Insulation Characteristics Research Articles

Research on Leakage Current Waveform Spectrum Characteristics of Artificial Pollution Composite Insulator

In order to know about the change features of leakage current during the pollution flashover process of composite insulators, the study of the pollution flashover test on composite insulator under the pollutional condition is presented in the artificial fog cabinet. The characteristics of leakage current waveforms in time-domain and frequency-domain are measured and analyzed during the test. The analysis results show that there is a strong correlation among the fundamental harmonic, the third harmonic and fifth harmonic. The characteristics of leakage current spectrum are represented by the maximum value of leakage current (Im), total harmonic distortion (THD), and phase difference of fundamental leakage current (θ). During a near-flash event, the leakage current exhibits high amplitude, low harmonic content, and small phase difference between the fundamental leakage current and voltage. The research findings provide a basis for establishing a pollution flash warning system based on leakage current characteristic quantities.

UV/Ozone-Treated and Sol-Gel-Processed Y2O3 Insulators Prepared Using Gelation-Delaying Precursors.

In this study, a Y2O3 insulator was fabricated via the sol-gel process and the effect of precursors and annealing processes on its electrical performance was studied. Yttrium(III) acetate hydrate, yttrium(III) nitrate tetrahydrate, yttrium isopropoxide oxide, and yttrium(III) tris (isopropoxide) were used as precursors, and UV/ozone treatment and high-temperature annealing were performed to obtain Y2O3 films from the precursors. The structure and surface morphologies of the films were characterized via grazing-incidence X-ray diffraction and scanning probe microscopy. Chemical component analysis was performed via X-ray spectroscopy. Electrical insulator characteristics were analyzed based on current density versus electrical field data and frequency-dependent dielectric constants. The Y2O3 films fabricated using the acetate precursor and subjected to the UV/ozone treatment showed a uniform and flat surface morphology with the lowest number of oxygen vacancy defects and unwanted byproducts. The corresponding fabricated capacitors showed the lowest current density (Jg) value of 10-8 A/cm2 at 1 MV/cm and a stable dielectric constant in a frequency range of 20 Hz-100 KHz. At 20 Hz, the dielectric constant was 12.28, which decreased to 10.5 at 105 Hz. The results indicate that high-quality, high-k insulators can be fabricated for flexible electronics using suitable precursors and the suggested low-temperature fabrication methods.

Radiative cooling performance analysis of cooling wood with three delignification processes for building applications

The delignification process is essential in the preparation of radiative cooling wood, and optimizing the delignification process is crucial for achieving a balance in the optical, mechanical, and thermal insulation characteristics of the delignify wood. Using the orthogonal experimental method, the study explored the influence of different delignification processes (such as chlorite, sulfite, and hydrogen peroxide methods), treatment duration, temperature, and other factors on wood weight loss rate, infrared spectroscopy, tensile and flexural strength, thermal conductivity, reflectance, and emissivity in order to obtain the best delignification process parameters for preparing radiative cooling wood with the optimal overall performance. The experimental results showed that delignification treatment followed by hot pressing improved the mechanical properties of the wood. As the delignification temperature and duration increased, the wood weight loss rate also increased, the mechanical properties declined, and the thermal insulating properties improved. The comprehensive comparison revealed that using the hydrogen peroxide method with treatment temperature at 80 °C and lasting 4 h can achieve the best overall performance for radiative cooling wood. Compared with Balsa wood, the tensile strength increased by 4.2 times and the flexural strength by 2.3 times, while the thermal conductivity reached 0.08 W/mK. In outdoor experiments, this radiative cooling wood can attain a good cooling effect throughout the day. During the noon hours, its surface temperature was lower than that of cement and the ambient temperature by 11.4℃ and 4.4℃ respectively, and the net radiative cooling power was up to 46 W/m2. The results show broad prospects for its application in building insulation and energy saving.

A Multifunctional Approach to Optimizing Woven Fabrics for Thermal Protective Clothing

This paper presents a detailed exploration of the development and characterization of multifunctional dual-purpose woven fabrics for thermal protective clothing. Through this research, 69 woven fabric prototypes have been carefully designed and produced, integrating various raw materials, yarn, and woven fabric construction parameters, with the aim of optimizing thermal protection properties while ensuring comfort and durability. The analysis led to the identification of two optimal woven fabric samples, which, upon further testing, exhibited exceptional dimensional stability, crease recovery, tear resistance, as well as abrasion and water resistance. Furthermore, the thermal properties were evaluated, demonstrating exceptional flame resistance, limited heat transmission, and high thermal insulation. Additionally, the study evaluated dynamic thermal properties, contact conductive heat transfer, air permeability, water vapour resistance, and thermal resistance of two clothing systems constructed from selected woven fabrics. Statistical analysis confirms significant differences between clothing systems, highlighting the influence of yarn composition and fabric structure on thermal performance and comfort, where one system exhibits better thermal insulation characteristics suitable for colder environments while the other excels in breathability for warmer climates. The developed woven fabrics meet high standards for protective clothing against heat and flame, surpassing currently available comparable woven fabrics on the market in terms of efficacy and performance. This research provides insights into the intricate balance between protection, comfort, and durability of woven fabrics, contributing to advancements in protective textile technology.

Vibrational response of a sandwich microplate considering the impact of flexoelectricity and based on a novel porous-FGM formulation

Flexoelectricity indicates a unique characteristic of insulators and dielectric materials that results in electrical polarization induction in response to the non-uniform strain gradient. The impact of this property is bolder on the microscale and nanoscale rather than the macroscale. This article is conducted to derive the governing equations of motion for a flexoelectric-multilayer structure and evaluate its vibrational behavior in response to various variable variations. The model includes a functionally graded (FG) porous core which is confined between two flexoelectricity-based face sheets at both sides and a Vlasov type of foundation. To gain the governing equations, the new type of power law for porous material beside Hamilton’s principle (HP) and modified couple stress theory (MCST) is implemented. Capturing the effects of length scale parameter, different materials, aspect and thickness ratios, porosity index, foundation parameter and boundary conditions (B.C.s) on the normalized natural frequency (NNF) of such a multilayer model based on the novel FG porous material formulation serve as the main novelty of this article. According to the results, it is revealed that the lateral ratio enhancement causes NNF and stiffness reduction in the model. Furthermore, among all considered B.C.s, simply support (SSSS) and clamped support (CCCC) refer to the lowest and the highest NNF respectively. The content of the recent article serves as a good source to provide a better understanding of the vibrational response of high stiffness-to-weight ratio structures to different variable variations.

Enhanced electrical properties of polypropylene insulation based on β‐nucleated crystallization regulation for high‐voltage direct current cable

AbstractThis study investigates the effect of crystallisation regulation on the electrical properties of β‐modified polypropylene (PP) insulation. Various β‐modified polypropylene insulation samples are prepared by controlling the melting temperature within the range of 180°C–200°C, and the ensuing crystallization characteristics of polypropylene insulation are evaluated. It is observed that the crystallinity decreased with increase in melting temperature, while the β crystal fraction and the lamellae long period increased. Notably, PP insulation subjected to a melting temperature of 200 °C demonstrates a substantial 47.1% decrease in DC conductivity, accompanied by a notable 22.6% reduction in space charge accumulation, concomitant with a significant 14.6% enhancement in DC breakdown strength. Additionally, a higher β crystal fraction in PP insulation is found to correspond to an increased density of deep traps, notably at an energy level of 0.95 eV. The elevated melting temperature effectively eradicates the melting memory effect, thereby facilitating the induction of β crystals by the β‐nucleating agents. The parallel lamellae structure inherent in β crystals serves to diminish interface defects between spherulites, consequently mitigating carrier mobility, curtailing space charge accumulation and enhancing breakdown strength.

SOUND AND THERMAL INSULATION PROPERTIES OF SANDWICH COMPOSITES MADE OF WASTE KEVLAR® MATERIALS

This paper examines the thermal and acoustic insulation characteristics of sandwich composites with waste Kevlar® fiber-reinforced face materials and polyurethane/paper cardboard cores. Waste Kevlar® short fibers (carding waste) were reinforced into the sandwich composites’ core part in varying ratios (2%, 5%, and 10%). Kevlar® fabric edge waste (waste of weaving process) was used to produce the face materials of sandwich composites. Sandwich composites were also stitched using Kevlar® yarns to observe the effect of the through-thickness reinforcement on sound and thermal insulation properties. The sound insulation test results showed that reinforcement of short Kevlar® fibers into the core parts of sandwich composites somewhat raised their sound absorption coefficients. Because the stitching holes created air spaces for sound vibrations, the sound absorption coefficient values improved. The sound transmission losses of sandwich composites were also increased up to 30 dB after short Kevlar® fiber addition. The thermal conductivity coefficient of sandwich composites decreased, indicating that the addition of Kevlar® fibers increased their insulation properties.

Methods of Mathematical Statistics in Analyzing Probabilistic Characteristics of External Insulation

Methods of Mathematical Statistics in Analyzing Probabilistic Characteristics of External Insulation

Three-dimensional nanostructures of crosslinked aramid nanofibers with exceptional mechanical and thermal insulation characteristics

Despite the remarkable attributes of aramid nanofibers, which include a high aspect ratio, elevated strength and modulus, as well as exceptional chemical and thermal stabilities, their utilization in three-dimensional porous nanostructures remains constrained due to the inherent challenge of agglomeration between adjacent fibers. This study presents a novel approach involving citric acid-assisted crosslinking to mitigate aramid nanofiber agglomeration. By facilitating the formation of covalent bonds between aramid nanofibers and citric acid, this method leads to the development of a three-dimensional open-porous structure. The chemically crosslinked aramid nanofibers/citric acid composite demonstrated notable enhancements in physical, mechanical, and thermal insulation properties, including an ultra-low density of 8.7 mg cm−3, exceptional compressive and tensile strengths at 3.04 MPa and 287 kPa, respectively, and a low thermal conductivity of 40 mW m−1 K−1. These advancements can be attributed to the preservation of the porous structure achieved through established covalent bonds. These findings carry significant implications for unlocking the potential of aramid nanofibers, particularly in advancing fields like thermal maintenance, insulation, construction of ultra-light structures, and the mitigation of vibration or impact energy in demanding environments.

Surface doping manipulation of the insulating ground states in Ta2Pd3Te5 and Ta2Ni3Te5

Abstract Manipulating emergent quantum phenomena is a key issue for understanding the underlying physics and contributing to possible applications. Here we study the evolution of insulating ground states of Ta2Pd3Te5 and Ta2Ni3Te5 under in-situ surface potassium deposition via angle-resolved photoemission spectroscopy. Our results confirm the excitonic insulator character of Ta2Pd3Te5. Upon surface doping, the size of its global gap decreases obviously. After a deposition time of more than 7 min, the potassium atoms induce a metal–insulator phase transition and make the system recover to a normal state. In contrast, our results show that the isostructural compound Ta2Ni3Te5 is a conventional insulator. The size of its global gap decreases upon surface doping, but persists positive throughout the doping process. Our results not only confirm the excitonic origin of the band gap in Ta2Pd3Te5, but also offer an effective method for designing functional quantum devices in the future.

Effect of surface energy on the contamination characteristics of porcelain double umbrella insulators

To explore the influence of surface energy on the contamination characteristics of insulators, COMSOL Multiphysics software was used to simulate the contamination characteristics of XWP 2-160 insulators under wind tunnel conditions, and the rationality of the modified expression of the dynamic deposition model of the contaminated particles was verified. The change of contamination characteristics before and after changing the surface energy of insulators under natural conditions was simulated and analyzed. The results show that under the original surface energy (72 mJ/m 2) and low surface energy (6.7 mJ/m 2) with the increase in particle size, the contamination amount of an insulator surface area decreases first and then increases. When the wind speed is 2 m/s, the change in the particle size has the most pronounced effect on the amount of contamination. The amounts of contamination for the low surface energy are 64–75%, 60–95%, 55–91% and 54–78% lower than those for the original surface energy for particle sizes of 10, 15, 20 and 25 μm, respectively. For the same wind speed, when the size of contamination particles increases, the difference between the ratio of DC and AC contamination accumulation is gradually increasing because of the influence of the electric field force. From the perspective of the insulator preparation process, the development of low surface energy insulators can improve their anti-fouling performance.

Impact of 3D air gap eccentricity on winding insulation temperature characteristic in PMSG

The static air gap eccentricity is one of the prevalent faults in permanent magnet synchronous generators. In previous studies, the variation of magnetic flux density, stator current and vibration have been studied mostly. However, the temperature characteristic of winding insulation under 3D static air gap eccentricity fault is rarely investigated. As a supplement, this paper comprehensively analyzes the influence of radial static air gap eccentricity, axial static air gap eccentricity and the combined static air gap eccentricity (radial static air gap eccentricity and axial static air gap eccentricity) fault on the winding insulation thermal response. The whole work is based on not only the loss of core and windings but also the temperature rise of the winding insulation, which is carried out through theoretical analysis, finite element calculation, and experiment verification. It is shown that radial static air gap eccentricity will increase the winding insulation temperature whatever in singe radial static air gap eccentricity or combined static air gap eccentricity, while axial static air gap eccentricity has the opposite effect. Specifically, the winding insulation temperature in radial static air gap eccentricity 0.1 mm, 0.2 mm and 0.3 mm cases are 57.18℃, 59.10℃ and 61.04℃, respectively, which is 3.29℃, 5.21℃ and 7.15℃ higher than that under normal condition. However, under axial static air gap eccentricity, winding insulation temperature will decrease by 1.84℃, 4.11℃ and 5.9℃, respectively. When axial static air gap eccentricity is unchanged and radial static air gap eccentricity is increased, the winding insulation temperature will increase by 1.5℃ and 3.23℃, respectively. On the contrary, when radial static air gap eccentricity is unchanged and axial static air gap eccentricity increases, the winding insulation temperature decreases by 2.54℃ and 5.66℃, respectively. The end part and the join between the end and line parts of the winding insulation are the most dangerous positions to suffer from static thermal wear.

A novel co-continuous Si–Zr hybrid phenolic aerogel composite with excellent antioxidant ablation enabled by sea-island-like ceramic structure at high temperature

Lightweight phenolic matrix composites are highly potential in ablative thermal protective materials for future aerospace vehicles, and hybrid modification is considered as one of effective ways to improve the oxidation and ablation resistance of phenolic matrix. Herein, the co-continuous silica zirconium hybrid phenolic resin (SZRx) was synthesized, which can be used to prepare lightweight ablation resistant aerogel composites by the sol-gel method. The SZRx aerogel showed stable porous structure and excellent hydrophobicity, and the silicon zirconium hybrid greatly improved the high temperature carbon residue and oxidation resistance of phenolic resin. The SZRx aerogel composites also possessed excellent integrated characteristics of heat protection and insulation, with a linear ablation rate as low as 0.032 mm/s and a back temperature below 200 °C. The synergistic effect of silicon and zirconium formed the multiphase ceramic layer (C, SiO2, SiC and ZrO2) with the sea-island-like structure on the surface of the composite material, which can effectively resist high-temperature ablation and aerodynamic exfoliation. This can indicate that silicon zirconium dual element hybrid phenolic resin is the highly competitive matrix for lightweight and ablation resistant composite materials.

Changing the Ca2+ ion ratio to modulate the temperature coefficient of resistivity (TCR) of La1-xCaxMnO3 films prepared by the sol-gel spin coating method

Perovskite manganese oxides are highly desirable for infrared acquisition owing to their characteristics of ferromagnetic metal-paramagnetic insulators. In this work, the sol-gel spin-coating technique was employed to prepare La1-xCaxMnO3 (LCMO) films with varying Ca2+ content (x = 0.1, 0.2, 0.3, 0.4, 0.5) on the (l00) LaAlO3 (LAO) substrates. In comparison to previous studies, the pre-sintering temperature, final sintering temperature, and final sintering period were modified. The crystal structure, surface topography, elemental valence states, and electrical transport performance of the LCMO films were characterized and analyzed as well. The results demonstrated that the diffraction peaks of the above films were aligned with those of the LAO single-crystal substrate. The change in Ca2+ content caused an increase in the Mn–O bond length, the amount of Mn4+, and the Mn–O–Mn angle in LCMO films, promoting the double exchange effect. These modifications had a considerable impact on the resistivity of LCMO films, increasing their TCR value. The maximum TCR of 22.92% K−1 was reached at x = 0.3 and peak TCR temperature (Tk) of 241.93 K. Therefore, the film has great application potential for infrared bolometers.

Cryogenic insulation performance of polyimide foam-filled fluted-core composite sandwich panels

Foam-filled composite sandwich structures have demonstrated superior thermal insulation performance, making them highly suitable for cryogenic tanks in launch vehicles. This study focused on the cryogenic insulation characteristics of carbon fiber-reinforced plastic (CFRP) fluted-core sandwich panels filled with polyimide foam. The fluted-core sandwich panel was simplified into a homogeneous multilayer plate to establish a one-dimensional heat transfer theoretical model. This model was used to predict steady-state temperature approximate solutions by linearizing the temperature-dependent thermal conductivity. The sandwich specimens were fabricated using an integrated forming co-cured method. Self-developed cryogenic insulation experiment and finite element simulations were conducted to acquire temperature distributions and validated the precision of the theoretical model. Results showed that the specimens achieved insulation temperature difference exceeding 143.05 °C, with effective thermal conductivity reaching 0.0326 W/(m·°C), significantly lower than that of CFRP. The temperature distributions along the thickness direction displayed a nonlinear increasing trend. The cryogenic thermal short effect was noticeable at the junction of the bottom facesheet and web. An analysis of geometric parameter influences revealed that increasing the short span, core height, or reducing web thickness could enhance thermal insulation characteristics with minimum effective thermal conductivity of 0.0276 W/(m·°C) and lead to a more uniform distribution of bottom temperatures with minimum temperature difference of 3.30 °C. These findings provide a foundational analysis for designing cryogenic insulation structures.

AC-DC breakdown characteristics of oil-paper insulation at low temperature

New energy sources such as wind energy are mainly distributed in low temperature areas such as high altitude and high dimensionality in inland China, which has higher requirements for the low-temperature insulation characteristics of power equipment. This poses higher demands for the low-temperature insulation capabilities of power equipment. However, the existing research on the low temperature breakdown characteristics of oil-impregnated paper is limited. In this study, the authors constructed an AC-DC combined power supply and a specialized low-temperature breakdown testing platform. Various oil-impregnated paper samples with different moisture contents were prepared. The paper investigated the AC-DC breakdown characteristics of these samples under low-temperature conditions, focusing on the effects of temperature, moisture content, and DC component on the breakdown strength. The findings serve as a valuable design reference for the application of oil-impregnated power equipment in low-temperature environments.

TMM-based study on sound insulation characteristics of laminated cylindrical shell lined with porous materials

TMM-based study on sound insulation characteristics of laminated cylindrical shell lined with porous materials

Impact of Accelerated Thermal Aging on Electrical Tree Structure and Physicochemical Characteristics of XLPE Insulation

Impact of Accelerated Thermal Aging on Electrical Tree Structure and Physicochemical Characteristics of XLPE Insulation

The 1/4 occupied O atoms induced ultra-flatband and the one-dimensional channels in the Pb10−xCux(PO4)6O4 (x = 0, 0.5) crystal

The search for room-temperature superconductors has been a long-standing goal in condensed matter physics. In this study, we investigate the electronic and geometric properties of lead apatite with and without Cu doping within the framework of the density functional theory. Based on our calculations, we found that without Cu doping, the lead apatite PPOO shows an insulator character with flatbands that straddle the Fermi level. Once we introduce O1 vacancies, the flatbands disappear. Furthermore, we analyze the effects of Cu doping on the crystal structure and the electronic band structure of the material PCPOO4. Our calculations reveal the presence of one-dimensional channels induced by fully occupied O1 atoms that are only 1/4 occupied in the literature, which may play a crucial role in the realization of room-temperature superconductivity. Based on our findings, we propose a possible solution to improve the quality of superconductivity by annealing the material in an oxygen atmosphere. These results contribute to a better understanding of the unusual properties of Cu-doped lead apatite PCPOO4 and will pave the way for further exploration of its potential as a room-temperature superconductor.

Analysis of the structure of electrically conductive composite ceramics

The object of the research is electrically conductive ceramics. It aims to analyze the microstructure of electrically conductive ceramic composites based on silicon carbide and investigate the influence of silicon carbide content on their properties. This study is pivotal for enhancing materials used in high-tech applications, particularly in fields where distinct electrical insulation and mechanical characteristics are crucial. The microstructure analysis conducted through scanning electron microscopy confirmed the presence of silicon carbide in all examined ceramic samples, except in those where silicon carbide was not added. Special attention should be given to the sample with 30 % silicon carbide, distinguished by the lowest open porosity. These findings are corroborated by previous research where this sample exhibited superior properties: open porosity – 12.51 %, water absorption – 5.88 %, apparent density – 2.13 g/cm³, specific resistance – 0.43·106 Ω·m. These characteristics indicate low porosity and high structural-physical property values. The results not only affirm the successful incorporation of silicon carbide into the ceramic matrix but also highlight the prospects for applying the researched ceramic materials in areas where electrical insulation and mechanical properties are crucial. Specifically, the sample with 30 % silicon carbide appears particularly promising due to its high characteristics and lower porosity, making it potentially interesting for applications in high-tech industries such as electronics and telecommunications. The conclusions suggest the potential use of these ceramic materials in various high-tech industries where both electrical and mechanical properties are essential. The sample with 30 % silicon carbide, with its exceptional characteristics, holds potential for applications in advanced technologies. Further research in this direction could lead to the development of new materials for effective radiofrequency absorption, finding broad applications in different technological fields.