Wear In Total Hip Replacements Research Articles

Finite element analysis of polyethylene wear in total hip replacement: A literature review.

Evaluation and prediction of wear play a key role in product design and material selection of total hip replacements, because wear debris is one of the main causes of loosening and failure. Multifactorial clinical or laboratory studies are high cost and require unfeasible timeframes for implant development. Simulation using finite element methods is an efficient and inexpensive alternative to predict wear and pre-screen various parameters. This article presents a comprehensive literature review of the state-of-the-art finite element modelling techniques that have been applied to evaluate wear in polyethylene hip replacement components. A number of knowledge gaps are identified including the need to develop appropriate wear coefficients and the analysis of daily living activities.

Does vitamin E highly-crosslinked polyethylene convey an advantage in primary total hip replacement? A systematic review and meta-analysis.

Vitamin E highly cross-linked polyethylene (HXLPE) was developed to reduce wear in total hip replacement (THR). This formal systematic review and meta-analysis aimed to provide independent synthesis of wear characteristics of Vitamin E treated HXLPE compared to HXPLE/UHMWPE. Secondary outcome measures were differences in revision rates and functional scores. We performed a formal systematic review as per PRISMA guidelines; literature searches were conducted on 14 November 2017 (MEDLINE, Embase on Ovid, and the Cochrane Library). We included randomised controlled trials, analyses of joint registries, and case-controlled studies of primary THR comparing cups with a vitamin E HXLPE bearing with bearing surfaces made from other types of polyethylene. Initial screening was performed by 2 independent assessors; disagreement resolved in discussion with a third reviewer. Studies were evaluated using the Cochrane risk of bias tool. Data extraction permitted meta-analysis. 372 studies were identified on initial screening, 5 studies met the eligibility criteria. There was no significant heterogeneity between studies. There was variable risk of bias. At a mean of 35 (range 20-60) months, Vitamin E HXLPE had significant advantages over highly cross-linked polyethylene with regards total femoral head penetration (p = 0.004). Given the RSA measurement errors this may not be clinically significant.There were neither significant differences in revision rates nor Harris Hip Scores (p = 0.06). At a minimum of 3 years follow-up there was reduced total femoral head penetration for vitamin E HXLPE over HXLPE. This bearing surface does not, as yet, have clinically significant advantages in terms of revision rates or patient function over HXLPE.

Prosthetic liner wear in total hip replacement: a longitudinal 13-year study with computed tomography

This case report follows a woman who had a total hip replacement in 1992 when she was 45 years old. Six serial computed tomography (CT) examinations over a period of 13 years provided information that allowed her revision surgery to be limited to liner replacement as opposed to replacement of the entire prosthesis. Additionally, they provided data that ruled out the presence of osteolysis and indeed none was found at surgery. In 2004, when the first CT was performed, the 3D distance the femoral head had penetrated into the cup was determined to be 2.6 mm. By 2017, femoral head penetration had progressed to 5.0 mm. The extracted liner showed wear at the thinnest part to be 5.5 mm, as measured with a micrometer. The use of modern CT techniques can identify problems, while still correctable without major surgery. Furthermore, the ability of CT to assess the direction of wear revealed that the liner wear changed from the cranial to dorsal direction.

Three-dimensional friction measurement during hip simulation

ObjectivesWear of total hip replacements has been the focus of many studies. However, frictional effects, such as high loading on intramodular connections or the interface to the bone, as well as friction associated squeaking have recently increased interest about the amount of friction that is generated during daily activities. The aim of this study was thus to establish and validate a three-dimensional friction setup under standardized conditions.Materials and methodsA standard hip simulator was modified to allow for high precision measurements of small frictional effects in the hip during three-dimensional hip articulation. The setup was verified by an ideal hydrostatic bearing and validated with a static-load physical pendulum and an extension-flexion rotation with a dynamic load profile. Additionally, a pendulum model was proposed for screening measurement of frictional effects based on the damping behavior of the angular oscillation without the need for any force/moment transducer. Finally, three-dimensional friction measurements have been realized for ceramic-on-polyethylene bearings of three different sizes (28, 36 and 40 mm).ResultsA precision of less than 0.2 Nm during three-dimensional friction measurements was reported, while increased frictional torque (resultant as well as taper torque) was measured for larger head diameters. These effects have been confirmed by simple pendulum tests and the theoretical model. A comparison with current literature about friction measurements is presented.ConclusionsThis investigation of friction is able to provide more information about a field that has been dominated by the reduction of wear. It should be considered in future pre-clinical testing protocols given by international organizations of standardization.

Prediction of Polyethylene Wear Rates from Gait Biomechanics and Implant Positioning in Total Hip Replacement.

Patient-specific gait and surgical variables are known to play an important role in wear of total hip replacements (THR). However a rigorous model, capable of predicting wear rate based on a comprehensive set of subject-specific gait and component-positioning variables, has to our knowledge, not been reported. (1) Are there any differences between patients with high, moderate, and low wear rate in terms of gait and/or positioning variables? (2) Can we design a model to predict the wear rate based on gait and positioning variables? (3) Which group of wear factors (gait or positioning) contributes more to the wear rate? Data on patients undergoing primary unilateral THR who performed a postoperative gait test were screened for inclusion. We included patients with a 28-mm metal head and a hip cup made of noncrosslinked polyethylene (GUR 415 and 1050) from a single manufacturer (Zimmer, Inc). To calculate wear rates from radiographs, inclusion called for patients with a series of standing radiographs taken more than 1 year after surgery. Further, exclusion criteria were established to obtain reasonably reliable and homogeneous wear readings. Seventy-three (83% of included) patients met all criteria, and the final dataset consisted of 43 males and 30 females, 69 ± 10 years old, with a BMI of 27.3 ± 4.7 kg/m2. Wear rates of these patients were determined based on the relative displacement of the femoral head with regard to the cup using a validated computer-assisted X-ray wear-analysis suite. Three groups with low (< 0.1 mm/year), moderate (0.1 to 0.2 mm/year), and high (> 0.2 mm/year) wear were established. Wear prediction followed a two-step process: (1) linear discriminant analysis to estimate the level of wear (low, moderate, or high), and (2) multiple linear and nonlinear regression modeling to predict the exact wear rate from gait and implant-positioning variables for each level of wear. There were no group differences for positioning and gait suggesting that wear differences are caused by a combination of wear factors rather than single variables. The linear discriminant analysis model correctly predicted the level of wear in 80% of patients with low wear, 87% of subjects with moderate wear, and 73% of subjects with high wear based on a combination of gait and positioning variables. For every wear level, multiple linear and nonlinear regression showed strong associations between gait biomechanics, implant positioning, and wear rate, with the nonlinear model having a higher prediction accuracy. Flexion-extension ROM and hip moments in the sagittal and transverse planes explained 42% to 60% of wear rate while positioning factors, (such as cup medialization and cup inclination angle) explained only 10% to 33%. Patient-specific wear rates are associated with patients' gait patterns. Gait pattern has a greater influence on wear than component positioning for traditional metal-on-polyethylene bearings. The consideration of individual gait bears potential to further reduce implant wear in THR. In the future, a predictive wear model may identify individual, modifiable wear factors for modern materials.

Development and validation of an acoustic emission device to measure wear in total hip replacements in-vitro and in-vivo

Abstract An increasing demand for total joint replacement surgeries has provided a great need for more effective diagnostic procedures for monitoring and identifying wear, loosening, and other failure modes in total joint replacement implants. Significant recent research attention has been focussed on the contributing factors to wear and audible squeaking of total hip replacement (THR) implants and in particular those with hard-on-hard bearing combinations. An acoustic emission (AE) monitoring prototype diagnostic device has been developed for the assessment of implant wear and stability in THR patients. Implant vibrations have been recorded by AE monitoring during in-vivo patient testing from 90 patients with a range of age, implant type, and implant conditions. A number of these patients have gone on to have subsequent revision surgery and in-vitro testing of implant components previously tested in-vivo has been possible. The AE monitoring device has been able to detect a significant number of acoustic events, including audible squeaking, from both the in-vivo and in-vitro environments. This manuscript focusses on the data from five patients with ceramic-on-ceramic bearing interfaces for whom significant audible squeaking occurred and both in-vivo and in-vitro AE monitoring was undertaken. Preliminary results from the in-vitro monitoring data show audible squeaking AEs have similar characteristics to in-vivo audible squeaking AEs and both have primary frequencies in the 1–4 kHz range. This study has indicated that the AE device shows promise as a potential diagnostic tool for assessing the condition of THR implants. In addition, the in-vitro technique was shown to be useful at providing further insight into the mechanisms of wear and acoustic emissions of THR implants. The study also provides important initial results for the assessment of the AE device as a diagnostic tool through the unique contribution of the testing and analysis of the same implant components in both in-vivo and in-vitro environments.

Measurement outcomes from hip simulators.

Simulation of wear in total hip replacements has been recognised as an important factor in determining the likelihood of clinical success. However, accurate measurement of wear can be problematic with factors such as number and morphology of wear particles produced as well as ion release proving more important in the biological response to hip replacements than wear volume or wear rate alone. In this study, hard-on-hard (CoCr alloy, AgCrN coating) and hard-on-soft (CoCr alloy and CrN coating on vitamin E blended highly cross-linked polyethylene) bearing combinations were tested in an orbital hip simulator under standard and some adverse conditions. Gravimetric wear rates were determined for all bearings, with cobalt and where applicable, silver release determined throughout testing. Isolation of wear particles from the lubricating fluid was used to determine the influence of different bearing combinations and wear conditions on particle morphology. It was found that cobalt and silver could be measured in the lubricating fluid even when volumetric wear was not detectable. In hard-on-hard bearings, Pearson's correlation of 0.98 was established between metal release into the lubricating fluid and wear volume. In hard-on-soft bearings, coating the head did not influence the polyethylene wear rates measured under standard conditions but did influence the cobalt release; the diameter influenced both polyethylene wear and cobalt release, and the introduction of adverse testing generated smaller polyethylene particles. While hip simulators can be useful to assess the wear performance of a new material or design, measurement of other outcomes may yield greater insight into the clinical behaviour of the bearings in vivo.

The effect of different assembly loads on taper junction fretting wear in total hip replacements

Variability in the magnitude of the impaction force applied by surgeons to assemble a hip prosthetic head to a femoral stem could be a cause of increased wear in taper junctions. This study investigates the effect of varying the magnitude of the assembly force on fretting wear at the taper over a 10 year period using a 3D finite element model and wear algorithm. It is demonstrated that an increase in assembly force results in a reduction in fretting wear and it is recommended that surgeons should apply an impact force of at least 4kN to minimise wear rates. The wear patterns and wear rates presented are comparable with observation and measurement of those seen in retrieved prostheses.

Low wear, high stability - promises of success in a moderately cross-linked cup?

Cross-linking has proven effective in reducing polyethylene wear in total hip replacements. However, increasing the amount of cross-links will impair other mechanical properties of the polyethylene. The optimal threshold of crosslinking has still not been established. This led to the development of a moderately cross-linked (5 Mrad) cemented cup in which wear and stability is yet to be determined. A total of, 70 hips were included in this case series on the cemented Marathon® cup. Mean age of the patients was 78 years (SD 15). We measured wear and migration by radiostereometry at 3, 12 and 24 months. The proximal wear rate estimate between 3 to 24 months was 0.036 mm/year, and a total proximal wear estimate at 2 years of 0.11 mm (95% CI 0.09-0.14). Translations and rotations along the 3 cardinal axes were all at or below the precision limit, and less than what is believed to be predictive of later loosening, namely 0.2-1 mm for proximal migration. The cups remained stable after the initial "bedding in" that occurred during the first 3 months. Our results indicate that moderate cross-linking (5Mrad) yields low wear and high stability in this specific acetabular cup, comparable to other cups with higher cross-linking.

Effect of cup inclination on predicted contact stress-induced volumetric wear in total hip replacement

In order to increase the lifetime of the total hip endoprosthesis, it is necessary to understand mechanisms leading to its failure. In this work, we address volumetric wear of the artificial cup, in particular the effect of its inclination with respect to the vertical. Volumetric wear was calculated by using mathematical models for resultant hip force, contact stress and penetration of the prosthesis head into the cup. Relevance of the dependence of volumetric wear on inclination of the cup (its abduction angle ϑA) was assessed by the results of 95 hips with implanted endoprosthesis. Geometrical parameters obtained from standard antero-posterior radiographs were taken as input data. Volumetric wear decreases with increasing cup abduction angle ϑA. The correlation within the population of 95 hips was statistically significant (P = 0.006). Large cup abduction angle minimises predicted volumetric wear but may increase the risk for dislocation of the artificial head from the cup in the one-legged stance. Cup abduction angle and direction of the resultant hip force may compensate each other to achieve optimal position of the cup with respect to wear and dislocation in the one-legged stance for a particular patient.

Alumina-on-alumina hip implants

Alumina-alumina bearings are among the most resistant to wear in total hip replacement. Examination of their surfaces is one way of comparing damage caused by wear of hip joints simulated in vitro to that seen in explanted bearings. The aim of this study was to determine whether second-generation ceramic bearings exhibited a better pattern of wear than those reported in the literature for first-generation bearings. We considered both macro- and microscopic findings. We found that long-term alumina wear in association with a loose acetabular component could be categorised into three groups. Of 20 specimens, four had 'low wear', eight 'crescent wear' and eight 'severe wear', which was characterised by a change in the physical shape of the bearing and a loss of volume. This suggests that the wear in alumina-alumina bearings in association with a loose acetabular component may be variable in pattern, and may explain, in part, why the wear of a ceramic head in vivo may be greater than that seen after in vitro testing.

Grundlagen und neue Konzepte in der computernavigierten Hüftendoprothetik

Combined component placement of cup and stem is closely correlated to stability, functionality and wear in total hip replacement (THA). Computer-navigated orthopedic surgery offers a reliable control method for a complex three-dimensional situation. Imageless navigation systems without the need of preoperative or intraoperative image acquisition and exposure to radiation have been proven to increase the accuracy of positioning the acetabular component and measure intraoperative leg length and offset changes precisely. A new development in this field is the noninvasive external femoral reference marker array system in conjunction with an imageless measurement technique. The future generation of imageless navigation systems will switch from simple measurement tasks to an integral part of the surgical process in navigated THA. The aim will be to find an optimized complementary component orientation with improved postoperative functionality and optimized range of motion without impingement.

Sandwich type ceramic liner fracture rate with the Atlas III™ socket: A study of 144 primary total hip replacements at a mean 74 months’ follow-up

Ceramic friction bearings have been proposed as a means of reducing wear in total hip replacement (THR). A "sandwich" composite concept including a ceramic bearing surface has been proposed as simplifying the modularity while matching metal-back cups with a polyethylene liner. It is not precisely known how frequently abnormal noise would occur during functioning of this type of implant, which moreover entails a risk of ceramic liner fracture. Results with sandwich type ceramic liners are comparable to those with polyethylene liners, without risk of side effects (noise, fracture). Clinical and radiological results of 144 cementless Atlas III™ cups containing a 28mm-diameter polyethylene-ceramic sandwich type liner coupled to a ceramic Biolox Forte™ head were retrospectively analyzed at a mean 74 months' follow-up. Mean patient age was 59.4 years. Twelve patients were lost to follow-up. Femoral components comprised 61 ESOP™ anatomic stems and 71 BHS™ Corail stems. The radiologic study used Imagika™ software. Global function scores were satisfactory: PMA score, 17.2±1.2 (range, 9 to 18); global Harris score, 93.6±3.1 (49 to 100). Global survivorship was 91.6% (95% CI: 86.34-96.9). Radioclinical analysis found seven liner fractures (5.3%) at a mean 32 months; all were non-traumatic and asymptomatic. Clinical risk factors for liner fracture were overweight, advanced age, dislocation, prosthetic impingement, increased postoperative offset was a radiologic risk factor. Despite these satisfactory radioclinical results, matching those for metal-backed implants containing a polyethylene liner, close surveillance is mandatory with this type of composite implant. The high fracture rate with ceramic-polyethylene sandwich type liners and relative lack of symptoms warrant caution in their use. Level IV, retrospective or historic series.

The contribution of the micropores in bone cement surface to generation of femoral stem wear in total hip replacement

Although cemented total hip replacement has long been recognized as a situation that can lead to wear, the wear generated on the femoral stem has not been well documented, especially with regard to how this wear is initiated and propagated. This present work aimed to further investigate this issue based on a comprehensive study on surface morphology of the femoral stem and the bone cement, which were collected from seven in vitro wear simulations. It was shown that the wear locations on the stem surface compared well with the results of retrieval studies, and the boundaries of the worn areas matched well the edges of the micropores present in the bone cement surface. This indicated that the micropores could potentially contribute to the generation of femoral stem wear. In addition, metallic debris was detected around the micropores from the simulation with increased loading cycles. However, no evidence of macro-cracks was observed across the cement mantle in spite of the presence of micro-cracks initiated at the edge of the micropores. This study demonstrated a possible cause for progression of femoral stem wear and it may have an important bearing on the long term durability of cemented hip prosthesis.

Polyethylene wear in total hip replacement with zirconia femoral head

Polyethylene wear in total hip replacement with zirconia femoral head

The determination of linear and angular penetration of the femoral head into the acetabular component as an assessment of wear in total hip replacement

We have compared four computer-assisted methods to measure penetration of the femoral head into the acetabular component in total hip replacement. These were the Martell Hip Analysis suite 7.14, Rogan HyperOrtho, Rogan View Pro-X and Roman v1.70. The images used for the investigation comprised 24 anteroposterior digital radiographs and 24 conventional acetate radiographs which were scanned to provide digital images. These radiographs were acquired from 24 patients with an uncemented total hip replacement with a follow-up of approximately eight years (mean 8.1; 6.3 to 9.1). Each image was measured twice by two blinded observers. The mean annual rates of penetration of the femoral head measured in the eight-year single image analysis were: Martell, 0.24 (SD 0.19); HyperOrtho, 0.12 (SD 0.08); View Pro-X, 0.12 (SD 0.06); Roman, 0.12 (SD 0.07). In paired analysis of the six-month and eight-year radiographs: Martell, 0.35 (SD 0.22); HyperOrtho, 0.15 (SD 0.13); View Pro-X, 0.11 (SD 0.06); Roman, 0.11 (SD 0.07). The intra- and inter-observer variability for the paired analysis was best for View Pro-X and Roman software, with intraclass correlations of 0.97, 0.87 and 0.96, 0.87, respectively, and worst for HyperOrtho and Martell, with intraclass correlations of 0.46, 0.13 and 0.33, 0.39, respectively. The Roman method proved the most precise and the most easy to use in clinical practice and the software is available free of charge. The Martell method showed the lowest precision, indicating a problem with its edge detection algorithm on digital images.

Wear of sequentially enhanced 9‐Mrad polyethylene in 10 million cycle knee simulation study

Highly crosslinked polyethylene (HXPE) has been shown to be effective in reducing wear in total hip replacements. HXPE has not found widespread use in TKR, because the crosslinking inevitably leads to reductions in critical properties such as toughness and fatigue strength. Sequentially enhanced crosslinking (SXPE) have been suggested for improved wear resistance for tibial inserts with maintenance of mechanical properties and anticipated high oxidation resistance superior to conventional polyethylene (XLPE). We compared the wear of SXPE (9Mrad) to XLPE inserts (3Mrad) to 10 million cycles. Triathlon femoral condyles were identical in both. This is the first wear study of SXPE inserts. According to the power law relating irradiation dose to wear of XLPE inserts, wear of 9 Mrad inserts should be reduced by 70% compared to 3Mrad controls. The wear rates of the SXPE inserts were reduced by 86% at 10 million cycles duration, somewhat greater than predicted. The one prior investigation by the manufacturer reported a 79% wear reduction for SXPE compared to controls in a 5 million cycle simulator study in knee design and test parameters. There were important differences between the two studies. Nevertheless there clearly appeared to be a major benefit for sequentially enhanced polyethylene in tibial inserts. This combined wear reduction of 80-85% with improved oxidation resistance and retention of mechanical properties may prove beneficial for active patients who may otherwise risk high wear rates over many years of use.

Association of Third Body Embedment with Rim Damage in Retrieved Acetabular Liners

Third-body effects are a major cause of the substantial variability of wear in total hip replacements. One potential mechanism by which third-body debris can access wear-critical central regions of closely conforming metal-on-polyethylene bearing couples is by fluid convection during incidents of subluxation accompanying neck-on-liner impingement. To provide evidence for this premise, we determined the association of severity of liner rim indentation damage (indicative of impingement frequency/vigor) and the presence of embedded third-body debris in 194 implants retrieved at revision. Rim damage was graded using the five-point Hospital for Special Surgery scale. Particle embedment was assessed both manually and by means of an image analysis computer program that detected the composition, size, and location of each particle. Sixty-eight percent of the cups showed rim indentation damage. We found an association between severity of rim damage and presence of embedded debris. There was substantial nonuniformity of the spatial distribution of the embedded debris, with the predominance of embedded debris at intermediate latitudes. These findings support the premise of convection of debris-laden joint fluid during lever-out subluxation as a mechanism for wear-consequential third-body particles to gain access to highly loaded regions of the bearing surface, thus potentiating increased wear.

The effect of geometry and abduction angle on the stresses in cemented UHMWPE acetabular cups – finite element simulations and experimental tests

BackgroundContact pressure of UHMWPE acetabular cup has been shown to correlate with wear in total hip replacement (THR). The aim of the present study was to test the hypotheses that the cup geometry, abduction angle, thickness and clearance can modify the stresses in cemented polyethylene cups.MethodsAcetabular cups with different geometries (Link®: IP and Lubinus eccentric) were tested cyclically in a simulator at 45° and 60° abduction angles. Finite element (FE) meshes were generated and two additional designs were reconstructed to test the effects of the cup clearance and thickness. Contact pressures at cup-head and cup-cement interfaces were calculated as a function of loading force at 45°, 60° and 80° abduction angles.ResultsAt the cup-head interface, IP experienced lower contact pressures than the Lubinus eccentric at low loading forces. However, at higher loading forces, much higher contact pressures were produced on the surface of IP cup. An increase in the abduction angle increased contact pressure in the IP model, but this did not occur to any major extent with the Lubinus eccentric model. At the cup-cement interface, IP experienced lower contact pressures. Increased clearance between cup and head increased contact pressure both at cup-head and cup-cement interfaces, whereas a decreased thickness of polyethylene layer increased contact pressure only at the cup-cement interface. FE results were consistent with experimental tests and acetabular cup deformations.ConclusionFE analyses showed that geometrical design, thickness and abduction angle of the acetabular cup, as well as the clearance between the cup and head do change significantly the mechanical stresses experienced by a cemented UHMWPE acetabular cup. These factors should be taken into account in future development of THR prostheses. FE technique is a useful tool with which to address these issues.

Validation of two and three-dimensional radiographic techniques for measuring polyethylene wear after total hip arthroplasty.

Three-dimensional radiographic techniques have been developed to estimate in vivo polyethylene wear of total hip replacements. We are not aware of any published study examining the accuracy of these in vivo methods. Our objective was to validate two radiographic techniques by comparing their results with those obtained directly from retrieved specimens. A coordinate measuring machine was used to probe the interior bearing surface of seventeen acetabular liners that had been retrieved at revision surgery. Solid models were created to determine volumetric polyethylene loss and linear depth and direction of wear. Two in vivo radiographic techniques (PolyWare and the Martell Hip Analysis Suite) were used to calculate two-dimensional linear, three-dimensional linear, and volumetric wear. The radiographic analysis was done independently, and the results were compared with the known values of polyethylene wear derived with use of the coordinate measuring machine. Correlation coefficients comparing the values for two-dimensional and three-dimensional linear wear and volumetric wear derived with the PolyWare radiographic technique with the values derived with the coordinate measuring machine were r(2) = 0.78, r(2) = 0.75, and r(2) = 0.91, respectively (all p < 0.001), and the correlation coefficients comparing the values derived with the Martell Hip Analysis Suite radiographic technique with those derived with the coordinate measuring machine were r(2) = 0.80, r(2) = 0.84, and r(2) = 0.91, respectively (p < 0.001). The average absolute difference between the radiographic estimates and the results derived with the coordinate measuring machine was approximately 19% (range, 13% to 24%). There was good agreement between the wear estimates made with both in vivo techniques and the measurements of the retrieved polyethylene liners made with the coordinate measuring machine. Two-dimensional wear analysis (based on anteroposterior radiographs) accounted for most of the polyethylene wear, while one technique of three-dimensional wear analysis (PolyWare) demonstrated some additional wear in the lateral plane.