Weight Percent Gain Research Articles

Physical Properties of Fast-Growing Wood-Polymer Nano Composite Synthesized through TiO2 Nanoparticle Impregnation.

Mangium (Acacia mangium Willd.) is a fast-growing wood that is widely grown in Indonesia. The impregnation method is needed to improve the qualities of the wood. In this study, TiO2 nanoparticle (79.17 nm) was produced using the hydrothermal method. The purpose of this study was to analyze the effect of TiO2 nanoparticle impregnation on the density and dimensional stability of mangium and the effectiveness of the presence of TiO2 nanoparticle in wood in degrading pollutants. The mangium samples (2 cm × 2 cm × 2 cm) were placed inside impregnation tube. The impregnation solutions included water (untreated), 1% TiO2 nanoparticle, and 5% TiO2 nanoparticles. The samples were analyzed for density, weight percent gain (WPG) dan bulking effect (BE). Samples were also analyzed by X-ray diffraction (XRD) and Fourier-transform infrared spectroscopy (FTIR). TiO2 nanoparticle resulted in an increase in density, WPG, and BE-treated mangium. Based on XRD and FTIR results, TiO2 nanoparticle was successfully impregnated into mangium wood. Scanning electron microscopy–energy-dispersive X-ray spectroscopy analysis indicated that TiO2 nanoparticle covered the surface of the wood cells. The TiO2-impregnated mangium wood has a higher photocatalyst activity than untreated, indicating better protection from UV radiation and pollutants.

IMPREGNATION ON POPLAR WOOD WITH VEGETABLE OILS: EFFECTS ON PHYSICAL MECHANICAL AND DIMENSIONAL STABILITY PROPERTIES

In this study, vegetable oils were selected to modify poplar with vacuum-pressure impregnation technology and the optimum progress was studied.The weight percent gain (WPG), modulus of rupture (MOR), modulus of elasticity (MOE), water uptake rate (WUR), volume swelling rate (VSR) and volume shrinkage rate (VSR') were evaluated. The results showed that the dimensional stability, physical and mechanical properties of treated wood were significantly improved. Scanning electron microscopy (SEM) observations revealed that castor oil was inserted into the interior of the wood through the pores. Vegetable oil modification (castor oil) decreased the intensities of hydroxyl, cellulose and hemicellulose specific peak in theFourier transform infrared spectroscopy (FT-IR) results. The Fourier transform infrared spectroscopy (FT-IR) results showed that castor oil treatment decreased the intensities of hydroxyl, cellulose and hemicellulose specific peak. Ultimately, the optimum process of castor oil treatment was impregnation pressure 1.8 MPa, time 1.0 h andtemperature 85°C based on therange and variance analysis.

Sound Insulation Performance of Furfuryl Alcohol-Modified Poplar Veneer Used in Functional Plywood.

Plywood has poor sound insulation due to its insufficient areal density, which cannot satisfy the demands of an indoor acoustic environment. This report proposed to use furfuryl alcohol to impregnate poplar veneer as a raw material for plywood and explored the sound insulation potential of furfuryl alcohol-modified poplar veneer. The effect of different formulations on the sound insulation performance of modified veneers was discussed, such as furfuryl alcohol concentrations, catalyst categories, and solvent categories. The weight percent gain (WPG) and areal density (AD) were used to evaluate the impregnation effectiveness of furfuryl alcohol modification. The sound insulation was measured by the impedance tube method. The results showed that the WPG of the furfuryl alcohol-modified veneers was evident, and the AD was effectively improved. Furthermore, the average sound insulation of furfuryl alcohol-modified poplar veneer was 25.68~40.10 dB, which increased by 10.8~19.1% compared with that of unmodified veneer. The modified veneer with 50% furfuryl alcohol concentration, taking isopropanol as a solvent, and maleic anhydride as a catalyst, had the optimal sound insulation performance. At the same time, the cell microstructure and chemical components were characterized by scanning electron microscope (SEM), Fourier-transform infrared spectroscopy (FTIR), and Brunauer–Emmett–Teller (BET) theory to explain the sound insulation mechanism further. The results showed that the distortion of cell walls was improved, suggesting a change in the mechanical properties of the cell wall. At the same time, more micropores formed since the filling of furfuryl alcohol resin, yielding a tortuous propagation pathway, so the sound insulation performance improved. Finally, it demonstrated the potential of furfuryl alcohol-modified poplar veneer as raw material to prepare plywood with excellent sound insulation.

Dimensional stabilization of wood by microporous silica aerogel using in-situ polymerization

In this paper, a method for dimensional stabilization of wood through bulk hydrophobization was investigated using a sol–gel process resulting in in-situ formation of microporous SiO2 aerogel. Two different wood species, beech (Fagus sylvatica) and Scots pine (Pinus sylvestris) were investigated. The incorporation of microporous silica aerogel inside the cell wall and lumen was verified by scanning electron microscopy, energy dispersive spectrometry and Fourier-transform infrared spectroscopy. A leaching test using paper as model material proved the bonding of the aerogel to the cellulose component of the cell wall, which indicates a long-lasting effect of the treatment. The modification of wood with silica aerogel significantly improved its hygroscopicity and dimensional stability, decreased the equilibrium moisture content and water uptake beside a low weight percent gain. Permeability was reduced as a result of the silica aerogel deposition in the macro- and micropores of the modified wood. The treatment resulted in an obvious colour change as well.

Manufacturing and Characterization of Modified Wood with In Situ Polymerization and Cross-Linking of Water-Soluble Monomers on Wood Cell Walls.

Fast-growing plantation wood has poor dimensional stability and easily cracks, which limits its application. As wood modification can improve the dimensional stability, strength, and other properties of wood, it has been extensively used. In this study, 2-Hydroxyethyl methacrylate (HEMA) and glyoxal were applied to treat poplar wood (Populus euramevicana cv.I-214) by using vacuum pressure impregnation to improve its dimensional stability. The weight percentage gain (WPG), anti-swelling efficiency (ASE), water absorption rate (WAR), leachability (L), and other properties of modified wood were examined. Results showed that the modifier was diffused into the cell walls and intercellular space and reacted with the wood cell wall after heating to form a stable reticular structure polymer which effectively decreased the hydroxyl content in the wood and blocked the water movement channel; thus, further improving the physical performance of wood. These results were confirmed by scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), and nuclear magnetic resonance (NMR). When the ratio of the modifier was 80:20, the concentration of the modifier was 40%, and the curing temperature was 120 °C, the modified poplar had the best performance, which showed a low WAR (at its lowest 58.39%), a low L (at its lowest 10.44%), and a high ASE (of up to 77.94%).

Resistance of the inner part of oil palm trunk impregnated with aqueous polymer-isocyanate to subterranean termite attack

Isocyanate impregnation was studied relative to the subterranean termite (Coptotermes curvignathus Holmgren) resistance of the inner part of oil palm (Elaeis guineensis Jacq.) trunk. Unproductive oil palm trunk was harvested and divided into top and bottom parts. Samples were isolated from the inner part of the trunk with a size of 2.5 cm x 2.5 cm x 0.5 cm. The samples were impregnated with 10% and 20% aqueous polymer-isocyanate and then heated at 60 °C for 48 h. The specimens were fed to subterranean termites under laboratory conditions. The weight percent gain values were 15.3% to 21.0% and 9.2% to 14.7% for the top and bottom parts, respectively. A higher isocyanate concentration decreased the moisture content and increased the density of inner part of the oil palm trunk. Impregnation with aqueous polymer-isocyanate increased termite mortality at the bottom part and decreased the feeding rate and weight percent loss. Impregnation with 10% and 20% aqueous polymer-isocyanate enhanced the resistance class of the bottom part of the inner part of the oil palm trunk from very poorly resistant (V) to poorly resistant (IV) and moderately resistant (III), respectively, based on the standard adopted.

Effect of Impregnation with a Low-Concentration Furfuryl Alcohol Aqueous Solution on Hygroscopic Properties of Chinese Fir and Poplar Wood

Furfurylation with a low concentration of furfuryl alcohol (FA) promotes the improvement of the properties and the effectiveness of FA on cell–wall action without darkening the furfurylated wood to the point that it affects its applications. In this paper, the effects of furfurylation on the hygroscopicity and water uptake dimensional stability of poplar (Populus sp.) and Chinese fir (Cunninghamia lanceolata) were analyzed. Meanwhile, the distribution of FA resin, the relationship between wood and water, the change in pore size distribution, and the weight percentage gain and cell wall bulking coefficient of wood were also investigated. The results were as follows: (1) A low concentration of FA could better enter the cell walls of the Chinese fir than the poplar, as FA resin was almost cured in the secondary walls, cell corners, and compound middle lamellae when a 10% concentration of FA was applied to the Chinese fir and poplar. When the FA concentration was increased to 30%, there were no significant increases in the amount of FA entering the cell walls and the amounts of FA cured in the cell lumen of the poplar were greater than those of the Chinese fir. Meanwhile, the modification of cell walls was more suitable in poplar than in Chinese fir. (2) The pointed ends of the pit chambers and the pit apertures (800–1000 nm) in the poplar and the small pores of the pit membranes and the pit apertures (1–6 μm) in the Chinese fir were partially deposited by the FA resin, which formed new pores in the size ranges of 80–600 nm and 15–100 nm, respectively. The porosity of the poplar was greater than that of the Chinese fir, and the bulk density of the poplar was less than that of the Chinese fir before and after modification. (3) Furfurylation with a low concentration of FA was able to better reduce the equilibrium moisture content, improve the anti-swelling efficiency, and enhance the dimensional stability of the poplar wood compared to the Chinese fir. Furfurylation effectively reduced water uptake due to the hydrophobic property of the FA resin. The water uptake of the Chinese fir increased by 17%–19% in second cyclic water soaking when treated with FA with various concentrations, which indicated the loss and leaching of FA resin during the test. Low-field NMR was used to demonstrate that the furfurylation not only reduced the amount of water but also affected the combination state of bound and free water with wood. Thus, furfurylation at a low concentration is a feasible method by which to extend applications of furfurylated wood.

Effect of preservative treatment on physical and mechanical properties of bamboo (Gigantochloa scortechinii) strips

Using a vacuum pressure cylinder, Gigantochloa scortechinii was treated with boron and copper chrome boron (CCB) preservative at different concentrations of 2% and 3%. The treatability of untreated and treated bamboo, as well as its physical and mechanical properties, were investigated. Both preservatives showed a high level of penetration into the bamboo strips. Weight percent gain (WPG) and extent of retention of CCB-treated bamboo strips were higher than those of the boron-treated samples. Swelling and shrinkage were proportionately reduced with treatment, with a significant difference between radial and tangential dimensions. When compared to untreated bamboo, treated bamboo showed a greater reduction in radial swelling but a lower reduction in shrinkage. The mechanical properties of untreated and treated samples differed in modulus of elasticity (MOE) and compression. Untreated samples had the highest MOE of 26,100 N.mm-2, while boron and CCB had MOE values of 22,800 and 22,900 N.mm-2, respectively. Copper chrome boron samples had the highest compression value of 86.3 N.mm-2, while the boron and untreated samples had values of 84.0 and 78.3 N.mm-2, respectively.

Properties Enhancement of Oil Palm Trunk Plywood against Decay and Termite for Marine Applications.

Oil palm trunk (OPT) veneers have the potential to be used in the production of plywood for marine applications. However, OPT is not resistant to fungal decay and termites, limiting its use in the production of marine plywood. As a result, in this study, phenolic resin treatment was used to improve the biological durability of OPT and produce marine grade equivalent (MGE) plywood. The OPT veneer was treated with medium molecular weight phenol formaldehyde (MmwPF) resin. The results showed that MmwPF resin with a solid content of 30% resulted in higher weight percent gain and polymer retention. Veneers treated with 30% MmwPF resin were then pressed for more than 10 min at temperatures above 140 °C. Dimensional stability, shear strength, bending strength, fungal decay resistance, and termite resistance were all tested on the plywood produced. The results of this study revealed that MGE plywood has satisfactory bonding quality and excellent biological durability. Good bending strength was recorded for the MGE plywood with modulus of rupture and modulus of elasticity ranged between 31.03 and 38.85 MPa and 4110 and 5120 MPa, respectively. Rubberwood, as a reference sample in this study, is not durable (Class 5) against white rot fungi and is moderately durable (Class III) against subterranean termite attacks. Interestingly, MGE plywood produced in this study was found very durable (Class 1) against white rot fungi. It is also durable (Class II) and very durable (Class I) against termite attacks, depending on the pressing parameters employed. Based on their outstanding bonding quality, bending strength, and biological durability, the study confirmed the feasibility of OPT plywood for marine applications.

Wood Properties of Nine Acetylated Tropical Hardwoods from Fast-Grown Plantations in Costa Rica

The treatment of acetylation on tropical woods is influenced by their different levels of permeability and how these affect the weight percentage gain (WPG) in acetylated wood. The objective of the current study was to identify the effect of acetylation on the thermal stability, color, physical properties, hygroscopic and dimensional stability, wetting rate, and durability of nine tropical species of woods used for the commercial reforestation in Costa Rica. Study results showed that WPG varied from 2.2% to 16.8%. Positive significant correlations were observed between WPG and pre-exponential factors in TGA analysis and two parameters of dimensional and hygroscopic stability, whereas a negative correlation was observed with water absorption. In species with a WPG of over 10% (Vochysia ferruginea, V. guatemalensis, Cordia alliodora, and Enterolobium cyclocarpum) the thermal stability, wetting rate, hygroscopic stability, and resistance to biological attack showed an increase while swelling, and water absorption decreased. For these species, the best behaviors were obtained with an acetylation time of 2.5 hours and WPG values of over 10%. The same properties of wood in species with a WPG under 5% were found to be less affected by the different acetylation times and showed little difference in relation to untreated wood. Finally, the analysis showed that the dimensional stability obtained was attributed to the reduction of the absorptive capacity of the acetylated wood.

Reactivity of Waterlogged Archeological Elm Wood with Organosilicon Compounds Applied as Wood Consolidants: 2D 1H-13C Solution-State NMR Studies.

Some organosilicon compounds, including alkoxysilanes and siloxanes, proved effective in stabilizing the dimensions of waterlogged archaeological wood during drying, which is essential in the conservation process of ancient artifacts. However, it was difficult to determine a strong correlation between the wood stabilizing effect and the properties of organosilicon compounds, such as molecular weight and size, weight percent gain, and the presence of other potentially reactive groups. Therefore, to better understand the mechanism behind the stabilization effectiveness, the reactivity of organosilicons with wood polymers was studied using a 2D 1H–13C solution-state NMR technique. The results showed an extensive modification of lignin through its demethoxylation and decarbonylation and also the absence of the native cellulose anomeric peak in siloxane-treated wood. The most substantial reactivity between wood polymers and organosilicon was observed with the (3-mercaptopropyl)trimethoxysilane treatment, showing complete removal of lignin side chains, the lowest syringyl/guaiacyl ratio, depolymerization of cellulose and xylan, and reactivity with the C6 primary hydroxyls in cellulose. This may explain the outstanding stabilizing effectiveness of this silane and supports the conclusion that extensive chemical interactions are essential in this process. It also indicates the vital role of a mercapto group in wood stabilization by organosilicons. This 2D NMR technique sheds new light on the chemical mechanisms involved in organosilicon consolidation of wood and reveals what chemical characteristics are essential in developing future conservation treatments.

Nanostructural Changes Correlated to Decay Resistance of Chemically Modified Wood Fibers

Reactive chemical modifications have been shown to impart decay resistance to wood. These modifications change hydroxyl availability, water uptake, surface energy, and the nanostructure of wood. Because fungal action occurs on the micro and nano scale, further investigation into the nanostructure may lead to better strategies to prevent fungal decay. The aim of this article is to introduce our findings using small angle neutron scattering (SANS) to probe the effects of chemical modifications on the nanostructure of wood fibers. Southern pine wood fiber samples were chemically modified to various weight percentage gains (WPG) using propylene oxide (PO), butylene oxide (BO), or acetic anhydride (AA). After modification, the samples were water leached for two weeks to remove any unreacted reagents, homopolymers or by-products and then the equilibrium moisture content (EMC) was determined. Laboratory soil-block-decay evaluations against the brown rot fungus Gloeophyllum trabeum were performed to determine weight loss and decay resistance of the modifications. To assist in understanding the mechanism behind fungal decay resistance, SANS was used to study samples that were fully immersed in deuterium oxide (D2O). These measurements revealed that modifying the fibers led to differences in the swollen wood nanostructure compared to unmodified wood fibers. Moreover, the modifications led to differences in the nanoscale features observed in samples that were exposed to brown rot fungal attack compared to unmodified wood fibers and solid wood blocks modified with alkylene oxides.

Development of metallic wood with enhanced physical, mechanical, and thermal conduction properties based on a self-driven penetration mechanism

High-performance wood composite materials have attracted an increasing interest in recent years due to their excellent mechanical and thermal properties obtained by wood metallization. However, the existing methods for wood metallization generally result in structural damage to wood cell walls and large amounts of energy consumption caused by high-pressure treatment. Herein, a high-efficiency, energy-saving, self-driven wood metallization method was proposed for the fabrication of metallic wood based on high-low temperature alternating cycle treatment and the control of the moisture content in wood. The results show that a high weight percent gain of 544.65% was reached for the metallic wood with the dimensions of 20 mm × 20 mm × 20 mm. The density of the metallic wood was about 5.85 times higher than that of the unmodified wood. In addition, the compression strength and thermal conductivity of the metallic wood could be up to 3 times and 10 times higher than those of the unmodified wood, respectively. Interestingly, the penetration effect was immune to the wood sample dimensions applied here. The further mechanism analysis of the penetration of the low melting point alloy into the wood suggest that the vacuum effect in the wood channels caused by the change of water in the wood channels with the temperature difference contributed to providing the driving force and reducing the internal resistance, thus achieving rapid penetration. The modified metallic wood with enhanced physical, mechanical, and thermal properties can be potentially utilized in construction and heat-conductive flooring.

Effect of Acetylation and Accelerated Weathering of Nigerian Grown Rubberwood (Hevea brasiliensis, Müll. Arg.) on Equilibrium Moisture Content and Colour Change

This study was conducted to investigate the effect of acetylation on equilibrium moisture content (EMC) of Nigerian-grown rubberwood and its effect on colour change in exposure of rubberwood to surface degradation through accelerated weathering. The samples were modified to two levels of acetylation, which yielded weight percent gain (WPG) of 7 % and 10 % after 8hr (8-hr Acetyl) and 48hr of acetylation (48-hr Acetyl), respectively. Accelerated weathering of unmodified (Ref) and acetylated wood was done using QUV-Accelerated Weathering Tester for four weeks. The unmodified and acetylated samples (weathered and unweathered) were oven-dried and conditioned in climate rooms at different relative humidity of 50 %, 65 % and 95 %, with samples being moved to each room after 14 days. Results showed that acetylation led to a significant decrease in equilibrium moisture content of rubberwood. After weathering, there was a decrease in EMC of rubberwood due to removal of hemicelluloses alongside the degraded lignin, and a slight increase in EMC of the acetylated wood. In terms of colour change, photo-bleaching of the acetylated samples was higher (10.46 for 48-hr Acetyl) after four weeks of weathering compared to the unmodified samples (6.43). Hence, the outcome of this study has shown that, although acetylation is effective in minimizing moisture ingress into wood, it resulted in photo-bleaching of the weathered samples. Additional surface coating is recommended to serve as a protective layer, preventing partial washing out of the acetyl groups, minimize photo-bleaching during weathering and prolong the aesthetic value of the wood especially in outdoor applications such as wall cladding and façade.

Heat treatment induces chemical changes and silica sol penetration in wood for properties improvement: hydrophobicity, thermal stability, and surface hardness

Thermal modification could act as pretreatment for promoting silica sol impregnation in wood. It could create extra available channels and spaces for silica transportation and deposition owing to the presence of micro-cracks and enlarged pore size. The significant improvements on anti-hygroscopicity, hydrophobicity, and dimensional stability of treated wood were attributed to the degradation of cell wall polymer (hemicellulose, cellulose, and lignin) and filling effect of silica in wood. The synergistic effect contained the reduction on –OH concentration owing to thermal degradation, and consumption of –OH groups via the interaction (Si–O–Si cross linked networks and Si–O–C covalent bonds) between silica and wood matrix. Furthermore, the degradation of cell wall polymers resulted in the increase of crystallinity in wood. However, the crystallinity turned to decrease due to the amorphous silica impregnation. The silica impregnation could compensate the mass loss caused by thermal degradation, leading to various weight percentage gains (WPGs) that depended on treatment temperature. Moreover, owing to the coverage and penetration of mineral silica in wood, acting as a thermal barrier, the thermal stability and surface hardness of treated wood improved prominently.

Effects of Low-Energy-Density Microwave Treatment on Graphene/Polyvinyl Alcohol-Modified Poplar Veneer

The combination of natural wood and graphene can provide a new type of material with excellent mechanical properties and thermal conductivity. However, it is difficult for graphene to uniformly penetrate the wood due to the anisotropy of natural wood and the agglomeration of graphene. In this work, poplar veneer was treated with low-energy-density microwave to expand the entry pathways for the graphene steering liquid. The porosity, weight percent gain, and chromatic aberration were used to examine the impact of the microwave time and power. We tested the mechanical properties, thermal conductivity of the graphene/polyvinyl alcohol-modified poplar veneer to evaluate its properties. At the same time, SEM, XRD, and FT-IR were used to characterize its physical and chemical structure. The results showed that low-energy-density microwave treatment increased the weight percentage gain (WPG) and porosity without affecting the mechanical properties of the poplar veneer. The graphene-modified poplar veneer with the optimal overall performance was obtained by microwave treatment at 100% microwave power for 50 s. Indeed, the micro-characterization also revealed that the microwave treatment mostly attacked the wood rays but had little effect on the materialized structure. Therefore, low-energy-density microwave treatment could be an energy-saving and efficient way to improve graphene-impregnated veneers.

Investigations of the Chemical Distribution in Sorbitol and Citric Acid (SorCA) Treated Wood—Development of a Quality Control Method on the Basis of Electromagnetic Radiation

Recent studies showed treatments with sorbitol and citric acid (SorCA) to significantly improve the dimensional stability and biological durability of wood. The industrialization of this process requires a quality control (QC) method to determine if the fixated chemicals are homogenously distributed within the piece of wood, which is essential for uniform material performance. Therefore, the objective of this work was to evaluate the use of common electromagnetic radiation-based methods to determine the degree of modification in SorCA-treated wood. Both Fourier transform infrared (FTIR) spectroscopy and near-infrared (NIR) spectroscopy have been used to create rough calibrations for the weight percent gain (WPG) prediction models. The FTIR measurements resulted in a high linear correlation between the band area ratio (BAR) and the WPG (R2 = 0.93). Additionally, a partial least square (PLS) regression of NIR spectroscopic data resulted in a model with a high prediction power (R2 = 0.83). Furthermore, X-ray density profiling emerged as a simple alternative for the QC by showing a gradient of modification chemicals inside the sample and differences in chemical uptake between earlywood and latewood. Overall, it can be concluded that the results from FTIR, NIR and X-ray densitometry can serve as indicators of impregnation chemical distribution in SorCA-modified wood.

EFFECTS OF MODIFICATION WITH MELAMINE–UREA–FORMALDEHYDE RESIN ON THE PROPERTIES OF UREA PRETREATED EUCALYPTUS

Eucalyptus urophylla was treated with melamine-urea-formaldehyde resin (MUF) after pretreatment with urea solution. The properties of the wood were then determined.The weight percent gain (WPG) and, antiswelling efficiencies (ASE) of the wood treated with urea+MUF were 14% and, 45% higher than those of untreated wood, respectively. The water absorption (WA) of the wood treated with urea+MUF was decreased approximately 50% lower than that of the untreated wood. However, the mechanical properties of the wood treated with urea+MUF were weakened due to the destruction of the structure of wood. An X-ray photoelectron spectroscopy (XPS) analysis revealed that the atomic concentration ratio of O/C was increased. The ratio of C1 was decreased as the lignin and extractives contents were decreased, while theratios of C2 and C3 were increased. The urea solution pretreatment was conducive to theimpregnation of wood functional modifiers.

Small Angle Neutron Scattering Reveals Wood Nanostructural Features in Decay Resistant Chemically Modified Wood

While it is known that modifying the hydroxyls in wood can improve the decay resistance; what is often missing in the literature is whether these modifications alter wood nanostructure, and how these changes correlate to the improved decay resistance. Here, we used small angle neutron scattering (SANS) to probe the effects of alkylene oxide modifications on wood nanostructure. Southern pine wood samples were chemically modified to various weight percentage gains (WPG) using four different alkylene oxides: propylene oxide (PO), butylene oxide (BO), epichlorohydrin (EpH), and epoxybutene (EpB). After modification, the samples were water leached for 2 weeks to remove any unreacted reagents or homopolymers and then equilibrium moisture content (EMC) was determined at 90% relative humidity (RH) and 27°C. Laboratory soil block decay evaluations against the brown rot fungus Gloeophyllum trabeum were performed to determine weight loss and biological efficacy of the modifications. To assist in understanding the mechanism, SANS was used to study samples that were fully immersed in deuterium oxide (D2O). These measurements revealed that the modifications altered the water distribution inside the cell wall, and the most effective modifications reduced the microfibril swelling and preserved the microfibril structure even after being subject to 12 weeks of brown rot exposure.

Evaluation of natural weathering and thermal degradation behavior of furfurylated bamboo strips at different weight percent gain

Evaluation of natural weathering and thermal degradation behavior of furfurylated bamboo strips at different weight percent gain