Calibration Chamber Research Articles

Experimental and Monte Carlo Evaluation of Spherical Ionization Chambers’ Response to 137Cs Radioactive Source

Measurements were performed for the calibration of an ionization chamber in the secondary standard dosimetry laboratory of IFIN-HH. A 10-liter spherical ionization chamber was calibrated using a 1-literspherical reference standard ionization chamber. The ionization chamber’s response to 137Cs was also evaluated computationally by MCNP and FLUKA Monte Carlo codes. The models of the experimental setup are validated and can be used for further studies, especially in cases where the real experiment is hard or impossible to perform

Application of high-sensitivity radon monitor on walk-in type radon calibration chamber at KRISS

This paper introduces the KRISS-Rn4, a high-sensitivity radon monitor with four detection cells, installed within a walk-in type radon calibration chamber at KRISS. The KRISS-Rn4 exhibits enhanced energy resolution through channel-by-channel signal processing and data acquisition. Results reveal that it achieves lower statistical fluctuations and faster response times in monitoring test atmospheres compared to commercial devices.

Commissioning and Assessment of Radiation Field and Dose Inhomogeneity for a Dual X-ray Tube Cabinet Irradiator: To Ensure Accurate Dosimetry in Radiation Biology Experiments

PurposeStandardization of X-ray cabinet irradiators dose, geometry, and calibration reporting is an ongoing process. Multi-tube designs have been introduced onto the pre-clinical market and give a theoretical benefit but have not been widely assessed for use in pre-clinical irradiation conditions. The aim of this study was to report on our experience commissioning a dual x-ray source cabinet irradiator (CIXD, Xstrahl Limited, United Kingdom) and assess the dose distribution for various experimental conditions. Materials and MethodsHalf-value layer (HVL) measurement, profile measurements, and output calibration were performed with a calibrated ion chamber. Constancy measurements were performed twice daily over two weeks to assess output fluctuations. Film measurements were completed using solid water to assess percent depth dose and homogeneity within the field and within variable thickness of solid water and phosphate-buffered saline (PBS) solution. Film measurements were repeated for various arrangements of petri dishes filled with PBS or water and in a 3D printed mouse phantom. ResultsThe X-ray tubes measured in-air output was 1.27 Gy/min. The HVL was 1.7 mm Cu. The upper and lower tubes both exhibited the heel effect, but when operated simultaneously the effect was reduced. Ion chamber measurements revealed 15% dose inhomogeneity within the tray area (18 × 18 cm2). Film measurements in the petri dishes indicated minor non-uniformities with the arrangements of experimental apparatus. The mouse phantom with film agreed with ion chamber measurements for various phantom placement and orientations. ConclusionX-ray cell culture irradiation with the dual tube cabinet irradiation is efficient and robust when utilizing established dosimetric tools to confirm output and homogeneity. The conditions assumed for calibrations are often not maintained during experiments. We have confirmed that inhomogeneities are present for single tube use, however they are reduced with simultaneous tube use. Additional dosimetric monitoring should be performed for each unique irradiation setup.

Large-chamber reciprocity calibration for microbarometers

The Penn State Applied Research Laboratory (PSU) and Sandia National Laboratories (SNL) have implemented a reciprocity-based primary calibration technique in SNL’s infrasound calibration chamber. The goal in this work is primary calibration of microbarometers from 0.01 to 10.0 Hz. The National Center for Physical Acoustics at the University of Mississippi designed and built the chamber, which SNL has modified and currently operates. This chamber incorporates two moving coil loudspeakers capable of operating in receive and transmit mode. PSU developed the calibration technique and the required electronics to take advantage of these two reciprocal loudspeakers, while SNL installed this hardware and made the required test measurements. Because the chamber is large (1400 l), the chamber volume dominates the acoustical admittance thereby reducing the dependence of the calibration on the physical characteristics of the loudspeakers and reducing calibration uncertainty. However, laboratory tests have found increased uncertainty at very low frequencies ( < 0.05 Hz). This is due to reduced loudspeaker response and increasing noise within the chamber at these frequencies. This talk will discuss the large-chamber reciprocity method, important considerations for reducing uncertainty in this implementation, and limitations of this method.

Cavity expansion-based interpretation of piezocone penetration test (CPTu) data in clays

A cavity expansion-based method is proposed in this paper to correlate the relevant findings with the piezocone penetration test (CPTu) data in clays. The rigorous and explicit solution for both spherical and cylindrical undrained cavity expansion is adopted based on a unified critical state constitutive model for clays and sands. The analogous model developed is comprehensively validated against two series of advanced numerical simulations and calibration chamber tests of the CPTu in fine-grained soils, along with bias analyses. The effects of the overconsolidation ratio and initial state parameter are extensively investigated for various clay types. Both theoretical and empirical correlations are then proposed for back-calculations of cone factor, undrained shear strength, overconsolidation ratio and initial state parameter of clays. Two case studies of CPTu tests are conducted in addition to examine correlations and contours of the in situ state parameter, demonstrating the applicability of the proposed theoretical approach for interpretation of the CPTu data.

Standard technical specifications for methacholine chloride (Methacholine) bronchial challenge test (2023)

Standard technical specifications for methacholine chloride (Methacholine) bronchial challenge test (2023)

Intraoperative radiation therapy with 50kV x-rays: A multi-institutional review.

This report covers clinical implementation of a low kV intraoperative radiation therapy (IORT) program with the INTRABEAM® System (Carl Zeiss Meditec AG, Jena, Germany). Based on collective user experience from eight institutions, we discuss best methods of INTRABEAM quality assurance (QA) tests, commissioning measurements, clinical workflow, treatment planning, and potential avenues for research. The guide provides pertinent background information and clinical justification for IORT. It describes the INTRABEAM system and commissioning measurements along with a TG100 risk management analysis to ensure safety and accuracy of the IORT program. Following safety checks, dosimetry measurements are performed for verification of field flatness and symmetry, x-ray output, and depth dose. Also discussed are dose linearity checks, beam isotropy, ion chamber measurements, calibration protocols, and in-vivo dosimetry with optically stimulated luminescence dosimeters OSLDs, and radiochromic film. Emphasis is placed on the importance of routine QA procedures (daily, monthly, and annual) performed at regular intervals for a successful IORT program. For safe and accurate dose delivery, tests of important components of IORT clinical workflow are emphasized, such as, dose prescription, pre-treatment QA, treatment setup, safety checks, radiation surveys, and independent checks of delivered dose. Challenges associated with in-vivo dose measurements are discussed, along with special treatment procedures and shielding requirements. The importance of treatment planning in IORT is reviewed with reference to a Monte Carlo-based commercial treatment planning system highlighting its main features and limitations. The report concludes with suggested topics for research including CT-based image-guided treatment planning and improved prescription dose accuracy. We hope that this multi-institutional report will serve as a guidance document on the clinical implementation and use of INTRABEAM IORT.

Numerical modeling of open-ended piles

Deep foundations are generally used when significant loads are applied, and the site conditions do not allow for the implementation of soil reinforcement processes. This research focuses on studying the behavior of piles in a frictional environment, used as foundations for offshore structures in dense sands, involving anchor depths and overloads significantly higher than those encountered in onshore applications. The bearing capacity of open-ended driven piles plays a crucial role in this study. Therefore, a series of tests were conducted in the literature on model piles in a calibration chamber, which is considered a tool for physical modeling, allowing for significant penetration of instrumented model piles under confinement conditions similar to those experienced by real piles. Emphasis is placed on predicting the ultimate load capacity of open-ended piles using numerical methods. Calculations were performed using the finite element code PLAXIS to numerically reproduce the same shear stresses as those measured on the model during various phases of the experiment. The approach aims to validate the documented experiments in the literature and compare the ultimate load capacity of an open-ended pile to that of a closed-ended pile. Our study is limited to the case of a single pile, subject to static and axial force. The results show that it is possible to achieve a good agreement between the experiment and the numerical modeling with a relatively simple model, provided that the soil parameters are chosen correctly and the interface stiffness is adequately simulated.

PM1, PM2.5 and PM10 size fraction distribution under steady-state conditions in a walk-in type 222Rn calibration chamber facility.

Attachment of 222Rn progenies, upon their formation, to the atmospheric aerosols and inhalation of these radioactive aerosols causes inhalation dose to the human being. Aerosols have the characteristics of small particle size, long-time suspension and long-distance transmission and easy access to the deep respiratory tract. Aerosols are responsible for viral infection risk such as the recent worldwide pandemic caused by severe acute respiratory syndrome coronavirus-2 (SARS-CoV-2, or COVID-19). Understanding the formation and behaviour of aerosols in a confined environment in various human habitations is essential to combat such detrimental exposures. Experiments have been performed to study the distribution of aerosol size fractions in the walk-in type 222Rn calibration chamber. The real-time applied particle technology monitors (APT-Maxima stationary monitors) were used for the simultaneous measurements of PM1, PM2.5, and PM10 size fractions. The variation of the mass densities (μgm-3) of different size fractions at different positions inside the chamber was monitored by placing APTs. The PM1, PM2.5, and PM10 sizes fractions were distributed homogeneously within the chamber volume and the concentration ratios of these fractions were 1:1.5:1.6 for concentration values of < 1500μgm-3, and 1:7:9 for the concentration values of > 1500μgm-3.

Material point method simulations of displacement pile and CPT penetration in sand considering the effects of grain breakage

Full displacement installation dramatically alters the stress and strain fields applying around piles and Cone Penetrometer (CPT) probes at sand sites. Calibration chamber tests have indicated that severe particle crushing occurs near to the pile or cone tips and a distinct shear zone may develop that leaves crushed sand adhering to the pile or cone shaft. It is therefore important to investigate how particle breakage affects the stress and deformation fields developed as this process occurs. In this study, installation by monotonic jacking of conically tipped model piles or CPT probes into silica sand is simulated by material point method (MPM) analyses. A thermodynamically consistent model which considers competing grain crushing and dilation is employed to model the sand behavior, while an MPM approach is adopted to cater for the large deformations involved in the penetration process. Particle crushing is predicted beneath the pile tip and around the pile shaft. The numerical results are compared to directly related instrumented pile calibration chamber tests. The numerical results show that the computed stress and displacement fields match key aspects of the experimental results well, especially in reproducing the volumetric compression observed experimentally. The results confirm that combining MPM with suitably sophisticated constitutive models creates new capabilities for analyzing large-deformation problems.

Design of Incu Analyzer for IOT based Baby Incubator Calibration (Chamber Temperature)

Incubator Analyzer is a calibration tool used to measure temperature, mattress temperature, humidity, airflow, and sound level in baby incubators. The purpose of this research is to make a tool "Design of Incu Analyzer for IOT based Baby Incubator Calibration (Chamber Temperature)” with LCD display and Thingspeak. The design of this calibration tool consists of baby incubator chamber temperature parameters consisting of 5 points, namely T1, T2, T3 , T4, T5 using the DS18B20 sensor and using the ESP32 microcontroller to take advantage of the IOT system. Utilization of IOT on ESP32 is using Wi-Fi. The ESP32 microcontroller processes data from the DS18B20 temperature sensor which is then displayed on the LCD display and Thingspeak. Testing of this tool is done by comparing incubator analyzer module with a standard measuring instrument, INCU II. In this study, the temperature parameter obtained the smallest error value of -0,059293% at T5 with a setting temperature of 36°C and the largest error value of -0,0254188% at T2 with a setting temperature of 35°C. Overall the conclusions obtained after carrying out the literature study process, and planning, it can be concluded that the tool "Incu Analyzer Design for IOT based Baby Incubator Calibration" can be used according to the plan, namely Incubator Analyzer with IOT based.

Dominant factors in MiniCone, CPT and pile correlations: A data‐based approach

AbstractThe cone penetration test (CPT) contributes to the design and analysis of piles regarding geometry, installation effect, and pile capacity (shaft and toe resistance). MiniCone, as an alternative to CPT sounding, has been used to carry out field and laboratory investigations by physical modeling. More tests can be practically carried out through light equipment and small soil mass, involving fewer errors caused by boundary conditions. Furthermore, it can be used for in situ testing, such as quality control, assessment of ground improvement, and subgrade characterization. A database comprising MiniCone and CPT records in field and physical modeling is proposed with a variety of cone diameters. The case study records in the database have been obtained from 140 tests compiled from data from 26 sources. The sources include the results of 20 physical modelings and field data from six sites in 10 countries. The data comprise MiniCone and CPT cone tip resistance (), and sleeve friction (). The different cones are used in sandy, silty sand, and clayey soils via simple chambers (1 g), calibration chambers, and frustum confining vessels. In addition, correlations were found in penetration records in terms of physical modeling types, cone diameters, penetration rates, and soil densities. Moreover, and are related to capacities of pile toes and shafts using proper correlation coefficients less than unity, respectively. Correlations and dominant factors in geotechnical practice between MiniCone, CPT, and pile have been reviewed and discussed.

Commissioning and Assessment of Radiation Field and Dose Inhomogeneity for a Dual X-Ray Tube Cabinet Irradiator: To Ensure Accurate Dosimetry in Radiation Biology Experiments

Standardization of X-ray cabinet irradiators calibration and dose reporting is an ongoing process. Multi-tube designs have been introduced and provide theoretical benefit but have not been assessed for pre-clinical irradiation conditions. This study was to report our experience commissioning a dual x-ray tube cabinet irradiator and assess dose distribution for various conditions. Homogeneity and percent depth dose (PDD) of various tube designs in single-tube setting have been previously reported, however multi-tube designs can overcome field asymmetry caused by the heel effect and improve dose fall-off at depth. Profile measurements and output calibration were performed with a calibrated ion chamber. We measured the percent-depth-dose (PDD) with film for each tube individually (PDDind) and both tubes simultaneously (PDDsim). To replicate conditions similar to petri dishes, we evaluated the range of attenuation and scatter under variable solid water thickness up to 9 mm with 3 mm build-up below (i.e., 1.2 cm total backscatter) under several geometries. The films were placed at a fixed position with variable amount of solid water placed above the film. We measured the output with variable water volumes with a 6 cm petri dish to simulate variable solution volumes that are frequently used during in vitro experiments. Film was also placed in a 3D printed mouse phantom with dimensions of (9.5 × 3.6 × 3.0 cm) and constructed to be roughly cylindrical. The dose in the 20 × 20 cm2 tray was within 8.4% of the central axis dose with both tubes. Dose rates decreased at the furthest points on the tray, but remained within 5% within the 15 × 15 cm2 central area. PDDsim with total 7.9 cm backscatter shows that the output is within 95% of the maximum dose at 4 cm depth. PDDsim with 1.2 cm backscatter is also within 95% of the maximum. The PDDind was less than 90% at 1.8 cm, which is similar to other single-tube systems. Slight increase in dose was seen with increasing solution; however, the doses were within 7% of the measured max dose at 6.3 mm depth. This agrees well with the solid water measurements. The results for both solid water and petri dish with variable medium is shown in Table 1. The 3D printed mouse phantom profiles for each plane showed results consistent with the ion chamber measurements. X-ray cell culture irradiation with dual-tube cabinet irradiation is robust when utilizing established dosimetric tools to confirm output and homogeneity. The conditions assumed for calibrations are often not maintained during experiments. We have confirmed that inhomogeneities are present for single tube use, however they are reduced with simultaneous tube use. Additional monitoring should be performed for each unique irradiation setup.

Study on the Characteristics of Effective Internal Friction Angles of Silty Clay from the Yellow River Delta and the Inverse Method of CPTu Testing

This study focuses on the silty clay of the Yellow River Delta, conducting laboratory experiments to explore the strength characteristics of typical silty clay in the Yellow River Delta. The study utilizes CPTu calibration chamber tests to systematically reveal the features of cone tip resistance (qt), side friction resistance (fs), and pore water pressure (u2) of the silty clay. This research provides a theoretical basis for Delta investigation in the Yellow River region. The study compares the applicability of existing CPTu inversion methods and highlights the NTH method’s advantages in evaluating silty clay’s effective internal friction angle. Supported by indoor calibration chamber tests, the study confirms the reliability of the NTH method in estimating the effective internal friction angle under normally consolidated conditions while also identifying its limitations. These research findings offer data support for the in situ rapid and accurate estimation of design parameters, like the internal friction angle and undrained shear strength of the silty clay in the Yellow River Delta. Moreover, they provide insights for obtaining other crucial in situ data.

Primary activity standardization of 18F for the calibration of the KRISS ionization chamber

Primary activity standardization of 18F for the calibration of the KRISS ionization chamber

Development of a thoron calibration chamber based on computational fluid dynamics simulation and validation with measurements

Recently, interest in measuring the concentration of 220Rn in air has increased greatly following the development of standards and the calibration of monitoring instruments. In this study, a 220Rn calibration chamber was designed and developed at the Institute of Radiochemistry and Radioecology (RRI) based on the computational fluid dynamics (CFD) method implemented in ANSYS Fluent 2020 R1 code at the University of Pannonia in Hungary. The behavior of 220Rn and its spatial distribution inside the 220Rn calibration chamber at RRI were investigated at different flow rates. The 220Rn concentration was close to homogeneous under higher flow regimes due to thorough mixing of the gas inside the chamber. Predictions based on CFD simulations were compared with experimentally measured transmission factors (Cout/Cin). The spatial distribution of 220Rn was dependent on the flow rate and the positions of the inlet and outlet. Our results clearly demonstrate the suitability of the 220Rn calibration chamber at RRI for calibrating monitoring instruments. Furthermore, the CFD-based predictions were in good agreement with the results obtained at higher flow rates using experimental and analytical models according to the relative deviation, with a maximum of approximately 9%.

Loading-unloading of spherical and cylindrical cavities in cohesive-frictional materials with arbitrary radially symmetric boundary conditions

Many scenarios in geotechnical engineering involve cavity unloading from a loaded state under different boundary conditions, especially for thick-walled cylinder tests in laboratory conditions. A novel analytical cavity expansion-contraction solution is proposed for modeling thick-walled cylinder tests during a complete loading-unloading process under arbitrary symmetric boundary conditions. The proposed solution has potential implication in investigating ambiguous boundary effects for problems involving cavity expansion-contraction. The mechanical model considers two concentric layers of materials around the cavity, where the inner layer is considered as cohesive-frictional and the circumambient infinite layer is assumed as elastic to simulate the arbitrary radially symmetric boundary condition, including two extreme scenarios with constant-pressure and zero-displacement boundaries. The derived solution provides the evolutions of cavity pressure and distributions of stresses and displacements in both layers during the loading-unloading process, which is then rigorously validated against finite element results. The effects of boundary conditions and size of the cohesive-frictional layer have been comprehensively investigated by analyzing the cavity pressure and the developments of plastic zones during expansion and contraction. The developed solution has been proved to be applicable in geotechnical engineering, with comparisons between analytical results and experimental data for pressuremeter tests in calibration chambers and pile installation tests in a rigid container. The proposed solution might also be helpful in the analysis of autofrettaged pressure vessels.

An experimental study of Horizontal Directional Drilling (HDD) in sand in a large flexible calibration chamber

Horizontal Directional Drilling (HDD) is a trenchless technique for underground infrastructure installation that uses pressurized drilling fluid. Excessive loss of fluid to the formation can cause problems not only for the execution of HDD but also to nearby structures and must, therefore, be avoided. Hydraulic fracture is one of the possible causes and theories to predict the ultimate pressure have been developed, mostly for clays. Luger and Hergarden (1988, apud Keulen, 2001) developed a hydraulic fracture model particularly for HDD. The present study presents an experimental program carried out on a large flexible calibration chamber in sand using drilling fluid and confining pressures compatible with HDD field conditions. Results show that while local fracturing may occur, causing injection pressure to decrease for a while, permeability is still the dominating factor.

DEM analysis of crushing evolution in cemented granular materials during pile penetration

The present study demonstrates that the 3D discrete-element method provides a practical model approach to visualize the cemented grain crushing evolution under pile penetration. A combined method using a rigorous breakage criterion based on octahedral shear stress (OSS) was implemented in the particle flow code PFC3D. First, the pile penetration is simulated by considering the grains as uncrushable with a screening of highly stressed grains exceeding the threshold defined by the OSS failure condition. Then, the simulation is repeated where crushable agglomerates replace the highly stressed grains. This method is more accurate than the replacement method and more efficient than the agglomerate method. A quarter of the numerical model was considered after validation to achieve an acceptable computational time for parametric studies. Parametric investigations were performed on the effects of particle crushing, boundary conditions, pile tip shape, and pile penetration velocity on the penetration resistance behavior. In agreement with the observations of the physical calibration chamber, the present results indicate that the proposed modeling approach is reliable in reproducing the concentration of crushed granular material particles in the vicinity of the pile tip and shaft. In addition, grain crushing has been found to reduce both penetration and shaft resistance.

Calibration of a Micromegas-based gaseous time projection chamber using cosmic ray muons

We report the calibration of a gaseous Time Projection Chamber based on Micromegas charge readout modules with cosmic ray muons, utilizing their penetrating power and relatively uniform energy deposition per unit length. Muon events were selected through track reconstruction to characterize detector performances, such as the drift velocity, electron lifetime, detector gain, and electric field distortion. The evolution of detector performances over a 50-day data-taking cycle was measured with the muon calibration method. For instance, the drift velocity degraded from 3.40 ± 0.07 cm/μs to 3.06 ± 0.06 cm/μs without gas purification, and then recovered with gas purification. A 137Cs calibration source was also placed inside the detector as a reference for muon calibrations.