Application Of Spectroscopy Research Articles

Enhancing Structural Integrity, Optical Properties, and Room Temperature Formaldehyde Sensing Through Optimized Spray Deposition Rates

This study explores the impact of deposition rate on the properties of TiO2 thin films produced via spray pyrolysis, focusing on their application in gas sensors. The analysis covers structural, morphological, optical, and gas sensing characteristics of TiO2 films deposited at rates between 1 and 2.5 ml min−1. Studies show optimizing TiO2 film deposition rates at 2 ml min−1 significantly enhances formaldehyde detection, improving selectivity and achieving a rapid response of 7.52 at 20 ppm concentration. This study underscores the pivotal role of deposition rate optimization in augmenting the gas-sensing efficacy of TiO2 films, particularly for formaldehyde detection at ambient conditions. Optimal deposition rates are instrumental in enhancing sensor performance. The synergistic application of XRD and Raman spectroscopy unequivocally confirmed the presence of the TiO2 anatase phase, which is of paramount significance in gas sensing applications. FESEM furnished high-resolution insights into the surface morphology, revealing a spherical architecture. Furthermore, UV–vis spectroscopy was employed to assess the optical band gap of the films, which exhibited a decrement correlating with the rate of deposition. Notably, a deposition rate of 2 ml min−1 markedly improved the TiO2 films’ sensing performance. These insights are critical for developing cost-effective, high-performance gas sensors for cutting-edge applications.

Improved broadband luminescence in Gd2GaSb1-xTaxO7:Cr3+,Yb3+ pyrochlore phosphors: Near-infrared spectroscopic applications and dual-mode optical thermometry

The growing demand for spectroscopic applications in the fields of night vision monitoring, non-destructive analysis and bioimaging has led to extensive research into near infrared (NIR) light sources. Thus, the design of high-performance broadband Cr3+-doped NIR phosphors is of urgent and critical importance. Herein, novel Gd2GaSb1-xTaxO7:Cr3+,Yb3+ NIR-emitting pyrochlore phosphors were successfully explored. Via partly substituting Sb5+ by Ta5+ and tuning Cr3+ amount, a significant enhancement, broadening and redshift of Cr3+ NIR luminescence are exhibited under the radiation of 460 nm light. Moreover, higher thermal stability and wider NIR luminescence are realized by the proper introduction of Yb3+. A satisfactory NIR output power of 46.51 mW @ 300 mA and photoelectric efficiency of 10.82 % @ 10 mA of the fabricated NIR phosphor-converted light-emitting diodes (NIR pc-LEDs) based on Gd1.96Ga0.97Sb0.9Ta0.1O7:3%Cr3+,4%Yb3+ phosphor enable the demonstration in night vision and bioimaging applications. Besides, superior dual-mode optical thermometry was successfully constructed on fluorescence intensity ratio (Cr3+/Yb3+) and fluorescence lifetime (4T2) of Cr3+ in Gd2GaSb1-xTaxO7:Cr3+,Yb3+. These results confirm that Gd2GaSb1-xTaxO7:Cr3+,Yb3+ can serve as inspiring luminescent converters employed in NIR pc-LEDs and non-contact temperature sensing.

Polymer-integrated acoustic graphene plasmon resonator for sensitive detection of CO2 gas

Abstract Acoustic graphene plasmons exhibit an exceptional density of electromagnetic states within the mid-infrared and terahertz frequency ranges, leading to a pronounced near-field amplification and localization at the nanometer scale. This characteristic renders them highly promising for the development of ultra-sensitive plasmon-enhanced mid-infrared sensing and spectroscopic applications. However, the tight spatial confinement inherent to acoustic graphene plasmons results in a significant momentum mismatch, which in turn leads to poor coupling efficiency with light in free space. To overcome this limitation, we leverage numerical simulations to show that graphene plasmons can act as an intermediary to facilitate efficient excitation of acoustic graphene plasmons by incident mid-infrared radiation, achieving an extinction spectrum peak value of approximately 0.9. The proposed gas sensor based on the acoustic graphene plasmon resonator is composed of pristine, large-area graphene, an array of periodic metal nanocubes, and a slender polyethylenimine layer that adsorbs CO2, situated between the nanocubes and the graphene sheet. The sensing performance of the proposed sensor is numerically investigated. It is demonstrated that by incorporating a CO2-absorbing material into the acoustic graphene plasmons, we can perform highly sensitive assessments of the absorption bands within the polyethylenimine layer upon CO2 adsorption. The observed behavior of the acoustic graphene plasmons indicates a weakening and broadening with increasing CO2 concentrations, a phenomenon attributed to the alteration in the permittivity of the polyethylenimine in the interstitial layer due to CO2 adsorption. Numerical simulation results indicate that the sensitivity of the proposed hybrid gas sensor can reach up to 0.0183‰ ppm-1, which offers a remarkable 95-fold enhancement over the gas sensor based on graphene nanoribbons. Our findings underscore the potential of acoustic graphene plasmon nanoresonators as a transformative platform for ultrasensitive plasmon-enhanced sensing applications, particularly when integrated with various gas adsorption layers or molecular agents.

Application of High-Resolution Terahertz Spectroscopy for Studying Biofilms Typical of ENT Pathologies

Application of High-Resolution Terahertz Spectroscopy for Studying Biofilms Typical of ENT Pathologies

In2S3 nanoparticles modify the porous Fe2V4O13 nanostructure photoanode to enhance charge separation efficiency and photoelectrochemical water splitting performance

In this study, we demonstrate for the first time a promising photoanode of Fe2V4O13/In2S3 (FVO/IS) nanoparticles (NPs) for photoelectrochemical (PEC) water splitting. Most importantly, this work presents the first application of X-ray photoelectron spectroscopy in tracking electron flow direction within FVO/IS to reveal the formation of heterojunction having the electron flow from IS to FVO. Mott-Schottky measurement confirms that the modification of IS NPs establishes the type II heterojunction between FVO and IS, favorable for the transport and separation of carriers. Spectral measurements of electrochemical impedance spectroscopy, photoluminescence and Bode diagram confirm the effective separation of carriers and the prolongation of the charge lifetime in the FVO/IS heterojunction photoanode. Moreover, the electrochemical measurements evidently demonstrate the substantial enhancement in the charge separation efficiency (ηseparation) and charge transfer efficiency (ηtransfer) of the photoanode, leading to significantly enhanced PEC water splitting capability. As a result, in contrast with the pure FVO NPs photoanode, the photocurrent density of the constructed FVO/IS NPs photoanode is increased by 27 times without bias. This study paves a new approach for boosting the PEC water splitting activity of FVO photoanodes by constructing heterostructures through modification with other semiconductors.

Neonatal somatic oxygenation and perfusion assessment using near-infrared spectroscopy : Part of the series on near-infrared spectroscopy by the European Society of Paediatric Research Special Interest Group "Near-Infrared Spectroscopy".

In this narrative review, we summarize the current knowledge and applications of somatic near-infrared spectroscopy (NIRS), with a focus on intestinal, renal, limb, and multi-site applications in neonates. Assessing somatic oxygenation at various body locations in neonates may aid in the understanding of underlying pathophysiology of organ injury. Considering cerebral autoregulation may be active to protect the brain during systemic circulatory failure, peripheral somatic oxygenation may potentially provide an early indication of neonatal cardiovascular failure and ultimate hypoxemic injury to vital organs including the brain. Certain intestinal oxygenation patterns appear to be associated with the onset and course of necrotizing enterocolitis, whereas impaired renal oxygenation may indicate the onset of acute kidney injury after various types of hypoxic events. Peripheral muscle oxygenation measured at a limb may be particularly effective in the early prediction of shock in neonates. Using multi-site NIRS may complement current approaches and clinical investigations to alert for neonatal tissue hypoxemia, and potentially even guide management. However, somatic NIRS has its inherent limitations in regard to accuracy. Interpretation of organ-specific values can also be challenging. Last, currently there are limited prospective intervention studies, and clinical benefits need to be examined further, after the clarification of critical threshold-values. IMPACT: The assessment of somatic oxygenation using NIRS may contribute to the prediction of specific diseases in hemodynamically challenged neonates. Furthermore, it may give early warning signs for impending cardiovascular failure, and impaired cerebral circulation and oxygenation. We present a comprehensive overview of the literature on applications of NIRS to various somatic areas, with a focus on its potential clinical applicability, including future research directions. This paper will enable prospective standardized studies, and multicenter collaboration to obtain statistical power, likely to advance the field.

Surface-Enhanced Raman Spectroscopy of Ammonium Nitrate Using Al Structures, Fabricated by Laser Processing of AlN Ceramic

This work presents results on laser-induced surface structuring of AlN ceramic and its application in Surface-Enhanced Raman Spectroscopy (SERS). The laser processing is performed by nanosecond pulses in air and vacuum. Depending on the processing conditions, different surface morphology can be obtained. The ablation process is realized by ceramic decomposition as the formation of an aluminium layer is detected. The efficiency of the fabricated structures as active substrates in SERS is estimated by the ability of the detection of ammonium nitrate (NH4NO3). It is conducted for Raman spectrometer systems that operate at wavelengths of 514 and 785 nm where the most common commercial systems work. The obtained structures contribute to enhancement of the Raman signal at both wavelengths, as the efficiency is higher for excitation at 514 nm. The limit of detection (LOD) of ammonium nitrate is estimated to be below the maximum allowed value in drinking water. The analysis of the obtained results was based on the calculations of the near field enhancement at different conditions based on Finite Difference Time Domain simulation and the extinction spectra calculations based on Generalized Mie scattering theory. The structures considered in these simulations were taken from the SEM images of the real samples. The oxidation issue of the ablated surface was studied by X-ray photoelectron spectroscopy. The presented results indicated that laser structuring of AlN ceramics is a way for fabrication of Al structures with specific near-field properties that can be used for the detection of substances with high social impact.

Application of near-infrared spectroscopy to assess the effect of the cupping size on the spatial hemodynamic response from the area inside and outside the cup of the biceps.

Cupping therapy is a popular intervention for improving muscle recovery after exercise although clinical evidence is weak. Previous studies demonstrated that cupping therapy may improve microcirculation of the soft tissue to accelerate tissue healing. However, it is unclear whether the cupping size could affect the spatial hemodynamic response of the treated muscle. The objective of this study was to use 8-channel near-infrared spectroscopy to assess this clinical question by assessing the effect of 3 cupping sizes (35, 40, and 45 mm in inner diameter of the circular cup) under -300 mmHg for 5 min on the muscle hemodynamic response from the area inside and outside the cup, including oxyhemoglobin and deoxy-hemoglobin in 18 healthy adults. Two-way factorial design was used to assess the interaction between the cupping size (35, 40, and 45 mm) and the location (inside and outside the cup) and the main effects of the cupping size and the location. The two-way repeated measures ANOVA demonstrated an interaction between the cupping size and the location in deoxy-hemoglobin (P = 0.039) but no interaction in oxyhemoglobin (P = 0.100), and a main effect of the cup size (P = 0.001) and location (P = 0.023) factors in oxyhemoglobin. For the cupping size factor, the 45-mm cup resulted in a significant increase in oxyhemoglobin (5.738±0.760 μM) compared to the 40-mm (2.095±0.312 μM, P<0.001) and 35-mm (3.134±0.515 μM, P<0.01) cup. Our findings demonstrate that the cupping size and location factors affect the muscle hemodynamic response, and the use of multi-channel near-infrared spectroscopy may help understand benefits of cupping therapy on managing musculoskeletal impairment.

Development of a Multiplexing Injector for Gas Chromatography for the Time-Resolved Analysis of Volatile Emissions from Lithium-Ion Batteries

Multiplex sampling, so far mainly used as a tool for S/N ratio improvement in spectroscopic applications and separation techniques, has been investigated here for its potential suitability for time-resolved monitoring where chromatograms of transient signals are recorded at intervals much shorter than the chromatographic runtime. Different designs of multiplex sample introduction were developed and utilized to analyze lithium-ion battery degradation products under normal or abuse conditions to achieve fast and efficient sample introduction. After comprehensive optimization, measurements were performed on two different GC systems, with either barrier discharge ionization detection (BID) or mass spectrometric detection (MS). Three different injector designs were examined, and modifications in the pertinent hardware components and operational conditions used. The shortest achievable sample introduction time was 50 ms with an interval of 6 s. Relative standard deviations were lower than 4% and 10% for the intra- and inter-day repeatability, respectively. The sample introduction system and column head pressure had to be carefully controlled, as this parameter most critically affects the amount of sample introduced and, thus, detector response. The newly developed sample introduction system was successfully used to monitor volatile degradation products of lithium-ion batteries and demonstrated concentration changes over the course of time of the degradation products (e.g., fluoroethane, acetaldehyde and ethane), as well as for solvents from the battery electrolyte like ethyl carbonate.

Opportunities and Challenges: Process Raman for the Real-Time Release Testing (RTRT) of Extended-Release Formulations

The use of a process analytical technology has been demonstrated using near-infrared spectroscopy for continuous manufacturing of pharmaceutical formulations and is within the scope of the U.S. Food and Drug Administration's real-time release testing initiative. While effective for simple formulations, this preliminary study investigates whether such a spectroscopic surrogate application can replace pharmaceutical dissolution testing for extended-release formulations. In this study, we will assess the use of process Raman spectroscopy for real-time dissolution testing. Extended-release tablet formulations often accomplish the release rate delay through the addition of gelling agents. In this work, hydroxypropyl methylcellulose (HPMC) polymers were used to formulate extended-release niacin tablets. Process Raman spectroscopy was evaluated as a tool to effectively model dissolution profiles to determine if the optical technique has the ability to differentiate HPMC polymers from the background and be selective for the polymer type employed. Our preliminary work indicates that while Raman can effectively detect and monitor the niacin response of the tablet formulations, there are not enough unique spectral features between the different HPMC polymers to selectively resolve their responses. Additional measurements and chemometric analysis might suggest otherwise. Thus, for extended-release tablet applications with continuous manufacturing, further dissolution surrogate development is needed.

Intense NIR-II luminescence through stabilization of tetrahedral (Mn5+O4) lumophore in apatites with high external quantum efficiency

The discovery of highly efficient near-infrared (NIR) emitting phosphors is essential for multiple spectroscopic applications. Pentavalent-manganese (Mn5+) is a rarely-reported NIR-II activator due to the its instability in inorganic solids. In this study, Mn5+-activated apatite phosphors A5(B1-xMnxO4)3X (A = Sr, Ba; B = P, V; X = OH, F, Cl, Br) were reported. Benefiting from the discrete P/VO4 tetrahedron and stabilization effect of alkaline-earth cation, Mn5+ existed as MnO43− anion can be effectively incorporated into the A5(P/VO4)3X. A selection of 16 different apatites is conducted to test the structural and compositional effect on Mn5+ stabilization and luminescence. The structure-property relationship was discussed with a detailed analysis on Mn5+ Tanabe-Sugano diagram and Dq/B calculation. Particularly, the optimized Ba5(VO4)3Cl: 0.01Mn5+ (λex = 650 nm, λem = 1181 nm) reveals an exceptional external quantum efficiency of 61.1 % with vivid turquoise body color. The multiparametric thermometry by luminescence intensity ratio (LIR) and 1E lifetime were demonstrated with excellent linear regressions (R2 > 99.9 %) and high relative sensitivities of > 1.0% K−1 in the range of physiological temperatures. A NIR-II phosphor-converted light-emitting diode (pc-LED) is fabricated with a NIR output power of 30.18 mW at 60 mA driven current and photoelectric conversion efficiency of 6.63 %.

Applications of Functional Near-Infrared Spectroscopy (fNIRS) Neuroimaging During Rehabilitation Following Stroke: A Review

Applications of Functional Near-Infrared Spectroscopy (fNIRS) Neuroimaging During Rehabilitation Following Stroke: A Review

Controlling Chirogenic Effects in Porphyrin Based Supramolecular Systems: Theoretical Analysis Versus Experimental Observations.

Electronic circular dichroism (ECD) spectroscopy is a widely employed method for studying chiral analysis, requiring the presence of a chromophore close to a chiral centre. Porphyrinoids are found to be one of the best chromophoric systems serving for this purpose and enabling the application of ECD spectroscopy for chirality determination across diverse classes of organic compounds. Consequently, it is crucial to understand the induction mechanisms of ECD in the porphyrin-based complexes. The present study explores systematically the influence of secondary chromophores, bonded to an achiral zinc porphyrin or to chiral guest molecules, on the B-region of ECD spectra using the time-dependent density functional theory (TD-DFT) calculations. The study analyses the impact of change in both the conformation of achiral porphyrin (host) and change in position and conformation of chiral organic molecule (guest) on the B-band of ECD spectra (energy, intensity, sign of Cotton effect). Finally, conclusions made on model complexes are applied to published experimental data, contributing to a deeper understanding of various factors influencing ECD spectra in chiral systems. In addition, a computer program aimed to help rationalise ECD spectra by visualizing corresponding orbital energies, rotatory strengths, electric and magnetic transition moments, and angles between them, is presented.

Applications of magnetic resonance spectroscopy in diagnosis of neurodegenerative diseases: A systematic review

BackgroundMagnetic resonance spectroscopy (MRS) is an imaging technique used to measure metabolic changes in the tissue. Due to the lack of evidence, MRS is not a priority in diagnosing neurodegenerative diseases because it is a relatively specialized technique that requires specialized equipment and expertise to perform and interpret. This systematic review aimed to present a comprehensive collection of MRS results in the most common neurodegenerative diseases. MethodsA systematic search of four electronic databases (PubMed, Scopus, Web of Science, and ScienceDirect) was conducted for studies published from 2017 to 2022. Articles that provided specific biomarker levels were selected, and studies that assessed the diseases via treatment, featured MRS applying nuclei other than 1H, or compared different animal models were excluded. ResultsA total of 25 articles, plus 3 articles for extra information in the introduction, were included in this review. Six of the most common neurodegenerative diseases, i.e., Alzheimer's and Parkinson's disease, Huntington chorea, ataxia, multiple sclerosis (MS), multiple system atrophy (MSA), and progressive supranuclear palsy (PSP) were examined via MRS. The changes and ratios of N-acetylaspartate (NAA) could be seen in all of these disorders, which could lead to early diagnosis. However, there are other biomarkers, such as Cr and Chon, which can give convincing results. DiscussionThis observational study is the first synthesis of the latest evidence proving metabolic changes during neurodegenerative diseases using MRS as a diagnosis method. The findings indicate decreased N-acetylaspartate (NAA) and NAA/Cr ratios in Alzheimer's disease (AD), Parkinson's disease (PD), ataxias, and MS, reflecting neuronal loss or dysfunction. Increased choline and myo-inositol were noted in some studies, suggesting cell membrane turnover and neuroinflammation. Findings were less consistent for other metabolites like glutamate and gamma-aminobutyric acid. However, there were limitations due to the lack of studies on the same volumes of interest (VOIs) and the small number of participants.

Effect of Sample Presentation on the Classification of Black Soldier Fly Larvae Using Near-Infrared Spectroscopy

Black soldier fly larvae (BSFL) (Hermetia illucens) reared on food waste streams are considered a sustainable source of protein in feed livestock diets. Recently, portable near-infrared spectroscopy (NIR) instruments have been assessed to monitor the consistency and quality of food waste streams used to feed black soldier fly larvae. During the application of NIR spectroscopy, sample presentation (e.g., drying, processing, particle size) plays an important role in the accuracy of the models developed (quantitative or qualitative analysis). The objective of this study was to evaluate the effect of sample presentation (number of larvae used during the scanning of BSFL) on the accuracy of classification models developed to trace the food waste stream (e.g., supermarket of childcare) used to feed the larvae. BSFL samples were sourced from two waste streams and scanned as half, 1, 2, or 3 larvae using an NIR portable instrument (MicroNIR, Viavi, Milpitas, California, USA). Principal component analysis (PCA) and linear discriminant analysis (LDA) were used to analyze the NIR data and to classify the samples according to the waste stream. The main differences in the NIR spectra of the BSFL samples associated with the number of larvae scanned were observed around 1200 nm, mainly associated with the C-H overtones (lipids). The classification results showed that high classification rates (&gt;93%) were obtained regardless of the number of larvae scanned, ranging from 93% (using 0.5 larvae) to 100% (using 1, 2, or 3 larvae samples). Overall, the number of larvae scanned had minimal to no effect on the accuracy of the LDA classification models. The present study demonstrated that a portable NIR instrument can be suitable for an initial rapid classification or determination of the origin of the waste stream used to feed the BSFL.

Engineering tRNAs for the Ribosomal Translation of Non-proteinogenic Monomers.

Ribosome-dependent protein biosynthesis is an essential cellular process mediated by transfer RNAs (tRNAs). Generally, ribosomally synthesized proteins are limited to the 22 proteinogenic amino acids (pAAs: 20 l-α-amino acids present in the standard genetic code, selenocysteine, and pyrrolysine). However, engineering tRNAs for the ribosomal incorporation of non-proteinogenic monomers (npMs) as building blocks has led to the creation of unique polypeptides with broad applications in cellular biology, material science, spectroscopy, and pharmaceuticals. Ribosomal polymerization of these engineered polypeptides presents a variety of challenges for biochemists, as translation efficiency and fidelity is often insufficient when employing npMs. In this Review, we will focus on the methodologies for engineering tRNAs to overcome these issues and explore recent advances both in vitro and in vivo. These efforts include increasing orthogonality, recruiting essential translation factors, and creation of expanded genetic codes. After our review on the biochemical optimizations of tRNAs, we provide examples of their use in genetic code manipulation, with a focus on the in vitro discovery of bioactive macrocyclic peptides containing npMs. Finally, an analysis of the current state of tRNA engineering is presented, along with existing challenges and future perspectives for the field.

Decoration of Ag nanoparticle on MXene sheets for SERS studies

MXene sheets with the unique electrical and optical properties show the excellent potential for surface-enhanced Raman spectroscopy (SERS) applications. In this study, we chose Ti3C2Tx, a type of MXene, to decorate silver nanoparticles (Ag NPs) on the ultrathin two-dimensional (2D) MXene sheets. The designed Ag-MXene substrates with SERS activity showed high sensitivity, high stability, and reproducibility. The SERS signal was enhanced by the synergistic contribution of both charge-transfer (CT) and surface plasmon resonance (SPR) involving the Ag NPs and the MXene sheets. Due to the strong interaction between the probe molecules and Ag NPs which provided the nanoscale gap, the substrate exhibited remarkable SERS performance. A novel experimental strategy was developed to facilitate the controlled synthesis of noble metal NPs and MXene sheets and provide insights for further improving the practical applications of these materials in SERS detection.

Identification of Some Gem-Quality Red and Green Feldspars

Sunstone is a member of the feldspar group. Natural sunstones from Oregon exhibit unique optical effects and hold significant market value. However, since 2008, there has been a persistent issue of diffused red feldspars masquerading as natural sunstones in the market, severely undermining consumer confidence in purchasing natural sunstones. Fluorescence characteristics under 305–335 nm ultraviolet excitation are considered an effective method for distinguishing copper-diffused red feldspars from natural sunstones. In this paper, through detailed analysis and testing of ten market-acquired red and green feldspar samples, including UV-vis spectra, microscopic characteristics, fluorescence spectra, and chemical compositions, we validate the efficacy of fluorescence characteristics in identifying copper-diffused feldspars. The results verify the widespread prevalence of copper diffusion treatment in market-acquired red and green feldspars, shedding light on their treatment history and providing valuable insights for jewelry consumers. This research not only enhances our understanding of sunstone treatments but also strengthens the reliability and applicability of fluorescence spectroscopy in gemstone identification, offering promising prospects for its broader adoption in the jewelry market.

Prediction of Density in Standing Trees of Various Wood Species in Natural Forests Using Near-infrared Spectroscopy

Density plays an important role as basic information for applying wood as construction materials. Recent years, the application of near-infrared spectroscopy as non-destructive testing (NDT) has been promising. Density prediction for standing trees in huge variation trees and species of natural forest needs to be investigated using NDT as of eco-green harvesting. The combination of density information and near-infrared spectroscopy is enabled to build a prediction model. This research applied increment cores sampling for density prediction analysis using near-infrared spectroscopy method. The research combined increment cores samples from multiple wood species to be analyzed in one chemometrics analysis of cross-validation partial least squares regression (CV-PLSR) to build a prediction model of density. The research resulted coefficient of determination for cross-validation (R2CV) of 0.76 with number of latent variable (LV) 10 from the 1st derivative with 13 smoothing-point spectra and wavelength of 1200 – 1800 nm as the best prediction model. The result seemed sufficient enough with those number of LV for this small tube wood sampling of increment cores from multiple wood species. This research proved that building a prediction model for multiple wood species is possible to be done.

Intra-oscillator high harmonic source reaching 100-eV photon energy

Resonant enhancement inside an optical cavity has been a wide-spread approach to increase efficiency of nonlinear optical conversion processes while reducing the demands on the driving laser power. This concept has been particularly important for high harmonic generation XUV sources, where passive femtosecond enhancement cavities allowed significant increase in repetition rates required for applications in photoelectron spectroscopy, XUV frequency comb spectroscopy, including the recent endeavor of thorium nuclear clock development. In addition to passive cavities, it has been shown that comparable driving conditions can be achieved inside mode-locked thin-disk laser oscillators, offering a simplified single-stage alternative. This approach is less sensitive to losses thanks to the presence of gain inside the cavity and should thus allow higher conversion efficiencies through tolerating higher intensity in the gas target. Here, we show that the intra-oscillator approach can indeed surpass the much more mature technology of passive enhancement cavities in terms of XUV flux, even reaching comparable values to single-pass sources based on chirped-pulse fiber amplifier lasers. Our system operates at 17 MHz repetition rate generating photon energies between 60 eV and 100 eV. Importantly, this covers the highly attractive wavelength for the silicon industry of 13.5 nm at which our source delivers 60 nW of outcoupled average power per harmonic order.