Cationic Dye Research Articles

Advanced microcrystalline nanocellulose-based nanofiltration membranes for the efficient treatment of wastewater contaminated with cationic dyes

Advanced microcrystalline nanocellulose-based nanofiltration membranes for the efficient treatment of wastewater contaminated with cationic dyes

Photocatalytic application of nickel oxide/zinc oxide nanoparticles decorated kaolinite nanocomposite for the degradation of crystal violet

The photocatalysis process, which is effective, economical, and environmentally friendly can overcome rapidly increasing environmental problems, has shown rapid development in recent years. Nontoxic, low-cost natural minerals are often used in photocatalysis processes that remove organic pollution from wastewater. In this study, a selective method for the removal of crystal violet (CV) from aqueous solutions using nanocomposite of nickel oxide/zinc oxide nanoparticles (NiO/ZnO) supported on kaolinite photocatalyst was investigated. The raw kaolinite, bare NiO, bare ZnO and nanocomposite samples were characterized by the XRD, TEM, SEM-EDX, XPS and FTIR techniques. The photocatalytic performances of kaolinite-NiOZnO (K-NiO/ZnO) nanocomposite and bare samples were also investigated and comparatively evaluated by the photodegradation of CV (cationic dye) dye under visible light irradiation. The effects of various parameters such as the dosage of photocatalysis, contact time, and initial dye concentration on the rate of removal of dye were investigated and optimized. The kinetics of decolorization by samples can be well described by the pseudo-first-order model. Finally, it can be used in advanced oxidative processes for the degradation of organic pollutants.

Comments concerning papers about cationic dyes sorption, published by Saeed et al. (2023), Tan et al. (2023) and Yıldız et al. (2023)

ABSTRACT Recently, the three independent papers cited in the title were published in this journal, dealing with the sorption of cationic dyes on specially prepared solid sorbents. Although kinetics, isotherm and thermodynamics are three important components for the correct description of any sorption process, the authors of these original papers introduced several fundamental errors in these parts. Therefore, we present detailed analyses of these errors in the hope that this “Comment” paper will also be useful to other researchers (especially early career researchers) to avoid replicating such errors elsewhere in the future.

Removal of Methylene blue dye from contaminated wastewater using lignocellulosic biomasses: A comparative study

In this study, lupine seed (Lu-SP) and pumpkin seed shells (PSSP) biomasses were used to create alternative and effective adsorbents. Methylene blue (MB) dye was removed from wastewater using the as-prepared adsorbents at variables solution pH 2.0 –11.0, contact period (0–180 min), and adsorbent mass (0.2–2.0 g/L). The solution pH had a synergistic effect on the improved removal of MB and the optimal adsorption removal for both adsorbents occurred at pH 8.0 and 120 min. The adsorption isotherm modelling results showed a good fit with the Langmuir model, with a maximum monolayer adsorption capacity of 48.98 and 77.48 mg/g for PSSP and Lu-SP, respectively. Similarly, the pseudo-first-order (PFO) model is regarded as the best-fit kinetic model for both adsorbents and suggests the predominance of physisorption via interfacial diffusion. Mechanistic investigation of the present system suggests that both intraparticle diffusion and surface sorption mechanisms control the adsorption rate. Notably, the Lu-SP with a lower surface area (54.013 m2/g) outperformed the PSSP (235.992 m2/g) in terms of adsorption capacity under varying pH. Therefore, in addition to electrostatic interaction, adsorption into the micropores via volume filling is considered one of the adsorption mechanisms. This study, therefore, revealed that the PSSP and Lu-SP may be very helpful for removing cationic MB dye from contaminated wastewater.

Sustainable Conversion of Waste Carbon Brush and Fly Ash into a Novel Nanocomposite for Selective Adsorption of Cationic Dyes

Sustainable Conversion of Waste Carbon Brush and Fly Ash into a Novel Nanocomposite for Selective Adsorption of Cationic Dyes

Absorption and fluorescence spectroscopy of cold proflavine ions isolated in the gas phase.

Proflavine, a fluorescent cationic dye with strong absorption in the visible, has been proposed as a potential contributor to diffuse interstellar bands (DIBs). To investigate this hypothesis, it is essential to examine the spectra of cold and isolated ions for comparison. Here, we report absorption spectra of proflavine ions, trapped in a liquid-nitrogen-cooled ion trap filled with helium-buffer gas, as well as fluorescence spectra to provide further information on the intrinsic photophysics. We find absorption- and fluorescence-band maxima at 434.2 ± 0.1 and 434.7 ± 0.3nm, corresponding to a Stokes shift of maximum 48cm-1, which indicates minor differences between ground-state and excited-state geometries. Based on time-dependent density functional theory, we assign the emitting state to S2 as its geometry closely resembles that of S0, whereas the S1 geometry differs from that of S0. As a result, simulated spectra involving S1 exhibit long Franck-Condon progressions, absent in the experimental spectra. The latter displays well-resolved vibrational features, assigned to transitions involving in-plane vibrational modes where the vibrational quantum number changes by one. Dominant transitions are associated with vibrations localized on the NH2 moieties. Experiments repeated at room temperature yield broader spectra with maxima at 435.5 ± 1nm (absorption) and 438.0 ± 1nm (fluorescence). We again conclude that prevalent fluorescence arises from S2, i.e., anti-Kasha behavior, in agreement with previous work. Excited-state lifetimes are 5 ± 1ns, independent of temperature. Importantly, we exclude the possibility that a narrow DIB at 436.4nm originates from cold proflavine cations as the band is redshifted compared to our absorption spectra.

Comparative adsorption of cationic and anionic dye by using non-activated Black Plum seed biochar for aquatic phase: Isotherm, kinetic and thermodynamic studies

Industrial dye effluents play a major role in water pollution. Textile and leather industries are one of the important sectors that pollute the water by discharging many harmful cationic and anionic dyes during the dyeing process. This study aims to compare the dye removal efficiency of Black Plum seed biochar for the cationic and anionic dyes. The non-activated biochar was prepared through pyrolysis of Black Plum seed powder at 5700 C. The sample's surface chemistry was understood using various characterization techniques like Field Emission Scanning Electron Microscopy (FESEM), Energy-dispersive X-ray spectroscopy (EDS), Brunauer-Emmett-Teller (BET), X-ray diffraction (XRD), Raman-Spectroscopy and Zeta-potential. The experiments were successfully performed by conducting a batch adsorption study at different parameters such as pH, concentration, contact time and temperature. The coefficients of different isotherms and kinetics models were evaluated for non-linear study and the thermodynamic model was also applied. The maximum adsorption capacity was obtained as 42.39 mg/g for Crystal Violet (CV) dye and 6.22 mg/g for Eosin Blue (EB) dye by using the Langmuir isotherm model. Hence, the Black Plum seed biochar (BPSB) has superior adsorption capacity for the cationic dye CV ( removal - 98%) as compared to the anionic dye EB ( removal - 65%) at optimum parameters. Therefore, it is concluded that the BPSB is a natural toxin-free biosorbent and it can be used for the remediation of dyes from industrial wastewater.

Biochar from co-pyrolysis of biological sludge and woody waste followed by chemical and thermal activation: end-of-waste procedure for sludge management and biochar sorption efficiency for anionic and cationic dyes.

Nine biochars were produced by co-pyrolysis of sawdust and biological sludge following the "design of experiment" approach. Two kinds of sludge (both deriving from the treatment of mixed industrial-municipal wastewater) and two types of woody waste were selected as categorical predicting variables, while contact time, pyrolysis temperature, and sludge percentage were used as quantitative variables. Biochars were analysed for their product characteristics and environmental compatibility based on the European Standards (EN 12915-1:2009) for materials intended for water treatment (i.e. ash content, water leachable polycyclic aromatic hydrocarbons (PAHs) and elements), as well as for specific surface area (SSA), using them as response variables of a multivariate partial least square multiple regression, whose results provided interesting insights on the relationships between pyrolysis conditions and biochar characteristics. Biochars produced with sludge and/or providing the highest SSA values (258-370 m2g-1) were selected to undergo a sustainable chemical treatment using a by-product of the gasification of woody biomass, complying in all cases with European Standards and achieving therefore the end-of-waste status for sewage sludge. The biochar deriving from the highest percentage of sludge (30% by weight) and with the highest SSA (390 m2g-1) was thermally activated achieving SSA of 460 m2g-1 and then tested for the sorption of direct yellow 50 and methylene blue in ultrapure water and real wastewater, compared to a commercial activated carbon (AC). The biochar showed Langmuir sorption maxima (Qm) 2-9 times lower than AC, thus highlighting promising sorption performances. Qm for methylene blue in wastewater (28mg‧g-1) was confirmed by column breakthrough experiments.

An outstanding photocatalytic performance of CNTs based nanocomposite of ternary metal oxides towards cationic and anionic dyes and pharmaceutical drug

Currently, hetero-metallic oxides and their nanocomposites with 1D materials have a tremendous role in photocatalytic applications, mainly for the removal of organic effluents, due to their higher potential of electron-hole pair migration and separation than pure metal oxide NPs. The present work reports the fabrication of ternary metal oxides nanostructure (WO3·Ag2O·CuO) and its nanocomposite with carbon nanotubes (WO3·Ag2O·CuO/CNTs) using a facile approach i.e. ultra-sonication. The photocatalytic removal efficacy of fabricated nanocomposite i.e. WO3.Ag2O.CuO/CNTs along its counterpart (WO3·Ag2O·CuO) was evaluated using a model cationic dye (Methylene blue, MB), an anionic dye (Congo red, CR), and an analgesic drug (Paracetamol). The catalytic experiment was performed under natural sunlight upon light irradiation of about 90 min and using 30 mg of photocatalyst for all chosen effluents. The obtained results deduced that WO3·Ag2O·CuO/CNTs nanocomposite showed catalytic efficiency of about 97 % for MB, 87 % for CR, and 93 % for Paracetamol while it was about 80 % for MB, 74 % for CR, and 79 % for drug using WO3·Ag2O·CuO as photocatalyst. The rate constant values of nanocomposite for the removal of MB, CR, and Paracetamol are 0.037 min−1, 0.023 min−1, and 0.027 min−1 respectively. The remarkable degradation performance of WO3·Ag2O·CuO/CNTs nanocomposite as compared to ternary metal oxide (WO3·Ag2O·CuO) was due to its high charge separation, high surface area, and availability of large number of active sites for the adsorption of pollutant molecules. Hence, WO3·Ag2O·CuO/CNTs nanocomposite could be a competent photocatalyst for the removal of variety of industrial effluents i.e. organic dyes and pharmaceutical drugs etc.

Utilization of dried fruit peels from prickly pears as an eco-friendly bio-sorbent for adsorption and removing certain cationic dyes from water samples

Utilization of dried fruit peels from prickly pears as an eco-friendly bio-sorbent for adsorption and removing certain cationic dyes from water samples

Greenly synthesised novel microporous ZnO/GO for adsorption of methyl orange and malachite green

ABSTRACT This study presents a greenly synthesised novel nanocomposite composed of Zinc Oxide (ZnO) and Graphene Oxide (GO) for the adsorption of dyes from aqueous solutions. The nanocomposite was synthesised using algae thus representing a green and eco-friendly method, ensuring minimal environmental impact. The physical characterisation of zinc oxide and graphene oxide nanocomposite (ZnO/GO) was done using X-ray diffraction (XRD), Brunauer-Emmett-Teller (BET), Fourier transform infrared spectroscopy (FT-IR), Zeta Potential, and Particle Size Analyzer (PSA). The pore diameter of the ZnO/GO was 1.801 nm, and its total surface area was 54.062 m2/g. The nanocomposite’s adsorption performance was systematically investigated through batch adsorption experiments. With an adsorption efficiency of 296.73 mg/g and 259.74 mg/g for MO and MG, the Langmuir isotherm model outperforms the Freundlich isotherm model in terms of adsorption. The pseudo-second-order model having an R2 value of 0.99 for both MO and MG, offers a more convincing explanation of adsorption than the pseudo-first-order model. The results demonstrated rapid adsorption kinetics and high adsorption capacities for both cationic and anionic dyes. Additionally, the ZnO/GO has a high reusability without significant degradation. The sustainable nature of the nanocomposite was emphasised by its efficient dye removal, reusability, and minimal secondary waste generation.

A Sustainable Approach for Enhancing Cationic Dyes Adsorption in Single and Multiple Systems using Novel Nano Ferrites Modified with Walnut Shell

AbstractWalnut shell has been used in various experimental studies for different dyes removal, but it is exciting to study the adsorption behaviour of bio‐waste (walnut shell) in combination with spinel zinc ferrite which resulted in the formation of a novel material having magnetic properties and help in easy separation after the wastewater treatment. Novel magnetic walnut shell zinc ferrite (WSZF) composite has been synthesized and used to remove Malachite Green and Methylene Blue from aqueous solution in single and binary dye systems. Different techniques have been used to characterize the composite such as Fourier Transform Infrared Spectroscopy, X‐Ray Diffraction, Field Emission Scanning Electron Microscopy, Energy Dispersive Spectroscopy, Thermogravimetric Analysis and pHzpc. Adsorption of dyes were studied to see the effect of time, pH, adsorbent dose, dye concentration and temperature. The Lagergren pseudo second order model fitted well among various kinetic models employed. Langmuir adsorption isotherm best fitted with maximum adsorption capacities of 86.20 and 169.5 mg/g in single dye and 23.92 and 18 mg/g respectively in binary dye system for Malachite Green and Methylene Blue. Process was spontaneous and ΔH° were found positive, confirmed endothermic process of adsorption. The composite‘s regeneration capacity was studied for five cycles and at the end of five cycle the efficiency of the material was found to be around 80 % for both single as well as binary dye systems. It is concluded that the chosen WSZF will be the optimum solution for cationic dyes removal.

Blended Nephelium lappaceum and Durio zibethinus wastes for activated carbon production via microwave-ZnCl2 activation: optimization for methylene blue dye removal

Herein, this work targets to employ the blended fruit wastes including rambutan (Nephelium lappaceum) peel and durian (Durio zibethinus) seed as a promising precursor to produce activated carbon (RPDSAC). The generation of RPDSAC was accomplished through a rapid and practical procedure (microwave-ZnCl2 activation). To evaluate the adsorptive capabilities of RPDSAC, its efficacy in eliminating methylene blue (MB), a simulated cationic dye, was measured. The Box–Behnken design (BBD) was utilized to optimize the crucial adsorption parameters, namely A: RPDSAC dose (0.02–01 g/100 mL), B: pH (4–10), and C: time (2–6 min). The BBD design determined that the highest level of MB removal (79.4%) was achieved with the condition dosage of RPDSAC at 0.1 g/100 mL, contact time (6 min), and pH (10). The adsorption isotherm data is consistent with the Freundlich concept, and the pseudo-second-order versions adequately describe the kinetic data. The monolayer adsorption capacity (qmax ) of RPDSAC reached 120.4 mg/g at 25 °C. Various adsorption mechanisms are involved in the adsorption of MB dye onto the surface of RPDSAC, including π–π stacking, H-bonding, pore filling, and electrostatic forces. This study exhibits the potential of the RPDSAC as an adsorbent for removal of toxic cationic dye (MB) from contaminated wastewater.

ADSORPTION OF CATION DYE USING ACTIVATED CARBON DERIVED FROM GOLDEN SHOWERSEED POD ( C ASSIA FISTULA)

This study investigated the use of Golden shower seed pod (cassia fistula) as an adsorbent for the removal of cationic dye in a batch system. The raw material was Carbonized at 600 oC for one hour to obtain a purely carbonized material; then impregnated with NaOH of 0.1M and allowed to stay for 24 hours to obtain the desired GS-AC activated carbon. The adsorbent was characterized using scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, and energy-dispersive X-ray fluorescence (EDXRF) elemental composition analysis. The effects of adsorbent dosage and contact time on the adsorption process were studied in a batch system. The results revealed that, there was good enhancements in pores of the adsorbent GS-AC due to the chemical impregnation. The FTIR spectra showed the presence C-H, NH 2, C-O, and S=O functional groups indicating a favourable surface for adsorption. Batch studies indicated that, the methylene blue uptake decreased with increase in the GS-AC dosage. The amount of Methylene blue adsorbed onto GS-AC increased with time and subsequently remained constant at some point in time with maximum uptake at 500 mg/l. Thus, adsorption capacity of methylene blue increased with longer contact time, indicating a stronger interaction between the adsorbent and the dye. Based on the findings, Golden shower seed pod (cassia fistula) impregnated with NaOH can be used as an alternative and suitable material for cationic dye removal from liquid phase.

Competition between Transport and Recombination in Dye Solar Cells at Low Light Intensity

The efficiency of electron collection in a dye‐sensitized solar cell (DSC) is determined by a delicate balance between electronic transport and recombination losses caused by electron transfer to dye cations and electron acceptors. While state‐of‐the‐art DSCs have demonstrated quantitative electron collection under standard 1 sun conditions, the nonlinear nature of the trapping/detrapping dynamics in the photoanode with respect to the stored electronic charge can result in suboptimal performance under the low illumination intensity conditions commonly found indoors. Herein, the key factors influencing electron collection in relation to light intensity using impedance spectroscopy and numerical analysis are thoroughly examined. Impedance analysis reveals that the electron diffusion length tends to decrease as the quasi‐Fermi level is lowered, approaching the critical limit (Ln/d ≈ 1) at intensities characteristic of indoor illumination. A range of tert‐butyl pyridine concentrations and different thermal and chemical treatments of the TiO2 are tested, showing that this low intensity limitation is inherent to the multiple‐trapping mechanism that governs the functioning of a DSC. It is concluded that relatively high ideality factors, nonoptimal electrolyte compositions, or small variations in the quality of the TiO2 layer can result in electron collection limitations that are not apparent under 1 sun but become noticeable at low light intensities.

Supramolecular Gels Based on C3-Symmetric Amides: Application in Anion-Sensing and Removal of Dyes from Water.

We modified C3-symmetric benzene-1,3,5-tris-amide (BTA) by introducing flexible linkers in order to generate an N-centered BTA (N-BTA) molecule. The N-BTA compound formed gels in alcohols and aqueous mixtures of high-polar solvents. Rheological studies showed that the DMSO/water (1:1, v/v) gels were mechanically stronger compared to other gels, and a similar trend was observed for thermal stability. Powder X-ray analysis of the xerogel obtained from various aqueous gels revealed that the packing modes of the gelators in these systems were similar. The stimuli-responsive properties of the N-BTA towards sodium/potassium salts indicated that the gel network collapsed in the presence of more nucleophilic anions such as cyanide, fluoride, and chloride salts at the MGC, but the gel network was intact when in contact with nitrate, sulphate, acetate, bromide, and iodide salts, indicating the anion-responsive properties of N-BTA gels. Anion-induced gel formation was observed for less nucleophilic anions below the MGC of N-BTA. The ability of N-BTA gels to act as an adsorbent for hazardous anionic and cationic dyes in water was evaluated. The results indicated that the ethanolic gels of N-BTA successfully absorbed methylene blue and methyl orange dyes from water. This work demonstrates the potential of the N-BTA gelator to act as a stimuli-responsive material and a promising candidate for water purification.

Zinc oxide decorated plantain peel activated carbon for adsorption of cationic malachite green dye: Mechanistic, kinetics and thermodynamics modeling

Reports have shown that malachite green (MG) dye causes various hormonal disruptions and health hazards, hence, its removal from water has become a top priority. In this work, zinc oxide decorated plantain peels activated carbon (ZnO@PPAC) was developed via a hydrothermal approach. Physicochemical characterization of the ZnO@PPAC nanocomposite with a 205.2 m2/g surface area, porosity of 614.68 and dominance of acidic sites from Boehm study established the potency of ZnO@PPAC. Spectroscopic characterization of ZnO@PPAC vis-a-viz thermal gravimetric analyses (TGA), Fourier Transform Infrared Spectroscopy (FTIR), Powdered X-ray Diffraction (PXRD), Scanning Electron Microscopy and High Resolution – Transmission Electron Microscopy (HR-TEM) depict the thermal stability via phase transition, functional group, crystallinity with interspatial spacing, morphology and spherical and nano-rod-like shape of the ZnO@PPAC heterostructure with electron mapping respectively. Adsorption of malachite green dye onto ZnO@PPAC nanocomposite was influenced by different operational parameters. Equilibrium data across the three temperatures (303, 313, and 323 K) were most favorably described by Freundlich indicating the ZnO@PPAC heterogeneous nature. 77.517 mg/g monolayer capacity of ZnO@PPAC was superior to other adsorbents compared. Pore-diffusion predominated in the mechanism and kinetic data best fit the pseudo-second-order. Thermodynamics studies showed the feasible, endothermic, and spontaneous nature of the sequestration. The ZnO@PPAC was therefore shown to be a sustainable and efficient material for MG dye uptake and hereby endorsed for the treatment of industrial effluent.

A green and economic approach to synthesize magnetic Lagenaria siceraria biochar (γ-Fe2O3-LSB) for methylene blue removal from aqueous solution.

In the printing and textile industries, methylene blue (a cationic azo dye) is commonly used. MB is a well-known carcinogen, and another major issue is its high content in industrial discharge. There are numerous removal methodologies that have been employed to remove it from industrial discharge; however, these current modalities have one or more limitations. In this research, a novel magnetized biochar (γ-Fe2O3-LSB) was synthesized using Lagenaria siceraria peels which were further magnetized via the co-precipitation method. The synthesized γ-Fe2O3-LSB was characterized using FTIR, X-ray diffraction, Raman, SEM-EDX, BET, and vibrating sample magnetometry (VSM) for the analysis of magnetic properties. γ-Fe2O3-LSB showed a reversible type IV isotherm, which is a primary characteristic of mesoporous materials. γ-Fe2O3-LSB had a specific surface area (SBET = 135.30 m2/g) which is greater than that of LSB (SBET = 11.54 m2/g). γ-Fe2O3-LSB exhibits a saturation magnetization value (Ms) of 3.72emu/g which shows its superparamagnetic nature. The batch adsorption process was performed to analyze the adsorptive removal of MB dye using γ-Fe2O3-LSB. The adsorption efficiency of γ-Fe2O3-LSB for MB was analyzed by varying parameters like the initial concentration of adsorbate (MB), γ-Fe2O3-LSB dose, pH effect, contact time, and temperature. Adsorption isotherm, kinetic, and thermodynamics were also studied after optimizing the protocol. The non-linear Langmuir model fitted the best to explain the adsorption isotherm mechanism and resulting adsorption capacity ( =54.55mg/g). The thermodynamics study showed the spontaneous and endothermic nature, and pseudo-second-order rate kinetics was followed during the adsorption process. Regeneration study showed that γ-Fe2O3-LSB can be used up to four cycles. In laboratory setup, the cost of γ-Fe2O3-LSB synthesis comes out to be 162.75 INR/kg which is low as compared to commercially available adsorbents. The results obtained suggest that magnetic Lagenaria siceraria biochar, which is economical and efficient, can be used as a potential biochar material for industrial applications in the treatment of wastewater.

Determination of glycyrrhizic acid as sweeteners by dual-wavelength overlapping resonance Rayleigh scattering

This study used cationic dyes methyl violet (MV) and neutral red (NR) as probes, based on dual-wavelength overlapping resonance Rayleigh scattering (RRS), and designed two highly sensitive methods for the determination of the natural sweetener glycyrrhizic acid (GZA). In the Clark-Lubs buffer solution, when only MV or NR was present in the solution, they formed supramolecular polymers through hydrogen bonding. When adding GZA at different concentrations, the formation of ionic association complexes led to a subsequent decrease in RRS intensity at two wavelengths in the MV − GZA system and NR − GZA system, and the amount of the decline was proportional to the GZA concentration. The linear ranges were determined as 0.1 − 0.6 mg/L and 0.1 − 0.7 mg/L, with correlation coefficients of 0.9972 and 0.9996, and limits of detection were 0.052 mg/L and 0.016 mg/L, respectively. For this study, reaction conditions were optimized, potential interfering substances were investigated, and the mechanisms behind RRS generation and intensity decrease were discussed. The proposed methods were sensitive, fast, time-saving and efficient, and have been successfully applied to licorice and dried ginger decoction analysis, yielding satisfactory results.

Formation and catalytic potential of sheet like nanostructured amino functionalized graphene oxide Schiff's base immobilized by Cu nanoparticles in Click reaction, oxidation of fluorene and in photodegradation of methylene blue

A heterogeneous catalyst, environmentally benign, containing copper immobilized over amino functionalized Schiff's base graphene oxide was prepared. The prepared nanocatalyst was explored in various organic transformations such as in tri-azoles formation, in oxidation and the degradation of methylene blue. Click chemistry was employed in the formation of triazoles for the construction of carbon-heteroatom bonds which have many applications ranging from drug discovery to material science. Our present work focused on graphene-based nanocatalyst (Cu @NH2GO) which provided excellent efficiency and catalytic activity in carrying out organic transformations. The prepared nanocatalyst was characterized and examined by various spectroscopic techniques such as X-ray diffraction (PXRD), thermo gravimetric analysis (TGA), field emission-scanning electron microscopy (FE-SEM), EDX, high-resolution transmission electron microscopy (HR-TEM), Fourier transformer infrared spectroscopy (FT-IR), and X-ray Photoelectron Spectroscopy (XPS). TEM images showed the light grey sheets of silane functionalized Schiff's base on which Cu nanoparticles were immobilized. The catalyst was also explored for the degradation of methylene blue which provided an effective path for the treatment of wastewater. Methylene Blue is one of the environmentally persistent, carcinogenic and mutagenic cationic dyes. A large volume of methylene blue containing wastewater is discharged into groundwater or surface water. So it becomes necessary to degrade the toxic dye by the use of a prepared nanocatalyst (Cu @NH2GO). Moreover, the catalyst possesses excellent stability and reusability.