Powder X-ray Diffraction Studies Research Articles

Tuning of thermoelectric performance by modulating vibrational properties in Ni-doped Sb2Te3.

Sb2Te3, a binary chalcogenide-based 3D topological insulator, attracts significant attention for its exceptional thermoelectric performance. We report the vibrational properties of magnetically doped Sb2Te3 thermoelectric material. Ni doping induces defect/disorder in the system and plays a positive role in engineering the thermoelectric properties through tuning the vibrational phonon modes. Synchrotron powder X-ray diffraction study confirms good crystalline quality and single-phase nature of the synthesized samples. The change in structural parameters, including Biso and strain, further corroborate with structural disorder. Detailed modification of phonon modes with doping and temperature variation is analysed from temperature-dependent Raman spectroscopic measurement. Compressive lattice strain is observed from the blue shift of Raman peaks owing to Ni incorporation in Sb site. An attempt is made to extract the lattice thermal conductivity from total thermal conductivity estimated through optothermal Raman studies. Hall concentration data support the change in temperature-dependent resistivity and thermopower. Remarkable increase in thermopower is observed after Ni doping. Simulation of the Pisarenko model, indicating the convergence of the valence band, explains the observed enhancement of thermopower in Sb2-xNixTe3. The energy gap between the light and heavy valence band at Γ point is found to be 30 meV (for Sb2Te3), which is reduced to 3 meV (in Sb1.98Ni0.02Te3). A significant increase in thermoelectric power factor is obtained from 715 μWm-1K-2 for pristine Sb2Te3 to 2415 μWm-1K-2 for Ni-doped Sb2Te3 sample. Finally, the thermoelectric figure of merit, ZT is found to increase by four times in Sb1.98Ni0.02Te3 than that of its pristine counterpart.

Ni Single Atom Decorated Porous Hollow Carbon Nanosphere-Based Electrodes for High Performance Symmetric Solid-State Supercapacitors.

Ni single atom containing hollow carbon nanospheres with nitrogen doping has been synthesized by carbonization of Ni(NO3)2/phloroglucinol-formaldehyde polymer/silica composite. The samples have been characterized by powder X-ray diffraction, nitrogen adsorption/desorption, electron microscopic, Raman and X-ray photoelectron spectroscopic studies. The microstructure and surface area vary with the amount of Ni(NO3)2 employed in the syntheses and the carbonization environment. An optimized amount of nickel and argon as the carbonization gas afford Ni-1.0@N@HCN-Ar which possesses overall superior features. The uniformly dispersed Ni single atoms within the hollow porous carbon framework fully utilize all the electroactive sites thereby improving the supercapacitive performance. The specific capacitance of Ni-1.0@N@HCN-Ar reaches 777 F∙g-1 at 1 A∙g-1 with a Coulombic efficiency of 98.4% and excellent recyclability. The energy and power density of Ni-1.0@N@HCN-Ar are found to be high; at 1 A∙g-1 its energy density is 155.4 Wh∙kg-1 with a power density of 600.3 W∙kg-1. At a high current density of 10 A∙g-1 the material shows a high energy density of 118.4 Wh∙kg-1 with excellent power density of 6003.4 W∙kg-1. A symmetric solid-state supercapacitor assembled with this material, Ni-1.0@N@HCN-Ar//Ni-1.0@N@HCN-Ar using H2SO4/PVA gel electrolyte shows a superior energy density value of 30 Wh∙kg-1 at a power density of 1200 W∙kg-1.

Influence of pH on growth, structural, thermal, linear and nonlinear optical properties of L-asparagine monohydrate single crystal

This report presents investigation on influence of pH on growth, structural, thermal, linear and nonlinear optical properties of L-asparagine monohydrate (LAM) single crystal for the first time. Single crystals of LAM were grown at different pH by solution growth method by allowing slow evaporation of solvent. Crystal grown at pH 6.4 grows slowly as compare to other crystals grown at other pH values. The slight variation in lattice parameters of grown crystals has been confirmed by powder X-ray diffraction study. FT-IR study confirms the presence of functional groups of LAM in all grown crystals. Influence of pH on optical quality of crystals has been discussed. The crystal grown at pH 5.4 has maximum optical transparency and shows 2 and 20 % more transmission than crystals grown at pH 4.4 and 6.4, respectively. Other optical parameters like cutoff wavelength (λmax), band gap (Eg), linear refractive index (n), reflectance, extinction coefficient (k), electrical susceptibility (χ), optical conductivity(σop), electrical conductivity (σel) and Urbach energy (Eu) of all crystals have been evaluated from transmission data. The LAM crystal grown at pH 6.4 show high values of third order nonlinear optical parameters, as compare to other grown crystals, that attest its suitability for applications like higher harmonic generation, optical switching, optical limiting and other photonic applications over other grown crystals. Thermal stability of the grown crystals has been attested by TG-DTA study.

Intramolecular Charge Transfer and Stimuli-Responsive Emission in Cholesterol-Appended Phenothiazine-Cyanostyryl-Based Donor-Acceptor Systems.

Organic fluorescent molecules have received considerable attention owing to their various optoelectronic applications. Herein, we report the design and synthesis of two cholesterol-functionalized cyanostyrene-phenothiazine-based D-π-A systems that are emissive in both the solution and solid states. The newly synthesized cholesterol-appended phenothiazine-cyanostyrene diads PTCS-1 and PTCS-2 vary in the N-alkylation of phenothiazine, respectively, with─octyl and─hexyl chains. Both molecules are highly fluorescent and show reasonably good quantum yields in nonpolar solvents because of twisted intramolecular charge transfer (TICT). The molecules exhibit aggregation-induced emission in the solid state. Due to the presence of flexible alkyl chains in the phenothiazine and cholesterol moieties, PTCS-1 and PTCS-2 show mechanochromic luminescence switching in response to external shear stress and emission recovery under methanol vapor. Powder X-ray diffraction studies prove that the emission switching on the applied stimuli in both PTCS-1 and PTCS-2 is attributed to the reversible transformation between the crystalline and amorphous states. Time-dependent density functional theory (TD-DFT) studies are carried out to gain insight into the ICT interactions. TD-DFT analysis at the TD-M06-2X/def2-TZVP level further revealed that in both molecules, the lowest unoccupied molecular orbital (LUMO) + 2, LUMO, highest occupied molecular orbital (HOMO), and HOMO - 1 orbitals are responsible for the charge transfer interactions. These ICT interactions are identified as π-π* type interactions.

-Doped Cerium Oxide on rGO: A Hydrothermal Approach for High-Performance Supercapacitors

This work describes the hydrothermal method for synthesizing a novel nanocomposite: Nickel -doped Cerium oxide on reduced graphene oxide (Ni-CeO2/rGO). The resulting material exhibits exceptional electrocatalytic behavior, showing promise for supercapacitor applications. The Phase morphology, elemental analysis, surface area and oxidation state were confirmed by powder X-ray diffraction studies (PXRD), Raman spectrum, High Resolution Transmission Electron Microscopy (HRTEM), Field Emission Scanning Electron Microscopy (FESEM) and Energy Dispersive X-ray (EDX), Brunauer-Emmett Teller (BET) and XPS respectively. Electrochemical analysis involving cyclic voltammetry (CV), Galvanostatic charge/ discharge, and Electrochemical impedance spectroscopy (EIS). The specific capacitance is 262.1Fg-1, 504Fg-1, and 728Fg-1 for CeO2, CeO2/rGO, Ni-CeO2/rGO it depicts its suitability for energy storage. This study establishes the Ni-CeO2/rGO nanocomposite as a highly effective material for advanced energy storage applications.

Effect of Polymorphism on the Sorption Properties of a Flexible Square-Lattice Topology Coordination Network.

The stimulus-responsive behavior of coordination networks (CNs), which switch between closed (nonporous) and open (porous) phases, is of interest because of its potential utility in gas storage and separation. Herein, we report two polymorphs of a new square-lattice (sql) topology CN, X-sql-1-Cu, of formula [Cu(Imibz)2]n (HImibz = {[4-(1H-imidazol-1-yl)phenylimino]methyl}benzoic acid), isolated from the as-synthesized CN X-sql-1-Cu-(MeOH)2·2MeOH, which subsequently transformed to a narrow pore solvate, X-sql-1-Cu-A·MeOH, upon mild activation (drying in air or heating at 333 K under nitrogen). X-sql-1-Cu-A·MeOH contains MeOH in cavities, which was removed through exposure to vacuum for 2 h, yielding the nonporous (closed) phase X-sql-1-Cu-A. In contrast, a more dense polymorph, X-sql-1-Cu-B, was obtained by exposing X-sql-1-Cu-(MeOH)2·2MeOH directly to vacuum for 2 h. Gas sorption studies conducted on X-sql-1-Cu-A and X-sql-1-Cu-B revealed different switching behaviors to two open phases (X-sql-1-Cu·CO2 and X-sql-1-Cu·C2H2), with different gate-opening threshold pressures for CO2 at 195 K and C2H2 at 278 K. Coincident CO2 sorption and in situ powder X-ray diffraction studies at 195 K revealed that X-sql-1-Cu-A transformed to X-sql-1-Cu-B after the first sorption cycle and that the CO2-induced switching transformation was thereafter reversible. The results presented herein provide insights into the relationship between two polymorphs of a CN and the effect of polymorphism upon gas sorption properties. To the best of our knowledge, whereas sql networks such as X-sql-1-Cu are widely studied in terms of their structural and sorption properties, this study represents only the second example of an in-depth study of the sorption properties of polymorphic sql networks.

Fabrication, characterization and application of W/N co-doped zinc oxide nanoparticles as a promising photoanode for dye-sensitized solar cells

In the present investigation, undoped, W doped, and W/N co-doped ZnO nanoparticles were prepared by sol–gel route. Here, the ZnO layers were fabricated via the doctor blade method. Hexagonal wurtzite structure is determined by XRD studies. The formation of a hexagonal wurtzite structure was observed from X-ray powder diffraction (XRD) resulting in a slight increase in crystallite size with an increase in doping content. The UV observation shows that W/N co-doping shifted the absorption spectra towards a higher wavelength and reduces the band gap energy. The EDS spectra confirms the high purity and triumphant doping of the W(tungsten) and N(nitrogen) into the ZnO lattice. The morphology of undoped and W/N co-doped ZnO nanoparticles was demonstrated by using FESEM and HRTEM. The 2 % W and 1.5 % N co-doped ZnO photoanode based DSSC (dye-sensitized solar cells) gained the highest short circuit current density of 8.44 mAcm−2 having an open-circuit voltage of 0.65 V, and PCE (power conversion efficiency) of 3.60 %.

Application of ultrasound-assisted compression and 3D-printing semi-solid extrusion techniques to the development of sustained-release drug delivery systems based on a novel biodegradable aliphatic copolyester

The purpose of this study was to investigate the ability of two advanced hot-processing technologies, Ultrasound-Assisted Compression (USAC) and 3D-printing Semi-solid Extrusion (SSE), to manufacture sustained-release drug delivery systems based on a novel biodegradable aliphatic copolyester. The copolymer was synthesized from ω-pentadecalactone (PDL), 1,4-cyclohexanedimethanol (CHDM) and dimethyl succinate (DMS) (monomer ratio PDL/CHDM/DMS 70/30/30) by enzymatic ring opening polymerization and two-step melt polycondensation processes and has a random microstructure, a high molecular weight (107,100 g mol−1) and a relatively low melting point (∼65 °C). The antibacterial agent metronidazole (MTZ) was chosen as model drug and binary physical mixtures copolymer:drug were prepared at 90:10 and 70:30 w/w ratios. Thermal analysis studies evidenced that the formulations could be processed below their degradation temperatures. Drug delivery devices with dense and meshed structures were manufactured using USAC and SSE techniques, respectively, with USAC devices exhibiting more reproducible physical properties than the SSE systems. Powder X-ray diffraction and scanning electron microscopy studies showed a partial sintering of the copolyester during USAC processing while MTZ remained mostly crystalline. In contrast, the copolymer melted and the drug underwent some amorphization when processed using SSE. In vitro drug release studies in phosphate buffer (pH 6.8) showed that, after an initial burst release of metronidazole, USAC and SSE devices exhibited a prolonged and/or sustained drug release over 20 days. The initial burst release was dependent on the manufacturing technique and the drug/polymer ratio, being minimized for SSE devices containing 10 wt% MTZ. The whole drug release profiles fitted well to the Peppas-Sahlin model, being drug diffusion the predominant release mechanism. After the burst release, the sustained release period of USAC and SSE devices containing 10 wt% MTZ showed a good fit to the zero-order kinetic model, with faster drug release from the SSE devices due to the larger surface area of their meshed structure. In conclusion, this work demonstrates that processing the aliphatic copolyester by both USAC and SSE technologies provides an attractive strategy to manufacture biodegradable drug delivery systems for long-term release of metronidazole.

Structure, Self-Assembly, and Phase Behavior of Neuroactive N-Acyl GABAs: Doxorubicin Encapsulation in NPGABA/DPPC Liposomes and Release Studies.

N-Acylated amino acids and neurotransmitters in mammals exert significant biological effects on the nervous system, immune responses, and vasculature. N-Acyl derivatives of γ-aminobutyric acid (N-acyl GABA), which belong to both classes mentioned above, are prominent among them. In this work, a homologous series of N-acyl GABAs bearing saturated N-acyl chains (C8-C18) have been synthesized and characterized with respect to self-assembly, thermotropic phase behavior, and supramolecular organization. Differential scanning calorimetric studies revealed that the transition enthalpies and entropies of N-acyl GABAs are linearly dependent on the acyl chain length. The crystal structure of N-tridecanoyl GABA showed that the molecules are packed in bilayers with the acyl chains aligned parallel to the bilayer normal and that the carboxyl groups from opposite layers associate to form dimeric structures involving strong O-H···O hydrogen bonds. In addition, N-H···O and C-H···O hydrogen bonds between amide moieties of adjacent molecules within each layer stabilize the molecular packing. Powder X-ray diffraction studies showed odd-even alternation in the d spacings, suggesting that the odd chain and even chain compounds pack differently. Equimolar mixtures of N-palmitoyl GABA and dipalmitoylphosphatidylcholine (DPPC) were found to form stable unilamellar vesicles with diameters of ∼300-340 nm, which could encapsulate doxorubicin, an anticancer drug, with higher efficiency and better release characteristics than DPPC liposomes at physiologically relevant pH. These liposomes exhibit faster release of doxorubicin at acidic pH (<7.0), indicating their potential utility as drug carriers in cancer chemotherapy.

Oral pH triggered colon-specific ketoprofen loaded microspheres for the better management of early morning symptoms associated with rheumatoid arthritis. Part I: Optimization, in-vitro, and ex-vivo characterization

The primary goal of this research was to investigate pH-triggered colon-specific ketoprofen-loaded microspheres (C-SKLM) using Eudragit S-100 as a pH-dependent polymer. The formulation was optimized using the Box-Behnken design. The suggested C-SKLM formulation with the amount of ketoprofen = 189.09 mg, the amount of Eudragit-100 = 600 mg, and the paddle speed = 400 rpm showed a considerable particle size (106 µm), drug encapsulation efficacy (79.67%), and % cumulative drug release at 5th hr (8.62) and 10th hr (92.62) for oral administration. Microphotographs of scanning electron microscopy indicated that the optimized C-SKLM was smooth and spherical. The differential scanning calorimetry and X-ray powder diffraction studies have shown that ketoprofen was dispersed in the polymer in its optimized C-SKLM formulation, and the spectra from the Fourier transform infrared study have shown no significant drug-polymer interaction. Ex-vivo permeation studies on isolated rat gastro-intestinal segments revealed that the maximum amount of ketoprofen permeated after 2 h through the isolated stomach (0.559 ± 0.049 mg), small intestine (1.36 ± 0.226 mg), and colon (0.972 ± 0.068 mg) was observed for ketoprofen pure. In contrast, a significantly lesser amount of the drug was permeated through the stomach (0.1 ± 0.025 mg) and small intestine (0.28 ± 0.1 mg) than the colon (0.697 ± 0.23 mg) from the ketoprofen-loaded microspheres formulation. In-vitro and ex-vivo permeation studies suggest that the developed C-SKLM could be helpful for the effective management of early morning symptoms due to rheumatoid arthritis by delaying the release by targeting the colon.

Highly Efficient Non-Enzymatic Electrochemical Glucose Biosensor Based on Copper Metal Organic Framework Coated on Graphite Sheet

Detection of glucose is highly informative, creating a constant demand for fabricating high-precision glucose biosensors. Metal–organic frameworks, a family of porous materials renowned for their tunability, can be an excellent choice for developing such sensors. We have developed a highly-sensitive, non-enzymatic sensor for electrochemical detection of glucose fabricated using Copper Metal–Organic Framework (Cu MOF), synthesized by a simple, room-temperature stirring method using Benzene-1,3,5-tricarboxylic acid (BTC) as ligand and Copper nitrate trihydrate as precursor. The synthesized nanostructure was characterized using Fourier transform infrared spectroscopy, scanning electron microscopy, and energy-dispersive X-ray analytical techniques. Powder X-ray diffraction study and thermogravimetric analysis were also done. Further, Brunnauer-Emmett-Teller analysis revealed the porous nature of Cu MOF. The materials exhibited strong electro-catalytic activity for glucose oxidation as revealed from cyclic voltammetry and chronoamperometric studies done under alkaline pH conditions. The Cu MOF deposited on a conducting graphite sheet electrode displayed a significantly low detection limit of 0.019 mM through a broad detection range (1–15 mM) and a strong sensitivity of 229.4 μAmM−1 cm2. Overall, the Cu MOF/GS exhibits exceptional stability, short response time (less than 1 s), and good repeatability and reproducibility, making it a promising future material for non-enzymatic glucose detection.

Synthesis, structural elucidation and characterization of a new organic single crystal Guanidinium adipate monohydrate (GuAM) for nonlinear optical applications

A slow evaporation solution growth process was employed to grow a new organic single crystal Guanidinium adipate monohydrate (GuAM) at room temperature. The structure refinement and cell specifications were elucidated using the X-ray diffraction method. Single crystal XRD study revealed that the grown crystal crystallized in the monoclinic system with unit cell dimensions a = 4.948 (9) Å; b = 16.770 (2) Å; c = 13.554 (2) Å; α and γ = 90.00⁰; β = 95.302⁰ (3), V = 1120.1(3) Å3 and Z = 4. The structure of the crystal was solved by direct method and refined by full matrix least-square method using SHELXL-2018/3 program. The crystalline nature of the sample was evaluated by powder X-ray diffraction (PXRD) study. Fourier transform infrared (FTIR) spectral study was employed to recognize the diverse functional groups present in the synthesized crystal. Optical attributes such as absorbance and emission nature of the GuAM were explored using UV–visible-NIR absorbance study and photoluminescence study respectively. The laser damage threshold value of the formed crystal has been determined by employing an Nd-YAG laser with a wavelength of 1064 nm. The mechanical nature of the GuAM was examined utilizing Vicker's microhardness test and other related parameters were also calculated. TGA-DTA analysis was utilized to estimate the title crystal's thermal stability. The Z-scan technique has been employed to gain insight into the third order nonlinear (NLO) parameters of the GuAM. These findings imply that guanidinium adipate monohydrate (GuAM), a grown single crystal, may be a viable choice for NLO applications.

Selective Detection of Primary Aromatic Amines through Enhanced Luminescence of a 2D + 2D Inclined Polycatenated Microporous Nitro-Functionalized Metal-Organic Framework.

Detection and sensing of amines through enhanced fluorescence emission are always challenging in aqueous solution. The range of different Lewis basicities, shapes, and sizes as well as the different structural arrangements of amines is responsible for their less specificity in aqueous solution. Here, we have designed a highly fluorescent emissive 2D + 2D → 3D inclined polycatenated NO2-functionalized flexible metal-organic framework (MOF) for selective segregation of electron-rich aromatic primary amines from electron-deficient amines in aqueous solution, showing different emission behaviors. The inclined polycatenated 2D + 2D → 3D MOF having an asymmetric unit {[Cd(dim)(2-nta)(H2O)](H2O)(MeOH)}n (1) has been synthesized by a slow diffusion process and characterized thoroughly by single-crystal and powder X-ray diffraction (PXRD) as well as other physicochemical methods. The desolvated species of 1 (Ref. MOF) is found to be stable and has been characterized by PXRD and adsorption study. The fluorescence profile of the Ref. MOF shows selective enhancement in the presence of electron-rich primary aromatic amines, while the same shows quenching for electron-deficient amines in aqueous solution. The Ref. MOF reported here consists of flexible space between two 2D layers that is responsible for different orientations for different analyte primary aromatic amines (PAAs) with different sizes. The above findings are also supported by time-resolved fluorescence spectroscopy. The respective fluorescence enhancement and quenching have been explained by the interaction between the CB of the host MOF and LUMO of guest amines. Therefore, this work presents an operable method for the sensing of PAAs using a single compound, which is a polycatenated MOF.

Enabling a novel solvent method on Albendazole solid dispersion to improve the in vivo bioavailability

Albendazole, a vital medication endorsed by the World Health Organization for combating parasitic infections, encounters a challenge stemming from its low solubility, significantly impeding absorption and bioavailability. Albendazole has near-insolubility in most organic solvents, so the solid dispersions of albendazole were predominantly using the fusion method. However, the solvent method could offer the advantage of achieving molecular-level mixing homogeneity. In this investigation, we incorporated the pH adjustment to prepare albendazole solid dispersion using a solvent method, which utilizes trace amounts of HCl in methanol, yielding notably enhanced albendazole solubility. Subsequently, carriers such as PEG6000/Poloxamer 188 (PEG: polyethylene glycol) and PVP K30/Poloxamer 188 (PVP: polyvinylpyrrolidone) were employed to create albendazole solid dispersions. Comprehensive characterization through dissolution rate analysis, PXRD (Powder X-ray diffraction), SEM (Scanning electron microscopy), DSC (differential scanning calorimetry), and pharmacokinetic (PK) studies in mice and rats was conducted. The findings indicate that the solid dispersion effectively transforms the crystalline state of albendazole into an amorphous state, resulting in significantly enhanced in vivo absorption and a 5.9-fold increase in exposure. Besides, the exposure increased 1.64 times of commercial albendazole tablets. Notably, PEG6000/Poloxamer 188 and PVP K30/Poloxamer 188 solid dispersions exhibited superior dissolution rates and pharmacokinetic profiles compared to commercially available albendazole tablets.

Enhanced upconversion emission in Nd, Yb, Er and Ho tetra-doped Y2O3 phosphor

Yb3+, Nd3+, Er3+ and Ho3+ tetra ions doped Y2O3 upconversion phosphors have been prepared by the combustion route. Crystalline phase purity and cubic phase of prepared samples have been confirmed from powder X-ray diffraction study. Absorbance of samples over spectral range 200–1100 nm has been measured by diffuse reflectance spectroscopy. All samples exhibit large band gaps. Scanning electron micrograph analysis reveals spherical morphology of particles and sizes around 200 nm. Upconversion emission has been studied under a 980 nm diode laser excitation with 166 mW laser power. The Ho3+, Nd3+ and Yb3+ co-doped Y2O3 phosphor show very high emission intensity of a green band centred at around 550 nm and another moderate intensity red band centred on 667 nm, while reverse is the case for Er3+, Nd3+ and Yb3+ co-doped Y2O3 phosphor. Er3+, Ho3+, Nd3+ and Yb3+ co-doped Y2O3 phosphor show enhanced high emission intensity in both green and red bands. These two bands are not visible in Nd3+ and Yb3+ co-doped Y2O3 phosphor but show weak upconversion emission at 549, 568 and 799 nm. Owing to the high emission intensity of green band, Ho3+, Nd3+ and Yb3+ co-doped Y2O3 phosphor may find potential applications in medical and security, while Er3+, Ho3+, Nd3+ and Yb3+ co-doped phosphor showing enhanced upconversion in green and red bands may find applications in white light generation.

Influence of annealing temperature on microstructure, magnetic and electrical properties of Ce doped cobalt ferrite nanoparticles

Cerium doped cobalt ferrite nanoparticles with chemical formula CoFe1·9Ce0·1O4 were synthesized at different annealing temperatures (600, 700, 800, 900 and 1000C°) via sol-gel auto-combustion method. Thermal analysis for sample annealed at 1000C° was examined through differential scanning calorimetry (DSC) and revealed the presence of exothermic peak at around 500C° attributed to crystallization of prepared nanoferrites. Structural analysis such as phase formation, crystallinity and morphology was investigated by x-ray powder diffraction (XRD) and high resolution transmission electron microscope (HRTEM). XRD study revealed higher dependence of grain size growth with annealing temperatures as compared to lattice parameter. HRTEM investigation confirmed that grains have almost uniform morphology with some agglomeration and confirmed values of lattice parameters and grain sizes calculated from XRD data. Magnetic hysteresis was studied by vibrating sample magnetometer (VSM) at room temperature with an applied field of 20 kOe. The results showed an increase in saturation magnetization and remanent magnetization with increasing of annealing temperature, whereas a decline in coercivity was observed. Distribution of cations at tetrahedral and octahedral sites was investigated using x-ray and magnetic parameters which confirmed the mixed spinel ferrite nature of samples. Dielectric properties were carried out at room temperature in the range 0.1Hz–3.0 MHz. Both dielectric constant and ac conductivity decreased with rising of annealing temperature. Variation of dielectric loss tangent, impedance, electric modulus and relaxation time with temperature were also investigated. The effect of annealing temperature on the structure and its impact on magnetic and dielectric properties has been examined and discussed.

Formulation, optimization and full characterization of mirtazapine loaded aquasomes: a new technique to boost antidepressant effects

Objective The development of Mirtazapine (MRT)-loaded aquasomes by co-precipitation sonication technique to boost the antidepressant potential of MRT. Methodology MRT-loaded aquasomes formulations were prepared using Box–Behnken design to investigate the effect of independent factors including sonication time (X1), sonication temperature (X2), and sugar concentration (X3) on the dependent variables as particle size and drug loading efficiency. The formulation of the optimized formula was verified by Fourier Transform Infrared Spectroscopy (FTIR), Differential Scanning Calorimetry (DSC), and X-ray Powder Diffraction (XRPD). Furthermore, the morphology of the formula was evaluated by Transmission Electron Microscopy (TEM). The optimum MRT- loaded aquasomes was assessed for physiochemical properties, in vitro MRT release and in vivo antidepressant effects in mice model. Results The results revealed that the optimized formula showed a small particle size of 202.7 ± 3.7 nm and a high loading efficiency of 77.65 ± 2.6%. Thermal DSC and XRPD studies demonstrated the amorphous nature of MRT-loaded aquasomes. The in vitro study demonstrated sustained release of F (opt) 88.16% after 8 h, compared with plain MRT release of 63.06% after 1 h. Mice treated with MRT-loaded aquasomes demonstrated reduced immobility time in behavioral analysis to 37% with MRT-loaded aquasomes, while plain MRT reduced it to 55%. Conclusion These results confirmed that the antidepressant effect of MRT was significantly boosted in formulated aquasomes, and thereby they provide a promising carrier nano vesicular system for effective delivery of MRT.

Inhibitory Effect of Alternanthera Sessilis, Cucurbita Maxima and Aerva Lanata on Whewellite Urinary Crystals

Phosphate stones, such as struvite (magnesium ammonium phosphate hexahydrate), brushite (calcium hydrogen phosphate dihydrate), and oxalates like whewellite (calcium oxalate monohydrate) are different kinds of urinary stones. Such kidney stones can be treated with herbs for natural healing and side effects-free results. These urinary crystals are traditionally created in the lab using the gel growth process and a silica gel medium at a specified pH. The inhibitory effects can be analysed by using the extracts of herbal plants. In the present study, ethanol extracts of leaves of Alternanthera sessilis, seeds of Cucurbita maxima and flowers of Aerva lanata are investigated for their inhibitory activity against the whewellite urinary crystals. They are characterized using Fourier transform infrared spectrum and their crystalline nature is examined through powder X-ray diffraction. Asymmetric and symmetric stretching unit of C=O in oxalate appears at 1620 cm-1 and 1400, 1310 cm-1 respectively. The monoclinic crystal system with a space group of P21/n is confirmed from the powder X-ray diffraction studies. The results indicated that among the three ethanol extracts, leaves of Alternanthera sessilis, seeds of Cucurbita maxima and flowers of Aerva lanata- the flowers of Aerva lanata exhibited inhibition towards whewellite crystals. KEYWORDS Extract, flowers, herbs, oxalates, pH, seeds

Formulation Development of Solid Self-Nanoemulsifying Drug Delivery Systems of Quetiapine Fumarate via Hot-Melt Extrusion Technology: Optimization Using Central Composite Design.

Quetiapine fumarate (QTF) was approved for the treatment of schizophrenia and acute manic episodes. QTF can also be used as an adjunctive treatment for major depressive disorders. QTF oral bioavailability is limited due to its poor aqueous solubility and pre-systemic metabolism. The objective of the current investigation was the formulation development and manufacturing of solid self-nanoemulsifying drug delivery system (S-SNEDDS) formulation through a single-step continuous hot-melt extrusion (HME) process to address these drawbacks. In this study, Capmul® MCM, Gelucire® 48/16, and propylene glycol were selected as oil, surfactant, and co-surfactant, respectively, for the preparation of S-SNEDDS. Soluplus® and Klucel™ EF (1:1) were selected as the solid carrier. Response surface methodology in the form of central composite design (CCD) was utilized in the current experimental design to develop the S-SNEDDS formulations via a continuous HME technology. The developed formulations were evaluated for self-emulsifying properties, particle size distribution, thermal behavior, crystallinity, morphology, physicochemical incompatibility, accelerated stability, and in vitro drug release studies. The globule size and emulsification time of the optimized SNEDDS formulation was 92.27 ± 3.4 nm and 3.4 ± 3.38 min. The differential scanning calorimetry (DSC) and powder X-ray diffraction (PXRD) studies revealed the amorphous nature of the drug within the formulation. There were no drug-excipient incompatibilities observed following the Fourier transform infrared (FTIR) spectroscopy. The optimized formulation showed an extended-release profile for 24 h. The optimized formulation was stable for three months (last time-point tested) at 40 °C/75% RH. Therefore, the developed S-SNEDDS formulation could be an effective oral delivery platform for QTF and could lead to better therapeutic outcomes.

Preparation, In Vitro Characterization, and Evaluation of Polymeric pH-Responsive Hydrogels for Controlled Drug Release.

The purpose of the current research is to formulate a smart drug delivery system for solubility enhancement and sustained release of hydrophobic drugs. Drug solubility-related challenges constitute a significant concern for formulation scientists. To address this issue, a recent study focused on developing PEG-g-poly(MAA) copolymeric nanogels to enhance the solubility of olmesartan, a poorly soluble drug. The researchers employed a free radical polymerization technique to formulate these nanogels. Nine formulations were formulated. The newly formulated nanogels underwent comprehensive tests, including physicochemical assessments, dissolution studies, solubility evaluations, toxicity investigations, and stability examinations. Fourier transform infrared (FTIR) investigations confirmed the successful encapsulation of olmesartan within the nanogels, while thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) studies verified their thermal stability. Scanning electron microscopy (SEM) images revealed the presence of pores on the surface of the nanogels, facilitating water penetration and promoting rapid drug release. Moreover, powder X-ray diffraction (PXRD) studies indicated that the prepared nanogels exhibited an amorphous structure. The nanogel carrier system led to a significant enhancement in olmesartan's solubility, achieving a remarkable 12.3-fold increase at pH 1.2 and 13.29-fold rise in phosphate buffer of pH 6.8 (NGP3). Significant swelling was observed at pH 6.8 compared to pH 1.2. Moreover, the formulated nexus is nontoxic and biocompatible and depicts considerable potential for delivery of drugs and protein as well as heat-sensitive active moieties.