Bang-bang Phase-frequency Detector Research Articles

A 1.6-GHz DPLL Using Feedforward Phase-Error Cancellation

A digital phase-locked loop (DPLL) using the feedforward phase-error cancellation (FPC) is presented. The phase error of this DPLL using a digitally controlled ring oscillator is quickly canceled by a digitally controlled delay line (DCDL), which improves the phase noise performance. The loop gain of this FPC DPLL is also calibrated. In addition, a dead-zone-free (DZF) bang-bang phase-frequency detector (BBPFD) is presented to enhance the resolution of the time-to-digital converter (TDC). This proposed DPLL is fabricated in a 40-nm CMOS process which occupies 0.05 mm2. The measured rms jitter integrated from 1 kHz to 100 MHz is 788 fs at 1.6 GHz. The measured reference spur is −57.84 dBc for a 50 MHz reference frequency. Its power consumption is 5 mW for a 1.1-V supply voltage.

A fast locking and low jitter hybrid ADPLL architecture with bang bang PFD and PVT calibrated flash TDC

In the present work, an all digital phase locked loop architecture (ADPLL) employing a bang-bang phase frequency detector (BB-PFD) and the 3-bit flash based time to digital converter (TDC) is designed to enhance the jitter and locking time performance. The proposed ADPLL utilizes a low power and high resolution 3-bit flash TDC with foreground calibration to suppress the issues of process, voltage and temperature (PVT) spreads and achieves low jitter and low power ADPLL. To obtain the fast locking, a proposed dynamic bang-bang PFD is used. The proposed ADPLL takes only 5 iterations to achieve the locking from unlocked state. Additionally, ADPLL employs a wide range and low phase noise voltage controlled oscillator (VCO) based on inverters to obtain a reduced jitter in ADPLL. The proposed ADPLL is designed in 180-nm SCL digital CMOS technology at 1.8 V supply. It consumes a total power of 5.94 mW at 1.8 V. From the post layout simulations, the achieved FoM and periodic jitter is −227.6 dB and 1.71 ps respectively at an output frequency of 1.6 GHz. The achieved phase noise of proposed ADPLL is −131.2 dBc/Hz at offset of 100 MHz.

A fast-locking bang-bang phase-locked loop with adaptive loop gain controller * * Project supported by the National Nature Science Foundation of China (Nos. 61331003, 61474108), the National Key Technology Research and Development Program of the Ministry of Science and Technology of China (No. 2016ZX03001002).

This paper proposes a fast-locking bang-bang phase-locked loop (BBPLL). A novel adaptive loop gain controller (ALGC) is proposed to increase the locking speed of the BBPLL. A novel bang-bang phase/frequency detector (BBPFD) with adaptive-mode-selective circuits is proposed to select the locking mode of the BBPLL during the locking process. Based on the detected results of the BBPFD, the ALGC can dynamically adjust the overall gain of the loop for fast-locking procedure. Compared with the conventional BBPFD, only a few gates are added in the proposed BBPFD. Therefore, the proposed BBPFD with adaptive-mode-selective circuits is realized with little area and power penalties. The fast-locking BBPLL is implemented in a 65 nm CMOS technology. The core area of the BBPLL is 0.022 mm2. Measured results show that the BBPLL operates at a frequency range from 0.6 to 2.4 GHz. When operating at 1.8 GHz, the power consumption is 3.1 mW with a 0.9-V supply voltage. With the proposed techniques, the BBPLL achieves a normalized locked time of 1.1 μs @ 100 MHz frequency jump. The figure-of-merit of the fast-locking BBPLL is −334 dB.

A 6.7–11.2 Gb/s, 2.25 pJ/bit, Single-Loop Referenceless CDR With Multi-Phase, Oversampling PFD in 65-nm CMOS

A single-loop referenceless clock and data recovery (CDR) with a compact frequency acquisition scheme is presented. A bang–bang phase–frequency detector (BBPFD) is proposed that tracks the frequency difference by detecting the drift direction of the non-return to zero bit stream with respect to the multi-phase clock and generates UP/DN output signals accordingly. When frequency locked, the BBPFD is degenerated into the conventional bang–bang phase detector (BBPD). The UP/DN output signals from the BBPFD are thus connected directly to the loop filter, thereby reducing the acquisition time without any loss of cycles. The effect of sampling phase mismatch is analyzed, and the capture range is calculated. In addition, the frequency acquisition time is analytically derived and verified by simulation. The proposed CDR has been implemented in a 65-nm CMOS process and occupies an active area of 0.047 mm2. The measured capture range is 6.7–11.2 Gb/s, and the frequency acquisition time is less than 2.19 $\mu \text{s}$ . The proposed CDR achieves error-free operation (BER < 10−12) for PRBS31 pattern and consumes 22.5 mW at 10 Gb/s.

An Optimum Loop Gain Tracking All-Digital PLL Using Autocorrelation of Bang–Bang Phase-Frequency Detection

An all-digital phase-locked loop with a bang-bang phase-frequency detector (BBPFD) that tracks the optimum loop gain for minimum jitter is proposed. The autocorrelation of the output of BBPFD indicates whether the bang-bang PLL operates in the nonlinear regime or the random noise regime. An adaptive loop gain controller continuously evaluates the autocorrelation of the BBPFD output and adjusts the loop gain to make the autocorrelation zero. The digital loop filter operates at higher than the reference clock frequency to reduce the loop latency and to mitigate the resolution of the digitally controlled oscillator. The prototype chip has been fabricated in a 65-nm CMOS process. The core consumes 5 mW at 2.5 GHz and exhibits root-mean-square jitter of 1.72 ps.

A 0.3–1.4 GHz All-Digital Fractional-N PLL With Adaptive Loop Gain Controller

A 0.3–1.4 GHz all-digital phase locked loop (ADPLL) with an adaptive loop gain controller (ALGC), a 1/8-resolution fractional divider and a frequency search block is presented. The ALGC reduces the nonlinearity of the bang-bang phase-frequency detector (BBPFD), reducing output jitter. The fractional divider partially compensates for the large input phase error caused by fractional-N frequency synthesis. A fast frequency search unit using the false position method achieves frequency lock in 6 iterations that correspond to 192 reference clock cycles. A prototype ADPLL using a BBPFD with a dead-zone-free retimer, an ALGC, a fractional divider, and a digital logic implementation of a frequency search algorithm was fabricated in a 0.13- <formula formulatype="inline" xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"><tex Notation="TeX">$\mu{\hbox {m}}$</tex></formula> CMOS logic process. The core occupies 0.2 <formula formulatype="inline" xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"><tex Notation="TeX">${\hbox {mm}}^{2}$</tex> </formula> and consumes 16.5 mW with a 1.2-V supply at 1.35-GHz. Measured RMS and peak-to-peak jitter with activating the ALGC are 3.7 ps and 32 ps respectively.