Temperature Absorption Research Articles

Improved performance of kesterite Cu2ZnSn(S,Se)4 thin film solar cells by Ag/Ge co-doping

Cation doping is an important approach to improve the performance of kesterite Cu2ZnSn(S,Se)4 (CZTSSe) thin film solar cells. Since different cation dopant has different effects on the defects and crystallization of CZTSSe absorber, it is expected to achieve better device performance via the synergistic effects of double cation co-doping compared with the single cation doping. Herein, we investigated the effects of Ag/Ge co-doping on CZTSSe solar cells by doping Ge in an already optimized Ag-alloyed CZTSSe (ACZTSSe). It is found that incorporating a small amount of Ge can further improve the crystallinity and minority carrier lifetime of ACZTSSe. The low-temperature photoluminescence results reveal that the Ge doping primarily suppressed the SnZn defects in ACZTSSe, thereby further boosting the device performance. However, higher Ge doping concentration can lead to a discontinuous surface morphology, which is believed to be related with the relatively low melting temperature and double-layered structure of ACZTSSe absorber. The deteriorated surface morphology results in photocurrent loss in the near-infrared region and decreased fill factor. As the Ge doping ratio increases, there is a balance between the defects and morphology. A champion power conversion efficiency (PCE), 11.4%, was achieved for the Ag/Ge co-doped CZTSSe solar cells at Ge substitution rate of 3%. Compared with the single Ag doping, the average PCE was further promoted by 0.5% due to Ag/Ge co-doping.

Modeling and Parametric Analysis of a Large-Scale Solar-Based Absorption Cooling System

This study investigates the thermodynamic performance of a solar-powered absorption cooling system. The system uses a lithium bromide-water (LiBr-H2O) absorption refrigeration system (ARS) integrated with evacuated solar collectors (ETSC) and thermal energy storage (TES) to provide a 3 kTR cooling capacity for a university campus. The paper examines the performance of the integrated system under different design and operating conditions as well as the performance of each subsystem, i.e., ETSC, TES, and ARS. Furthermore, a parametric energy and exergy analysis is applied, where different parameters are studied, such as the temperatures of the generator, the condenser, the evaporator, and the absorber. In addition, the system performance is examined with the variation in environmental conditions. The coefficient of performance (COP), exergetic efficiency, exergy destruction, and fuel depletion ratio (FDR) are used to evaluate the system’s performance. The ETSC and the TES are studied under the variation in solar radiation through the day in two seasons: summer and winter. The results revealed that the increase in generator temperature positively impacts the COP of the ARS while lowering the condenser and absorber temperature gives the same positive effect. Furthermore, the main reason for the exergy destruction is found to be the solar collector, which is responsible for destroying 89% of the input solar exergy. Additionally, 4.7% of the inlet exergy is destroyed in the generator, which makes 4.5% of the total exergy loss. The TES destroyed 4.8% of the total solar exergy input. The energy analysis shows that the ARS achieves an energetic COP of about 0.77, while the exergy analysis revealed that the exergetic COP is 0.21.

Modeling and optimization of numerical studies on CuSbS2 thin film solar cell with ∼ 15% efficiency

In this paper, the Silvaco TCAD simulation tool is utilized for modeling of ternary chalcostibite copper antimony sulfide (CuSbS2) thin film solar cells (TFSCs). The earth-abundant CuSbS2 is a promising material as a solar absorber and hole transport layer due to its high optical absorption coefficient, and low cost. CuSbS2 based solar cell can be fabricated in vacuum-free environment. Mostly CdS is used as electron transport layer (ETL) in CuSbS2 based solar cell but the efficiency is low due to creation of Schottky barrier at the back-contact and substantial carrier recombination at the CuSbS2/CdS interface. Hence, a (ITO/n-TiO2/p-CuSbS2/Au) np heterojunction-based solar cell has been developed. The observed maximum power conversion efficiency (PCE) of 15.26% (open circuit voltage (Voc) = 823 mV, short circuit current (Jsc) = 28.48 mA/cm2, fill factor (FF) = 65.1%) is achieved by optimizing the absorber thickness (400 nm) of the solar cell. Different parameters like effect of absorber thickness, back contact, bandgap, carrier concentration, temperature, and defect density are optimized to find the best possible efficiency of the solar cell. The device also exhibits good performance stability at high temperatures. Based on results, a (ITO/n-TiO2/p-CuSbS2/Au) np heterojunction-based fabricated solar cell device is possible in future.

Waste-derived thermal storage solutions for sustainable solar desalination using discarded engine oil and paraffin wax: A techno-environmental feasibility evaluation

The valorization and repurposing of waste materials for sustainable outcomes and environmental mitigation are gaining prominence. This investigation explores the feasibility of repurposing discarded automotive engine oil as a viable means of energy storage in solar thermal desalination applications. A novel approach combining discarded engine oil with Paraffin wax in equal parts by volume is proposed as a composite energy storage (CES) to enhance nocturnal production and efficiency. The experimental findings show that the composite energy storage system has 26.54 % higher thermal conductivity and 44.66 % greater specific heat energy storage capacity compared to pure paraffin wax. Comparing the Desalination System with Engine Oil-based Energy Storage (DSEES) to a Traditional Solar Desalination System (TSDS) without energy storage, considering water and absorber temperatures and distillate production, reveals compelling advantages. DSEES exhibits remarkable temperature increases of 14 % in the basin and 11 % in water, alongside a significant 52.72 % rise in distillate production rates, yielding 3.36 and 3.16 l/sq.mt compared to TSDS's 2.2 and 2.1 l/sq.mt over two testing days. Cost analysis indicates DSEES's 33.7 % lower cost per liter and 33.8 % shorter payback period relative to TSDS. Furthermore, environmental assessment highlights DSEES's 60.8 % greater net carbon credit, indicating reduced ecological impact.

Numerical investigation of increasing the efficiency of thermal photovoltaic system by changing the level of heat transfer distribution

In photovoltaic systems, only a small fraction of solar radiation effectively reaches the module's surface and is converted into electrical energy. The unused solar radiation results in elevated cell temperature and reduced electrical efficiency. In the photovoltaic-thermal system, the circulation of fluids such as water or air around the panels allows for the utilization of otherwise wasted thermal energy, leading to increased electrical efficiency and overall system efficiency. The objective of this article is to examine the thermal efficiency of copper and aluminum oxides in photovoltaic systems when combined with nanofluid. The aim is to identify any changes in efficiency that may arise from this combination. This article presents a novel approach by employing a combination of aluminum oxide and copper nanofluids, along with a water mixture, to investigate the influence of key factors on the electrical, thermal, and overall efficiency of photovoltaic systems. These factors encompass incoming radiation levels on the panel surface, fluid inlet temperature in mountainous regions, and absorber temperature. The study aims to analyze and compare the thermal efficiency of copper and aluminum oxide in this particular context. In the present study, the finite volume method is used to solve the equations. According to the research findings, raising the initial temperature of the incoming fluid results in a proportional increase in the outlet temperature. However, it is important to note that the thermal efficiency remains constant regardless of changes in the initial fluid temperature. Furthermore, copper oxide exhibits superior thermal efficiency compared to aluminum oxide, and the use of nanofluids enhances the thermal efficiency of photovoltaic systems.

Investigation of Solar Powered Single Effect Absorption System

Cooling processes like refrigeration and air conditioning are known for their high energy consumption. Since most Indian states experience abundant sunshine year-round, solar refrigeration is a suitable technology for the country. Solar-powered absorption refrigeration systems offer a viable alternative to traditional refrigeration, providing not only cooling and ice-making capabilities but also energy savings and environmental benefits. However, further research is necessary to enable widespread industrial adoption and the replacement of conventional refrigeration systems with solar powered absorption system. Using solar energy for an air-conditioning system is typically more cost-effective, when it can fulfil both heating and cooling needs. This research focuses on the thermodynamic modelling of a system, specifically the effect of various temperature on COP. Thermodynamic modelling was done with the help of first law of thermodynamics. Using engineering equation solver software, study simulated the cycle and equations were developed for energy and mass flow for each component. Further, before proceeding to analysis some assumptions were also made. We then analysed how the Coefficient of Performance (COP) changed when varying the temperatures across each component. Our findings show that COP increases with increase in condenser, evaporator, and absorber temperatures, but it is declined with decrease in generator temperature.

Thermo-hydraulic analysis of direct steam generation in a 500 m long row of parabolic trough solar collector using Eulerian two-fluid modeling approach

Direct steam generation (DSG) in the parabolic trough solar collectors is a potential alternative for economic and performance improvement of the solar thermal system. This process comprises the preheating, evaporation, and superheating of water/steam in the solar collectors. The modeling and simulation of the evaporation section are challenging because of the complex physics associated with the boiling phase change process. This work describes the Eulerian two-fluid modeling of the once-through mode of the DSG process in solar collectors. The interfacial interactions between phases have been modeled using the appropriate empirical correlations. The experimental data from the Spanish DISS test facility is used to validate the numerical model. Further, the 3-D thermal–hydraulic investigation of DSG in a 500 m long solar collectors' row has been performed for operating pressures of 60 bar and 100 bar; inlet mass flow rates of 0.4 kg/s and 0.6 kg/s; DNI of 750 W/m2 for the solar time at 12:00 h and 13:00 h. It has been observed that the maximum absorber temperature is reduced by 27 % at 60 bar and 20 % at 100 bar operating pressure when the inlet mass flow rate increases from 0.4 kg/s to 0.6 kg/s. Similarly, the maximum circumferential temperature difference reduces by 12 % and 14 %, respectively. Moreover, the fluid temperature, steam quality, absorber temperature distributions, fluid velocity, and pressure loss under the subjected boundary conditions have been summarized.

Design and Assessment of a solar collector system for low-cost, pollution-free cooking and grilling applications

Recently, using solar energy for several purposes has become very important to preserve the environment, reduce pollution, and reduce consumption. Examples of these applications are cooking, barbecuing, desalination, and generating electrical power. Solar oomph is extremely important in providing the energy used in cooking. In the current work, a solar collector consisting of six flexible reflective panels was designed and assembled for solar cooking and grilling operations in the city of Jazan, southwestern Saudi Arabia. Pots of different sizes have been prepared for cooking operations, as well as a grid for grilling operations. They are installed at the center of the collection of reflected rays from the solar center, in addition to a movable stand and a manual system for directing the direction of the falling sunlight. The current solar energy system provides an estimated power of about 2,300 watts from 9 a.m. to 5 p.m. It took 16 minutes to cook 2700 grams of vegetables with the current system and less than two minutes to boil 2 liters of water. Grilling a whole chicken weighing 800 grams, cut in half, takes about ten minutes. Cooking was also done inside the kitchen using a solar energy source by transferring heat from the solar concentrator's absorber to a 35-diameter pipe filled with vegetable oil as a heat transfer fluid. The absorber temperature reached 321 degrees Celsius, while the internal cooking stove registered 129 degrees. The storage of collected heat and how it is transferred to indoor cooking processes were also studied.

Analysis and multi-objective evolutionary optimization of Solar-Biogas hybrid system operated cascade Kalina organic Rankine cycle for sustainable cooling and green hydrogen production

A novel cascade system of Kalina and Organic Rankine cycle for cooling and green hydrogen production was proposed. The cascade system is designed to utilizes the heat effectively with heat recovery components for sustainable cooling and green hydrogen. The proposed system consists of a solar-biogas hybrid heat source, Kalina and ORC power generation system, dual evaporator vapor compression cooling system and solid oxide electrolyser. The system's performance is evaluated based on the availability of low-temperature heat sources (90 to 150 °C) and medium-grade heat sources (190–280 °C). It is assessed for its capability to provide cooling only or in combination with hydrogen production, and their efficient utilization is compared from energetic, exergetic, environmental, and economic perspectives. To optimize this innovative system, a multi-objective evolutionary approach is employed, considering operating conditions as constraints and incorporating performance metrics for all criteria as objectives. Utilizing multi-objective decision-making techniques, diverse optimal points are pinpointed within the trade-off space, enabling real-time adaptive responses to changes in weather, energy demands, and biogas availability. The net present value analysis demonstrates that, assuming a hydrogen selling price of $6 per kilogram and cooling costs of $4 per KW the payback periods are calculated to be 2 years for the ORC-VCRS cycle and 3 years for the integrated Kalina topping with bottoming ORC cycle. The multi-objective optimization results indicate that the optimum operating conditions for the cascade system involve boiler, absorber, and condenser temperatures set at 196 °C, 110 °C, and 25 °C, respectively. Under these conditions, the system achieves an energy utilization ratio of 0.76, an exergy efficiency of 21.56 %, and a total cost of $58,677.

Assessment of the Possibility of Validating the Durability Testing Method for Large-Sized Vehicles Based on Changes in Shock Absorber Characteristics—Preliminary Tests

The use of road simulators in vehicle durability tests enables a significant reduction in time related to the implementation of a new product. However, there is still a need to improve the methods of these tests in order to obtain a full correlation between the time of the tests on the simulator with respect to the mileage of the vehicle in real road conditions. The aim of this work is a validation and improvement of the durability testing method for large-sized vehicles. Comparative tests of shock absorbers dismantled from semi-trailers with different mileage and shock absorbers dismantled from semi-trailers after durability tests conducted at the MTS test bench are presented. The relationship between the maximum damping force and the displacement speed of the shock absorber piston was examined. Additionally, the influence of the shock absorber temperature on the damping force was analyzed. As a result of the tests, the dynamic characteristics of the shock absorbers were determined and the relationship between the maximum damping force and the mileage of the trailers was determined. It was found that the load on the trailers during their operation has a significant impact on the change in the characteristics of the shock absorbers. What is new in this publication is the validation of the methodology for conducting durability tests previously proposed by the authors based on the selected component, which is the shock absorber. The authors have not yet encountered in the literature any attempt to validate the methodology for conducting durability tests for large-sized vehicles.

Improvement in the efficiency of solar cells based on the ZnSnN2/Si structure

This study aims to investigate the different optical properties of the ZnSnN2 absorber layer such as absorption, reflection and transmission coefficients. The effects of the ZnSnN2 absorber layer thickness, temperature,and defect density on electrical parameters such as short circuit current density, open circuit voltage, fill factor and efficiency have also been studied in detail. These factors play an important role in the performance of the ZnO/CdS/ZnSnN2/Si/Mo structure. The highest efficiency of about 23.32 % is achieved without defects in the ZnSnN2 absorber layer, under the 1-sun AM1.5 solar spectrum, by applying the flat band condition and considering the strain values of 0.37 % (ZnSnN2/Cds) and 7.17 % (ZnSnN2/Si). In addition to high efficiency, the ZnSnN2 has a high absorption coefficient. This device will play a crucial role in optoelectronic applications. This structure is a promising candidate for low cost and high efficiency photovoltaic technology.

EXPLORING EFFICIENCY AND DESIGN OPTIMIZATION OF FLEXIBLE PEROVSKITE SOLAR CELLS USING SCAPS-1D SIMULATION

This research focuses on using SCAPS-1D software to design and simulate efficient flexible perovskite solar cells. The study aims to optimize design parameters, gain a deeper understanding of the underlying physics, and obtain valuable insights into electrical characteristics. The device architecture includes key components like PET/ITO substrate, TiO2 ETL, CH3NH3SnI3 absorber, CuSCN HTL, and Au electrode. By optimizing the absorber thickness (600 nm) and temperature (300 K), the performance and efficiency of the cell were improved. Investigation of different doping concentrations at 300 K for a fixed thickness revealed an efficiency of 26.98% at 600 nm. The highest efficiency of 31.44% was achieved with a doping concentration of 1E+21. This research showcases the potential of flexible perovskite solar cells for lightweight and versatile applications, emphasizing their significance in the field.

Photovoltaic energy conversion in multiferroic perovskite absorber-based devices via experiment and theoretical calculations

Initially, La and Ti-doped BiFeO3 (BLFTO) was prepared through the solid-state method, and the formation of perovskite structure was confirmed through powder X-ray diffraction (XRD) analysis. SEM-EDX analysis confirms the merging of grains for the increasing concentration of Ti ion doping and the presence of all elements in the samples. The bandgap tuning in BLFTO (2.05 eV–2.11 eV) was analyzed through UV–vis spectroscopy and confirming the change in bandgap for Ti-doped BLFO samples. The observed energy bandgap range of the doped BFO absorber suggested its potential applications in solar cell devices. Therefore, we have designed lead-free FTO/TiO2/absorber/Spiro-OMeTAD/Au heterostructure device and achieved a power conversion efficiency (PCE) of ∼5.61% with an open-circuit voltage (VOC) of ∼0.91 V, fill factor (FF) of 55.55%, and current density (JSC) of 10.87 mA/cm2 for lead-free doped Bi0.80La0.20Fe1−xTixO3 (x = 0.0) based perovskite solar cells with proper optimization of thickness of absorber and operating temperature.

Experimental and numerical simulation studies of CuO thin films based solar cells

This study presents an experimental investigation into the solar performance of copper oxide (CuO) thin films. These CuO films were fabricated using the spray pyrolysis technique, and their structural, morpholigical, optical, and electrical properties were examined in relation to the effect of layer thickness. Additionally, we employed SCAPS-1D software to perform numerical simulations of CuO-based solar cells. Moreover, the band gap energy was discovered to be between 1.14 eV, 1.53 eV and 1.61. Using the four-point probe, the electrical resistivity was computed and the high conductivity found corresponds to the sample generated with a film thickness of t = 292 nm, is 7.52 (×10−3 Ω.cm)−1. The CuO/TiO2/FTO solar cell configuration showed a potential efficiency of 13.38% when the absorber layer thickness is 292 nm and the band gap value is 1.53 eV. Furthermore, based on the band gap energy value of 1.53 eV the investigation has been deepened by expanding the range of absorber layer thickness and temperature to thoroughly examine their impact on solar cell performance. Moreover, the CuO/TiO2 solar cells curves of external quantum efficiency (EQE) for various CuO layer thicknesses were determined.

Improving luminescence characteristics of Ni2+ doped CsPbX3 (X = Br/I, I) quantum dots in borogermanate glass for wide color gamut display

For wide gamut backlight display application, main problems of CsPbX3 (X = Br/I, I) quantum dots (QDs) glasses as red emission materials are too long emission wavelengths, low luminescence intensity and worse uniformity. The full width at half maximum (FWHM) and decay time should also be considered. Here, Ni2+ doped CsPbX3 (X = Br/I, I) QDs in borogermanate glasses have been successfully fabricated by melt quenching and heat treatment. Transmittance, absorbance, photoluminescence (PL), PL excitation (PLE), PL decay and PL temperature characteristics are measured. By Ni2+ doping in the CsPbX3 (X = Br/I, I) QDs glasses (QDGs), PL intensity is significantly improved to higher level of 106–107 counts (enhanced by 1.6–1.7 times). The peak wavelength is adjusted to suitable range of 630–650 nm by double anion CsPb(Br/I)3 QDs. The uniformity is greatly improved by using suitable composition and concentration of CsPbX3 (X = Br/I, I) QDs. In addition, the FWHM of 32–46 nm is sufficiently narrow. The PL decay shows sufficiently short lifetime of less than 100 ns. The PL temperature dependence fitting shows large exciton binding energy 376–400 meV. For wide color gamut display application, we have used three primary colors with the standard blue, green and red lights in NTSC standard, and the red light has been replaced by using perovskite CsPbX3 (X = Br/I, I) QDGs. For the perovskite CsPbX3 (X = Br/I, I) QDGs emitted at 667 nm and 644 nm, the color gamut area has been increased by 11% and 9%, respectively. The results indicate that the red light QDG materials can be applied to wide color gamut display.

Modeling and performance study of CZTS solar cell with novel cupric oxide (CuO) as a bilayer absorber

A Kesterite material like CZTS provides the steering to the researcher with their tunable bandgap and high optical coefficient above 104 cm−1 for solar cells. These features make it a suitable material for a single junction solar cell increasing the acceptance as well. In this paper, comparative numerical simulations were performed on a regular base structure of CZTS absorber layer with a CdS buffer layer, a ZnO window layer, and a transparent n-ITO conducting layer with a proposed structure where CZTS absorber layer is replaced by a CZTS and CuO bi-layer using SCAPS-1D software to optimize the efficiency. In addition to that the thickness, defect densities and doping concentrations of the absorber layers and temperature were varied to observe the responses of open-circuit voltage (VOC), short-circuit current (JSC), fill factor (FF) and efficiency (η) of the solar cell. Among the three basic researchs on lost mechanism for kesterite materials, we have focused on improving the back contact interface recombination through an absorber bi-layer combination of CZTS and CuO resulting in increased VOC, Quantum efficiency and carrier generation efficiency approximately by 50 %, 8.94 %, and 34 % respectively, elevating the efficiency of the proposed structure to 19.92 %.

Development of Thermal Energy Storage Material From Blends of Jatropha Biodiesel and Paraffin Wax for Augmenting Freshwater Generation Capacity in a Solar Desalination System

Abstract Enhancing nocturnal productivity holds promise for boosting the effectiveness of solar desalination setups. Current research concentrates on an innovative strategy: the integration of paraffin wax and Jatropha biodiesel as a composite energy storage material (CESM) to amplify distilled water output during nighttime. The composite material, comprising Jatropha biodiesel and paraffin wax in a 1:1 ratio by weight, is meticulously examined for its impact on productivity, juxtaposed against a conventional solar still (CSS). Results reveal a substantial improvement in thermal conductivity with CESM, exhibiting a noteworthy 20.37%% surge compared to pure paraffin wax. Furthermore, a solar still with biodiesel and phase change material (SSBDPCM) is pitted against a CSS, with continuous monitoring of water and absorber temperatures alongside distillate production. The findings illustrate that SSBDPCM achieves a 16% upsurge in water temperature and a 10% elevation in absorber temperature compared to CSS. Impressively, SSBDPCM achieves a staggering 63% increase in distillate production, yielding 3.6 l/m2 and 3.4 l/m2, in sharp contrast to CSS, which only manages 2.2 l/m2 and 2.1 l/m2 over a two-day test period. Furthermore, a comprehensive cost analysis showcases the economic superiority of SSBDPCM over CSS. SSBDPCM demonstrates a compelling 29.2% reduction in cost per liter and a significant 25.9% decrease in the payback period in comparison to CSS. These compelling outcomes underscore the substantial potential of the SSBDPCM approach in delivering heightened efficiency and cost-effectiveness, paving the way for a promising advancement in solar stills.

Simulasi CFD Distribusi Temperatur pada Pengering Biji Kopi dengan Sistem Konveksi Paksa

Drying is a mass transfer and heat transfer process that is strongly influenced by temperature and air velocity. The importance of analyzing the temperature distribution and air velocity is expected to be used as a reference to optimize the drying process to be faster and better. This study aims to analyze the temperature distribution and air velocity that occurs in a coffee bean dryer with a forced convection system using CFD simulation. CFD simulations are carried out using ANSYS Fluent software. with steady conditions, and using a pressure-based solver method. The obtained temperature distribution occurs with an estimated absorber temperature difference with the drying chamber is 31% during the day.

Comparative Study of Different Perovskite Active Layers for Attaining Higher Efficiency Solar Cells: Numerical Simulation Approach

The simulated device structures of ITO/ZnO/Perovskite absorber layers (PAL)/Spiro-OMeTAD/Au with distinct absorbers were modeled and investigated using solar cell capacitance simulator (SCAPS-1D) simulating software (version 3.8). The primary objective is to enhance the thermal stability of the solar device. As the absorber thickness and temperature impact PV performance parameters, thus main aim of this work is to determine the optimum thickness of PAL as well as the temperature affectability on the PV performance of the cells. It was also observed that the maximum PV parameters (among the cells under consideration), viz. 29% PCE, are achieved with the formamidinium tin iodide (FASnI3) at the thickness of 600 nm. Similarly, the temperature of 300 K shows a much-improved efficiency offering nearly 29%. Further, the external quantum efficiency (EQE) and J-V also confirm the determent of the more stable, lead-free, FASnI3-based device, which can provide an effective way to develop highly efficient, low-cost solar cell devices.

Tunable transparent terahertz absorber for sensing and radiation warming

The lack in efficient functional devices has hindered plenty practical applications in terahertz (THz) band. In this work, we developed transparent THz absorber by employing trilayer Salisbury screen structure. Monolayer graphene and indium tin oxide (ITO) glass were spaced by a thin dielectric film, forming a transparent THz absorber. Assisted by ion gel, the carrier density of graphene layer can be effectively tuned through small external electrical gating (−2.5 V-2.5 V), with a modulation depth reaching to 100%. Taking advantage of the strong π−π interaction between graphene and external molecules containing π electrons, our fabricated transparent THz absorber enabled diphenylamine (DPA) detection. The adsorbed DPA molecule moves Fermi level of graphene toward Dirac point, performing a limit of detection of 5.5 ng. Moreover, by transferring the absorbed radiation into heat, our fabricated absorber can serve as a radiation warming device. The surface temperature of transparent THz absorber is 0.7 °C higher than that of glass in IR radiation environment. Note that the absorber is highly transparent in visible band, it will not prevent photosynthesis process of plants. Thereby, the THz absorbers have potential practical applications in diverse fields including wave manipulation, molecule sensing, and radiation warming.