Behaviour Of Materials Research Articles

Retrofitting Shear Critical Beams using Ultra High Performance Fibre Reinforced Concrete (UHPFRC)

Ultra High-Performance Fiber Reinforced Concrete (UHPFRC) is a cementitious composite that exhibits superior mechanical properties, durability, fire resistance, abrasion resistance, and chloride penetration. The enhanced performance of UHPFRC is attributed to the presence of highstrength steel fibers. Therefore, UHPFRC is widely used in structural retrofitting and rehabilitation works to improve the load carrying capacity of deteriorated structural members. This paper investigates the behaviour of UHPFRC retrofitted shear critical reinforced concrete beams. Numerical models were developed to simulate how the load-carrying capacity of UHPFRC retrofitted shear critical beams is influenced by factors such as jacket configuration, jacket thickness, and jacket length along the beam. Numerical models were validated using pre-existing experimental results. A modified Concrete Damage Plasticity (CDP) model was employed to simulate the material behaviour of UHPFRC. The validated numerical model was employed to perform parametric studies to examine the behaviour of UHPFRC retrofitted beams. It was observed that the modified CDP model effectively predicted the UHPFRC behaviour. Further, the results indicated that the application of UHPFRC retrofitting converted the brittle shear failure of shear-critical reinforced concrete beams into flexure failure. Moreover, the load carrying capacity of retrofitted beams increased with the retrofitted UHPFRC jacket thickness.

Correlation of fabric parameters and characteristic features of granular material behaviour in DEM in constitutive modelling

AbstractThe anisotropic microstructure of granular materials has a profound effect on their macroscopic behaviour and can be characterised using a fabric tensor. To include of fabric in the critical state theory (CST), anisotropic critical state theory (ACST) was proposed by modifying the state parameter $$(\psi )$$ ( ψ ) of CST to a fabric-dependent dilatancy state parameter $$(\upzeta )$$ ( ζ ) . Noteworthy that $$\uppsi$$ ψ showed a very strong correlation with characteristic features (e.g. instability, phase transformation and characteristic state) of macroscopic behaviour and, as a result, it has been adopted in many constitutive models. While $$\upzeta$$ ζ aided the inclusion of fabric in ACST models, the correlation between $$\upzeta$$ ζ and characteristic features has not been evaluated in detail yet, although a large number of works are found on micromechanics and fabric only. In this study, a large number of discrete element method simulations for drained and undrained triaxial were conducted to evaluate the correlation between $$\upzeta$$ ζ and characteristic features. To this purpose, the correlation between stress ratio and both classic and dilatancy state parameter ($$\psi$$ ψ and $$\upzeta$$ ζ ) were studied in important characteristic features (e.g. instability, phase transformation and characteristic state). It was found that this correlation was improved using $$\upzeta$$ ζ which might be due to the inclusion of fabric in our model. This observation is new and significant for inclusion of fabric evolution in constitutive modelling.

Preconditioning of mountain permafrost towards degradation detected by electrical resistivity

Warming permafrost has been detected worldwide and is projected to continue during the next century by many modelling studies. In mountain regions, this can lead to potentially hazardous impacts on short time-scales by an increased tendency for slope instabilities. However, time scales of permafrost thaw and the role of the ice content are less clear, especially in heterogeneous mountain terrain, where ice content can vary between zero and supersaturated conditions over small distances. Warming of permafrost near the freezing point shows therefore complex inter-annual behaviour due to latent heat effects during thawing and the influence of the snow-cover, which is governed by highly non-linear processes itself. Here, we demonstrate a preconditioning effect within near-surface layers in mountain permafrost that causes non-linear degradation and accelerates thaw. We hypothesise that a summer heat wave, as has occurred in the Central European summers 2003, 2015 and 2022, will enhance permafrost degradation if the active layer and the top of the permafrost layer are already preconditioned, i.e. have reduced latent heat content. This preconditioning can already be effectuated by a singular warm year, leading to exceptionally strong melting of the ground ice. On sloping terrain this ice-loss can be considered as irreversible, as large parts of the melted water will drain during the process, and an equivalent build-up of ice in cold years does not happen on similar time-scales as the melting. We propose a simple geophysical approach based on electrical resistivity tomography surveys that can assess the state of preconditioning in the absence of boreholes. In addition, we will show that resistivity data from a total of 124 permafrost sites in the Andes, Europe, and Antarctic adhere to a distinct power law behaviour between unfrozen and frozen states, which confirms the consistent electrical behaviour of permafrost and active layer materials over a wide range of landforms and material composition.

The effect of pressure on the thermodynamic properties of hydrogenic impurity in the GaAs semiconductor quantum well

ABSTRACT Studying the thermodynamic properties of hydrogen impurity in low-dimensional nanostructures under high-pressure environment is crucial for understanding the optical property and thermal excitation behaviour of semiconductor material. Here, we extensively explore the effect of pressure on thermodynamic properties, specifically, the average energy, free energy, entropy, and heat capacity of one-dimensional (1-D) hydrogenic impurity in GaAs semiconductor quantum well. Our findings reveal some novel phenomenon in the thermodynamic properties of hydrogenic impurity as pressure increases in the GaAs quantum well. Remarkably, at a constant temperature, both the average energy and free energy of hydrogenic impurity decrease as pressure rises, while entropy increases with increasing pressure. Intriguingly, the heat capacity shows distinct behaviour with varying pressure for different sizes of the quantum well. For very small size of the quantum well, the heat capacity increases with increasing pressure. However, for larger size of the quantum wells, the variation of heat capacity with pressure becomes irregular, showing a changeover from an increase to a decrease in response to increasing pressure. This research presents a pioneering method that employs pressure as a versatile tool for modulating the thermodynamic properties of hydrogenic impurity states in the nanostructures, and has some guidance for the preparation and synthesis of semiconductor devices.

Mechanical and fracture properties of mortars reinforced with glass fibre and prepared with different cement types

PurposeThe main aim of the current study is to investigate the effect of Anti-Crack HP 67/36 glass fibre on the mechanical performance of mortars made of cement, with a focus on post-cracking evaluations using the digital image correlation (DIC) technique.Design/methodology/approachExperimental tests were carried out on 36-mm long fibres at 0.8% by volume and added to the normal strength (NSM), high strength (HSM) and high strength mortar with fly ash (HSMFA) mortars. CEM I 52.5 CP2 NF, CEM II/A-L 42.5 NF and CEM III/C 32.5 N-SR PM were used for each series of mortar to assess the performance of the glass fibres with the types of cement. F-class fly (FA) ash was used to reduce global CO2 emissions.FindingsThe mortar’s strength decreased as the cement types changed from CEM I to CEM II and III. However, due to changes in the portlandite content of the cement, water porosity increased for both types of mortar, without and with fibre. It was also found that using glass fibre increased flexural strength more than compressive strength, regardless of the type of cement used. For all the strength classes, it was found that the mortar mixes with CEM I had the highest critical crack opening (wc) and fracture energy (GF), followed by CEM II and III. No significant effects were observed in the mortar’s property by replacing fly ash (12%).Research limitations/implicationsOnly mortars were formulated in this study, but the results must be verified at the concrete scale.Practical implicationsValidation of the DIC technique to characterize the post-cracking behaviour of cement-based material. Use of glass fibres to improve the material’s resistance to cracking.Social implicationsUse of CEM II and CEM III cements with low CO2 footprint instead of CEMI without altering the mechanical performance of the material.Originality/valueThe work is a further contribution to studying the cracking behaviour of several series of variable mortars depending on the resistance class and the type of cement used.

Contact-angle hysteresis on rough surfaces: mechanical energy balance framework

Using as a starting point conservation of momentum, a multiphase mechanical energy balance equation is derived that accounts for multiple material phases and interfaces present within a moving control volume. This balance is applied to a control volume that is anchored to a three-phase contact line as it advances continuously over the surface of a rough and chemically homogeneous and inert solid. Using semi-quantitative models for the material behaviour occurring within the control volume, an order of magnitude analysis is performed to neglect insignificant terms, producing an equation for predicting contact-angle hysteresis from a knowledge of the interface dynamics occurring around the three-phase contact line. It is shown that the viscous energy dissipation that occurs during the ‘stick–slip’ motion of the three-phase contact line, being the cause of contact-angle hysteresis on rough surfaces, can be calculated from changes in intermediate equilibrium interface states. The balance is applied to the Wenzel, Cassie–Baxter and Fakir (super-hydrophobic) wetting states, showing for the Fakir case that significant dissipation occurs during both interface advance and recede, and relating these dissipations to interfacial area changes that occur around the ‘stick–slip’ events.

Thermomechanical constitutive behaviour of 3D printed biomimetic polymer material under high strain rates

With the continuous technical breakthroughs of flexible electronics, materials with outstanding application potential are constantly being designed and optimized. Biomimetic polymer materials are particularly appealing due to their versatility and ease of fabrication, but their mechanical reliability, particularly their thermomechanical constitutive behavior under extreme working loads, remains unclear. In this paper, the impact responses of a 3D printed biomimetic polymer material named “Tangoblack” are investigated under thermomechanical, focusing on the effect of strain rate. By adjusting the pressure of the gas gun in the split Hopkinson pressure bar, different strain rates are achieved, while the high temperature of the tested sample can be controlled using a heating furnace integrated into the experiment system. Materials for pulse shapers are carefully selected to ensure longer durations at nearly constant strain rates. The constitutive behaviour of the biomimetic polymer material is further investigated under a wide strain rate range from 958 s-1 to 2158 s-1 and three different temperatures (20 °C, 70 °C and 120 °C). The results demonstrate a significant dependence of the polymer material on both strain rate and temperature. A rapid increase in forming strain rate enhances the strain hardening process, while simultaneously revealing a substantial temperature softening effect. Then, an improved nonlinear thermoviscoelastic ZWT constitutive model is proposed utilizing the Vogel-Fulcher-Tammann equation and implemented as a user-defined material model in ABAQUS/Explicit. The proposed constitutive model is demonstrated to be distinctly advantageous, which suggests a novel pathway for describing the mechanical reliability of biomimetic polymer materials under extreme working conditions.

Direct FE[formula omitted] failure prediction of fused-filament fabricated parts

The rapid development of additive manufacturing (AM) technology and the consequential microstructural variations have brought the simulation aspects into focus. To capture an accurate mechanical response, multiscale methods are used to determine the macroscopic constitutive behaviour. Among these methods, the recently introduced Direct FE2 (DFE2) technique has shown some success in predicting material behaviour via the direct incorporation of representative microstructure volumes into the macroscopic structure. The present study highlights the predictive modelling capabilities of DFE2 linked with an element elimination technique (EET) in investigating the performance of fused filament fabrication (FFF) samples under tension and compression. Parts were manufactured by FFF with various raster angles to vary the failure characteristics. Their mechanical responses and fracture behaviours were simulated by DFE2 and benchmarked against conventional FE, highlighting that the results of DFE2 were competitive against FE. Most importantly, the combination of EET with DFE2 resulted in predictive insights regarding changes in the failure surface for samples with varying raster angles.

Evaluation of self-sensing material behaviour: Insights from cyclic and pulse load testing

Recent advancements in materials engineering have addressed challenges in integrating sensory properties into metallic components, notably through Self-Sensing Materials (SSMs) embedding piezoelectric particles like Barium Titanate (BT) via Friction Stir Processing (FSP). This study explores self-monitoring metallic parts obtained by incorporating BT particles in AA5083-H111 plate via FSP, evaluating their behaviour under cyclic and pulse loads for real-time operational insights. The study explores how manufacturing processes affect SSMs’ electrical voltage response, focusing on FSP’s impact on different nugget regions, investigating polarization direction, electrode positioning, thickness effects, and performance under pulse loads. Findings indicated consistent electrical responses across specimens, with sensitivity affected by polarization direction and thickness. There was no evidence of electrical voltage response for constant loads. The pulse and cyclic loads triggered an electrical response, exhibiting a piezoelectric behaviour. The study highlights the intricate relationship between specimen features and piezoelectric properties, offering insights into optimizing SSM performance.

Hygrothermal Properties and Performance of Bio-Based Insulation Materials Locally Sourced in Sweden.

In recent years, there has been a paradigm shift in the building sector towards more sustainable, resource efficient, and renewable materials. Bio-based insulation derived from renewable resources, such as plant or animal fibres, is one promising group of such materials. Compared to mineral wool and polystyrene-based insulation materials, these bio-based insulation materials generally have a slightly higher thermal conductivity, and they are significantly more hygroscopic, two factors that need to be considered when using these bio-based insulation materials. This study assesses the hygrothermal properties of three bio-based insulation materials: eelgrass, grass, and wood fibre. All three have the potential to be locally sourced in Sweden. Mineral wool (stone wool) was used as a reference material. Hygrothermal material properties were measured with dynamic vapour sorption (DVS), transient plane source (TPS), and sorption calorimetry. Moisture buffering of the insulation materials was assessed, and their thermal insulation capacity was tested on a building component level in a hot box that exposed the materials to a steady-state climate, simulating in-use conditions in, e.g., an external wall. The tested bio-based insulation materials have significantly different sorption properties to stone wool and have higher thermal conductivity than what the manufacturers declared. The hot-box experiments showed that the insulating capacity of the bio-based insulators cannot be reliably calculated from the measured thermal conductivity alone. The results of this study could be used as input data for numerical simulations and analyses of the thermal and hygroscopic behaviour of these bio-based insulation materials.

Non-destructive evaluation of the steel fibre content and anisometry in thin UHPFRC elements

The tensile response of ultra-high performance fibre-reinforced composites (UHPFRC) is decisive in many applications and depends on the steel fibre content and orientation. These vary troughout the structural element and may differ from those in the laboratory specimens used to characterize the material behaviour. This work presents the developments on a non-destructive test method based on the measurement of the magnetic inductance, substantiating its use for the determination of the fibre content and orientation in thin UHPFRC elements and allowing the estimation of the directionally dependent post-cracking tensile strength of the material in the structure. Starting from a probabilistic description of the fibre orientation, an existing physical model of the magnetic circuit composed of a U-shaped inductor and the composite is generalized and is used to derive the relations between the magnetic inductance measurements, the fibre volumetric fraction and the fibre orientation factor. A second-order tensor approximation of the relative magnetic permeability of the composite is proposed to determine the in-plane fibre orientation factor along any direction based on any three non-collinear measurements. Experimental evidence is presented supporting the theoretical developments. The factors that may affect the measurements are experimentally quantified. The paper concludes with an application example.

Study on the electrical-thermal properties of lithium-ion battery materials in the NCM622/graphite system.

The phenomenon of fire or even explosion caused by thermal runaway of lithium-ion power batteries poses a serious threat to the safety of electric vehicles. An in-depth study of the core-material thermal runaway reaction mechanism and reaction chain is a prerequisite for proposing a mechanism to prevent battery thermal runaway and enhance battery safety. In this study, based on a 24 Ah commercial Li(Ni0.6Co0.2Mn0.2)O2/graphite soft pack battery, the heat production characteristics of different state of charge (SOC) cathode and anode materials, the separator, the electrolyte, and their combinations of the battery were investigated using differential scanning calorimetry. The results show that the reaction between the negative electrode and the electrolyte is the main mode of heat accumulation in the early stage of thermal runaway, and when the heat accumulation causes the temperature to reach a certain critical value, the violent reaction between the positive electrode and the electrolyte is triggered. The extent and timing of the heat production behaviour of the battery host material is closely related to the SOC, and with limited electrolyte content, there is a competitive relationship between the positive and negative electrodes and the electrolyte reaction, leading to different SOC batteries exhibiting different heat production characteristics. In addition, the above findings are correlated with the battery failure mechanisms through heating experiments of the battery monomer. The study of the electro-thermal properties of the main materials in this paper provides a strategy for achieving early warning and suppression of thermal runaway in batteries.

Influence of an Engineered Notch on the Electromagnetic Radiation Performance of NiTi Shape Memory Alloy.

This work explores the influence of a pre-engineered notch on the electromagnetic radiation (EMR) parameters in NiTi shape memory alloy (SMA) during tensile tests. The test data showed that the EMR signal fluctuated between oscillatory and exponential, signifying that the specimen's viscosity damping coefficient changes during strain hardening. The EMR parameters, maximum EMR amplitude, and average EMR energy release rate remained constant initially but rose sharply with the plastic zone radius with progressive loading. It was postulated that new Frank-Read sources permit dislocation multiplication and increase the number of edge dislocations participating in EMR emissions, leading to a rise in the value of EMR parameters. The study of the correlation between EMR emission parameters and the plastic zone radius before the crack tip is a vital crack growth monitoring tool. An analysis of the interrelationship of the EMR energy release rate at fracture with the elastic strain energy release rate would help develop an innovative approach to assess fracture toughness, a critical parameter for the design and safety of metals. The microstructural analysis of tensile fractures and the interrelation between deformation behaviours concerning the EMR parameters offers a novel and real-time approach to improve the extant understanding of the behaviour of metallic materials.

Investigations on the development of impact-resistant thermoplastic fibre hybrid composites from glass and steel fibre

With the increased use of fibre reinforced composites (FRP), the design of new generation of composite structures with high stiffness and a ductile material behaviour is required to cope with complex load scenarios and high damage tolerances. This can be achieved, in particular, by a combination of conventional fibre-reinforced composites (FRP), which possess high stiffness and strength with metallic materials characterized by their high ductility and associated higher energy absorption capacity. Currently, there are no solutions for hybridisation of high performance filament yarns, metal filament yarns and thermoplastic filament yarns on micro level. Therefore, the main objective of this study is to develop a fibre hybrid composite based on hybrid yarn consisting of glass, steel and polypropylene filament yarns and to compare its tensile and impact properties with those of the composite reinforced only with glass filament yarn. The tensile and impact properties of the unidirectional hybrid composites produced from the developed multi-material hybrid yarn consisting of steel, glass and polypropylene filament yarns are compared with those of a non-hybrid composite reinforced exclusively with glass filament yarn. The results show that by hybridising with steel fibres a characteristic post-failure behaviour can be achieved, so that the developed multi-material hybrid yarns have a high potential for use in composites with high crash and impact performance requirements, where safety demands are essential.

Two scale models for fracture behaviours of cementitious materials subjected to static and cyclic loadings

This study employs a lattice fracture model to simulate static and fatigue fracture behaviour of Interfacial Transition Zone (ITZ) at microscale and mortar at mesoscale. The heterogeneous microstructure of ITZ and mesostructure of mortar are explicitly considered in the models. The initial step involves calibrating and validating the microscopic model of the ITZ through micro-cantilever bending tests. Subsequently, this validated ITZ model serves as a constitutive law to simulate the fracture behavior of mortar at the mesoscale using an uncoupled upscaling method. The influence of microstructural features, such as w/c ratio and microscopic roughness, on the fracture behaviour of ITZ is investigated. Moreover, the effect of ITZ properties and stress level on the fracture performance and fatigue damage evolution of mortar is also studied. The simulation results for both the ITZ and mortar demonstrate good agreement with experimental results. The proposed two models provide insights into the fracture mechanisms and fatigue damage evolution in cementitious materials subjected to static and cyclic loadings.

Fermenting Knits: A material-driven exploration of knit-based bacterial cellulose biocomposite textile materials through fibre reassembly

ABSTRACT Environmental concerns surrounding textile production have increased the need and interest in developing material innovations and interdisciplinary approaches to offset this ecological impact. Bacterial cellulose is present in several industries, and its biologically produced form has shown potential use within fashion. Within the emerging field of biodesign, research surrounding bacterial cellulose textiles generally focuses on the initial sheeted growth, while alternative outputs and working methods remain scarce. Here, fibre reassembly is analysed by fully integrating broken down BC fibres with knitted structures. Material selection and working methods take a practice-led approach to experiment formulation in order to observe material behaviour as central to development. This project aims to create biocomposite textiles that enhance the properties of bacterial cellulose and expand its designable characteristics through low-tech working methods accessible from designerly backgrounds. The results are intended to inform further research in footwear design contexts, as basis to develop BC-based components. Experimentation shows BC fibres reassembled around the knitted structures, varying according to yarn choice and fermenting environment alteration. This demonstrates potential for material and methodology development while exploring co-design with living organisms. In the context of future applications, BC-based composite textiles can self-assemble at different growth stages, offering the possibility of material-driven approaches to spaces intersecting biology and design.

CORROSION BEHAVIOUR OF ADDITIVELY MANUFACTURED METALLIC MATERIALS

Additive manufacturing (AM) represents a technological advancement over traditional manufacturing methods, offering cost-effective production of high-quality, geometrically complex components for various applications. With its ability to rapidly manufacture metallic parts and a capability to better customise products due to the possible recycling of used powder materials, AM facilitates customized product development. On the other hand, the technology raises questions regarding microstructure, residual stresses, porosity and surface roughness. All these aspects need to be evaluated to achieve the quality of the end products. This paper reviews the corrosion behaviour of AM-produced metallic materials, examining how various factors, including porosity, microstructure, melt-pool boundaries, residual stresses, and surface roughness, influence the end-product quality.

On the fatigue behaviour of epoxy-based nanostructured composite materials

Epoxy composites and nanocomposites enable the creation of high-performance structures and innovative designs. However, there is limited research focused on their fatigue characterization. The purpose of this study is to analyze the fatigue resistance results of nanostructured composite materials made with an epoxy matrix of Diglycidyl Ether of Bisphenol F and 9,9-bis(3-chloro-4-aminophenyl) fluorine (DGEBF-CAF) reinforced with 5%wt of elastomeric nanoparticles with an average diameter of 200 nm. The tests are conducted at variable load and frequency using Rotating Bending (R-B) and Tensile-Tensile (T-T) tests, and the results are compared to those obtained with pure resin. The occurrence of thermal fatigue phenomena during the tests is monitored using a thermal camera. The results confirm that pure epoxy resin exhibits poor crack propagation resistance due to its low ductility and toughness, and the introduction of a second phase leads to an improvement of approximately 3 times in T-T tests and 5 times in R-B tests.

Impact Strain Signal Characteristics of Al and Mg under Instrumented Charpy Test

Impact strain signal is used to examine strain signal patterns under various parameters. Impact is a complicated phenomenon that occurs within a millisecond timeframe. Material toughness is measured by the energy absorption recorded by the Charpy machine and closely related to the specimen fracture deformation. By utilizing the strain gauge and data acquisition, the impact strain signal provides additional data regarding impact duration, maximum strain value and the area under curve for a deeper understanding of the impact problem. A material with high toughness has great energy absorption and the capability to withstand high impact load. Although magnesium is lighter in weight compared to aluminium, aluminium is a better corrosion-resistant material and is stronger, which makes it more suitable to be fabricated as automotive structural components. Tensile test is typically used for investigating a material’s mechanical properties. In the automotive industry, materials are required to have good crashworthiness. This study investigates the relationship between the energy absorbed with the power spectral density and the area under strain–time graph for different materials, impact speeds, and material thicknesses. Furthermore, the relationship between the stress–strain curve and impact strain signal were examined. In this study, the behaviour of two materials, namely Aluminium 6061-T6 and Magnesium AM60, was investigated using instrumented Charpy test, by referring to the impact strain signal pattern result. For the experiment, strain gauge attached to the Charpy machine striker was employed and linked to the data acquisition system. Charpy impact specimen has three different thicknesses; 10 mm, 7.5 mm and 5 mm. Impact speed is at 3.35 m/s and 5.18 m/s. Results show a correlation between energy absorbed with strain energy. Strain energy obtained is directly proportional to the energy absorbed. Aluminium 6061-T6 has the highest energy absorption, maximum strain, and strain energy under power spectral density graph compared to Magnesium AM60. Relation of strain signal from Charpy test and stress–strain curve from tensile test shows a significant finding where the material deforms and fracture points are identified through the signal pattern and curve. Thus, the strain signal pattern can be used to predict material behaviour.

Granular behaviour under bi-directional shear with constant vertical stress and constant volume

This paper aims to investigate the role of bi-directional shear in the mechanical behaviour of granular materials and macro-micro relations by conducting experiments and discrete element method (DEM) modelling. The bi-directional shear consists of a static shear consolidation and subsequent shear under constant vertical stress and constant volume conditions. A side wall node loading method is used to exert bi-directional shear of various angles. The results show that bi-directional shear can significantly influence the mechanical behaviour of granular materials. However, the relationship between bi-directional shear and mechanical responses relies on loading conditions, i.e. constant vertical stress or constant volume conditions. The stress states induced by static shear consolidation are affected by loading angles, which are enlarged by subsequent shear, consistent with the relationship between bi-directional shear and principal stresses. It provides evidence for the dissipation of stresses accompanying static liquefaction of granular materials. The presence of bi-directional principal stress rotation (PSR) is demonstrated, which evidences why the bi-directional shear of loading angles with components in two directions results in faster dissipations of stresses with static liquefaction. Contant volume shearing leads to cross-anisotropic stress and fabric at micro-contacts, but constant vertical stress shearing leads to complete anisotropic stress and fabric at micro-contacts. It explains the differentiating relationship between stress-strain responses and fabric anisotropy under these two conditions. Micromechanical signatures such as the slip state of micro-contacts and coordination number are also examined, providing further insights into understanding granular behaviour under bi-directional shear.