Moisture Absorption Research Articles

The Effect of Wet and Dry Cycles on the Strength and the Surface Characteristics of Coromandel Lacquer Coatings

Research on the degradation mechanism of coating materials is crucial for the preservation of cultural heritage. The purpose of this study was to evaluate the protective effect of Coromandel coatings on wooden substrates by analyzing their dimensions, weight, adhesion strength, hydrophobicity, and glossiness. The results indicate that after five cycles, the radial moisture expansion rate of the wood specimen is 0.332%, while that of the lacquer specimen is 0.079%, representing 23.8% of the radial moisture expansion rate of untreated wood specimens. This performance is superior to that of the ash and pigment specimens. Across different experimental conditions, the change in the mass of the Coromandel specimens aligns with the trend in their dimensional changes, indicating that moisture absorption and desorption are the primary reasons for dimensional changes. The influence of temperature on mass and dimensional stability is significant only in terms of dry shrinkage rate. After wet and dry cycles at 40 °C, the adhesion strength of the Coromandel specimens decreases the most, with the ash specimens decreasing by 7.2%, the lacquer specimens by 3.2%, and the pigment specimens by 4.5%. Following wet and dry cycles at three different temperatures, the contact angle of the lacquer layers changes by less than 5%, with their contact angle values exceeding 120°. These data indicate that among the Coromandel coatings, the lacquer layer provides the best protection for the wooden substrate, while the ash coating is the most fragile. The degradation rate of the Coromandel specimens increases with rising temperatures. These findings emphasize the critical roles of humidity and temperature in protecting wooden coatings and aim to provide theoretical insights and practical significance for the preservation of wooden artifacts and the assessment of coating performance.

Chitosan Coating with Rosemary Extract Increases Shelf Life and Reduces Water Losses from Beef.

This study aimed to evaluate the influence of films based on chitosan and rosemary extract on the physicochemical, microbiological, and oxidative characteristics of beef. Refrigerated steaks of Longissimus dorsi were distributed in a factorial arrangement (4 × 4) into four treatments consisting of four edible films (control; chitosan; chitosan + 4% rosemary extract; and chitosan + 8% rosemary extract) and four days of aging (0, 2, 4, and 8 days). Incorporating 4% or 8% rosemary extract into the chitosan film improved the characteristics of the films in terms of moisture absorption and elasticity. The edible coatings with chitosan and rosemary extract and the different days of aging increased the tenderness and decreased the lipid oxidation of beef. In addition, the chitosan films containing rosemary extract increased the water-holding capacity and decreased the cooking losses of beef. The films containing 4% and 8% rosemary extract decreased the development of mesophilic and psychrotrophic bacteria and Staphylococcus ssp. in beef. We recommend incorporating 4% rosemary extract into chitosan-based coatings to preserve the quality of refrigerated beef.

Effect of Liquid Ammonia on the Structure and Properties of Superfine Wool Fibers

Superfine wool fiber has a soft and luxurious texture, excellent moisture absorption and is warmer and more comfortable than ordinary wool. Liquid ammonia, which has exceptional permeability, exerts a certain modification effect on the surface scales of wool in the finishing and processing of wool fabric, thereby enhancing its wear performance. However, limited research has been conducted on the impact of liquid ammonia on valuable wool fibers such as superfine wool and cashmere. In this article, superfine wool tops were treated with continuous liquid ammonia finishing equipment and the effects of liquid ammonia on the microstructure and surface morphology of superfine wool fiber were investigated. In addition, the changes in length, fineness, anti-felting, and dyeing properties of superfine wool fiber after liquid ammonia treatment were examined. The results demonstrated that the interstitial integrity of intercellular substance of superfine wool was compromised following treatment with liquid ammonia, which had a greater tendency to infiltrate cortical cells and induce alterations in wool structure and performance. Furthermore, the surface scales of superfine wool were damaged after treatment with liquid ammonia, leading to improved anti-felting and dyeing properties.

Thermal Stability, Durability, and Service Life Estimation of Woven Flax-Carbon Hybrid Polyamide Biocomposites.

Woven flax-carbon hybrid polyamide biocomposites offer a blend of carbon fibers' mechanical strength and flax's environmental advantages, potentially developing material applications. This study investigated their thermal behavior, degradation kinetics, and durability to water uptake and relative humidity exposure and compared them with pure flax and carbon composites with the same matrix. The hybrid composite exhibited intermediate water/moisture absorption levels between pure flax and carbon composites, with 7.2% water absorption and 3.5% moisture absorption. It also displayed comparable thermal degradation resistance to the carbon composite, effectively maintaining its weight up to 300 °C. Further analysis revealed that the hybrid composite exhibited a decomposition energy of 268 kJ/mol, slightly lower than the carbon composite's value of 288.5 kJ/mol, indicating similar thermal stability. Isothermal lifetime estimation, employing the activation energy (Ed) and degree of conversion facilitated by the Model Free Kinetics method, indicated a 41% higher service life of the hybrid laminate at room temperature compared to the carbon laminate. These insights are crucial for understanding the industrial applications of these materials without compromising durability.

Optimisation of cationic dye dyeing process of Porel fabrics using response surface methodology

AbstractPolyethylene terephthalate (PET) fibre, widely utilised across diverse industries, suffers from inherent drawbacks such as inadequate moisture absorption, limited hydrophilicity, and susceptibility to static electricity. To address these limitations, Porel fibre has emerged as a novel modified polyester fibre that incorporates flexible aliphatic polyester into its macromolecular chain. This innovative design not only overcomes the deficiencies of PET fibre but also enables it to be dyed using cationic dyes or disperse dyes under atmospheric pressure conditions. However, the investigation of the dyeing process of cationic dyes on Porel textiles remains relatively scarce. In this work, response surface methodology (RSM) was used to optimise the dyeing process of Porel fabrics with C.I. Basic Blue 162. The effects of dyeing temperature, dyeing time, and dye concentration on exhaustion percentage and colour strength (K/S value) were investigated using the Central Composite Design (CCD) method. The optimal dyeing process condition was as follows: a dyeing temperature of 96°C, a dyeing time of 51 min, a dye concentration of 3.6% owf, a dye solution pH value of 4–5, and a liquor ratio of 1:20. Under the optimal dyeing process conditions, the Porel fabrics achieved an exhaustion percentage of 96.2% and a K/S value of 36.0. The aforementioned efforts endow Porel fibre with high‐quality dyeing capabilities and broaden the application prospects of polyester textiles.

Wood dimensional stability enhancement by multivalent metal-cation-induced lignocellulosic microfibrils crosslinking

Wood is a hygroscopic material that responds to the moisture changes of the surrounding environment through swelling and shrinkage, making it dimensionally unstable. Here, we introduce a facile metal-ion-modification (MIM) approach to enhance the dimensional stability of wood. The MIM process involved swelling the wood samples with aqueous metal ion solutions and drying. The high valent metal cations, such as Fe3+, Al3+, and Zr4+, interacted with the hydrophilic groups (e.g., OH, COOH) present in the wood fibers, limiting their access to water and moisture, thereby enhancing the wood's hydrophobicity and dimensional stability. Evaluation of three wood species, southern yellow pine, poplar, and red oak, revealed water contact angles of 120–130° after MIM, indicative of enhanced surface hydrophobicity. Fe3+ treatment decreased southern yellow pine's swelling ratio from 6 % to 4 %. Fe3+-treated wood exhibited tangential anti-swelling efficiencies ranging from 39.83 % to 57.14 % and radial anti-swelling efficiencies from 34.74 % to 48.33 %, varying across wood species. The enhancement of wood dimensional stability can be attributed to the formation of irreversible coordination bonds between metal cations and lignocellulosic microfibrils in the wood cell wall. These bonds prevent the microfibrils from slipping in response to moisture absorption and desorption.

PEDOT:PSS based reprocessingly multifunctional dispersions and their optoelectronic films with excellent self-healing capability

Poly(3,4-ethylenedioxythiophene):polystyrene sulfonate (PEDOT:PSS) has become a hot and excellent candidate material for organic electronics. However, its film applications are limited due to its high accidental scratching or damage brittleness, easy moisture absorption and poor mechanical properties, etc. Herein, a thermo-driven healable waterborne polyurethane (WPU-DA) was introduced into PEDOT:PSS aqueous dispersion by simple mechanical mixing. The film prepared by the uniform mixture with cracks less than 10 μm achieved multiple structural morphology healing under treating at 130 °C for 10 min and then 65 °C for 1 h, and this process had little effect on its original electrical properties. Moreover, the film has good resistance to various solvents, especially water even after 14 days of immersion. The film also has excellent flexibility and electrochromic capability which can maintain stable electrical path even after multiple bending-stretching operations. In addition, the film can realize the synergistic healing of structural morphology and electrochromic properties, and a freeze-drying and redispersion process can reproduce above characteristics, supporting the long-term storage and in-site fabrication of polymer dispersions.

Effect of internal moisture content (IMC) on the CO2 sequestration efficiency of hollow natural fiber (HNF)-reinforced reactive magnesia cement (RMC) composites

The incorporation of minor hollow natural fibers (HNF) can significantly accelerate the CO2 diffusion in reactive magnesia cement (RMC). The CO2 diffusivity in HNF is highly related to its internal moisture content (IMC), which subsequently affects the carbonation process of HNF-RMC, but this is outside the scope of the existing studies. Therefore, this work investigates the effect of IMC on carbonation, strength, and microstructure of HNF-RMC composites. HNF-RMC mortar specimens are dried to different levels of nominal IMC (0–100%), and cured under high CO2 concentration for carbonation. Following the curing, the matrix composition was characterized with varying techniques (QXRD, TGA, FTIR, and acid digestion) for quantifying the CO2 sequestration; the compressive strength at different depths was determined with uniaxial compressive test; the microstructure was examined with SEM/ESEM. The results show that the carbonation depth is increased by three to four times by reducing the IMC to 0%. The effects of varying IMC on local carbonation and strength are distinct in the shallow (0–20 mm) and middle/deep region (20–100 mm). In the shallow region, inadequate CO2 dissolution is the limiting factor, these performances decreased with the increasing desiccation. In the deeper regions, moisture absorption by HNF decreased the CO2 diffusivity, hence the CO2 availability is the limiting factor, and these performances increased with the desiccation. These observations suggest that the understanding that carbonation maximizes at a medium moisture level is not valid in HNF-RMC–controlling the moisture can be important for improving the CO2 sequestration and consequent mechanical strength.

The Influence of Moisture Absorption and Desorption by the ABS Filament on the Properties of Additively Manufactured Parts Using the Fused Deposition Modeling Method.

This paper presents the results of research on the influence of the moisture content in a filament made of ABS polymer on the properties of products manufactured using FDM (fused deposition modeling). Tests were carried out on a standard printer, using the parameters recommended by the manufacturer and the literature on the subject. A special climatic chamber was used to condition the material. A negative impact of ABS filament moisture on the strength and dimensional accuracy of printed products and on the structure of their surface is demonstrated. When the range of the filament moisture is between 0.17% and 0.75%, the strength decreases by 25% and the sample thickness increases by 10%. It is also shown that this effect does not depend on the history of the polymer reaching a given moisture level, i.e., by absorbing moisture in the absorption process or releasing moisture in the desorption process.

Effects of moisture absorption analysis of kevlar/carbon/glass/polyurethane epoxy hybrid sandwich composites with nano silicon particles

ABSTRACT Hybrid sandwich polymer composites are widely used in aviation applications due to their attractive properties, such as their excellent strength capability, high modulus values, excellent stiffness properties, and greater wear resistance. This study aims to analyse the mechanical properties of degraded hybrid sandwich specimens exposed to moisture and investigate the moisture behaviour of the degraded sandwich panels. These panels are reinforced with woven fabrics made of kevlar, carbon, and glass fibres. The hand layup technique was employed to create the structures. The hybrid sandwich composite samples are submerged in normal seawater at ambient temperature for varied duration’s to measure the fibres’ water absorption characteristics. The study investigated the mechanical characteristics of an ageing moisture hybrid sample during tensile, flexural, and compressive tests. Novel stacking sequence arrangements (01 K/01 C/01 G/PUR/01 G/01 C/01 K) were used to enhance the stiffness, load-carrying capacity, yield strength, and other mechanical characteristics of the sandwich structures. The degraded sandwich panels demonstrated that water absorption significantly influences the tensile, flexural, and compressive properties of degraded sandwich structures compared with the results of regular sandwich panels. The tensile (31.67%, 40.40%, and 47.089%), flexural (63.13%, 66.05%, and 70.14%), compressive (33.14%, 39.37%, and 38.40%), and water absorption (3.75%, 3.97%, and 4.71%) test results were analysed.

Dimensionally stable and durable wood by lignin impregnation

Cracking, warping, and decaying stemming from wood's poor dimensional stability and durability are the most annoying issues of natural wood. There is an urgent need to address these issues, of which, sustainable and green chemical treatments are favorably welcomed. Herein, we developed a facile method through the incorporation of environmentally friendly biopolymer lignin into wood cells for wood dimensional stability and durability enhancement. Enzymatic hydrolysis lignin (EHL) was dissolved into various solvents followed by impregnation and drying to incorporate lignin into wood cells. Impregnation treatment was developed to incorporate into wood to improve its dimensional stability, durability, and micromechanics. The anti-swelling efficiency reached up to 99.4 %, the moisture absorption decreased down to 0.55 %, the mass loss after brown rot decay decreased to 7.22 %, and the cell wall elasticity as well as hardness increased 8.7 % and 10.3 %, respectively. Analyses acquired from scanning electron microscopy, fluorescent microscopy, and Raman imaging revealed that the EHL was successfully colonized in cell lumen as well as in cell walls, thus improved wood dimensional stability and durability. Moreover, Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy confirmed EHL interaction with the cell wall components, thus the wood mechanical property was not impaired significantly, whereas nanoindentation data indicated even slight mechanical enhancement on the cell walls. This facile approach can improve the wood properties in multiple aspects and remarkably enhance the outdoor performance of modified wood products. In addition, using lignin as a natural modifying agent to improve wood performance will have a great positive impact on the environment.

Composite porous 3D foam for solar-driven atmospheric water harvesting in low humidity natural environment

Solar-driven atmospheric water harvesting (SAWH) has been recognized as a promising strategy to alleviate the freshwater crisis. Herein, we developed an efficient porous polymeric foam, LiCl@CCP-PPy, which has low preparation cost, strong adaptability and portability, and is very suitable for use as a wicking material in SAWH systems. LiCl@CCP-PPy contains abundant –NH2 and –OH groups. These hydrophilic groups and excellent pore structure (porosity is 80.22 %) make it have a good moisture absorption effect even in low humidity environment. The moisture absorption capacity can reach 2.86 g/g at 35 % RH and 25 °C, and 4.48 g/g at 25 °C and 90 % RH. The saturated water absorption effect was 27.48 g/g. LiCl@CCP-PPy can be scaled up for production. In addition, LiCl@CCP-PPy has a high light absorption rate of more than 90 %, and the strong photothermal conversion ability of Polypyrene (PPy) enables the material to warm up rapidly under natural light, thereby accelerating the desorption process (96 % desorption rate at 1 kW/m2 for 3 h). Based on the above properties, LiCl@CCP-PPy was applied to the Tengger desert in northwest China. The final water production efficiency was 0.64 L/m2/d, and the collected water quality met the international drinking water standard.

Study on Preparation and Humidity-Control Capabilities of Vermiculite/Poly(sodium Acrylate-acrylamide) Humidity Controlling Composite.

This paper focuses on the preparation and evaluation of a novel humidity-control material, vermiculite/(sodium polyacrylate(AA)-acrylamide(AM)), using inverse suspension polymerization. Acrylic acid and acrylamide were introduced into the interlayer of modified vermiculite during the polymerization process, leading to the formation of a strong association with the modified vermiculite. The addition of vermiculite increased the specific surface area and pore volume of the composites. To investigate the moisture absorption and desorption properties of the composites, an orthogonal experiment and single-factor experiment were conducted to analyze the impacts of vermiculite content, neutralization degree, and the mass ratio of AA to AM. According to the control experiment, the addition of vermiculite was found to enhance the pore structure and surface morphology of the composite material, surpassing both vermiculite and PAA-AM copolymer in terms of humidity control capacity and rate. The optimal preparation conditions were identified as follows: vermiculite mass fraction of 4 wt%, a neutralization degree of 90%, and mAA:mAM = 4:1. The moisture absorption rate and moisture release rate of the composite material prepared under these conditions are 1.285 g/g and 1.172 g/g. The humidity control process of the composite material is governed by pseudo second-order kinetics, which encompasses the complete adsorption process. These results indicate that the vermiculite/PAA-AM composite humidity control material has excellent humidity control performance and is a simple and efficient humidity control method.

Isolation, purification, and biological activities of polysaccharides from Amorpha fruticosa flowers

The extraction, isolation, structural characterisation and biological activities of polysaccharides from Amorpha fruticosa flowers were investigated. First, the crude polysaccharide AFP was extracted, and two major purified polysaccharide fractions AFP-2 and AFP-3 were isolated. The molecular weight and monosaccharide compositions of AFP-2 and AFP-3 were determined. Then the antioxidant activities of AFP, AFP-2 and AFP-3 were assessed by DPPH radical, β-Carotene bleaching and hydroxyl radical assays. All three tested polysaccharides showed good antioxidant activity while AFP was the strongest one. The study also showed that AFP, AFP-2 and AFP-3 have good tyrosinase inhibition, moisture absorption and retention activities. The results will provide a helpful reference for the application of polysaccharide from Amorpha fruticosa flowers as a natural cosmetic ingredient.

Dual-Responsive MXene-Functionalized Wool Yarn Artificial Muscles.

Fiber-based artificial muscles are promising for smart textiles capable of sensing, interacting, and adapting to environmental stimuli. However, the application of current artificial muscle-based textiles in wearable and engineering fields has largely remained a constraint due to the limited deformation, restrictive stimulation, and uncomfortable. Here, dual-responsive yarn muscles with high contractile actuation force are fabricated by incorporating a very small fraction (<1wt.%) of Ti3C2Tx MXene/cellulose nanofibers (CNF) composites into self-plied and twisted wool yarns. They can lift and lower a load exceeding 3400 times their own weight when stimulated by moisture and photothermal. Furthermore, the yarn muscles are coiled homochirally or heterochirally to produce spring-like muscles, which generated over 550% elongation or 83% contraction under the photothermal stimulation. The actuation mechanism, involving photothermal/moisture-mechanical energy conversion, is clarified by a combination of experiments and finite element simulations. Specifically, MXene/CNF composites serve as both photothermal and hygroscopic agents to accelerate water evaporation under near-infrared (NIR) light and moisture absorption from ambient air. Due to their low-cost facile fabrication, large scalable dimensions, and robust strength coupled with dual responsiveness, these soft actuators are attractive for intelligent textiles and devices such as self-adaptive textiles, soft robotics, and wearable information encryption.

Oleic acid decorated kraft lignin as a hydrophobic and functional filler of cellulose acetate films

The packaging industry has primarily been dominated by single-use, petrochemical-sourced plastic materials despite their short-term use. Their leakage into the ecosystem after their use poses substantial environmental concerns. As a result, compostable and renewable packaging material alternatives are garnering significant attention. Cellulose acetate is a derivative of cellulose that exhibits excellent tensile properties, transparency, melt processability, and intermediate compostability. However, its application in the food packaging industry is limited due to its hygroscopic behavior and lack of dimensional stability. This study investigated using lignin (pristine and esterified) as a functional additive of cellulose acetate. The effect of varying concentrations of pristine kraft and oleic acid functionalized lignin in the cellulose acetate matrix and its effect on the resulting film's mechanical, morphological, viscoelastic, and water barrier properties were explored. Comprehensive characterization of the thermomechanical processed lignin-cellulose acetate sheets revealed reduced moisture absorption, improved UV and moisture barrier, and enhanced tensile properties with melt processability. Overall, the studied films could have appealing properties for food and other packaging applications, thus, serving as eco-friendly and sustainable alternatives to conventional petroleum-derived packing materials.

Alginate-coated functional wrapping paper incorporated with sulfur quantum dots and grapefruit seed extract for preservation of potato hash browns

This study explores the impact of alginate-based functional coatings incorporating sulfur quantum dots (SQDs) and grapefruit seed extract (GFSE) on the antioxidant and antibacterial properties of kraft paper for food packaging. Applying these coatings effectively fills the porous interfibrillar spaces of the paper, significantly improving oil resistance and mechanical properties. However, the water vapor permeability and moisture absorption rate decreased slightly due to the hydrophilic nature of constituents. In particular, the addition of 5 wt% SQDs to the paper coating formulation resulted in remarkable antioxidant activity, with approximately 100% reduction in ABTS and 60% reduction in DPPH free radicals. The addition of SQDs significantly reduced the bacterial cell viability of E. coli and L. monocytogenes by ∼2 log CFU/mL and ∼4.5 log CFU/mL, respectively. Co-addition of SQDs and GFSE significantly improved antimicrobial activity with ∼3 log CFU/mL reduction of E. coli and complete (100%) eradication of L. monocytogenes even at lower concentrations (2.5 wt% each). The lipid oxidation in the hash brown potato patties wrapped in functional coated paper was reduced by nearly 50% compared to uncoated paper. This effect persisted even after an extended storage period of 15 days, demonstrating the superior ability of the coated paper to improve the shelf life of processed, ready-to-eat foods.

Green moisture-electric generator based on supramolecular hydrogel with tens of milliamp electricity toward practical applications.

Moisture-electric generators (MEGs) has emerged as promising green technology to achieve carbon neutrality in next-generation energy suppliers, especially combined with ecofriendly materials. Hitherto, challenges remain for MEGs as direct power source in practical applications due to low and intermittent electric output. Here we design a green MEG with high direct-current electricity by introducing polyvinyl alcohol-sodium alginate-based supramolecular hydrogel as active material. A single unit can generate an improved power density of ca. 0.11 mW cm-2, a milliamp-scale short-circuit current density of ca. 1.31 mA cm-2 and an open-circuit voltage of ca. 1.30 V. Such excellent electricity is mainly attributed to enhanced moisture absorption and remained water gradient to initiate ample ions transport within hydrogel by theoretical calculation and experiments. Notably, an enlarged current of ca. 65 mA is achieved by a parallel-integrated MEG bank. The scalable MEGs can directly power many commercial electronics in real-life scenarios, such as charging smart watch, illuminating a household bulb, driving a digital clock for one month. This work provides new insight into constructing green, high-performance and scalable energy source for Internet-of-Things and wearable applications.

Evaluation of Chemical and Biological Properties of Biodegradable Composites Based on Poly(3-hydroxybutyrate) and Chitosan.

In this study, composite films and scaffolds of polyester poly(3-hydroxybutyrate) and polysaccharide chitosan obtained via a simple and reproducible blending method using acetic acid as a solvent were considered. The degradation process of the films was studied gravimetrically in a model biological medium in the presence of enzymes in vitro for 180 days. The kinetics of weight reduction depended on the amount of chitosan in the composition. The biocompatibility of the films was evaluated using the Alamar blue test and fluorescence microscopy. The materials were non-cytotoxic, and the addition of poly(3-hydroxybutyrate) to chitosan improved its matrix properties on mesenchymal stem cells. Then, the 3D composites were prepared by freeze-drying. Their structure (using SEM), rheological behavior, moisture absorption, and porosity were investigated. The addition of different amounts of chitosan allowed us to vary the chemical and biological properties of poly(3-hydroxybutyrate) materials and their degradation rate, which is extremely important in the development of biomedical poly(3-hydroxybutyrate) materials, especially implantable ones.

Moisture absorption and desorption characteristics and prediction model analysis of building thermal insulation materials

Understanding the isothermal moisture absorption and desorption characteristics of building thermal insulation materials and how they affect thermal conductivity, is curial for accurate building thermal design and energy-saving calculation. In this paper, five types of building thermal insulation materials are selected for investigation. First, the variation trend of the equilibrium mass moisture content of materials in different moisture absorption and desorption stages is studied employing the saturated salt solution method and the constant temperature and humidity box method, and the effect of temperature on the moisture absorption and desorption processes is evaluated. Additionally, the applicable model of the material in the moisture absorption and desorption process is obtained through a fitting analysis of the experimental data. Finally, the influence of the material’s moisture absorption and desorption characteristics on the thermal conductivity is analyzed using the transient thermal conductivity test method. The results highlight that there is a need to consider the moisture absorption and desorption processes to accurately determine the wet material thermal conductivity, and the hysteresis effect of the material in the moisture absorption and desorption processes is directly related to its microstructure and the relative humidity at the initial moisture desorption. At a temperature of 25 oC, the autoclaved aerated concrete exhibits its highest hysteresis rate of thermal conductivity during the moisture desorption process of third stage, reaching 13.2%.