Composite Films Research Articles

Gluten-Based Composite Film for Smart Food Packaging Applications

Gluten-Based Composite Film for Smart Food Packaging Applications

Shrouding Gas Plasma Deposition Technique for Developing Low-Friction, Wear-Resistant WS2-Zn Thin Films on Unfilled PEEK: The Relationship Between Process and Coating Properties

In this study, tungsten disulfide–zinc (WS2-Zn) composite films were generated on polyether ether ketone (PEEK) disks by an atmospheric pressure plasma jet (APPJ) equipped with a shrouding attachment. The friction and wear properties of the WS2-Zn coatings were intensively investigated by using a rotational ball-on-disk setup under dry sliding and ambient room conditions. In order to gain more information about the lubrication mechanism, the coating areas as deposited and the worn areas (i.e., in the wear track) were analyzed with a scanning electron microscope (SEM) with regard to their chemical composition in depth by energy-dispersive X-ray spectroscopy (EDS). X-ray photoelectron spectroscopy (XPS) was conducted to obtain precise chemical information from the surface. The results indicated that WS2-Zn coatings significantly improved the tribological properties, exhibiting a coefficient of friction (COF) of <0.2. However, the tribological performance of the coatings is strongly dependent on the plasma process settings (i.e., plasma current, dwell time of the powder particles in the plasma jet), which were tuned to reduce the oxidation by-products of WS2 to a minimum. The COF values achieved of the dry lubricant films were significantly reduced in contrast to the uncoated PEEK by a factor of four.

Synthesis and Characterization of TiO2 Thin Films Modified with Anderson-Type Polyoxometalates (Ni, Co, and Fe)

In this work, TiO2 and Anderson-type polyoxometalates (Ni, Co, and Fe) thin-film composites were fabricated. The composites were characterized by FTIR and Raman spectroscopy, diffuse reflectance, and scanning electronic microscopy. The methylene blue (MB) photocatalytic degradation on the composites under UV irradiation was studied. Spectroscopic results verified the modification of TiO2 thin films. Optical and morphological properties changed after TiO2 modification. The largest change in the optical band gap was observed for the FePOM/TiO2 system, which reported a value of 3.05 eV. The POM/TiO2 systems were more efficient in methylene blue (MB) adsorption than bare TiO2. Furthermore, the modified films were more efficient than bare TiO2 during MB photodegradation tests. The NiPOM/TiO2 and the CoPOM/TiO2 were the most efficient in the MB adsorption, reaching ~20%. The NiPOM/TiO2 and the CoPOM/TiO2 composites were the most efficient in the photodegradation process, reaching ~50% of MB removal. The stability tests indicated that composite films were moderately stable after the three performed reusability cycles. Thus, these results suggest that POM modification of TiO2 can improve the adsorption and photodegradation capacity of semiconductors.

Triple‐structured polyvinylidene fluoride‐based composite films with high conductivity and EM shielding properties

AbstractFunctionalized thin films with excellent flexibility and conductivity can meet the current requirements for electromagnetic(EM) shielding materials. In this paper, 2D transitions metal carbide and nitride nanomaterials Ti3C2Tx MXene were prepared by chemical exfoliation, and PVDF/MWCNTs/3 wt%/RGO@Fe3O4@ AgNWs‐10 based on PVDF/MWCNTs‐3 wt%/RGO@Fe3O4@AgNWs‐10, The samples were prepared through a simple solution mixing process followed by vacuum‐assisted filtration (VAF), and PVDF/MWCNTs/MXene/RGO@Fe3O4@AgNWs three‐layer PVDF‐based composite films, which were analyzed for electrical conductivity and EM shielding properties, which increased and then decreased with the rise in the Ti3C2Tx MXene content, in which the highest electrical conductivity of the three‐layer composite films of M3/MX‐10/R@F@Ag was obtained when the Ti3C2Tx MXene addition amount reached 10 mL as 3.9 × 103 S/m, the EMI SET is 54.9 dB, the EMI SEA is 44.8 dB, the absorption loss is 81.6%, and the SSEt of the M3/MX‐10/R@F@Ag three‐layer composite film is the highest 1672.5 dB/(cm−2·g). And the SEA/SER ratios of the M3/MX‐X/R@F@Ag three‐layer composite films are all greater than 1. The result shows that the EM attenuation mechanism of the M3/MX‐X/R@F@Ag three‐layer composite films is primarily driven by absorption loss and that the incorporation of Ti3C2Tx Mxene improves the EM shielding performance of the composite films. The relatively novel exploration of the performance study and structural design of the M3/MX‐X/R@F@Ag three‐layer EM shielding composite film provides structural design and research ideas for the application of the new MXenes material in EM shielding composites.Highlights The addition of Ti3C2Tx MXene will generate more conductive network nodules A complete 3D conductive network is constructed in the membrane This paper discusses the influence of Ti3C2Tx MXene on EM shielding Multiple internal reflections of EMW between Ti3C2Tx MXene 2D nanosheets The EM shielding mechanism of the film is discussed from the angle of 3D

A novel ε-polylysine-reinforced pullulan/curdlan-active film for an efficient preservation of fresh-cut fruit and vegetable.

In this study, a novel active film was developed by employing ε-polylysine (ε-PL) as a filler in pullulan/curdlan (P/CD) composite film (P/CD/ε-PL). The results showed that the structure of P/CD films was more uniform and denser compared to pullulan films, due to the good compatibility and intermolecular interaction between them. Among P/CD films, P/CD 6:1 film showed improved hydrophobicity, mechanical and barrier properties, and thermal stability, thereby selecting it for further use. Thereafter, the addition of ε-PL further enhanced the structural and physicochemical properties of prepared P/CD/ε-PL composite films, especially for P/CD/2.5%ε-PL composite film. It exhibited improved ultraviolet barrier (about 80% at 200-400nm), antibacterial activity (>90% against Staphylococcus aureus and Escherichia coli), and anti-fog properties (clearly visible and transparent background). Furthermore, P/CD/2.5%ε-PL composite film exerted its preservation effect on fresh-cut peppers and kiwis during storage, delaying the softening, consumption of soluble solids, and deterioration. Therefore, the developed P/CD/2.5%ε-PL composite film provided promising applications of active packing film. Practical Application: Fresh-cut fruits and vegetables are prone to deteriorate during storage, and active packaging films play a crucial role in retaining their quality. This study was conducted to prepare a composite film by blending pullulan, curdlan, and ε-PL and explore its structural, physicochemical, and functional properties, further verifying the preservation effect on fresh-cut peppers and kiwis. Compared to polyethylene film, the P/CD/2.5%ε-PL composite film delayed the softening, consumption of soluble solids, and deterioration of fresh-cut peppers and kiwis during storage. It provides a new perspective on the preservation of fresh-cut fruits and vegetables.

The Fabrication of Polyimide-Based Tunable Charge Traps Ternary Memristors Doped with Ni-Co Coated Carbon Composite Nanofibers

In the dynamic fields of information science and electronic technology, there is a notable trend towards leveraging carbon materials, favored for their ease of synthesis, biocompatibility, and abundance. This trend is particularly evident in the development of memristors, benefiting from the unique electronic properties of carbon to enhance device performance. This study utilizes sensitized chemical evaporation and spin-coating carbonization techniques to fabricate nickel-cobalt coated carbon composite nanofibers (SC-NCMNTs). Novel polyimide (PI) matrix composite memory devices were fabricated using in situ polymerization technology. Transmission electron microscopy (TEM) and micro-Raman spectroscopy analyses validated the presence of dual interface structures located between the Ni-Co-MWNTs, carbon composite nanofibers, and PI matrix, revealing a significant number of defects within the SC-NCMNTs/PI composite films. Consequently, this results in a tunable charge trap-based ternary resistive switching behavior of the composite memory devices, exhibiting a high ON/OFF current ratio of 104 and a retention time of 2500 s at an operating voltage of less than 3 V. The mechanism of resistive switching is thoroughly elucidated through a comprehensive charge transport model, incorporating molecular orbital energy levels. This study provides valuable insights for the rational design and fabrication of efficient memristors characterized by multilevel resistive switching states.

Phototuning of Multi-Color Emission in PMMA Composite Films for Information Encryption Applications

A strategy centered on dynamically tunable excited-state proton transfer (ESPT) processes is proposed for the design and synthesis of luminescent compounds. An emitter based on guanidine-substituted 1,8-naphthalimide (R-1) with ESPT characteristics has been meticulously engineered. Upon incorporation into poly (methyl methacrylate) (PMMA) matrices, the tunable ESPT process, transitioning between blue and yellow-green emission within the composite film, can be precisely controlled through irradiation in different pH environments. Moreover, the luminescence of the R-1/PMMA composite film exhibits variations in response to environmental changes, and demonstrates excellent fatigue resistance. Exploiting this characteristic, information such as “2020” can be encoded, and this encoded information automatically manifests in response to fluctuations in external pH. Specifically, employing a designated method is essential for accurately deciphering the information. The pH-dependent nature of this feature imparts a higher level of security to the material and offers new insights into information encryption.

Low-temperature Deposited Highly Sensitive Integrated All-Solid Electrodes for Electrochemical pH Detection

This article describes the process of fabricating an integrated all-solid electrode (IASE) by integrating thin films of titanium dioxide (TiO<i>2</i>) and silver/silver chloride (Ag/AgCl) onto an indium tin oxide (ITO) substrate. The fabrication of a pH sensing electrode (SE) involved utilizing a spin-coated thin film composed of TiO<i>2</i>. Thermally produced thin films of Ag/AgCl were used to develop solid reference electrodes (RE). The present work examined the impact of the drying process on the pH sensitivity and linearity of the low-temperature deposited IASE. The drying procedure was carried out within a temperature range from room temperature to 100°C. The investigation involved the examination of crystallinity, surface morphology, and thin film composition through the utilization of field effect scanning electron microscopy (FESEM), X-ray diffraction (XRD), and energy-dispersive X-ray (EDX) methods. In addition, a comparison was made between the pH sensing performance of the IASE and a commercially available Ag/AgCl RE. The findings of this research demonstrate that the IASE sample, which underwent a drying process at a temperature of 100°C, exhibited remarkable sensitivity and linearity values of 66.7 mV/pH and 0.9827, separately, when compared to the commercially available RE.

A flexible porous polyimide/copper composite film toward high-mass-loading anodes in lithium-ion batteries

Conventional metal foil current collectors are essential for electronic conduction in lithium-ion batteries, but the planar structure limits the fast transporting of electron and the power density. Herein, a light, conductive, self-extinguishing, and flexible porous polyimide/copper composite film (PIF/Cu) derived from a polyimide foam was fabricated via hot pressing and electroless plating methods. The honeycomb structure was illustrated in PIF/Cu under a 3D X-ray tomography microscope, revealing the successful construction of a 3D conductive network. PIF/Cu-30 possessed an electronic conductivity of as high as 3.6 × 105 S m−1 at a bulk density of 0.26 g cm−3 and exhibited exceptional structural stability even after successive and harsh mechanical loads. Graphite with a mass load of 12 mg cm−2 was loaded into the PIF/Cu-30 to prepare the anode for cell assembly. The cells using PIF/Cu-30 achieved a better performance in capacity retention (98.2 %@60 cycles) than those using traditional Cu foils (55.1 %@60 cycles), which resulted from the fast transport of electrons and Li-ion through the 3D conductive networks in the porous PIF/Cu-30.

Flexible multifunctional composite films for adjustable EMI shielding behavior under self-fixed deformation

With the widespread application of electromagnetic technology, the significance of intelligent electronic devices in modern communication is increasingly prominent. Despite this, the public focuses more on the harm caused by electromagnetic pollution. However, traditional EMI shielding materials struggle to meet the diverse and dynamic application requirements. Hence, developing materials capable of adjusting EMI shielding has become imperative to satisfy various scenarios. This paper presents the composite film TAPU-MXene, which is capable of adjustable EMI SE under self-fixed deformation. Introducing tannic acid increases the innermolecular interactions of TAPU. This enhancement leads to remarkable improvements in mechanical performance, achieving a stress level of 36.6 MPa at a strain of 560 %. Furthermore, the catechol groups can establish non-covalent interactions with multiple substrates, endowing the TAPU film with remarkable adhesion and self-healing capabilities. By combining the highly conductive nano-filler MXene with TAPU, the EMI shielding composite film TAPU-MXene is obtained. The EMI SE of TAPU-MXene was up to 56.7 dB when MXene loading was 3 mg cm−2. Most importantly, TAPU-MXene exhibits the ability to adjust the EMI shielding effectiveness from 56.7 dB to 2.75 dB under self-fixing deformation through shape memory mechanism, demonstrating promising applications in the field of adjustable EMI shielding materials.

Synthesis of Carboxylate-Dialdehyde Cellulose to Use as a Component in Composite Thin Films for an Antibacterial Material in Wound Dressing

Synthesis of Carboxylate-Dialdehyde Cellulose to Use as a Component in Composite Thin Films for an Antibacterial Material in Wound Dressing

Flexible Piezoelectric Nanocolumnar Composite Films as Flat-Panel Loudspeakers: Application and Modeling.

Highly anisotropic piezoelectric composites promise to progress electroacoustic devices as a class by combining the advantages of both piezoceramics and polymers. Fundamentally, piezoelectric loudspeakers employ the converse piezoelectric effect to convert electrical to mechanical energy. Quasi-1-3 piezoceramic/polymer composites enable flat-panel loudspeakers that are tunable in elastic modulus, with opportunities for mechanical flexibility, optical transparency, and large-area coverage. Their processing route enables relatively flexible design parameters, such as the particle loading, polymer-matrix modulus, film thickness, film size, and electrode-material stiffness. Alternative processing routes of electric field (E-field) aligned-piezoelectric composites are demonstrated, including using the relaxor ferroelectric lead magnesium niobate-lead titanate (PMN-PT) to enhance the acoustic performance and photocurable resins to accelerate the materials processing. Material properties critical for dielectrophoresis are characterized, and loudspeakers were fabricated based on the optimal processing conditions. Subsequently, electroacoustic characterization explores the effect of loudspeaker size, substrate stiffness, the microphone distance, the piezoceramic material, and the matrix modulus. Finally, finite-element (FE) modeling of the electromechanical behavior validates the natural frequencies and modes shapes of the loudspeakers via the analytical solution and frequency response to electrical and mechanical excitation. Good correspondence between the predicted electroacoustic performance and experimentally validated model is observed.

High-sensitivity fiber temperature sensor based on composite film structure and lossy mode resonance

In this work, we proposed and demonstrated a high-sensitivity optical fiber temperature sensor based on lossy mode resonance (LMR). The sensor is composed of a D-shaped fiber and a thin composite film. The composite film consists of tin dioxide (SnO2) and polydimethylsiloxane (PDMS). PDMS is inserted as an intermediate layer between D-shaped fiber and SnO2 layer, realizing the separation of TM and TE polarization to reduce polarization crosstalk, while also serving as a temperature sensitive layer. The polarization state of the excited LMR can be freely controlled by adjusting the thickness of the composite film. The proposed sensor exhibits a high temperature sensitivity of −1.1883 nm/°C with a measurement range of 10–90 °C. Meanwhile, a fast response time of ∼ 109 ms was observed due to the ultra-thin PDMS interlayer.

The effect of NaY‐zeolite on mechanical, thermal, and spectroscopic behavior of crosslinked polyvinyl alcohol films

AbstractThe effects of sodium y zeolite (NaY‐zeolite) on crosslinked Polyvinyl alcohol (CrPVA) composite films were investigated. The spectroscopic analysis showed that crosslinks were formed between PVA, Tartaric acid (TA), and NaY‐zeolite particles. The thermal stability of the CrPVA film was improved with the addition of zeolite. Optimum thermal stability was observed for 5 wt % zeolite content. It can be seen that the mechanical properties also improved for 5 wt % zeolite‐doped CrPVA composite films when compared with CrPVA. It was observed that Young's modulus increased 54.14 to 74.49 MPa. While the degree of crystallinity of the composite film decreased from 20.42 to 14.77% due to zeolite content. This is thought to be due to the increase in the structure's crosslinking rate. The utilization of TA and NaY zeolite in membrane applications may be considered an advantage for improving the mechanical characteristics and the recyclability of membrane technology.

Enhanced Energy Storage Properties of Four-Layer Composite Films via Strategic Macrointerface Modulation.

Dielectric capacitors play a crucial role in the field of energy storage; however, the low discharged energy density (Ue) of existing commercial dielectrics limits their future applications. Currently, further improvement in the Ue of dielectrics is constrained by the challenge of simultaneously achieving high permittivity (εr) and high breakdown electric field strength (Eb). To address this issue, we designed a series of four-layer poly(vinylidene fluoride) (PVDF)-based composite films comprising three functional layers: a sodium bismuth titanate (NBT) plus PVDF composite (NBT&PVDF) layer to achieve high εr values and a pure PVDF layer and a boron nitride (BN) plus PVDF composite (BN&PVDF) layer to achieve high Eb values. This design synergistically enhanced the εr and Eb values of the composite films by exploiting low-loss macrointerface polarization via adjustment of the functional layer stacking order, as supported by simulation analyses. Ultimately, the composite film with a topmost layer of pure PVDF, followed by an NBT&PVDF layer, another pure PVDF layer, and a BN&PVDF layer achieved an enhanced Ue value of 26.42 J·cm-3 and excellent efficiency of 80.03% at an ultrahigh Eb value of 770 MV·m-1. This approach offers an innovative pathway for developing advanced energy storage composite dielectrics via macrointerface manipulation.

Effect of thiourea concentration on the structural, optical and photoelectric properties of ZnO/ZnS/PVC composite films used as flexible UV photodetectors

Effect of thiourea concentration on the structural, optical and photoelectric properties of ZnO/ZnS/PVC composite films used as flexible UV photodetectors

A Comprehensive Review about Risks of Type-II Diabetes on Ocular Tear Film

Millions of people worldwide suffer from diabetes mellitus (DM), which can lead to systemic issues in a number of organs. Ocular problems, such as dry eye syndrome (DES), are among its less well-known side effects. This review delves into the interactions between diabetes and the composition of tear films, emphasizing alterations in the mucin, aqueous and lipid layer. Dry eye symptoms are exacerbated by induced changes in the components of the tear film in diabetes DM, which lead in decrement in tear production, increment in tear evaporation and tear film instability. Lipid layer is a lubricant, that reduces friction between the ocular surface and the eyelids which promotes high-quality, smooth refractive surface. The lacrimal function unit shields the tear film, preserves the normal function of the ocular surface. The mucin layer is secreted by the conjunctival goblet cells, in hyperglycemia the functionality of the cells are reduced thus, the mucin secretion is also altered which causes instability of the tear film. Diabetic patients can have their tear film integrity assessed with the help of diagnostic methods like Schirmer's Test and Tear Break- Up Time (TBUT). In order to relieve symptoms and maintain ocular health, there should be a complete management of diabetes and the induced tear film disorders.

Catalytically Active Gold Nanoparticles on Star Block Co-polymer Matrix: Synthesis of Nanocomposite Film Exploring the Langmuir-Blodgett Technique.

Nanocomposites with metal nanoparticles and block copolymers distributed in a stable and robust thin film are preferred for various applications. Here, synthesis of such a nanocomposite is reported, which is composed of gold nanoparticles (AuNPs) embedded in a tetronic 701 (T701) and 90R4 (T90R4) thin film matrix generated using the Langmuir-Blodgett (LB) thin film technique. Tetronics contain a monoprotonated central ethylenediamine group at pH 5 due to the presence of chloroauric acid (HAuCl4) in the subphase, along with poly(ethylene oxide) (PEO) and poly(propylene oxide) (PPO) blocks, both of which have the capacity to serve as the reducing agent toward chloroaurate anion (AuCl4-). Calorimetric experiments have shown that T90R4 has a better interaction with AuCl4-, probably due to its better electrostatic interaction with AuCl4- ions due to the higher % of the hydrophilic PEO group. On the other hand, the T701-AuNP interaction turned out to be more spontaneous due to the higher hydrophobicity of T701 (higher PPO/PEO ratio). The optical properties and structure/morphology of these nanocomposites are characterized by UV-vis spectroscopy, FTIR spectroscopy, XRD, and TEM. The composite thin film has the ability to catalyze the organic electron transfer process between p-nitrophenol and p-aminophenol in the presence of sodium borohydride. A clear correlation has been found between the reaction rates and the kind of tetronic present in the nanocomposite, which acted as a matrix and stabilizer toward AuNPs.

Analysis of composite wavelength multilayer dielectric film damage based on the field-thermal effect

Taking SiO2/HfO2 multilayer dielectric films as the research object, when the total laser energy is the same, the effects of different laser parameters on film damage under 1064 nm and 355 nm composite wavelength pulse irradiation are analyzed. The results show that different energy ratios lead to exponential differences in the electron number density inside the film, but they are far from reaching the field damage threshold. Comprehensive analysis shows that film damage is mainly affected by thermal melt and stress. The greater the difference between an energy ratio of 1ω and 3ω, the greater the thermal stress in the film, the higher the stress peak, and the more obvious the damage effect of thermal stress on the film. Under the condition of 50%1ω, the thermal effect in the film is minimal, which can ensure that the film is not damaged as much as possible. The model method used in this paper only takes the current film system as an example for specific research and can be extended to all film systems for analysis.

Preparation and Characterization of Tensile Properties of PMMA/SiC Nanowhiskers Nanocomposite Films: Effect of Filler Loading and Silane Treatment

The preparation of nanocomposites through melt mixing was challenging as the nanofillers tend to form agglomeration. The silicon carbide nanowhiskers (SiCNWs) filled poly (methyl methacrylate) (PMMA) thin film in this study was prepared by means of solution casting. Acetone with low toxicity was used as solvent to dissolve the PMMA pellets. A coupling agent, silane was used to enhance the properties of composite films. Besides, the untreated and treated SiCNWs were filled into PMMA matrix, respectively with the filler loading varied from 0.2 to 0.8 wt%. The universal testing machine was used to investigate the tensile properties of composites. It was found out that the tensile strength of the PMMA was reduced in the presence of SiCNWs. However, the tensile strength had increased with the rise of filler loading. At 0.8 wt% of SiCNWs, the composites’ tensile strength was comparable to virgin PMMA. Meanwhile, the SiCNWs had reduced the elongation at break but increased the elastic modulus of PMMA/SiCNWs nanocomposite films. In addition, silane surface treatment on SiCNWs had improved the tensile strength and ductility but lowered the elastic modulus of the nanocomposites. The improvement was due to the enhancement of interfacial adhesion between SiCNWs and PMMA.