Incident Angle Research Articles

A Dual-Band Polarization-Insensitive Frequency Selective Surface for Electromagnetic Shielding Applications

This paper presents a novel polarization-insensitive dual-band frequency-selective surface (FSS)-based electromagnetic shield. The miniaturized FSS unit cell consists of a modified Jerusalem crossed loop and a corner-modified square loop. These FSS elements are arranged in a co-planner configuration over a single-layer Rogers 5880 substrate and simultaneously offer effective shielding in the X- and Ku-bands. Moreover, the FSS manifests polarization-independent and angularly stable band-reject filter characteristics over various oblique angles of incidence for both the TE and TM polarizations with virtuous attenuation at both resonances. In addition, the FSS structure is modelled into an equivalent lumped circuit to better analyze the phenomenon of EM wave suppression. A finite prototype of FSS is fabricated and tested. The simulated and measured results are in good agreement, thus making it a potential candidate for RF shielding/isolation applications.

Study on the Seismic Response of a Water-Conveyance Tunnel Considering Non-Uniform Longitudinal Subsurface Geometry and Obliquely Incident SV-Waves

The longitudinal seismic response characteristics of a shallow-buried water-conveyance tunnel under non-uniform longitudinal subsurface geometry and obliquely incident SV-waves was studied using the numerical method, where the effect of the non-uniform longitudinal subsurface geometry due to the existence of a local one-sided rock mountain on the seismic response of the tunnel was focused on. Correspondingly, a large-scale three-dimensional (3D) finite-element model was established, where different incidence angles and incidence directions of the SV-wave were taken into consideration. Also, the non-linearity of soil and rock and the damage plastic of the concrete lining were incorporated. In addition, the wave field of the site and the acceleration response as well as damage of the tunnel were observed. The results revealed the following: (i) a local inclined subsurface geometry may focus an obliquely incident wave due to refraction or total reflection; (ii) a tunnel in a site adjacent to a rock mountain may exhibit a higher acceleration response than a tunnel in a homogeneous plain site; and (iii) damage in the tunnel in the site adjacent to a rock mountain may appear in multiple positions, and the effect of the incidence angle on the mode of compressive deformation and damage of the lining is of significance.

Historical Evolution of the Impact of Seismic Incident Angles on the Safety Assessment of Various Building Construction Typologies

In the existing building stock, typically characterised by a high degree of irregularity, the effects of earthquakes are strongly dependent on the epicentre–structure direction and the angle of incidence of the seismic motion. However, the scientific community has not yet reached a unanimous consensus on the evaluation of the effects of seismic incidence angles. Therefore, this paper conducts an extensive investigation of the international literature on current methods to consider seismic directionality, systematically reviewing more than 80 publications on this topic. Following a brief overview of the problem and an analysis of the initial developments of the multidirectionality concept of seismic input, a state-of-the-art review is presented based on the considered analysis methods, specifically response spectrum analysis, nonlinear static analysis, and nonlinear response history analysis. Moreover, the adoption of multidirectional seismic input in popular codes and standards is presented and discussed. This study provides the first comprehensive synthesis of research on the seismic incidence angles across diverse building typologies, offering crucial insights for future code revisions and highlighting significant gaps in current analytical methods and standards, thereby setting a new direction for subsequent empirical investigations. Specifically, the extensive state-of-the-art review revealed that, until now, the evaluation of the angle of incidence was primarily conducted on existing reinforced concrete buildings with a limited number of storeys, analysed with nonlinear response history analysis. This underscores the need for future research to extensively investigate the impact of the angle of incidence on other types of construction typologies.

Composite Electromagnetic Scattering Characteristics of Actual Terrain and Moving Rockets

This research involved studying the characteristics of composite electromagnetic scattering from a rocket moving above actual terrain using the finite-difference time-domain method. The angular distribution curve of the composite scattering coefficient was obtained, and the influences of factors such as the angle of incidence, the frequency of the incident electromagnetic wave, the content of moisture in soil, the dielectric constant of the rocket-shell material, the height of the rocket, and the undulation of the terrain on the composite scattering coefficient were investigated. Results show that the composite scattering coefficient oscillates with the scattering angle and increases in the direction of mirror reflection. It also decreases with increasing angle of incidence, frequency of the incident wave, and altitude of the rocket, while it increases with increasing soil moisture and dielectric constant of the rocket-shell materials. Although the influence of different terrain undulations on the composite scattering coefficient is noticeable, it follows no fixed pattern.

The initial sticking of high velocity water onto graphite under non-equilibrium supersonic flow conditions.

In this paper, we present a combined experimental and theoretical study that explored the initial sticking of water on cooled surfaces. Specifically, these ultra-high vacuum gas-surface scattering experiments utilized supersonic molecular beam techniques in conjunction with a cryogenically cooled highly oriented pyrolytic graphite crystal, giving control over incident kinematic conditions. The D2O translational energy spanning 300-750meV, the relative D2O flux, and the incident angle could all be varied independently. Three different experimental measurements were made. One involved measuring the total amount of D2O scattering as a function of surface temperature to determine the onset of sticking under non-equilibrium gas-surface collision conditions. Another measurement used He specular scattering to assess structural and coverage information for the interface during D2O adsorption. Finally, we used time-of-flight (TOF) measurements of the scattered D2O to determine how energy is exchanged with the graphite surface at surface temperatures above and near the conditions needed for gaseous condensation. For comparison and elaboration of the roles that internal degrees of freedom play in this process, we also did similar TOF measurements using another mass 20 incident particle, atomic neon. Enriching this study are precise molecular dynamics simulations that elaborate on gas-surface energy transfer and the roles of molecular degrees of freedom in gas-surface collisional energy exchange processes. This study furthers our fundamental understanding of energy exchange and the onset of sticking and ultimately gaseous condensation for gas-surface encounters occurring under high-velocity flows.

A Proposal for a Solar Position Sensor System with Multifiber Optical Cable

A solar position sensor is an essential optoelectronic device used to monitor the sun’s position in solar tracking systems. In closed-loop systems, this sensor is responsible for providing feedback signals to the control system, allowing motor adjustments to optimize the angle of incidence and minimize positioning errors. The accuracy required for solar tracking systems varies depending on the specific photovoltaic concentration. In the case of the concentrator photovoltaic (CPV), it is normally essential to track the sun with a position error of less than ±0.6°. To achieve such precision, a proposed sensor configuration composed of low-cost embedded electronics and multifiber optical cable is subjected to characterization through a series of measurements covering range, sensitivity, and resolution. These measurements are performed in controlled indoor environments as well as outdoor conditions. The results obtained exhibit a resolution of 2.6×10−3 degrees when the sensor is illuminated within its designated field of view of ±0.1°, particularly in external conditions. Considering the performance demonstrated by the proposed solar position sensor, coupled with its straightforward modeling and assembly compared to position sensors documented in the literature, it emerges as a promising candidate for integration into solar tracking systems.

Wave type fiber SPR sensor for rapid and highly sensitive detection of hyperoside

The fiber surface plasmon resonance (SPR) sensor used for the detection of active ingredients in traditional Chinese medicine has the problems of low sensitivity and difficult specific recognition. This paper proposed a wave type fiber SPR sensor, which reduced the mode of transmitted light through a periodic wave structure and caused concentrated and total reflection of the transmitted beam at the interface between the bent peak cladding and the air. A 50 nm gold film was coated on the surface of the cladding in the wave structure area to form the SPR sensing area. By controlling the width and height of the wave structure to control the total reflection angle of the transmitted light, i.e., the SPR incidence angle, the sensitivity of the fiber SPR sensor was effectively improved to 4972 nm/RIU. Furthermore, HSP90AA protein was modified on the gold film of the sensor to achieve specific detection of hyperoside. The longest single detection time was only 3 minutes, and the detection sensitivity was 0.53 nm/(µg/ml), with a detection limit as low as 0.68µg/ml, which is comparable to liquid chromatography. The proposed wave type fiber SPR sensor is fast in production and has high structural mechanical strength, providing a new approach for the rapid, highly sensitive, and specific detection of active ingredients in traditional Chinese medicine.

Silicon-based ultra-broadband mid-IR and LWIR near-perfect metamaterial absorber

Ultra-broadband metamaterial absorbers (UBMAs) that are compatible with CMOS technology for use in the mid-infrared and long-wave infrared regions are crucial for a variety of applications, including radiative cooling, thermal photovoltaic, and thermal imaging. In this regard, we propose, in this work, a design of an UBMA based on the heavily doped silicon (D-Si) and silicon carbide (SiC). The 3D finite-difference time-domain method is used, mainly, to numerically calculate the optical characteristics of the proposed UBMA. The absorber, which is made up of a periodic array of symmetrical multilayered square rings of D-Si and SiC, achieves high absorption with an average absorption of 95% over a wavelength range of 2.5–22 µm. This broad range of wavelength absorption is attained, encompassing the mid-, long-wave, and partial far-infrared regions. In addition to the materials' inherent absorption, the stimulation of magnetic polaritons, surface plasmon polaritons, localized surface plasmon resonance, and cavity resonance are responsible for the nearly perfect broadband absorption. Under normal incidence, the proposed UBMA is polarization-independent due to the symmetrical design of the absorber. Furthermore, the impact of the incidence angle on the absorption of transverse electric and transverse magnetic waves is examined.

Effect of distributed Bragg reflectors on optoelectronic characteristics of GaN-based flip-chip light-emitting diodes

Abstract Distributed Bragg reflectors have been widely utilized in GaN-based flip-chip light-emitting diodes (FCLEDs) owing to their excellent reflection performance. Recently, wide reflected angle DBR (WRA-DBR) has been suggested to enhance the optical characteristics of GaN-based FCLEDs by incorporating multiple sub-DBRs with varying central wavelengths. However, the reflectivity of WRA-DBR decreases at large incident angle from 425 nm to 550 nm, which restricts further optical performance improvement of FCLEDs. Here, we demonstrate a quintuple-stack DBR comprised of five sub-DBRs. The quintuple-stack DBR possesses a high reflectivity (>97.5%) for incident angles below 50° within the blue and green light wavelength ranges. Compared to WRA-DBR, quintuple-stack DBR exhibits a higher reflectivity in wavelength range of 425 nm to 550 nm and thinner multilayer thicknesses. Furthermore, stronger electric field intensities exist in the top facet and sidewalls of FCLED with quintuple-stack DBR, revealing that quintuple-stack DBR is beneficial for enhancing the light extraction efficiency. As a result, the light output power of FCLED with quintuple-stack DBR is ~3% higher than that of FCLED with WRA-DBR at 750 mA.

Radiographic Alignment Parameters for Lumbosacral Reconstruction in Patients With Altered S1 Morphology.

Retrospective quantitative analysis study. Pelvic incidence has been established as central radiographic marker which determines patient-specific correction goals during surgery for adult spinal deformity. In cases with sacral doming or sacral osteotomy where the PI cannot be calculated, reliable radiographic parameters need to be established to determine surgical goals. We aim to determine multiple radiographic parameters and formulas that can be utilized when the S1 superior endplate is obscured. Retrospective analysis was performed on 68 healthy volunteers without prior spine surgery with full-length radiographs. Pelvic incidence, sacral slope, and pelvic tilt were calculated for each patient. Additional measurements such as L4, L5, and S2 incidence, tilt, and slope were collected. A new radiographic parameter defined as the L4-Sciatic notch angle was measured. Regression analysis was performed on each value to determine its relationship with S1 based incidence, tilt, and slope. Mean values for L5 incidence, L4 incidence, and L4 sciatic notch angle were 21.8° ± 8.9, 4.4° ± 8.1, and 44.4° ± 12, respectively. The linear regression analysis produced the following formulas which can be utilized to determine deformity correction goals when pelvic incidence can be calculated pre-operatively: L5i = .65*S1i-11.4, L4i = .44*S1i-18.6, and L4SNA = -.34*S1i + 66.5. In settings where pelvic incidence cannot be calculated, the following formulas can be utilized: L5i = .66*S2i-32.3 and L4SNA = -.02*S2i2 + 1.1*S2i + 63.5. P-values for all regression analyses were <.001. This study provides target radiographic alignment values that can be utilized for patients with either pre-operative altered S1 endplates or in cases with intraoperative alteration of S1 (sacral osteotomy).

Scattering properties of dual Bessel beams on chiral layered particle

The paper investigates the scattering analytical solution of arbitrary direction double zero-order Bessel beams (ZOBBs) incident on a non-uniform layered chiral sphere. Using the generalized Lorenz-Mie theory (GLMT), the electromagnetic field expansion expression of the double ZOBBs is obtained through the vector superposition of the spherical vector wave functions (SVWFs). Analytical solutions of the scattering on chiral layered particles by dual Bessel beams are derived based on the boundary condition. The iterative coefficient equations are constructed to obtain the expansion coefficients of the SVWFs in each region of the multi-layer chiral sphere. The variation of radar cross section (RCS) with angular distribution is numerically simulated, and the scattering results of layered chiral spheres degenerated into isotropic layered spheres are compared with the literature, which verifies the correctness of the theory and program. The effects of incident angle, polarization angle, cone angle and chiral parameters on the scattering characteristics of far region and internal field of the layered chiral particle are analyzed in detail. The theory and results can offer significant assistance in studying the optical properties of non-uniform chiral particles and complex biological cells irradiated by multiple beams and may also provide important practical value in the micromanipulation of multi-layered biological structures.

Numerical investigation of acoustic streaming vortices in cylindrical tube arrays

Abstract Acoustic streaming has a significant effect on accelerating material mixing and flow field disturbance. To explore the characteristics of acoustic streaming in the cylindrical tube array field under the action of an acoustic wave, we derive the dimensionless acoustic streaming control equation and establish a numerical calculation model of acoustic streaming. The effects of acoustic incidence angle, acoustic Reynolds number, and Strouhal number on the acoustic streaming vortex flow field in the tube array were investigated. The numerical results show that with the change in acoustic parameters, the acoustic streaming in the tube array presents rich changes in the vortex flow field, and there are flow field phenomena such as shrinking, merging, tearing, and splitting of the vortex structure. Toward the walls of each tube, there is a strong acoustic streaming flow velocity. Besides, there is also a large streaming velocity on the interface of the adjacent acoustic streaming vortices. The inner streaming vortex structure in the acoustic boundary layer decreases with the increase in the acoustic Reynolds number, but the intensity of the inner streaming vortex and outer streaming vortex increases rapidly, and the disturbance effect of the flow field is enhanced. With the increase in the dimensionless acoustic frequency (or Strouhal number), although the structure and intensity of the inner streaming vortex decrease, the velocity gradient on the wall of the cylindrical tube increases, which is beneficial to destroy the flow boundary layer of the cylindrical tube wall and accelerate the instability of the wall flow field.

Research on electronic optical monitoring technology and system design for vacuum electron beam welding process

Electron beam welding technology is increasingly used in industrial manufacturing due to its high power density and the purity of welded joints. In vacuum environments, traditional optical and machine vision monitoring methods are susceptible to contamination by metal vapors, which hinders the monitoring effect. Due to the limitations of optical monitoring methods, electronic optical imaging technology is a new alternative monitoring method that has been introduced into the electron beam processing in recent years, but the complexity of the industrial electron beam welding environment makes it relatively less studied in the field of electron beam welding. In this study, a YAG scintillator detector is proposed to collect the backscattered electron information generated by the interaction of electrons with the sample, and an FPGA real-time processing system is used to realize the weld quality monitoring in the industrial electron beam welding processes. The distribution law of backscattered electrons in space is simulated by Monte Carlo method, and the results show that the number of distribution in the 40°∼60° angle region is more, the backscattering coefficient increases with the increase of the incident angle of the electron beam, and the backscattering coefficient of the samples with large atomic numbers is relatively high. The field monitoring experiments show that the designed system exhibits good sensitivity to the characteristic morphology, and the imaging resolution reaches more than 200 μm, and the weld hole defects are clearly visible. A good linear correlation between the current change curve during scanning and the actual shape profile is shown, while the image resolution is better when the spot current is 1 mA.

Alleviating the Angular Dependence of Perovskite Solar Cells via Light‐Harvesting Nanostructure

Over the past decade, perovskite solar cells (PSCs) have witnessed a remarkable surge in power conversion efficiency (PCE). However, the electrical output performance of PSCs is dependent on the incident angle of solar radiation, and energy loss occurs during photovoltaic conversion when light impinges at angles. Herein, a perovskite‐light‐absorbed layer with inverse opal structure is used to fabricate PSCs and reduce the angular dependence of the performance. In the results, it is demonstrated that ordered periodic perovskite inverse opal (PVSK–IO) not only exhibits a remarkable slow‐photon effect for enhancing the absorption of sunlight near the photonic bandgap (PBG), but also promotes the carrier transfer by expanding the contact area with hole‐transport layer. Moreover, the slow‐photon region of PBG can be intentionally tuned by changing the direction of sunlight illumination, thereby more intuitively delaying and storing light in the PVSK–IO layer. As a consequence, the slow‐photon effect originated from the PVSK–IO structure efficiently improves the short‐circuit current density, resulting in a higher PCE than that of planar devices under the irradiation from different incident angles. In this research, a rational strategy is offered for enhancing the performance of PSCs while alleviating their angular dependence.

Reconstructing the reflectivity of liquid surfaces from grazing incidence X-ray off-specular scattering data

The capillary wave model of a liquid surface predicts both the X-ray specular reflection and the diffuse scattering around it. A quantitative method is presented to obtain the X-ray reflectivity (XRR) from a liquid surface through the diffuse scattering data around the specular reflection measured using a grazing incidence X-ray off-specular scattering (GIXOS) geometry at a fixed horizontal offset angle with respect to the plane of incidence. With this approach the entire Qz -dependent reflectivity profile can be obtained at a single, fixed incident angle. This permits a much faster acquisition of the profile than with conventional reflectometry, where the incident angle must be scanned point by point to obtain a Qz -dependent profile. The XRR derived from the GIXOS-measured diffuse scattering, referred to in this paper as pseudo-reflectivity, provides a larger Qz range compared with the reflectivity measured by conventional reflectometry. Transforming the GIXOS-measured diffuse scattering profile to pseudo-XRR opens up the GIXOS method to widely available specular XRR analysis software tools. Here the GIXOS-derived pseudo-XRR is compared with the XRR measured by specular reflectometry from two simple vapor–liquid interfaces at different surface tension, and from a hexadecyltrimethylammonium bromide monolayer on a water surface. For the simple liquids, excellent agreement (beyond 11 orders of magnitude in signal) is found between the two methods, supporting the approach of using GIXOS-measured diffuse scattering to derive reflectivities. Pseudo-XRR obtained at different horizontal offset angles with respect to the plane of incidence yields indistinguishable results, and this supports the robustness of the GIXOS-XRR approach. The pseudo-XRR method can be extended to soft thin films on a liquid surface, and criteria are established for the applicability of the approach.

Enhancing mid-infrared surface phonon polariton modes: optimization of structural parameters in Nb-doped SrTiO3 with hole array structures for advanced infrared sensors

This study utilized the finite difference time domain method to investigate the mid infrared surface phonon polaritons and localized surface phonon resonances in undoped and niobium (Nb)-doped SrTiO3 (STO) with planar and holes array structures. Research has shown that Nb-doped STO operates in the Reststrahlen band of 8.06–18.48 µm, providing a wider spectral response than undoped STO (12.58–18.26 µm) and effectively covering the atmospheric window of long wave infrared. This indicates that the increase in virtual permittivity has the least impact on spectral broadening, indicating that the new infrared sensor technology has broad prospects. The optimization of structural parameters, including the period, filling factor, and depth of STO holes array, as well as the response to changes in incident light angle, is crucial for guiding the design of high-performance optoelectronic devices. In addition, this study explored the excitation of four resonant modes within a holes array and analyzed their relationship with array parameters to enhance the design of optoelectronic applications.

Bandpass frequency selective surfaces with fast roll-off characteristics

We propose a bandpass frequency selective surface (FSS) with fast cut-off characteristics and low insertion loss. It consists of a compact high-frequency hybrid compression board with five metal layers, two Rogers RO4003C layers, and two F4B layers. The hierarchical fitting of equivalent circuits is utilized to analyze the FSS, which maintains angular stability for dual-polarized electromagnetic waves at incidence angles of less than 20 degrees. Under normal incidence, transmission amplitudes in the K-band exceed −0.87 dB. Furthermore, the proposed FSS achieves a roll-off rate of 87.6 dB GHz−1, which can be applied in dual-frequency observing systems for millimeter astronomy.

Goos–Hänchen shift for coupled vibrational modes in a semiconductor structure

We present a theoretical investigation of the Goös–Hanchen shift (GHS) experienced by acoustic and optical vibrational modes reflected and transmitted from the surfaces of a semiconductor thin film sandwiched between two semi-infinite media. Our study focuses on the impact of the incident angle on the GHS, considering the coupling between longitudinal and transverse modes. For acoustic vibrations, our findings reveal that the GHS can reach magnitudes up to seven times larger than the thickness of the thin film and up to 20 times larger than the incident wavelength. Besides, it is shown that this significant amplification of the GHS highlights the strong influence of the incident angle and the frequency of the modes involved. In the case of optical vibrations, we observe even more pronounced GHS values, exceeding 30 times the incident wavelength. This demonstrates the potential of GHS in acoustical systems, which opens up possibilities for applications in the design of acoustic devices.

OSLD nanoDot characterization for carbon radiotherapy dosimetry

Objective. This study characterized optically-stimulated luminescent dosimeter (OSLD) nanoDots for use in a therapeutic carbon beam using the Imaging and Radiation Oncology Core (IROC) framework for remote output verification. Approach. The absorbed dose correction factors for OSLD (fading, linearity, beam quality, angularity, and depletion), as defined by AAPM TG 191, were characterized for carbon beams. For the various correction factors, the effect of linear energy transfer (LET) was examined by characterizing in both a low and high LET setting. Main results. Fading was not statistically different between reference photons and carbon, nor between low and high LET beams; thus, the standard IROC-defined exponential function could be used to characterize fading. Dose linearity was characterized with a linear fit; while low and high LET carbon linearity was different, these differences were small and could be rolled into the uncertainty budget if using a single linearity correction. A linear fit between beam quality and dose-averaged LET was determined. The OSLD response at various angles of incidence was not statistically different, thus a correction factor need not be applied. There was a difference in depletion between low and high LET irradiations in a primary carbon beam, but this difference was small over the standard five readings. The largest uncertainty associated with the use of OSLDs in carbon was because of the k Q correction factor, with an uncertainty of 6.0%. The overall uncertainty budget was 6.3% for standard irradiation conditions. Significance. OSLD nanoDot response was characterized in a therapeutic carbon beam. The uncertainty was larger than for traditional photon applications. These findings enable the use of OSLDs for carbon absorbed dose measurements, but with less accuracy than conventional OSLD audit programs.

Site Response in the Walnut Creek–Concord Region of San Francisco Bay, California: Ground-Motion Amplification in a Fault-Bounded Basin

ABSTRACT Thirty-seven portable accelerometers were deployed in the eastern San Francisco Bay communities of Walnut Creek and Concord to study site response in a fault-bounded, urban, sedimentary basin. Local earthquakes were recorded for a period of two years from 2017 to 2019 resulting in 101 well-recorded events. Site response is estimated by two methods: the reference site spectral ratio method and a source-site spectral inversion method. The reference site spectral ratio method allows investigation of the variability of site amplification with source azimuth and frequency. The source-site spectral inversion method yields the best least-squares fit to site response for a database of ground-motion records. Both methods show substantial amplification in the Walnut Creek–Concord basin below 2 Hz indicating strong surface-wave development. Greater amplification is seen for sources aligned along the long axis of the basin. Inversion using close-in sources at short distances yields lower amplification at longer periods than the entire data set due to reduced surface-wave generation for steeper angles of incidence. Inversion of site response spectra for shallow shear-wave velocity using a global search algorithm yields VS30 values consistent with generalized mapping results based on geology and topography but with greater variability due to local site variations. 3D finite-element modeling shows greater amplification in the Walnut Creek–Concord basin with a basin-edge effect likely contributing to higher ground motions. Topography is also seen to lead to increased scattering and shadowing effects.