Conductivity Of Films Research Articles

Exploring cyclic olefin copolymer (COC) for flexible silver nanowire electrode

The development of flexible electronic devices has been a primary focus in various fields, and silver nanowire (Ag NW) networks show significant promise due to their unique electrical and mechanical properties. However, achieving well-defined and stable nanowire coatings on polymer substrates remains challenging. This work presents a novel and simple approach for directly coating Ag NWs on cyclic olefin copolymer (COC) substrates utilizing ultraviolet/ozone (UVO) treatment, a method not previously demonstrated for this specific material system up to our knowledge. The compatibility of this approach with COC eliminates the need for complex pre- and post-treatment processes, making it a more straightforward and environmentally friendly way to improve adhesion between Ag NWs and COC. The Ag NWs/COC electrodes exhibited excellent optoelectrical performance, with a high optical transmittance of 84% and a low sheet resistance of 13 Ω/sq—metrics that compare favorably to industry standards for transparent conductive films. Additionally, the Ag NWs/COC electrodes displayed excellent mechanical stability, showing no changes in sheet resistance after both tape adhesion and film bending tests. The novelty of the presented Ag NW-COC system, combined with the simplicity and environmental benefits of the UVO coating approach, as well as the demonstrated performance and stability of the resulting electrodes, make this work a significant advancement towards realizing the commercial potential of flexible electronics for biocompatible and wearable device applications.

Large-Area Perovskite Solar Modules Based on Uniformity Engineering of Perovskite Films: The Critical Role of Methyldiphenylphosphine Oxide Additive.

Perovskite solar cells (PSCs) have led to distinguished achievements and become one of the state-of-the-art photovoltaic technologies. Undoubtedly, reliable preparation of large area high-quality perovskite (PVK) films with uniform optoelectronic properties has become a critical and challenging task to transition PSCs from lab to market. Here, methyldiphenylphosphine oxide (MDPPO) is employed as an additive in a PVK precursor solution to promote uniform conductivity and carrier transport of PVK films. More important, to check its compatibility with the upscaling process, the MDPPO additive strategy was further applied to doctor-blade large-area PVK films. As a result, benefit from the favorable role of MDPPO additive, the power conversion efficiencies (PCEs) of small-area PSCs reach 23.85% with superb open circuit voltage (Voc) of 1.15 V and fill factor of 81.21%, while an impressive PCE of 19.22% was achieved for the large-area PSC minimodules with active area of 61.48 cm2. Remarkably, the MDPPO modified device exhibits significantly improved operational stability, maintaining an initial efficiency of 68% even after 750 h under continuous 1-sun illumination. Our achievements will provide profound insight and further guidance for the scale-up process of PSCs from lab to large-scale modules.

Multifunctional sensors for surface synchronized monitoring of Pressure/Biopotential signals and motion recognition

Surface biopotential dry electrodes are an important part of long-term healthcare health monitoring systems. During long-term dynamic monitoring, pressure fluctuations between the skin/electrode can affect the acquisition of ECG signals and reduce the stability of the system. In this study, by printing an interactive circuit on the back of the Fructus xanthii-inspired barb structure (FXbs) Ag/AgCl-TPU dry electrodes, the micro-nanocone PANI/PMMA flexible conductive film is encapsulated on the back of the FXbs dry electrode, and a multifunctional sensor and monitoring clothing are constructed, which can synchronously collect pressure signals and ECG signals, and can monitor human movements. In the simulation instrument and human skin surface, the influence of pressure fluctuation on the quality of ECG signal acquisition under different pressure, speed, and motion states is explored. In the simulation instrument, when the change rate of piezoresistive reaches the maximum value of 51.41 %, the fluctuation range of ECG is the smallest, which is 0.99 mV. On the surface of human skin, the change rate of piezoresistive and the fluctuation range of ECG in the turning state reach the maximum, which is 5.02 % and 5.99 mV, respectively. It can provide a reference to study the influence of pressure fluctuation on ECG signals on the surface of human skin, and at the same time, it can provide an experimental method and basis for the study of the dynamic noise mechanism at the electrode/electrolyte interface.

Anisotropic thermally conductive films based on two‐dimensional nanomaterials

AbstractThe significant advancement of high‐power densification and miniaturization in modern electronic devices has attracted increasing attention to effective thermal management. The primary objective of thermal management is to transfer excess heat from electronics to the outside environment through the use of thermal conductive materials. The anisotropic thermally conductive films (TCFs) based on two‐dimensional (2D) nanomaterials exhibit outstanding controlled heat transfer capability, which effectively removes hotspots along the in‐plane direction and provides thermal insulation along the cross‐plane direction. However, a comprehensive review of anisotropic TCFs is rarely reported. Herein, we first discuss the intrinsic anisotropic thermal conductivity of 2D nanomaterials for preparing TCFs. Then, the preparation methods and anisotropic thermal conductivity of TCFs have been summarized and discussed. Furthermore, we conclude with the practical applications of TCFs for anisotropy thermal management. Finally, a conclusion of the challenges and outlook of TCFs is provided to promote their development in future scientific research.

Dual ion regulation enables High-Coulombic-efficiency lithium metal batteries

Lithium (Li) metal batteries are ideal alternatives for pursuing high-energy-density batteries. Nevertheless, their subpar cycling capabilities and safety problems remain a significant concern because of the insufficient reversibility of Li plating/stripping processes. Herein, potassium trifluoromethanesulfonate (KOTf) is proposed as an electrolyte additive to achieve high Coulombic efficiency during cycling, which could be assigned to the synergistic regulation effect of anions and cations in KOTf. On the one hand, the OTf- helps form an anion-rich solvation structure, which could be preferentially reduced to obtain a robust and conductive inorganic-rich SEI film to stabilize the lithium metal anode. On the other hand, the existence of K+ induces the generation of K+-rich positive charge shielding layer, further hindering the growth of Li dendrite. The KOTf-assisted Li||Cu cell shows a high Coulombic efficiency (CE) of 99.7 % and an extremely long-cycle life of 700 cycles with an average CE of 99.01 % under 0.5 mA cm−2 and 0.5 mAh cm−2. The excellent lithium metal stripping/plating efficiency is mainly due to the OTf--derived inorganic-rich SEI and the electrostatic shielding effect of K+. This work emphasizes the important role of salts’ anions and cations in determining the CE of LMBs and provides an effective strategy to improve the cycling performance of LMBs.

Exploring the AC conductivity and dielectric properties of PVA films doped with Erythrosin B

Erythrosin B (EB) doped in PVA film was processed utilizing the casting procedure, and the structure was investigated via the Fourier Transformation infrared technique (FTIR). FTIR analysis presented a strong formation of intermolecular hydrogen bonds among PVA and EB hydroxyl groups (OH). Characteristic temperature and frequency variation of dielectric behavior and AC electrical conductivity for films of PVA doped with Erythrosin B were analyzed at (293–383 K) temperature and (102–106 Hz) frequency. The AC conductivity dependency indicates that the predominant conduction mechanism in PVA doped with Erythrosin B films follows the correlated barrier hopping (CBH) model. The charge carriers’ hopping involving localized states causes a relaxation process. Estimates were made for the AC conductivity activation energy and the conductivity relaxation energy. Frequency and temperature affect the dielectric constant (ε′) and the dielectric loss (ε″). The complex impedance spectrum (Z′ versus Z″) showed single semicircular arcs with a decreased radius with increasing temperature. The relaxation peaks in the electric modulus representation are clearly defined, and the relaxation period has been calculated.

Influence of a plasma focus device on the structural and optical properties of highly conductive AZO thin films

In the present work, we deposited Al-doped ZnO (AZO) thin films on microscope glass slides at different pressures (5, 10, 20, and 30 mTorr) using an EAEA-PFD (Plasma Focus Device of the Egyptian Atomic Energy Authority) without any extra heat treatment. Argon gas provided the radiant energy needed to form a crystalline AZO film. This study investigated the deposition and features of AZO thin films. The impact of changes in work pressure on the microstructure, morphology, and optical attributes of AZO films was reported. The results demonstrated that varying the work pressure significantly affects the microstructure, morphology, crystallinity, optical absorbance, and optical energy gap. The microstructure and morphology were evaluated through XRD and scanning electron microscopy (SEM). The optical properties were analyzed using a UVvis double-beam spectrophotometer within a wavelength range from 300 to 1100 nm. XRD patterns indicating a zinc-blende structure and the Williamson–Hall approach were used to estimate the structural parameters. The estimated trend in the particle size of the AZO film demonstrates a decrease from 82 ± 5 nm to 48 ± 5 nm as the pressure increases. The calculated energy gap, Egopt, increases from 3.53 eV to 3.69 eV with increasing work pressure. The conductivities in terms of both optical and electrical decreased with increasing work pressure of the AZO films.

Graphene and Vanadium Dioxide-Based Terahertz Absorber with Switchable Multifunctionality for Band Selection Applications.

This study proposes a multifunctional absorber in the terahertz (THz) regime based on vanadium dioxide (VO2) and graphene with either-or band selector applications, which can be realized by electrically and thermally controlling the Fermi energy level of graphene and vanadium dioxide, respectively. The broadband absorption can be achieved with absorptance exceeding 90%, when the VO2 film is in the metallic phase and the Fermi energy levels of the upper and lower graphene layers are simultaneously set to 0.6 and 0 eV, respectively. The double narrowband can be realized when the VO2 film is in the insulating phase and the Fermi energy levels in upper and lower graphene layers are set as 0 and 0.8 eV, respectively. By flexibly shifting between the broadband and the double narrowband, the proposed absorber can be used as an either-or band selector, corresponding optional bandwidth from 2.05 to 2.35 THz, and 3.25 to 3.6 THz. Furthermore, single narrowband absorption can be achieved by setting the conductivity of the VO2 film to appropriate values. The proposed absorber can be used in the THz regime in applications such as multifunctional devices, switches, cloaking objects, and band selectors.

Deposition characteristics and influence regularity of sputtered products in a low-power RF gridded ion thruster

RF ion thruster has a broad prospect of development via its simple structure, high specific impulse and electrode-less discharge. During the RF operating process, an important but ignored generally issue is that the high-energy metal particles generated by sputtering grid system can diffuse towards the ionization chamber and then deposit on the wall to form a conductive film. As a result, the RF power feed can be significantly inhibited which affects the thruster perform and reliability. In this work, the axial distribution of film thickness on the ionization chamber has been measured which has the characteristic of nonlinear distribution. And the film roughness can be significantly affected due to the gradient of film thickness and deposition temperature. Another corresponding measurement of plasma parameter evolutions in the ionization chamber has been carried out within 6000 min of thruster operation. Results shows that the presence of the deposited film can result in a ∼30 % decrease in the plasma density, which weakens the grid sputtering erosion and subsequently leads to a decrease in film growth rate. The combination of contributed to the degradation of the thruster performance, with the effect of deposited film accounting for about 41 %.

Confined CuⅠ sites in partially electro-reduced 2D conductive Cu-MOF film for boosting CO2 electrocatalysis to C2 products

Cu-based catalysts, especially co-sites of Cu0 and CuⅠ, are the best competitors for electrochemical CO2 fixation to produce multi-carbon (C2 + ) products. However, it is challenging to construct highly stable CuⅠ sites due to the changeability of its valence state and electronic structure in the electroreduction process, and the mechanism is also elusive. Herein, a 2D conductive CuⅡ-MOF film (CuⅡHHTP@Cu0) is prepared on Cu (100) foil by in-situ electrochemical assembly. After pre-reduction, the in-situ produced Cu2O clusters are confined in the cavities of the film created by the local breaking of the MOF framework to construct a unique CuⅠ-CuⅡHHTP@Cu0 catalyst, so that a novel strategy is proposed to stablize highly dispersed CuⅠ sites during electrochemical reduction, thus protecting the Cu2O clusters from further reduction and ensuring the coexistence of CuⅠ (111)-Cu0 (100) sites. As such, the current density of CO2 electrochemical reduction catalyzed by this catalyst exceeds 300 mA cm−2, the duration overs 50 h, and the C2 selectivity achieves 72.6 %. In-situ spectroscopy and theoretical calculations reveal that the optimized microenvironment of the CuⅠ (111) sites reduces the energy barrier of *OCCOH coupling, and Cu0 (100) sites increase the coverage of *CO, thus boosting the production of C2 products.

Fabrication and characterization of bacterial cellulose/carbon nanotube composite conductive film and its impact on the luminance of flexible electroluminescent devices as the bottom electrode

Flexible conductive films (BC/CNTs) were fabricated via a straightforward vacuum filtration method using bacterial cellulose (BC) as the substrate and single-walled carbon nanotubes (SWCNTs) as the conductive filler. The resulting BC/CNTs composite films were characterized for the morphology, structure, thermal properties and electrical conductivity using scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TG) and X-ray photoelectron spectroscopy (XPS). The study revealed that, the addition of SWCNTs significantly improved the mechanical properties of films. Among the BC/CNTs composite films, the one with the SWCNTs concentration of 0.36 wt% exhibited the best mechanical properties. Incorporating SWCNTs also enhanced the thermal stability and improved electrical conductivity of the composite films. Notably, higher SWCNTs concentrations led to better thermal stability and lower electrical resistance. Ultimately, these BC/CNTs composite films were successfully employed in flexible electroluminescent devices, demonstrating good luminescence.

Enhancement of electrical and photo-electrical properties of P3HT:CrCl2 thin films for photo sensing applications

In this work, doped and undoped P3HT thin films are prepared and deposited onto ITO interdigitated electrodes. To improve the optical and the electrical properties of the pure P3HT thin film, chromium(II) chloride was used as dopant material with three different weight percentage, 2.5%, 5%, 10%. Room-temperature current–voltage (I-V) characteristics of the samples were measured, showing an increase in the electrical current with increasing the dopant concentration. Under dark condition, the conductivity and resistivity of the pure P3HT thin films were enhanced by a factor of 5× as a result of doping the P3HT by 10 wt% of CrCl2. Under light intensity (50 mW cm−2) and at 10 V bias, the conductivity and resistivity obtained from P3HT:CrCl2 (10 wt%) thin films are 4.75 × 10−4 S cm−1 and ∼2 kΩ, respectively. These results exhibit an enhancement by a factor of ∼12× compared to those obtained from pure P3HT thin film. The current of the photo-sensors based on doped/undoped P3HT thin films are measured as a function of time under light intensity ranging from 0 to 50 mW cm−2 at 1 V bias, exhibiting high photo-response and good reproducibility. Three different wavelengths, white, green, and red were used as light sources to expose the photo-sensors. Under white light, photo-sensor based on P3HT:CrCl2(10 wt%) exhibit the highest values of the photo-responsivity and quantum efficiency, ∼23.3 mA W−1 and 5.8%, respectively, showing an enhancement by a factor of ∼ 11.5× compared to those obtained from the photo-sensor based on pure P3HT.

Conductive water-based graphene suspension for electromagnetic interference shielding via spray coating on SiP module

Conductive inks have been widely used to develop electronic devices, such as sensors, RFID antennas, and transistors. Electronic utilization is a coating that forms conductive films for electromagnetic interference shielding (EMI Shielding). This process also can be employed to cover electronic modules called System in Package (SiP). A technology known as conformal shielding utilizes spray coating with metallic inks to form a conductive layer over the SiP. Traditionally, copper or silver inks have been the primary materials employed due to their high electrical conductivity. Conversely, these metallic inks are associated with significant costs, environmental impacts, and complex production methods. In this context, water-based graphene dispersion could be an alternative to EMI Shielding for electronic chips. Graphene is attractive due to its excellent electrical and thermal properties, reduced cost, and being an environmentally friendly material. In this study, a water-based graphene suspension was developed and applied via spray coating to form films for electromagnetic shielding. The graphene dispersion in water utilized Carboxymethyl cellulose (CMC). Characterizations of the graphene suspension, including morphology, particle size distribution, and chemical analysis, were conducted. The resistivity of the resulting films and their shielding effectiveness (SE) were measured. Electronic chip modules were painted to assess coverage. The study demonstrated the successful formulation of a stable water-graphene suspension exhibiting favorable electrical resistivity (2.8 × 10−2 Ω.cm) after drying at 300 °C for 1 h. The resulting film achieved a shielding effectiveness of −9 dB at 1.0 GHz. Graphene film completely covered the electronic chips, indicating an alternative conformal shielding.

Trunk-Inspired SWCNT-Based Wrinkled Films for Highly-Stretchable Electromagnetic Interference Shielding and Wearable Thermotherapy

HighlightsElephant trunk-inspired anisotropic wrinkling structures were formed on a sandwich-like conductive film through a controlled shrinking method.The wrinkled conductive network could withstand up to 200% tensile strain and exhibits a strain-enhanced electromagnetic interference shielding effectiveness when stretching parallel to the electric field polarization direction.

Cohesively improved conductivity, transparency, and stability of Ag NW flexible transparent conductive thin films by covering Al2O3 layer

Developing feasible Ag nanowire (NW) transparent conductive thin films (TCFs) with good conductivity, transparency, mechanical durability, strong adhesion, and high stability is a great challenge. Herein, novel TCFs composed of Ag NWs/Al2O3 on polyethylene terephthalate (PET) substrates with synchronously improved conductivity, transparency, mechanical durability, adhesion, and stability, are prepared. The corresponding values (before coating Al2O3: 13.0 Ω/sq. at 86.1 %, after coating Al2O3: 11.7 Ω/sq. at 87.7 %) indicate that the deposition of Al2O3 enhances the transparency and conductivity of Ag NW networks. Moreover, the resistance does not change significantly after 50 taping cycles and 2000 bending cycles with a bending radius of 5.0 mm, indicating the strong adhesion and good mechanical flexibility of Al2O3/Ag NWs composites. In addition, Al2O3/Ag NWs composites possess excellent stability to resist strong oxidizing, hot and humid environments. As a proof of concept, the flexible transparent heater prepared by Al2O3/Ag NWs composites is successfully demonstrated, verifying the practicability.

Tenfold Enhancement of Wear Resistance by Electrosynthesis of a Nanostructured Self‐Lubricating Al2O3/Sn(S)MoS2 Composite Film on AlSiCu Casting Alloys

Enhancing tribological performance through nanostructure control is crucial for saving energy and improving wear resistance for diverse applications. We introduce a new electrochemical approach that integrates aluminum (Al) anodization, tin alternating current (AC) electrodeposition, and anodic MoS2 electrosynthesis for fabricating nanostructured Al2O3/Sn(S)MoS2 composite films on AlSiCu casting alloys. Our unique process uses Sn‐modified MoS2 deposition to form robust solid lubricant MoS2–SnS electrodeposits within the nanochannels and microsized voids/defects of anodic alumina matrix films on the base materials, resulting in a bilayered Al2O3/SnSMoS2 and MoS2–SnS–Sn composite film. The AC‐deposited Sn enhances conductivity in the anodic alumina matrix film, acts as catalytic nuclei for Sn@SnS@MoS2 core‐shell nanoparticles and a dense top layer, and serves as a reductant for the direct synthesis of hybrid solid lubricant MoS2–SnS from MoS3 by anodic electrolysis of MoS42− ions. The resulting nanocomposite film provides a two‐fold increase in lubricity (friction coefficient (COF) μ = 0.14 ⇒ 0.07) and a ten‐fold improvement in wear resistance (COF μ < 0.2) compared to conventional Al2O3/MoS2 film formed by anodizing and reanodizing. The effectiveness of the Al2O3/Sn(S)MoS2 composite is further validated through real automotive engine piston tests.

Advanced manufacturing of high conductive graphene coatings on polyethylene terephthalate substrate through laser-induced processes and thermal optimization

Graphene holds immense promise for applications in sensors due to its exceptional properties such as large carrier mobility and high electrical and thermal conductivities. Nevertheless, the manufacture of high conductive graphene films onto flexible substrates remains a formidable challenge. This paper presented a novel method for the precise incorporation of high conductive graphene coatings onto polyethylene terephthalate (PET) through the back transfer of laser-reduced graphene oxide (LRGO) from Al2O3 ceramic to PET. A record-low sheet resistance for LRGO so far, approximately 12 Ω/sq. was achieved, meantime exhibiting 5B level adhesion performance with PET substrate. The sheet resistance of the transferred LRGO was measured and demonstrated to be adjustable by manipulating laser power, scanning speed, and hatch distance. The analysis of reduction of graphene oxide (GO) involved a comprehensive examination of alterations in topography image, chemical bond content, C/O atomic ratio, and ID/IG intensity ratio. These observations provided insights into the factors contributing to the decrease of sheet resistance within LRGO. The adoption of a continuous gigahertz (GHz) femtosecond laser as the light source, coupled with the incorporation of thermally conductive Al2O3 plate as a heat sink, facilitated the manufacturing processes including reduction and transfer of GO. The manufacture of graphene coatings with high electrical conductivity on PET in a versatile and cost-effective manner, presents significant potential for diverse applications, particularly in conductive-coatings-based sensors.

Intrinsic doping and ageing of indium oxide thin films

Indium oxide (In2O3) is one of the most used materials for the synthesis of transparent electronics devices and currently tin-doped indium oxide (ITO) dominates the field of Transparent Conductive Oxides for most applications, from ICT to photovoltaics. In this work we present a study on the responses of indium oxide upon the formation, and stabilization, of point defects induced with different methods. After the deposition of In2O3 thin films via RF magnetron sputtering, treatments such as Ion Implantation (I.I.), Ultraviolet (UV) irradiation and Sun exposure were employed to generate oxygen vacancies as intrinsic dopants. Both I.I. and UV irradiations significantly improved the electrical conductivity of films, increasing the carrier density by up to 3 orders of magnitude. Moreover, after I.I. also the crystalline quality of the films was enhanced.To monitor the stability of oxygen vacancies upon exposure to ambient atmosphere, the ageing of samples was followed and recorded for a couple of weeks, reporting a fast and strong degradation of electrical properties. As a facile strategy to counteract the sheet resistance increase, samples were encapsulated in an ultra-thin (≈10 nm) SiO2 layer deposited via sputtering. Irradiated and encapsulated films retained a much lower sheet resistance throughout the observation time, preserving the samples conductivity.

Simulation and interpretation of zinc and nitrogen dopants induced defect emissions in monoclinic gallium oxide

Zinc (Zn) and nitrogen (N) are potential acceptor dopants for inducing visible emissions and p-type conductivity in monoclinic gallium oxide (β-Ga2O3), however, the poor understanding of these dopants and their recombination process severely limited the optoelectronic applications. Here, we investigate the zinc (Zn) and nitrogen (N) dopants-induced intraband states and the broadening of defect emission bands due to vibronic coupling of highly transparent β-Ga2O3 films through chemical and optical analyses, as well as density function theory. Incorporating Zn and N in β-Ga2O3 shifts the valence band edge towards the Fermi level and introduces band tail states above the valence band maximum. The emission band from pure β-Ga2O3 becomes significantly broad with the incorporation of Zn and N resulting in two additional emission bands: green luminescence (GL) and red luminescence (RL) along with the characteristic ultraviolet luminescence (UVL) and blue luminescence (BL) of pristine β-Ga2O3. Furthermore, the defect states responsible for these UVL, BL, GL, and RL emissions and their phonon coupling strengths are estimated by simulating the spectral line shape of these emission bands using the configuration coordinate model. The simulation results indicate that the Zn and N dopants-induced intraband states are responsible for the GL, and RL bands. These intraband states are acceptors, which provide p-type conductivity in β-Ga2O3 film.

The preparation of polystyrene/nickel core-shell particles for anisotropic conductive films (ACFs)

The use of core-shell conductive microspheres as conductive fillers for anisotropic conductive films (ACFs) has broad application prospects for high-precision circuit connections. However, existing preparation methods suffer from environmental pollution and a relatively long processing procedure. Therefore, we propose a bio-inspired, simple, and environmentally friendly method for preparing PS/Ni core-shell conductive particles suitable for ACFs. Specifically, this study utilized the oxidative self-polymerization of dopamine (DA) to modify the surface of polystyrene (PS) microspheres. The catechol groups in polydopamine (PDA) act as both reducing agents and anchor groups for palladium (Pd) atoms to catalyze the electroless nickel plating. Results indicated that the amount of (PDA) on the PS surface and the morphology of the formed nickel-phosphor (NiP) layer were regulated by adjusting the DA polymerization time and concentrations. The prepared PS-PDA/Ni conducting particles with an average diameter of 2 ± 0.2 μm has a low density (1.5 g/cm3) and can be applied to ACFs. The application of the prepared ACFs was demonstrated by bonding two flexible print circuits (FPC) with a line spacing of 200 μm. Good adhesion, conductivity, and anisotropic properties were observed in the bonded FPC-200s. This study provides useful information for producing suitable conductive particles with easy synthesis for ACFs applications.