the fouling mechanism during the microfiltration of representative polysaccharides, namely sodium alginate, pectin, and xanthan gum. Microfiltration membranes composed of hydrophilic and hydrophobic PVDF, mixed cellulose ester, as well as hydrophilic and hydrophobic PTFE were used as filter media. The flux decline behavior was significantly affected by the membrane properties, with hydrophilic membranes exhibiting a slower decrease in filtration rate. The model analysis revealed a correlation between the blocking characteristic values and the membrane properties. Although the blocking index n showed membrane material dependence, the values of this parameter remained consistent across various filtration conditions, including the wettability of the membrane surface, solute concentration, and pressure (pectin: n = 1.86, 1.85, 1.50, and 1.50 for hydrophilic PVDF, hydrophobic PVDF, hydrophilic PTFE, and hydrophobic PTFE, respectively). The resistance coefficient k was influenced by the characteristics of the membrane surface; the k values of the hydrophobic membranes were higher than those of the hydrophilic ones (pectin: k = 0.00084, 0.00725, 0.00714, and 0.0384 s1−n/cm2−n for hydrophilic PVDF, hydrophobic PVDF, hydrophilic PTFE, and hydrophobic PTFE, respectively). The model calculations, based on the values of n and k, demonstrated a relatively good agreement with the experimental data.

Interface design of carbon fiber composites by fabricating interlocked carbon nanotubes-silicon nitride nanowires

Prominent interfacial bonding can significantly improve the stress transfer efficiency between carbon fibers and matrix, which is the basis of efficient and long-term application of composites. In this paper, a bicomponent collaborative strategy was proposed to fully utilize the advantages of silicon nitride nanowires (SNs) and carbon nanotubes (CNTs) to optimize the interfacial strength of carbon fiber modified double matrix composites (CD), in which the double matrix was represented by polymers-hydroxyapatite and pyrocarbon-hydroxyapatite. The microstructure displayed that SNs were randomly distributed inside CD and completely wrapped by CNTs, which combined to form an interlocking structure. The mechanical and friction behavior of modified and unmodified composites was investigated. The compression strength and shear strength of CNTs-SNs modified carbon fiber/polymers-hydroxyapatite composites were 110 ± 2.39 MPa and 56 ± 1.13 MPa, displaying an increment of 69% and 87%. The wear rate was 0.4 × 10−14 ± 0.008 m3 N−1 m−1, exhibiting a 61% decline. The fracture morphologies were observed to analyze the strengthening mechanism. Interlocked CNTs-SNs could strengthen the effective bonding of fiber/matrix interface and SNs/matrix interface, provide lots of nucleation sites for the matrix, and enhance the matrix cohesion. The enhancement was further verified by a 56% increase in the compression strength (237 ± 4.67 MPa), a 235% increase in the shear strength (77 ± 1.53 MPa), a 78% decrease in wear rate (0.38 × 10−13 ± 0.011 m3 N−1 m−1) of CNTs-SNs modified carbon fiber/pyrocarbon-hydroxyapatite composites, indicating that CNTs-SNs played an indispensable role in making CD possess brilliant mechanical and biological friction properties.

Thermochemical energy storage analysis of solar driven carbon dioxide reforming of methane in SiC-foam cavity reactor

Solar energy is an abundant renewable energy source, and the use of solar energy for carbon dioxide reforming of methane (CRM) is a promising thermochemical energy storage scheme, but the reactor using the traditional powder catalyst has the disadvantages of complex encapsulation and low energy storage efficiency. In this paper, porous SiC-foam with high thermal conductivity is used to prepare Ni/CeO2–Al2O3/SiC catalyst, and then is loaded into a cavity reactor to achieve highly efficient and stable CRM under solar simulator. After a period of reaction, methane conversion rate remains high. As inlet flow rate decreases and incident energy flux rises, methane conversion rate is improved, and thermochemical energy storage efficiency first rises and then drops with maximum 31.4%. The numerical model of the cavity reactor under concentrated heat flux is established, and the simulation results are in good agreement with the experimental data. The structure of catalyst bed directly influences the heat storage performance, and the optimal bed thickness, radius and porosity are obtained. For thick bed, the reverse reaction appears in the end region of the bed, and then this region expands with bed thickness rising, so the reaction rate first increases and then decreases.

Grain growth behavior in TaC-modified ultrafine Ti(C, N)-based cermets

Revealing the grain growth behavior during liquid phase sintering is of great significance for scientific application of grain growth inhibition strategies and the regulation of microstructure. In this study, the effects of both TaC addition and the particle size of starting materials on microstructure of Ti(C, N)-based cermets were investigated. Ultrafine Ti(C, N)-based cermets modified with TaC addition exhibit an obvious grain growth of grey phase during liquid phase sintering. The grain growth of grey phase is typically controlled by liquid-phase diffusion, with the grain growth index of 3 and activation energy of 48–66 kJ/mol. In particular, the increase in grain contiguity of grey phase caused by the evaporation of metal liquid phase at high temperatures, faceted transition of grey phase grains, and the loss of carbon and nitrogen are considered to be the main reasons for the decrease in the grain growth rate of grey phase at high temperatures.

Conformational Isomerization Effect on Singlet/Triplet Energy Consumption Process of Thermally Activated Delayed Fluorescence Molecules with Aggregation Induced Emission: A QM/MM Study.

Thermally activated delayed fluorescence (TADF) molecules with aggregation-induced emission (AIE) properties hold tremendous potential in biomedical sensing/imaging and telecommunications. In this study, a multiscale method combined with thermal vibration correlation function (TVCF) theory is used to investigate the photophysical properties of the novel TADF molecule CNPy-SPAC in toluene and crystal and amorphous states. In the crystal state, an increase in radiative rates and a decrease in nonradiative rates lead to AIE. Additionally, conformational isomerization effects result in significantly different luminescent efficiencies between the two crystal structures. Furthermore, the isomerization effect allows for the coexistence of three configurations in the amorphous state. Among them, the non-TADF quasi-axial (Qa) configuration may facilitate energy transfer to the TADF-characteristic quasi-equal/quasi-equal-H (Qe/Qe-H) configurations, enhancing AIE. Moreover, the Qa configuration enables rapid electron transport, offering the potential for self-doped devices. Our work elucidates a new mechanism for the isomerization effect in AIE-TADF molecules.

Гуанідінійвмісний олігомер як інгібітор мікробної корозії металу

Guanidinium-containing oligomers, a poorly studied class of organic compounds, have attracted attention due to their bactericidal properties. A guanidinium-containing oligomer based on an aliphatic oligoepoxide is a newly synthesized substance with bactericidal activity, which gives it the prospects for use as a microbial corrosion inhibitor. Aim. The goal of the study was to synthesize oligomeric alkyl substituted guanidinium bromide and study of its anticorrosive properties in the presence of steel under the influence of corrosive active sulfate-reducing bacteria. Methods. The guanidine-containing alkyl substituted oligomer was obtained by the reaction of the aliphatic oligoepoxide DEG-1 with guanidine, followed by interaction with alkyl bromide. The anticorrosive properties of the guanidine-containing oligomer were studied using collection strains of sulfate-reducing bacteria: UCM B-11503 Desulfovibrio sp.10, UCM B-11501 Desulfovibrio desulfuricans DSM642, and UCM B-11502 Desulfovibrio vulgaris DSM644. The sulfate-reducing bacteria were grown on Postgate В medium for 14 days at a temperature of 28 ± 2 °C. The number of bacteria was determined by the method of tenfold dilution. The corrosion rate was determined by the gravimetric method. The physicochemical parameters of pH and redox potential of the bacterial culture liquid were studied by the potentiometric method. The accumulation of hydrogen sulfide in the culture liquid was determined by the iodometric method. Lipolytic activity was studied spectrophotometrically using a KFK-3 device by reaction with p-nitrophenyl palmitate, catalase activity — using 0.03% hydrogen peroxide, which formed a stable colored complex with a 4% molybdenum diphosphate solution. The specific activity of the studied enzymes was expressed as unit ∙ mg-1 protein. Protein was determined in the supernatant by the conventional Lowry method. Results. It was shown that the oligomer based on aliphatic oligoepoxide has biocidal properties. A significant inhibition of the development of sulfate-reducing bacteria (SRB) was observed after the oligomer was added; only dozens of bacterial cells were detected in the medium after the exposure period. The corrosion rate of steel in the presence of SBR without addition of inhibitors was 0.15 — 0.35 mg/cm2∙h. The addition of DPC (a quaternary ammonium compound based on N-decylpyridinium chloride) (Kyiv Polytechnic Institute (KPI), Ukraine) to the culture medium led to a decrease in the steel corrosion rate to 0.032 — 0.047 mg ∙ cm-2 h-1 (by 6.5—10.6 times). In the presence of Armohib CI-28 inhibitor (based on Diamine Ethoxylate) (Akzonobel, Holland), the corrosion rate was reduced to 0.02—0.039 mg ∙ cm-2 h-1 (by 4.2 — 12.7 times). The addition of guanidinium-containing oligomer to the medium with bacteria reduced the corrosion rate to 0.075—0.079 mg/cm2 ∙ h (by 2.5—2.7 times). According to the mass loss of steel samples, the degree of metal protection against microbial corrosion in the presence of guanidinium-containing oligomer was 60.15—63.17%. Conclusions. The obtained data indicate that the guanidinium-containing oligomer based on aliphatic oligoepoxy has biocidal and anticorrosive properties and is promising for use as a means of combating microbially induced corrosion.

Molecular hydrogen attenuates sepsis-induced cardiomyopathy in mice by promoting autophagy

BackgroundApproximately 40 to 60% of patients with sepsis develop sepsis-induced cardiomyopathy (SIC), which is associated with a substantial increase in mortality. We have found that molecular hydrogen (H2) inhalation improved the survival rate and cardiac injury in septic mice. However, the mechanism remains unclear. This study aimed to explore the regulatory mechanism by which hydrogen modulates autophagy and its role in hydrogen protection of SIC.MethodsCecal ligation and puncture (CLP) was used to induce sepsis in adult C57BL/6J male mice. The mice were randomly divided into 4 groups: Sham, Sham + 2% hydrogen inhalation (H2), CLP, and CLP + H2 group. The 7-day survival rate was recorded. Myocardial pathological scores were calculated. Myocardial troponin I (cTnI) levels in serum were detected, and the levels of autophagy- and mitophagy-related proteins in myocardial tissue were measured. Another four groups of mice were also studied: CLP, CLP + Bafilomycin A1 (BafA1), CLP + H2, and CLP + H2 + BafA1 group. Mice in the BafA1 group received an intraperitoneal injection of the autophagy inhibitor BafA1 1 mg/kg 1 h after operation. The detection indicators remained the same as before.ResultsThe survival rate of septic mice treated with H2 was significantly improved, myocardial tissue inflammation was improved, serum cTnI level was decreased, autophagy flux was increased, and mitophagy protein content was decreased (P < 0.05). Compared to the CLP + H2 group, the CLP + H2 + BafA1 group showed a decrease in autophagy level and 7-day survival rate, an increase in myocardial tissue injury and cTnI level, which reversed the protective effect of hydrogen (P < 0.05).ConclusionHydrogen exerts protective effect against SIC, which may be achieved through the promotion of autophagy and mitophagy.

The complex stress of waterlogging and high temperature accelerated maize leaf senescence and decreased photosynthetic performance at different growth stages

AbstractThe greenhouse effect caused by global warming was becoming more and more obvious, resulting in increased frequency of high temperature and high humidity, which significantly affected maize productivity. However, it was poorly understood how the interactions of high temperature and high humidity affected leaf senescence, photosynthetic performance and yield of summer maize. Three stress treatments including (a) high temperature stress (T), (b) waterlogging stress (W) and (c) complex stress (T‐W) were set at the third leaf stage (V3), the sixth leaf stage (V6) and the tasselling stage (VT) in 2019–2020 to explore the influence mechanism of complex stress. Each stress treatment period lasted 6 days. Non‐stressed plants served as control. Yield, antioxidant enzyme activity, photosynthetic characteristics, and dry matter accumulation were determined. Our study found that the activity of antioxidant enzymes was significantly decreased, while malonyldialdehyde (MDA) accumulation was increased under each stress treatment. As a result, the photosynthetic characteristics were impaired, manifested in a significant decrease in net photosynthetic rate (Pn), enzyme activities of phosphoenolpyruvate carboxylase (PEPCase) and ribulose diphosphate carboxylase (RUBPCase). The decrease in photosynthetic intensity affected by each stress treatment led to a significant decrease in total dry matter accumulation and grain yield. The most significant effects of waterlogging and combined stresses on yield occurred at the V3 stage, followed by the V6 and VT stages. However, the most significant effects of high temperature occurred at the VT stage, followed by the V6 and V3 stages. Moreover, the compound stress exacerbated damage to leaf senescence and photosynthetic properties of summer maize compared to the single stress of high temperature or waterlogging.

Mechanical characterization and water stability of loess improved by bio-based materials: An eco-friendly approach

Loess exhibits poor engineering properties, such as low strength and poor water stability. Conventional materials used for improving loess, such as cement and lime, result in environmental pollution issues throughout their production and application processes. To assess the efficacy of bio-based materials, including calcium alginate (CA), xanthan gum (XA), cotton fibers (CO) and flax fibers (FA) in the treatment of loess, the improved soil's strength, disintegration, and water resistance were examined. Subsequently, an optimal amendment approach was determined, and dry-wet cycle tests and microscopic observation were performed. The results show that 1.0 % calcium alginate can effectively enhance the strength of loess, significantly improving its resistance to disintegration with almost no observable disintegration; permeability is significantly reduced, and water repellency is enhanced. 2.0 % xanthan can improve the strength and disintegration resistance of loess, but the improvement in strength is lower than that of calcium alginate. Additionally, the improved soil with XA experiences a flocculent disintegration in static water, which cannot maintain the soil structure. Cotton fibers and flax fibers can enhance both compressive and tensile strength of the soil. The content of 0.45 % flax fibers is considered the optimal choice as it has no effect on water stability. Combining the above results, the combination of 1.0 % CA and 0.45 % FA has been selected to improve the loess, which effectively improves the comprehensive mechanical properties and water stability of the composite improved soil. The decrease in strength and mass loss rate are significantly reduced after dry-wet cycle tests. Microscopic tests show that calcium alginate connects soil particles by Ca2+ ionic bridges, which allows the cementing materials to fill the loess pores and exert the role of agglomeration and coagulation to enhance the integrity of the loess. This study shows that the bio-based material with calcium alginate as the main body can effectively improve the mechanical strength and water stability of the loess.

The Effect of the Stringent Response and Oxidative Stress Response on Fitness Costs of De Novo Acquisition of Antibiotic Resistance.

Resistance evolution during exposure to non-lethal levels of antibiotics is influenced by various stress responses of bacteria which are known to affect growth rate. Here, we aim to disentangle how the interplay between resistance development and associated fitness costs is affected by stress responses. We performed de novo resistance evolution of wild-type strains and single-gene knockout strains in stress response pathways using four different antibiotics. Throughout resistance development, the increase in minimum inhibitory concentration (MIC) is accompanied by a gradual decrease in growth rate, most pronounced in amoxicillin or kanamycin. By measuring biomass yield on glucose and whole-genome sequences at intermediate and final time points, we identified two patterns of how the stress responses affect the correlation between MIC and growth rate. First, single-gene knockout E. coli strains associated with reactive oxygen species (ROS) acquire resistance faster, and mutations related to antibiotic permeability and pumping out occur earlier. This increases the metabolic burden of resistant bacteria. Second, the ΔrelA knockout strain, which has reduced (p)ppGpp synthesis, is restricted in its stringent response, leading to diminished growth rates. The ROS-related mutagenesis and the stringent response increase metabolic burdens during resistance development, causing lower growth rates and higher fitness costs.

Evaluation of mechanical properties, heating rate and radio frequency explosive puffing (RFEP) quality of purple sweet potato under different moisture contents and moisture equilibrium process

The effects of different initial moisture contents (15–55%) and moisture equilibrium process (MEP) on the mechanical properties of the gas-blocking surface layer of purple sweet potato chips and the radio frequency (RF) heating rate, uniformity, and radio frequency explosion puffing (RFEP) quality were discussed in this article. Low-field nuclear magnetic resonance indicated that hot-air pre-drying reduced the amount of free water and caused the transfer of immovable water to bound water. This process was accompanied by an increase in the thickness and elastic modulus of the gas-blocking surface layer, resulting in a significant increase in the RF heating rate and uniformity. Prolonged RF heating time led to a decrease in anthocyanin content. The results demonstrated that the puffing rate initially increased and then decreased with increasing initial moisture content. The puffed sample with an initial moisture content of 45% exhibited the highest puffing rate, crispiness, and porosity. X-ray micro-tomography results reveal that MEP improved the morphology of puffed products, ensuring even distribution of small pores and reducing the presence of hard edges. In conclusion, considering the heating time and anthocyanin retention rate, the initial moisture content ranges from 35% to 45% after MEP was the best pre-treatment.

Effects of topological structure and destination selection strategies on agent dynamics in complex networks

We analyzed agent behavior in complex networks: Barabási–Albert, Erdos–Rényi, and Watts–Strogatz models under the following rules: agents (a) randomly select a destination among adjacent nodes; (b) exclude the most congested adjacent node as a potential destination and randomly select a destination among the remaining nodes; or (c) select the sparsest adjacent node as a destination. We focused on small complex networks with node degrees ranging from zero to a maximum of approximately 20 to study agent behavior in traffic and transportation networks. We measured the hunting rate, that is, the rate of change of agent amounts in each node per unit of time, and the imbalance of agent distribution among nodes. Our simulation study reveals that the topological structure of a network precisely determines agent distribution when agents perform full random walks; however, their destination selections alter the agent distribution. Notably, rule (c) makes hunting and imbalance rates significantly high compared with random walk cases (a) and (b), irrespective of network types, when the network has a high degree and high activity rate. Compared with the full random walk in (a) and (b) increases the hunting rate while decreasing the imbalance rate when activity is low; however, both increase when activity is high. These characteristics exhibit slight periodic undulations over time. Furthermore, our analysis shows that in the BA, ER, and WS network models, the hunting rate decreases and the imbalance rate increases when the system disconnects randomly selected nodes in simulations where agents follow rules (a)–(c) and the network has the ability to disconnect nodes within a certain time of all time steps. Our findings can be applied to various applications related to agent dynamics in complex networks.

Effect of UV Stress on the Antioxidant Capacity, Photosynthetic Activity, Flavonoid and Steviol Glycoside Accumulation of Stevia rebaudiana Bertoni

Lighting conditions are an important controller of plant growth and development, and they affect secondary metabolite synthesis. In this research, we explored the effect of additional UV irradiation of various ranges in addition to the main one at PPFD 160 µmol m−2 s−1 on the accumulation of some secondary metabolites of stevia (Stevia rebaudiana Bertoni). The fresh weight of leaves was slightly higher under additional UV-A and UV-B irradiation compared with the control variant, and the leaf surface area was significantly larger, respectively, by 23.3 and 20.7% than in the control variant, while the rate of photosynthesis did not decrease. Plants under additional UV-B and UV-C irradiation were under the greatest light stress, as evidenced by a decrease in antioxidant capacity by an average of 30% compared to the control and UV-A. The total flavonoid content was significantly higher (by 74%) under UV-B irradiation. The highest concentration of steviol glycoside was observed during budding and flowering under UV-B and UV-C irradiation (by 13.2 and 11.3%, respectively). Analysis of hyperspectral images, chlorophyll fluorescence, and vegetation indices showed light stress increasing under UV-C irradiation, which caused an increase in the relative chlorophyll content, scorches, leaf morphology changes, a CO2 absorption rate decrease, and plant growth inhibition. UV-B irradiation can be used as an optimal type of irradiation based on a set of indicators.