Austenite Reversion Research Articles

Effect of Austenite Reversion Treatment and Partitioning on the Phase Transformation Behavior and Mechanical Properties of Martensitic–Austenitic CrMnNi‐Cast Steel

Effect of Austenite Reversion Treatment and Partitioning on the Phase Transformation Behavior and Mechanical Properties of Martensitic–Austenitic CrMnNi‐Cast Steel

Solute and phase heterogeneous distribution at different scales and its effect on ageing physical phenomena in a laser powder bed fusion produced maraging steel

The Laser Powder Bed Fusion process involves complex thermodynamic and heat transfer mechanisms which results in a complicated understanding of the material’s microstructure and phase transformation processes. In the case of additive manufacturing maraging steels, these present heterogeneous structures which mainly consist of Body-Centred Tetragonal (BCT) martensite and retained austenite (Face-Centred Cubic (FCC) phase structure), unlike conventionally processed material. Research has already been done on the competitive or collaborative nature of austenite growth/reversion and precipitation in these materials. However, for Laser Powder Bed Fusion maraging steels, studies have focused on either the effect of the heterogeneous structures on austenite reversion kinetics or the formation, evolution and behaviour of precipitation. Still, no comprehensive research exists that covers in detail the relation between solute heterogeneity from the meso- to the nanoscale and its influence on both phase distribution and ageing physical phenomena. To do so, multiscale chemical analyses and microstructural characterisation techniques were used to investigate a maraging steel M300 in different transformed conditions: as-built, aged at 480 and 540 °C. The results showed that competing mechanisms during printing caused segregation at the mesoscale, which remains in aged samples. Vaporisation led to Cr segregation, while melt convections caused Ni and Ti depletion at melt pool boundaries. Retained austenite location was found at melt pool boundaries and away from them on the as-built structure. Its preferential location remains unclear. Dissimilarities from conventional material were identified in nanosized clustering and precipitates on aged samples.

New strategy to simultaneously improve strength-toughness balance for low-carbon ultrastrong steel by multi-step heat treatment process

The quenching-partitioning-tempering (QPT) multi-step heat treatment process was employed to enhance the strength-toughness balance of low-carbon ultrastrong steel based on the controllable transformation-induced plasticity (TRIP) effect and co-precipitation strengthening. The aging embrittlement of ultrastrong steel, with an impact toughness of only 5.8 J at peak strength, has been effectively addressed through the QPT process. The sufficient reversed austenite (RA) can be obtained by controlling the partition temperature to 650 °C, followed by aging at 550 °C to fully re-precipitate nanoparticles. The volume fraction of RA in QPT650 steel reached 16.4 %, and the number density of nanoparticles increased dramatically, resulting in a high yield strength of 1233 MPa and excellent impact toughness of 60.4 J. The coarsening and re-precipitation of nanoparticles were clarified, and the strengthening increments of QPT650 steel reaches 584.6 MPa, and the substantial enhancement of Orowan strengthening is responsible for the high yield strength. The excellent impact toughness of QPT650 steel is attributed to the obvious TRIP effect of RA that consumes a large amount of crack propagation energy, and a small number of sheared nanoparticles provide limited micro-cracks, resulting in a strong crack resistance.

Effect of heat treatment processes on the microstructure and mechanical properties of 00Cr13Ni5Mo super martensitic stainless steel (SMSS)

The effects of quenching and tempering temperatures on the microstructure and mechanical properties of super martensitic stainless steel (SMSS) 00Cr13Ni5Mo were studied. The SMSS after heat treatment is composed of martensite (α phase) and a small amount of austenite. When the quenching temperature is 930 °C, with the increase of tempering temperature, the enrichment of Ni in martensite leads to the formation of reverse austenite, the content of martensite phase decreases from 84.9 % to 80.0 %, and the average grain size increases from 23.23 μm to 27.07 μm. When tempering at 580 °C, the content of martensite phase decreases from 80.0 % to 83.7 % with the increase of quenching temperature. The average grain size increased from 25.23 μm to 35.01 μm. When the quenching temperature is 930 °C, the hardness and yield strength of SMSS decrease, and the hardness and yield strength are the highest at 530 °C, which are 275 HV and 873 MPa. The plasticity increases first and then decreases, and the plasticity is the best at 580 °C. The elongation and reduction of area were 22.87% and 71.41%. These changes in mechanical properties are mainly related to the content of martensite and reversed austenite in the microstructure. The tensile strength and elongation of SMSS under different process conditions were compared. The results show that when the quenching temperature is 930 °C and the tempering temperature is 580 °C, the comprehensive performance of SMSS is the best, reaching 18700 MPa•%. This value is 31% higher than that of forgings. Finally, the formation mechanism of reversed austenite was discussed, and the strengthening model of SMSS 00Cr13Ni5Mo was established.

Heat treatment effects and variant selection in multi-material laser powder bed fusion of FeNi- and CoCr-based alloys

ABSTRACT This study demonstrates the successful fabrication of a multi-material 18Ni(300) maraging steel – CoCrMo alloy using laser powder bed fusion (L-PBF), which in its as-built state, displays suboptimal mechanical performance. Addressing this, we propose different heat treatments that mutually enhance the properties of both alloys. Comparative analysis of texture development, precipitation sequence and mechanical properties of the dual structures at different scales has been conducted. The results indicate the cooperative strengthening of intragranular γ–ϵ transformation in CoCrMo, and Ni3Ti precipitation in maraging steel. Adding the solution treatment also balanced the formation of acicular Ni3Ti clusters with (Fe, Ni, Co)2(Ti, Mo) precipitates, and revealed that chemical segregation influences austenite reversion. Initial evidence of local grain variant selection has been revealed in as-built samples due to thermal cycling and austenite reversion, which generates residual stresses, recoil forces and convective flow. Surprisingly, the missing variants can also be inherited after heat treatment with insufficient solution temperatures.

In-situ alloying of maraging steel with enhanced mechanical properties and corrosion resistance by laser directed energy deposition

Maraging steels are known for their exceptional strength derived from the martensite matrix and nano-precipitate strengthening. However, the trade-off to the high strength is often a loss of ductility and minimal strain hardening. Introducing metastable austenite to the matrix to activate transformation-induced plasticity (TRIP) is an effective approach to achieve high strength and ductility synergy. Existing methods to introduce TRIP into additively manufactured maraging steels are limited by the compositions of pre-alloyed powder or additional heat treatment steps. In-situ alloying via the laser directed energy deposition (L-DED) process allows flexibility in tailoring the alloying composition to achieve an austenite–martensite microstructure. Herein, we develop a TRIP–maraging steel by in-situ alloying of M789 with 316L (4–8 wt%) during the L-DED process. The addition of 316L facilitates austenite reversion in solution-treated maraging steel. As a result, the TRIP–maraging steel exhibits a 76 % increase in uniform elongation at the expense of a minimal sacrifice of strength. Furthermore, the corrosion resistance of the TRIP–maraging steel is enhanced. This work showcases a pathway to developing superior alloys by in-situ alloying via additive manufacturing.

Effect of prior austenite grain size on austenite reversion, bainite transformation and mechanical properties of Fe-2Mn-0.2C steel

To elucidate the response of austenite reversion and subsequent bainite transformation behavior to the prior austenite grain (PAG) size, the transformation kinetics and amount of reverted austenite in the intercritical region, the subsequent bainite transformation kinetics, and the tensile properties were investigated by dilatometers, scanning electron microscopy, electron backscatter diffraction, transmission electron microscopy, and the mechanical tests. The results show that, when annealed at 730 °C, fine-grained specimens exhibit faster reverted austenite transformation rate than coarse-grained specimens due to the presence of more PAG boundaries. As the intercritical temperature rises to 760 °C, more intragranular globular austenite forms in the coarse-grained specimen, which accelerates the reverted austenite transformation rate. Compared to fine-grained specimens, coarse-grained specimens exhibit faster bainite transformation and higher amount of bainitic ferrite. The microstructure after austempering consists of intercritical ferrite, bainitic ferrite, RA and fresh martensite. With increasing the austempering time, more bainitic ferrite is formed and the amount of RA and fresh martensite decreases. With increasing the austempering time, the increase in the amount of bainitic ferrite leads to an increase in the yield strength, while the decrease in the amount of RA leads to a decrease in the elongation. Moreover, compared with coarse-grained specimens, the finer microstructure in fine-grained specimens improves yield and tensile strengths, while higher amount of RA contributes to larger uniform and total elongations.

Laser Powder Bed Fusion and Heat Treatment of the Martensitic Age‐Hardenable Steel (1.2709)

The primary objective of this study is to clarify the fundamental question of whether, in principle, it is possible to dispense with a prior solution annealing process in favor of a direct aging heat treatment for specimens of maraging stainless steel grade X3NiCoMoTi18‐9‐5 (1.2709) produced by laser powder bed fusion (LPBF). The waiver of a solution annealing process would significantly increase the process efficiency and thus support a sustainable and resource‐friendly production of such components. Therefore, the hardness, microstructure, and the present phases of specimens in as‐built + aged condition (AB + A) and solution‐annealed + aged (SOL + A) are examined during this study. Initially, an extended parameter study is performed using a Renishaw AM 250 LPBF system equipped with a pulsed mode laser system to achieve the highest possible apparent density. As test specimens, small cubes are produced for parameter study and are analyzed for porosity by means of optical microscopy. To investigate the relationship between microstructure and hardness in different material states, one series of specimens is aged directly after LPBF processing in the as‐built state (AB + A). For comparison, the other series was solution annealed at 820 °C for 60 min, quenched in water and then aged (SOL + A). A maximum hardness value of 614 HV1.0 is achieved for specimen aged at 490 °C for 120 min in as built condition (AB + A), while 624 HV1.0 was measured for specimen aged at 490 °C for 180 min in conventionally solution annealed + aged (SOL + A) condition. Significant austenite reversion is not observed at aging temperature of 490 °C in both cases. Aging of specimens at temperatures of 540 and 600 °C resulted in reduction of specimen hardness due to higher percentage of austenite reversion. No significant difference between the hardness values of AB + A and SOL + A specimens is observed. It can therefore be concluded that, in principle, conventional solution annealing and ageing can be dispensed with in favor of direct aging. However, as the results are based on small sized specimens, further investigations into the scalability are needed.

Superior combination of strength and ductility in Fe–10Mn-0.6C steel trigged by austenite reversion transformation

Austenite reversion transformation process was employed on Fe–10Mn-0.6C steel to adjust the content and stability of austenite and the transformation-induced plasticity effect was effectively improved. With increasing annealing temperatures from 550 °C to 590 °C and 620 °C, the content and proportion of lath-like austenite significantly increased. Austenite exhibited different stability after annealing at different temperatures, mainly related to the distribution of Mn and C. The higher the local Mn and C concentration, the more stable austenite, vice versa. After annealing at 620 °C for 6 h, the highest austenite content of 61 % was achieved, and half of that had a lath-like morphology. The steel had a superior combination of ultimate tensile strength of 1500 MPa and elongation of 59 %, resulting from the enhanced transformation-induced plasticity effect. The key reason was the alternating distributions of austenite and ferrite laths, accompanied with the formation of nanotwins in the austenite with high stability.

Anomalous magnetization induced by local chemistry fluctuations in Mn-containing α’-martensite

An anomalous increase in magnetization was investigated in a cold-rolled high-Mn TRIP steel (16.8 wt% Mn) annealed at 350°C for times varying from 5 to 120 min, before the start of austenite reversion (α’ → γ). Besides in-situ and ex-situ magnetic measurements, the full characterization of this phenomenon was also performed with the aid of X-ray diffraction (XRD), Mössbauer spectroscopy, and microstructural characterization using electron backscatter diffraction (EBSD) and atom probe tomography (APT). Based on XRD measurements, the volume fraction of austenite and α’-martensite was estimated as a function of annealing time, as well as their lattice strain. Phase quantification confirmed the absence of newly-fresh α’-martensite in the material during annealing at 350°C. Short annealing up to 15 min promoted the increase of Ms (saturation magnetization) due to stress relief in α’-martensite (Villari effect). Further annealing to 30 min promotes the decrease in Ms driven by short-range solute reorganization within the lattice. After 60 min annealing, the creation of long-range solute-depleted zones (i.e. confined zones highly enriched in Fe) causes a new increase in Ms. In comparison, for 120 min of annealing time, Ms tends to remain unaltered. These findings revealed that short- and long-range chemical fluctuations strongly affect the saturation magnetization of the steel and brought new insights on the use of magnetic probing as a tool for phase quantification in Mn-bearing steels.

Effect of ageing temperature on the microstructural evolution and mechanical properties in M2C and NiAl co-precipitation secondary hardening ultrahigh-strength steel

A novel cost-effective secondary hardening ultrahigh-strength steel, strengthened by the co-precipitation of M2C and NiAl, was developed. The present study systematically investigated the co-precipitation evolution, austenite reversion, and mechanisms of strengthening and toughening at different ageing temperatures. As the ageing temperature increased, the quenched microstructure underwent various transformations, including precipitation and dissolution of cementite, nucleation and coarsening of M2C and NiAl nanoparticles, as well as reversion of austenite. At ageing temperatures of 427 °C and 454 °C, a small amount of cementite was present in the martensite matrix, and M2C and NiAl precipitates started to form, resulting in low strength and poor toughness. At 482 °C, the peak-ageing stage was reached, achieving a maximum yield strength of 1875 ± 4 MPa and an ultimate tensile strength of 2185 ± 3 MPa. This strength is primarily attributed to shear strengthening of NiAl particles and Orowan strengthening of M2C carbides. Additionally, the complete dissolution of cementite at this stage improved toughness. As the ageing temperature increased to 510 °C and 538 °C, the strength decreased due to coarsening of M2C, while the toughness improved as a result of film austenite reversion and enhanced dislocations bypassing around the M2C carbides.

Effect of Heat Input on Austenite Reversion, Recrystallization, and Ensuing Impact Toughness in Simulated Intercritical Coarse‐Grained Heat Affected Zone of Medium Mn Steel

A systematic experimental study has been conducted on the simulated intercritical coarse‐grained heat affected zone of 690 MPa grade heavy‐plate medium Mn steel by tailoring heat input of the first welding pass to obtain the influence of initial microstructure on the austenite reversion mechanism, recrystallization, and resultant impact toughness. Results reveal that prior austenite grain size significantly increases from 30 ± 11, 41 ± 14 to 54 ± 15 μm with the increasing heat input from 15, 30 to 50 kJ cm−1, which affect the nucleation site of reversed austenite, recrystallization mechanism, and final microstructure. Accordingly, impact toughness is better at the heat input of 30 kJ cm−1 (75.2 ± 0.8 J) in comparison with that of 15 kJ cm−1 (63.3 ± 13.3 J) and 50 kJ cm−1 (26.7 ± 6.5 J) at −40 °C, which is mainly ascribed to the formation of lamellar heterogeneous structures, multiplication of slip system and morphology of high‐angle grain boundaries.

Precipitation and reverted austenite formation in maraging 350 steel: Competition or cooperation?

Aged maraging steels offer unique strength and toughness via the presence of finely dispersed precipitates, allowing the material to reach values of up to 2400 MPa in yield strength in the case of 18Ni350. However, when aging heat treatments above 550 °C are conducted, simultaneous precipitation and austenite reversion can occur changing the mechanical behavior of the material. Although many studies related to the physical metallurgy of maraging steels have already been published, less attention has been given to a detailed understanding of the initial formation of austenite and its relationship with the precipitates. In this study, undeformed and cold rolled commercial 18Ni350 maraging steel samples were submitted to short aging heat treatments of 1800s at 600, 650, and 700 °C. The influence of the initial microstructure on subsequent phase evolution was studied using in-situ synchrotron X-ray diffraction and final microstructural products using transmission electron microscopy and atom probe tomography. Results show that cold rolled samples did not present faster kinetics of transformation of reverted austenite as expected, but this condition presented austenite in a different morphology than the undeformed condition. However, cold rolling changed the morphology of reverted austenite from elongated (undeformed case) to equiaxed; and induced a higher density of smaller Ni3Ti and Fe2Mo precipitates, especially after low-temperature aging. Besides, the deformation extinguished retained austenite, which influenced the reverted austenite formation, concluding that the simple increase in dislocation density is not a unique and direct factor to increase the reverted austenite kinetics.

Effect of Manganese on the Strength-Toughness Relationship of Low-Carbon Copper and Nickel-Containing Hull Steel.

The influence of varying the manganese (Mn) contents of high-strength copper-containing hull steel on its microstructural evolution and mechanical properties was investigated. With increasing Mn content from 2 to 5%, the tensile strength of the steel increased by ~100 MPa, while the elongation of steel remained at ~23.5%, indicating good plasticity. However, the 2Mn sample had 128 J higher low-temperature (-84 °C) impact work than the 5Mn sample. The microstructures of different Mn steels were composed of fresh martensite (FM), ferrite/tempered martensite (F/TM), and reversed austenite (RA). The increase in Mn content markedly increased the presence of RA and intensified the work hardening caused by the transformation-induced plasticity (TRIP) effect during the tensile process. However, as the phase transformation in different Mn steels occurred in the early stage of strain and did not extend throughout the entire plastic deformation process, increasing plasticity via phase transformation was difficult. In addition, although the volume fraction of RA increased significantly in 4Mn and 5Mn steels, the stability of RA significantly decreased. The presence of numerous metastable blocks and coarse lath-like RA contributed little to low-temperature impact work and was even detrimental to toughness. The substantial fresh martensite resulting from phase transformation facilitated microcrack generation, owing to rapid volume expansion and mutual impacts, thus reducing the work required for crack formation. Additionally, the abundance of deformation twins significantly reduced the work needed for crack propagation. These combined actions significantly reduced the low-temperature toughness of 4Mn and 5Mn steels.

Optimizing the Strength and Toughness of V/Mo-Modified 0.22C-5.24Mn Steel by Short-Time Partial Austenitization Process.

In order to obtain the good match between yield strength and low-temperature toughness, the short-time partial austenitization (SPA) process was employed for V/Mo-bearing 0.22C-5.24Mn steel. The initial microstructure after intercritical tempering was dual-phase ferrite and reversed austenite (RA), while the final microstructure consisted of ferrite, RA, and secondary martensite (SM) after being subjected to the SPA process. (V, Mo)C with disclike morphology mainly precipitated during intercritical tempering, and the aspect ratio of particles decreased, leading to the appearance of near-spherical morphology. After being subjected to SPA process, the resultant multiphase hierarchical microstructure (three layers: outer layer of ferrite, interlayer of SM, and inner layer of RA) enabled a high yield strength of 1097 MPa, a total elongation of 14%, and an impressive impact energy of 33.3 J at -20 °C. The strengthening contribution of (V, Mo)C precipitation was estimated to be about 108 MPa.

Modelling the Overaging Kinetics of 18Ni250 Maraging Steel

Abstract The kinetics of overaging in 18Ni250 maraging steel was studied by (i) modelling the overaging softening behavior, (ii) an aging parameter approach, and (iii) modelling the kinetics of austenite reversion. Changes in kinetics of 18Ni250 maraging steel is calculated as a function of volume fraction of reverted austenite. Softening behavior during overaging was modelled by the Wilson model and the Pardal et al. model. Both the models were found to be in good agreement with experimental data, but the Pardal et al. model showed a better fit. An S-type curve had a better fit compared to a linear fit while relating hardness to the aging parameter with a material constant of C = 20. The kinetics of austenite reversion was studied using the JMAK model, and the activation energy for the austenite reversion process was estimated as 218 kJ/mol.

Austenite Reversion Behavior of Maraging Steel Additive-manufactured by Laser Powder Bed Fusion

This study was set to fundamentally investigate the characteristics of austenite reversion occurring in maraging steels additive-manufactured by laser powder bed fusion (L-PBF). The maraging steel samples manufactured under different L-PBF process conditions (laser power P and scan speed v) were subjected to heat treatments at 550 oC for various durations, compared with the results of the austenitized and water-quenched sample with fully martensite structure. The L-PBF manufactured samples exhibited the martensite structure (including localized austenite (γ) phases) containing submicron-sized cellular structures. Enriched alloy elements were detected along the cell boundaries, whereas such cellar structure was not found in the water-quenched sample. The localized alloy elements can be rationalized by the continuous variations in the γ-phase composition in solidification during the L-PBF process. The precipitation of nanoscale intermetallic phases and the following austenitic reversion occurred in all of the experimental samples. The L-PBF manufactured samples exhibited faster kinetics of the precipitation and austenite reversion than the water-quenched sample at elevated temperatures. The kinetics changed depending on the L-PBF process condition. The enriched Ni element (for stabilizing γ phase) localized at cell boundaries would play a role in the nucleation site for the formation of γ phase at 550 oC, resulting in enhanced austenite reversion in the L-PBF manufactured samples. The variation in the reaction kinetics depending on the L-PBF condition would be due to the varied thermal profiles of the manufactured samples by consecutive scanning laser irradiation operated under different P and v values.

Friction Stir Welding‐Induced Microstructural Changes in Low‐Alloy Steel Post‐Tempforming

A feasibility of friction stir welding for a high‐strength low‐alloy steel subjected to tempforming, that is, tempering followed by large‐strain warm rolling at tempering temperature, is presented. The martensite microstructure tempered at 873 K for 1 h and then subjected to warm rolling to total strain of 1.5 is characterized by a lamellar‐type ultrafine‐grained microstructure consisting of pan‐caked grains with the transverse size of 560 nm and exhibits the tensile strength of 1020 MPa. The friction stir welding is accompanied by heating the stir zone of the welded sample well above Ac1 temperature. Hence, the welding seam experiences austenite reversion followed by martensitic transformation. The microstructure evolved in the stir zone is composed of near‐equiaxed grains with an average size of 1.3 μm. Nevertheless, the stir zone possesses increased hardness up to 350 HV as compared to that of 290 HV in the base material after tempforming. Upon tensile test of the welded joint, the strain localization followed by fracture occurs in the heat‐affected zone close to the stir zone. The tensile strength of 970 MPa is obtained for the welded joint that is quite close to the base material after temforming.

Improvement of shape recovery by controlling the microstructure and mechanical properties in a thermomechanically-treated Fe-based alloy

In this research, the effects of thermomechanical treatment including heavy cold rolling and post-deformation annealing on the improvement of shape recovery in an Fe–9Ni–7Mn (at.%) martensitic alloy were investigated. Experimental results showed that the 80 % cold rolling produced a little fraction of strain-induced austenite phase in the martensitic matrix due to the strain concentration in the microstructure and the temperature rise under deformation. During post-deformation annealing at 590 °C in a dual phase (α+γ) region, a greater fraction of the austenite was introduced in the martensitic matrix such that its amount first increased by increasing the annealing time to 1.8 ks and then decreased at a more time of reversion. The microstructural evolution revealed that the austenite reversion under post-deformation annealing initially occurred by a shear nature at the early steps of reversion and then continued by diffusion. Tensile testing represented a good mixture of a relatively high ultimate tensile strength of ∼780 MPa and proper ductility of ∼8.5 % in the post-deformation annealed (PDA) sample for 0.9 ks. In addition, the shape memory properties were examined under the conditions of cold rolling and post-deformation annealing. The results showed a maximum shape recovery rate of ∼23 % for the cold rolled specimen which increased to ∼50 % after post-deformation annealing for 0.9 ks. The presence of a relatively high amount of retained austenite with proper stability and strength in the microstructure of the PDA sample for 0.9 ks was the reason for achieving the highest value of shape recovery.

A novel approach to suppression of reverted austenite in aerospace grade thick maraging steel weldments using the turbo-TIG welding process

This research examines aerospace grade-maraging steel weldments produced by the novel Turbo-TIG welding technique. The vital challenge in welding maraging steel is the development of reverted austenite in the weld region and HAZ. This reverted austenite degrades the mechanical characteristics of weldments. MDN 250 maraging steel with a 12 mm thick plate was welded at a high speed of 300 mm/min with consistent quality using the Turbo-TIG welding technique. The objective of the present work is to suppress the reverted austenite in the 12 mm thick plate of MDN 250 using the Turbo-TIG welding technique. Three different postweld heat treatments were applied, namely, (i) aging heat treatment (AT), (ii) solutionizing + aging (ST), and (iii) homogenization + solutionizing + aging (HT). The microstructure and X-ray diffraction analysis of the weld zone under AT and ST conditions demonstrate the existence of reverted austenite in the grain boundary regions. The SEM/EDS analysis of the weld zone of welded, AT, and ST conditions indicated Ni, Mo, and Ti microsegregation from the center matrix to the grain boundary regions. In contrast, neither microsegregation nor austenite reversion occurred in the HT condition. The tensile test demonstrates a maximum strength of 1797 MPa (UTS) under HT conditions. Likewise, the microhardness of the HT conditions exhibits a higher hardness of 552 HV in the fusion zone. In light of the metallurgical and mechanical characteristics of the weld, the HT heat treatments provide better weld performance in the case of Turbo-TIG welding of maraging steel grade MDN 250.