Zirconia Surface Research Articles

Effect of water glass treatment for zirconia and silane coupling on bond strength of resin cement.

To evaluate the ability of the water glass treatment to penetrate zirconia and improve the bond strength of resin cement. Water glass was applied to zirconia specimens, which were then sintered. The specimens were divided into water-glass-treated and untreated zirconia (control) groups. The surface properties of the water-glass-treated specimens were evaluated using surface roughness and electron probe micro-analyser (EPMA) analysis. A resin cement was used to evaluate the tensile bond strength, with2 and without a silane-containing primer. After 24h in water storage at 37°C and thermal cycling, the bond strengths were statistically evaluated with t-test, and the fracture surfaces were observed using SEM. The water glass treatment slightly increased the surface roughness of the zirconia specimens, and the EPMA analysis detected the water glass penetration to be 50μm below the zirconia surface. The application of primer improved the tensile bond strength in all groups. After 24h, the water-glass-treated zirconia exhibited a tensile strength of 24.8 ± 5.5MPa, which was significantly higher than that of the control zirconia (17.6 ± 3.5MPa) (p < 0.05). After thermal cycling, the water-glass-treated zirconia showed significantly higher tensile strength than the control zirconia. The fracture surface morphology was mainly an adhesive pattern, whereas resin cement residue was occasionally detected on the water-glass-treated zirconia surfaces. The water glass treatment resulted in the formation of a stable silica phase on the zirconia surface. This process enabled silane coupling to the zirconia and improved the adhesion of the resin cement.

Unveiling the feature of deposition of oxygen and water molecules on the zirconium surface: A molecular dynamic study

Unveiling the feature of deposition of oxygen and water molecules on the zirconium surface at microscale is crucial during the initial stages of zirconium oxide layer formation in Pressurized Water Reactors (PWRs) or Light Water Reactors (LWRs). In this work, we use molecular dynamic simulations to study the feature of deposition of oxygen and water molecules on the zirconium surface. A special focus of this work is a formula our built for the number of atoms adsorbed by the metal surface at the considered moment of time. The results show that the surface density of atoms for the crystallographic plane (10−10) in is 3 times greater than that for the crystallographic plane (11−20). The effective surface density σ(10−10) for the crystallographic plane (10−10) is greater than the similar value σ(11−20) for the crystallographic plane (11−20). Furthermore, in a sufficiently wide range of temperatures, the mechanical properties of zirconium crystals during tensile deformation are practically independent of the diffusion of oxygen atoms along the grain boundaries. This distinct feature may be providing basis understanding for the experimental puzzle of oxidation rate of zirconium alloys.

Antibacterial Zirconia Surfaces from Organocatalyzed Atom-Transfer Radical Polymerization.

Antibacterial coatings are becoming increasingly attractive for application in the field of biomaterials. In this framework, we developed polymer coating zirconia with antibacterial activity using the "grafting from" methodology. First, 1-(4-vinylbenzyl)-3-butylimidazolium chloride monomer was synthesized. Then, the surface modification of zirconia substrates was performed with this monomer via surface-initiated photo atom transfer radical polymerization for antibacterial activity. X-ray photoelectron spectroscopy, ellipsometry, static contact angle measurements, and an atomic force microscope were used to characterize the films for each step of the surface modification. The results revealed that cationic polymers could be successfully deposited on the zirconia surfaces, and the thickness of the grafted layer steadily increased with polymerization time. Finally, the antibacterial adhesion test was used to evaluate the antibacterial activity of the modified zirconia substrates, and we successfully showed the antibacterial activity against Staphylococcus aureus and Pseudomonas aeruginosa strains.

Effects of Nano-Diamond-Coated Milling Bits on Cutting Dental Zirconia

Hard alloy end mills are commonly employed for milling zirconia prostheses in dentistry. Nano-diamond-coated milling bits ensure high processing efficiency, accuracy, extended tool life, and reduced processing costs. This study aims at comparing various effects of cutting dental zirconia with nano-diamond-coated and ordinary milling bits. Two types of milling bits, one with nano-diamond coating and one without, were used to cut the dental zirconia green blanks (Ø98.5 mm, thickness: 25 mm) at three different speeds (1000, 1500, and 2000 rpm) in a dental milling machine. The unsintered and sintered zirconia surfaces were evaluated with glossmeter, optical profilometer for surface roughness, SEM, and EDX. The glossiness of the sintered zirconia block was statistically higher than that of the unsintered block (p &lt; 0.05). For sintered zirconia, the nano-diamond-coated milling bit yielded a statistically (p &lt; 0.05) higher glossiness in all spindle speeds than uncoated, save for the uncoated milling bit used at 1500 rpm. However, in terms of roughness, only sintering showed to be a statistically significant factor (p &lt; 0.001) outweighing other two factors, and sintered zirconia always yielded lower surface roughness than the unsintered counterpart. Overall, the nano-diamond-coated milling bit can be operated at various speeds, resulting in a higher gloss on the sintered zirconia block, while an ordinary, uncoated milling bit can only achieve the same glossiness at a designated speed. The type of milling bits and the speeds have no significant effect on the surface roughness.

Comparison of Zirconia Implant Surface Modifications for Optimal Osseointegration.

Zirconia ceramic implants are commercially available from a rapidly growing number of manufacturers. Macroscopic and microscopic surface design and characteristics are considered to be key determining factors in the success of the osseointegration process. It is, therefore, crucial to assess which surface modification promotes the most favorable biological response. The purpose of this study was to conduct a comparison of modern surface modifications that are featured in the most common commercially available zirconia ceramic implant systems. A review of the currently available literature on zirconia implant surface topography and the associated bio-physical factors was conducted, with a focus on the osseointegration of zirconia surfaces. After a review of the selected articles for this study, commercially available zirconia implant surfaces were all modified using subtractive protocols. Commercially available ceramic implant surfaces were modified or enhanced using sandblasting, acid etching, laser etching, or combinations of the aforementioned. From our literature review, laser-modified surfaces emerged as the ones with the highest surface roughness and bone-implant contact (BIC). It was also found that surface roughness could be controlled to achieve optimal roughness by modifying the laser output power during manufacturing. Furthermore, laser surface modification induced a very low amount of preload microcracks in the zirconia. Osteopontin (OPN), an early-late osteogenic differentiation marker, was significantly upregulated in laser-treated surfaces. Moreover, surface wettability was highest in laser-treated surfaces, indicating favorable hydrophilicity and thus promoting early bone forming, cell adhesion, and subsequent maturation. Sandblasting followed by laser modification and sandblasting followed by acid etching and post-milling heat treatment (SE-H) surfaces featured comparable results, with favorable biological responses around zirconia implants.

Effect of Simulated Gastric Acid on the Interface Between Zirconia and Resin Cement.

To evaluate the effect of simulated gastric acid solution (SGAS) and resin cement composition on the shear bond strength (SBS) of zirconia-based materials with different levels of translucency to composite resin. A total of 40 medium-opacity (MO; 3Y-TZP) and 40 medium-translucency (MT; 4Y-PSZ) zirconia slabs were distributed into four groups according to the composition of the resin luting system (MDP free or with MDP [primer + Panavia V5]) and storage method (distilled water or SGAS [5% hydrochloric acid]). Composite resin cylinders were cemented on the zirconia surface and stored for 91 hours. SBS, failure mode, and surface characterization analyses via scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS) were performed. SBS data were analyzed using three-way ANOVA and Tukey tests, and failure mode was assessed using one-way ANOVA (P < .05). Storage media (P = .180), resin cement (P = .110), zirconia (P = .404), and their interactions did not affect SBS values. Bond strength ranged from 21.41 to 26.11 MPa. SEM images showed that SGAS modified the surface topography of zirconia and resin cement. The presence of chlorine and silicon (wt%) were higher after SGAS storage than after water storage in both cements used, while barium was higher only for the MDP cement. There was a prevalence of mixed failures for most of the groups. The SBS between both types of zirconia and resin cement was not affected by SGAS, although changes in zirconia topography were observed after SGAS exposure. The presence of MDP in the cement layer had no effect on the SBS challenged by SGAS.

Effect of Two Different Intraoral Polishing Systems on Surface Roughness, Color Stability, and Bacterial Accumulation of Zirconia-Reinforced Lithium Silicate Ceramic.

The aim of this study was to investigate the effects of two intraoral polishing methods on zirconia-reinforced lithium silicate ceramic after ultrasonic scaling. Thirty disc-shaped samples of zirconia-reinforced lithium silicate were constructed. Freshly extracted bovine teeth were collected and cleaned then the discs were cemented into a cavity prepared onto their labial surface. The samples were divided into three groups (10 samples per group); S: Scaling only, SE: Scaling followed by polishing using Eve Diapro lithium disilicate polishers, SD: Scaling followed by polishing using Diatech ShapeGuard ceramic polishing plus kit. The surface roughness was evaluated after scaling and polishing the samples. For color stability, the samples were stored for 12 days at 37°C in an incubator to simulate 1-year consumption of coffee. L*a*b* color parameters were assessed using VITA Easyshade Advance 4.0 before and after the staining procedure and the color difference was measured. Finally, bacterial accumulation was evaluated by incubating the samples with a suspension of Streptococcus mutans ( S. mutans), after that the S. mutans colonies were counted to obtain the values of colony-forming units (CFU). The final overall roughness, change in color and bacterial count were compared between all groups using one-way ANOVA and Tukey's post-hoc analysis. The Pearson correlation coefficient was used to determine the correlation between continuous variables. The cutoff for significance was chosen at p ≤ 0.05. Scaling induced surface roughness of the zirconia-reinforced lithium silicate ceramic was significantly decreased after using both intraoral polishing systems and this was accompanied by a significant decrease in color change and bacterial count. Intraoral polishing techniques can reduce the roughness of the surface of zirconia reinforced lithium silicate restorations induced due to scaling and subsequently reduce the stainability and bacterial accumulation.

Fracture strength of porcelain veneer on surface-treated zirconia.

In this study, we investigated the effects of surface treatment on the fracture strength of porcelain-veneered zirconia. Highly translucent 4 mol% yttria-stabilized zirconia disks (KATANA HT, Kuraray Noritake Dental) were divided into three surface-treatment groups: 1)as-sintered, 2) alumina sandblasted, and 3) ground. Crystallographic and surface-roughness analyses were conducted for each group. Veneering ceramics (Cerabien ZR, Kuraray Noritake Dental) were applied to the zirconia surfaces. The fracture strengths of the porcelain-veneered zirconia disks were measured using biaxial flexural-strength tests. Crystallographic analysis revealed that grinding and sandblasting increased the fractions of the monoclinic and rhombohedral zirconia phases. The ground specimens had a higher surface roughness than the sandblasted specimens. Weibull analysis showed no significant differences in biaxial flexural strength among the three groups. The results suggest that these surface treatments do not affect the fracture strength of porcelain-veneered zirconia.

3D Printed Porous Zirconia Biomaterials based on Triply Periodic Minimal Surfaces Promote Osseointegration In Vitro by Regulating Osteoimmunomodulation and Osteo/Angiogenesis.

The triply periodic minimal surface (TPMS) is a highly useful structure for bone tissue engineering owing to its nearly nonexistent average surface curvature, high surface area-to-volume ratio, and exceptional mechanical energy absorption properties. However, limited literature is available regarding bionic zirconia implants using the TPMS structure for bone regeneration. Herein, we employed the digital light processing (DLP) technology to fabricate four types of zirconia-based TPMS structures: P-cell, S14, IWP, and Gyroid. For cell proliferation, the four porous TPMS structures outperformed the solid zirconia group (P-cell > S14 > Gyroid > IWP > ZrO2). In vitro assessments on the biological responses and osteogenic properties of the distinct porous surfaces identified the IWP and Gyroid structures as promising candidates for future clinical applications of porous zirconia implants because of their superior osteogenic capabilities (IWP > Gyroid > S14 > P-cell > ZrO2) and mechanical properties (ZrO2 > IWP > Gyroid > S14 > P-cell). Furthermore, the physical properties of the IWP/Gyroid surface had more substantial effects on bone immune regulation by reducing macrophage M1 phenotype polarization while increasing M2 phenotype polarization compared with the solid zirconia surface. Additionally, the IWP and Gyroid groups exhibited enhanced immune osteogenesis and angiogenesis abilities. Collectively, these findings highlight the substantial impact of topology on bone/angiogenesis and immune regulation in promoting bone integration.

Comparison of the Intensity of Biofilm Production by Oral Microflora and Its Adhesion on the Surface of Zirconia Produced in Additive and Subtractive Technology: An In Vitro Study.

This in vitro study set out to find out how well oral cavity-dwelling bacteria can form biofilms and adhere on the surfaces of zirconium oxide samples created by 3D printing and milling technologies. 5 strains of microorganisms were used for the study, and 40 zirconium oxide samples were prepared, which were divided into two groups (n = 20)-20 samples produced using removal technology comprised the control group, while 20 samples produced by 3D printing technology comprised the test group. The prepared samples were placed in culture media of bacteria and fungi that naturally occur in the oral cavity. Then, the intensity of biofilm build-up on the samples was determined using qualitative and quantitative methods. The results for both materials were compared with each other. No variations in the degree of biofilm deposition on zirconium oxide samples were found for the microorganisms Streptococcus mutans, Pseudomonas aeruginosa, Enterococcus faecalis, and Staphylococcus aureus. For Candida albicans fungi, more intense biofilm deposition was observed on samples made using 3D printing technology, but these differences were not statistically significant. The biofilm accumulation intensity of ceramics produced by additive technology is comparable to that of milled zirconium oxide, which supports the material's broader use in clinical practice from a microbiological perspective. This ceramic has demonstrated its ability to compete with zirconium oxide produced by milling techniques in in vitro experiments, but sadly, no in vivo tests have yet been found to determine how this material will function in a patient's oral cavity.

Mussel-Inspired Construction of Silica-Decorated Ceramic Membranes for Oil–Water Separation

In recent years, ceramic membranes have received widespread focus in the area of liquid separation because of their high permeability, strong hydrophilicity, and good chemical stability. However, in practical applications, the surface of ceramic membranes is prone to be contaminated, which degrades the permeation flux of ceramic membranes during the separation process. Inspired by mussels, we imitate the biomimetic mineralization process to prepare a ceramic membrane of nano–silica on the pre-modified zirconia surface by co-deposited polydopamine/polyethyleneimine. The modified ceramic membranes were utilized for the purpose of oil–water separation. Separation performance has been tested using a disc ceramic membrane dynamic filtration device. The outcomes revealed an enhanced permeability in the modified membrane, measuring as 159 L m−2 h−1 bar−1, surpassing the separation flux of the unmodified membrane, which was 104 L m−2 h−1 bar−1. The permeation performance of the modified membrane was increased to 1.5 times. Modified ceramic membranes are highly resistant to fouling. From the beginning to the end of separation process, the oil rejection rate of the modified ceramic membrane is always higher than 99%. After a 2 h oil–water separation test run, modified ceramic membrane permeate flux can be restored to 91% after cleaning. It has an enormous capacity for application in the area of oil–water separation.

Repair of monolithic zirconia restorations with different direct resin composites: effect on the fatigue bonding and mechanical performance

ObjectiveThe study aims to evaluate the shear bond and flexural strength fatigue behavior of yttrium-stabilized zirconia (4YSZ) repaired using different resin composites.Materials and methodsCylindric specimens of 4YSZ were obtained for the bond strength (Ø = 6 mm, 1.5 mm of thickness) and biaxial flexural strength (Ø = 15 mm, 1 mm of thickness) fatigue tests and divided into 3 groups according to the repair resin composite: EVO (nanohybrid), BULK (bulk-fill), and FLOW (flowable). The zirconia surface was air-abraded with alumina particles, a 10-methacryloyloxydecyl dihydrogen phosphate (10-MDP) primer was applied, and the resin composite was build-up over the zirconia. Fatigue shear bond strength and flexural fatigue strength tests were performed (n = 15). One-way ANOVA and Tukey post hoc tests were carried out for both outcomes, besides scanning electron microscopy and finite element analysis.ResultsThe repair material affected the fatigue shear bond strength of zirconia ceramic. The BULK group (18.9 MPa) depicted higher bond strength values than FLOW (14.8 MPa) (p = 0.04), while EVO (18.0 MPa) showed similar results to both groups. No effect was observed for the mechanical behavior (p = 0.53). The stress distribution was similar for all groups.ConclusionThe repair of yttrium-stabilized zirconia (4YSZ) ceramics with bulk-fill resin composites was the best option for high fatigue bond strength. However, the fatigue mechanical performance was similar regardless of the applied repair material.Clinical relevanceThe repair of yttrium-stabilized zirconia (4YSZ) monolithic restorations may be performed with nanohybrid and bulk-fill resin composites in order to promote longevity in the treatment.

Effect of zirconia surface conditioning before glazing on the wear of opposing enamel: an in vitro study.

This in vitro study aimed to evaluate the wear of natural teeth opposing 3mol% yttria-stabilized tetragonal zirconia polycrystal (3Y-TZP) with different surface conditions. Sixty 3Y-TZP specimens were randomly assigned to six groups (n = 10), differing in surface condition. In three groups, the samples underwent glazing-with the glaze applied to roughened (i.e., 106-µm-grit diamond-finished), as-sintered, and polished zirconia. The three remaining groups consisted of unglazed specimens: solely polished samples and diamond-finished samples (106-µm-grit and 46-µm-grit) without further conditioning. Two-body wear was evaluated at extracted, non-carious molars (n = 60), which served as antagonists in chewing simulation (10,000 masticatory cycles, 49N load). As a control, natural teeth with intact enamel surfaces were tested against natural molars (n = 10). All samples were 3D-scanned before and after the chewing simulation (7 Series, Straumann). Volume loss was calculated (Inspect Software, GOM), and statistically analyzed (SPSS Statistics 24, IBM). Volume loss of the natural antagonists decreased in the following order: 106-µm-grit diamond-finished zirconia (4.6 ± 2.5 mm3), glazed 106-µm-grit diamond-finished zirconia (3.8 ± 1.1 mm3), glazed as-sintered zirconia (3.5 ± 0.9 mm3), 46-µm-grit diamond-finished zirconia (1.7 ± 0.6 mm3), control (1.6 ± 0.7 mm3), glazed polished zirconia (1.4 ± 0.5 mm3), and solely polishing (0.4 ± 0.2 mm3). Even when polishing the surfaces before glazing, volume loss was not mitigated to the same extent as after polishing alone. The zirconia surface condition beneath the glazing influences antagonist wear. Although polishing before glazing resulted in acceptable levels of antagonist wear, this approach did not yield as favorable results as polishing alone. For operators favoring glazing, pre-polishing the zirconia surface could be advantageous to reduce wear.

Effects of Surface Textures Created Using Additive Manufacturing on Shear Bond Strength Between Resin and Zirconia.

This investigation aimed to assess the impact of additive manufacturing-generated surface textures on zirconia bond strength. Zirconia samples (n = 144) fabricated using digital light-processing (DLP) technology were categorized into 6 groups according to the type of surface conditioning (group NN: no designs, no air abrasion; group NY: no designs, with air abrasion; group GN: groove designs, no air abrasion; group GY: groove designs with air abrasion; group HN: hexagon grid, no air abrasion; group HY: hexagon grid, with air abrasion). Composite resin cylinders were cemented to the treated zirconia surfaces with dual-curing, self-adhesive resin cement (Clearfil SA Luting). The shear bond strength (SBS) was tested after water storage for 3 days or 3 days with an additional 10,000 thermocycles. The zirconia samples fabricated using DLP technology have high accuracy. The SBS of the NY, GY, and HY groups did not significantly differ after 3 days, and neither did the SBS of the NN, GN, and HN groups. The NN, NY, and HY groups exhibited reduced SBS compared to their initial values following artificial aging, while the SBS of the remaining three groups were not diminished. The GY group obtained the highest SBS value after aging. Printing grooves with air abrasion can improve the bond strength.

Enhancing angiogenesis in peri-implant soft tissue with bioactive silk fibroin microgroove coatings on zirconia surfaces.

Zirconia abutments and restorations have improved the aesthetic appeal of implant restoration, yet peri-implantitis poses a significant threat to long-term success. The soft tissue surrounding implants is a crucial biological barrier against inflammation and subsequent bone loss. Peri-implantitis, akin to periodontitis, progresses rapidly and causes extensive tissue damage. Variations in tissue structure significantly influence disease progression, particularly the lower vascular density in peri-implant connective tissue, compromising its ability to combat infection and provide essential nutrients. Blood vessels within this tissue are vital for healing, with angiogenesis playing a key role in immune defense and tissue repair. Enhancing peri-implant soft tissue angiogenesis holds promise for tissue integration and inflammation control. Microgroove surfaces have shown potential in guiding vessel growth, but using subtractive technologies to carve microgrooves on zirconia surfaces may compromise mechanical integrity. In this study, we utilized inkjet printing to prepare bioactive silk fibroin microgrooves (SFMG) coating with different sizes on zirconia surfaces. SFMG coating, particularly with 90 µm width and 10 µm depth, effectively directed human umbilical vein endothelial cells (HUVECs) along microgrooves, promoting their proliferation, migration, and tube formation. The expression of vascular endothelial growth factor A and fibroblast growth factor in HUVECs growing on SFMG coating was upregulated. Additionally, the SFMG coating activated the PI3K-AKT pathway and increased glycolytic enzyme gene expression in HUVECs. In conclusion, SFMG coating enhances HUVEC growth and angiogenesis potential by activating the PI3K-AKT pathway and glycolysis, showing promise for improving tissue integration and mitigating inflammation in zirconia abutments and restorations.

Adsorption of oral antibacterial agents on zirconia surfaces with different crystal systems.

Zirconia ceramics are widely used as dental prosthetics owing to their high biocompatibility, excellent mechanical strength, and aesthetic properties similar to color tones of natural teeth. However, there exists a growing demand for the facile attachment of antibacterial properties in long-term dental restoration. Thus, in this study, we evaluated the adsorption ability of cetylpyridinium chloride (CPC) and benzalkonium chloride (BKC)-quaternary amines widely used as antibacterial substances in commercial toothpaste and other oral care products-onto zirconia surfaces with tetragonal and monoclinic crystal structures. Although tetragonal zirconia has been widely used in dental prosthetic materials such as crowns etc., monoclinic zirconia has also been used under oral conditions because of long-term implantation. When antibacterial molecule loading on zirconia powders under simulated oral conditions, it was revealed that monoclinic zirconia adsorbed approximately five times more CPC and BKC per unit area compared with that of tetragonal zirconia. Moreover, in tetragonal zirconia, the adsorption amounts of both CPC and BKC increased slightly with growing Y2O3 content as a stabilizer. This phenomenon was attributable to the formation of complexes between rare earth elements (REE) such as Y2O3 in zirconia and quaternary amines such as CPC and BKC. In this study, the antibacterial molecular adsorption ability of dental zirconia was observed, and new advantages of zirconia in dental applications were discovered.

Mechanical and optical properties of a borosilicate glass used to improve the finishing of 3Y-TZP restorations.

Borosilicate glass was developed to enhance the mechanical behavior and smoothness of dental zirconia as an alternative to conventional glaze. This study assessed the mechanical and optical properties of 3 mol% yttria-stabilized tetragonal zirconia polycrystal (3Y-TZP) coated with borosilicate glass or a commercial glaze fired for an extended period of time. Disc-shaped 3Y-TZP zirconia specimens (Zpex, Tosoh) were sintered at 1550°C for 2 hours. The specimens were divided into three groups: as-sintered (control, C); commercial glaze (G); and borosilicate glass (SL). The glaze and borosilicate glass were applied over the zirconia and fired for 20 minutes at 950°C and 1200°C, respectively. Biaxial flexural strength, fractography, X-ray diffraction (XRD), roughness (Ra and Rz), fracture toughness (Vickers indentation method), color difference (∆E00), and translucency (TP00) analyses were conducted. The t-test or the one-way ANOVA and Tukey's tests were used to analyze the data (α = 0.05). Flexural strength data were subjected to the Weibull analysis. The SL group exhibited the highest flexural strength (1025.8 MPa), whereas the C (859.41 MPa) and G (816.0 MPa) groups exhibited similar values. The SL group also had the highest characteristic strength. The fracture origin in all groups was on the zirconia surface. XRD analysis revealed that the specimens from the SL group contained tetragonal, cubic, and monoclinic phases. The SL group presented the lowest surface roughness. Fracture toughness in the SL group was lower than in the C group, but similar to that observed in the G group. The translucency and color differences observed in the G and SL groups were similar. Borosilicate glass enhanced the flexural strength of 3Y-TZP, promoted the smoothest surface, and exhibited optical properties similar to those of the glaze.

The impact of CO2 laser on the bond strength of translucent zirconia and traditional zirconia with the resin cement: In vitro study

Background/Aim: The aim of this study is to compare the impact of CO 2 laser on traditional zirconia and translucent zirconia in terms of the bonding strength to resin cement. Material and Methods: In this in-vitro study 20 zirconia disks (10 mm diameter and 2 mm thickness) were assigned to two groups (n = 10). Group 1: 10 discs of traditional zirconia, Group 2: 10 discs of translucent zirconia, CO 2 lasers were used for pretreatment of zirconia surface, respectively. Dentinal disks were cemented on zirconia disk using dual-curing resin cement. Shear bond strength tests were performed at a crosshead speed of 1 mm/min after 24 h distilled water storage. Data was analyzed by T Student's test. Results: The means and standard deviations of shear bond strength values in Group 1, and Group 2 were 1.15, 0.38, 1.99 , 0.65 MPa respectively. Data showed that application of CO 2 laser resulted in a significant higher shear bond strength of resin cement to translucent zirconia ceramics (p &lt; 0.05). Conclusions: Application of CO 2 laser treatment (3W) increases the bond strength to the resin cement of translucent zirconia compared to traditional zirconia.

Shear bond strength between standard or modified zirconia surfaces and two resin cements incorporating or not 10-MDP in their matrix

ObjectiveThis study aimed first to compare the shear bond strength between zirconia samples luted to enamel with a 10-MDP- containing resin cement (Panavia F2.0, Kuraray, Japan) and those luted with a resin cement using a separated 10-MDP monomer-containing bottle (Panavia V5, Kuraray, Japan). The second objective was to evaluate the bond stability after 150 days of aging in water, between enamel and zirconia ceramic surface enhanced with a glass-ceramic coating. Materials and methods80 specimens composed of ceramic cylinders and enamel disks were obtained, within eight experimental groups (n = 10). 60 zirconia cylinders (Katana STML zirconia, Kuraray, Japan) were assigned to 3 groups according to their surface treatment: milled/sintered surface (ZRCT), tribochemical silica-coating (Cojet™ Sand, 3 M ESPE, Seefeld, Germany) (ZRTC), and glass-ceramic coating (IPS e.max Zirpress) (ZRZP). 20 cylinders of lithium disilicate had a milled surface (IPS e.max CAD, Ivoclar-Vivadent, Schaan, Liechtenstein) (ECAD). The cylinders of each group were further divided into two subgroups according to the resin cement used: Panavia F2.0 (-PF) and Panavia V5 (-PV). All specimens were stored in distilled water for 150 days before shear bond strength (SBS) tests. The fracture mode was analyzed, and data were statistically computed (two-way ANOVA, post hoc Tukey test, p < 0.05, SPSS, IBM, v26). ResultsThe ECAD-PF group recorded the highest SBS values (31.75 ± 2.2), and the ZRCT-PF group recorded the lowest values (5.59 ± 1.1). The two-way ANOVA test showed that ceramic surface treatment had a statistically significant effect on SBS (F (3,72) = 38.95, p < 0.001) while the type of ARC did not (F (1,72) = 2.40, p = 0.126). Tukey’s post hoc test revealed no statistical difference between the ZRZP and the ZRTC or ECAD groups. ConclusionWithin the limitations of this study, the PV resin achieved similar shear bond strength results between tribocoated zirconia and enamel compared to the one for glass-ceramic and enamel. Furthermore, a long-term durable bond, similar to the glass-ceramic one, was achieved with the heat pressed ceramic coated specimens. Thus, this new surface treatment could be recommended for anterior cantilever bridges for its fracture resistance and bonding ability.

An In Vivo Investigation of Non-Metallic vs. Metallic Hand Scalers on Zirconia Implant-Supported Crowns: A Year-Long Analysis of Peri-Implant Maintenance.

This study examined whether the degree of abutment surface modification that may occur with regular periodontal instrumentation has a clinical impact in terms of increased plaque accumulation and increased peri-implant tissue inflammation on zirconia implant abutments. Thirteen patients who had zirconia implant crowns were recruited in this randomized clinical trial. Each patient acted as their control and had either the buccal or lingual surface of their screw-retained implant restoration scaled with a metallic scaler and the other surface with a non-metallic scaler at 3, 6, 9, and 12 months. Cytokine testing of the peri-implant crevicular fluid was completed at 0, 3, and 12 months for IL-2, IL-4, IL-6, IL-8, IL-10, TNF-α, or IFNγ. Implant crowns were removed at 12 months and evaluated under an atomic force microscope for the average roughness (Ra). The implant crowns were polished and re-inserted. The results were analyzed using the Kruskal-Wallis test, and post hoc tests were conducted with a significance level of α = 0.05. Significant differences in surface roughness (Ra) were observed between the metallic and non-metallic scalers. The median Ra values were 274.0 nm for metallic scalers and 147.1 nm for non-metallic scalers. However, there were no significant differences between the type of scaler used and the amount of clinical inflammation or cytokine production. Metallic scalers produced deeper, more aggressive surface alterations to the abutment/crown zirconia surface, but there was no statistically significant difference between the degree of surface alterations, amount of BOP, and the amplitude of cytokine inflammation produced.