Water Flow Research Articles

OPTIMIZATION OF MIB-02 WELL BY CONVERTING THE ACTIVATION MODE USING PROSPER SOFTWARE

Mibale oil field considered a mature oil field, located offshore in the coastal basin of the DR Congo and discovered in 1973, has seen an evolution in its production since it began operation in 1976, starting from an initial rate of 10,000 BOPD with 3 producing wells to the current production of 5,905 BOPD from 14 wells. In 2021, the field had 393 MMstb of oil reserves in the reservoir. A thorough study of the production system was carried out, focusing on the five best producing wells, including well MIB-02. Despite traversing layers of the reservoir with high oil potential, the well is underperforming with a respective flow rate of 351 BOPD and a 60% WOR using an electric submersible pump. Following this low production, various studies were conducted, including the study on converting the activation method by proceeding with nodal analysis technique. The use of nodal analysis proved crucial in identifying the shortcomings of the production system, combining field history with analysis of production, well test, pressure, and completion data. The IPM Prosper software enabled a thorough analysis, revealing that MIB-02 had a production potential greater than its current performance. This performance was revealed after evaluation and interpretation of IPR, VLP curves and sensitivities of variables such as water cut and pressure at the first node. After interpreting these curves, the MIB-02 well had the production capacity of 4100.62 BOPD and 12463.9 BWPD. By converting the submersible electric pump activation mode to gas-lift and exploring various scenarios, production was improved with an oil flow rate of 1244.9 BOPD, water flow of 2539 BWPD, to a gas flow of 0.37346 MMscf/day and 67.1% water cut. Despite these improvements, excessive water production remains a challenge while also highlighting the complexity of the production system and the limitations of the analysis technique. Therefore, further studies can be envisaged by modeling and simulating the reservoir, considering well interventions and quantifying the remaining reserves today. This more comprehensive approach will enable a clearer vision and help decide the best optimization strategies for the Mibale field production system.

Effects of interlayer spacing and applied pressure on the lanthanide transport in MoS2-based two-dimensional channels

ABSTRACT Rare-earth elements (REEs) are critical to modern industry but difficult to separate due to their subtle and monotonic changes in physicochemical properties. MoS2-based two-dimensional (2D) materials offer novel opportunities for enhancing REE separation, exhibiting a distinct volcano-shaped transport performance distribution that peaks at Sm3+. However, the specific contributions of thermodynamic and kinetic factors to ion transport within 2D confinement remain unclear. In this study, we conducted a series of non-equilibrium all-atom molecular dynamics (MD) simulations to explore the effects of interlayer spacing and external pressure on the transport of lanthanide ions in Å-scale acetate functionalized 2D MoS2 (MoS2-COOH) channels. We examined ion entry and permeation rates, water flux, dehydration, and binding modes. The simulation results reveal that the transport trends of lanthanide ions are jointly driven by the dehydration degree and the relative-binding strengths of ions to water and to the acetate within the 2D channels. Notably, the dehydration pattern of lanthanide ions during permeation is closely linked to kinetic factors. Overall, this study provides a detailed atomistic understanding of the mechanisms underlying lanthanide ion transport under confinement. These findings point to the significant potential for tuning confinement and chemical functionalization within Å-scale channels for more efficient REE separation.

Time series prediction model using LSTM-Transformer neural network for mine water inflow

Mine flooding accidents have occurred frequently in recent years, and the predicting of mine water inflow is one of the most crucial flood warning indicators. Further, the mine water inflow is characterized by non-linearity and instability, making it difficult to predict. Accordingly, we propose a time series prediction model based on the fusion of the Transformer algorithm, which relies on self-attention, and the LSTM algorithm, which captures long-term dependencies. In this paper, Baotailong mine water inflow in Heilongjiang Province is used as sample data, and the sample data is divided into different ratios of the training set and test set in order to obtain optimal prediction results. In this study, we demonstrate that the LSTM-Transformer model exhibits the highest training accuracy when the ratio is 7:3. To improve the efficiency of search, the combination of random search and Bayesian optimization is used to determine the network model parameters and regularization parameters. Finally, in order to verify the accuracy of the LSTM-Transformer model, the LSTM-Transformer model is compared with LSTM, CNN, Transformer and CNN–LSTM models. The results prove that LSTM-Transformer has the highest prediction accuracy, and all the indicators of its model are well improved.

Tunable Wettability of a Dual-Faced Covalent Organic Framework Membrane for Enhanced Water Filtration.

Membrane technology plays a central role in advancing separation processes, particularly in water treatment. Covalent organic frameworks (COFs) have transformative potential in this field due to their adjustable structures and robustness. However, conventional COF membrane synthesis methods are often associated with challenges, such as time-consuming processes and limited control over surface properties. Our study demonstrates a rapid, microwave-assisted method to synthesize self-standing COF membranes within minutes. This approach allows control over the wettability of the surface and achieves superhydrophilic and near-hydrophobic properties. A thorough characterization of the membrane allows a detailed analysis of the membrane properties and the difference in wettability between its two faces. Microwave activation accelerates the self-assembly of the COF nanosheets, whereby the thickness of the membrane can be controlled by adjusting the time of the reaction. The superhydrophilic vapor side of the membrane results from -NH2 reactions with acetic acid, while the nearly hydrophobic dioxane side has terminal aldehyde groups. Leveraging the superhydrophilic face, water filtration at high water flux, complete oil removal, increased rejection with anionic dye size, and resistance to organic fouling were achieved. The TTA-DFP-COF membrane opens new avenues for research to address the urgent need for water purification, distinguished by its synthesis speed, simplicity, and superior separation capabilities.

Learning obstacle avoidance and predation in complex reef environments with deep reinforcement learning

The reef ecosystem plays a vital role as a habitat for fish species with limited swimming capabilities, serving not only as a sanctuary and food source but also influencing their behavioral tendencies. Understanding the intricate mechanism through which fish adeptly navigate the moving targets within reef environments within complex water flow, all while evading obstacles and maintaining stable postures, has remained a challenging and prominent subject in the realms of fish behavior, ecology, and biomimetics alike. An integrated simulation framework is used to investigate fish predation problems within intricate environments, combining deep reinforcement learning algorithms (DRL) with high-precision fluid-structure interaction numerical methods-immersed boundary lattice Boltzmann method (lB-LBM). The Soft Actor-Critic (SAC) algorithm is used to improve the intelligent fish's capacity for random exploration, tackling the multi-objective sparse reward challenge inherent in real-world scenarios. Additionally, a reward shaping method tailored to its action purposes has been developed, capable of capturing outcomes and trend characteristics effectively. The convergence and robustness advantages of the method elucidated in this paper are showcased through two case studies: one addressing fish capturing randomly moving targets in hydrostatic flow field, and the other focusing on fish counter-current foraging in reef environments to capture drifting food. A comprehensive analysis was conducted of the influence and significance of various reward types on the decision-making processes of intelligent fish within intricate environments.

Fish communicate with water flow to enhance a school's social network.

Schooling fish rely on a social network created through signaling between its members to interact with their environment. Previous studies have established that vision is necessary for schooling and that flow sensing by the lateral-line system may aid in a school's cohesion. However, it remains unclear to what extent flow provides a channel of communication between schooling fish. Based on kinematic measurements of the speed and heading of schooling tetras (Petitella rhodostoma), we found that compromising the lateral line by chemical treatment reduced the mutual information between individuals by ∼13%. This relatively small reduction in pairwise communication propagated through schools of varying size to reduce the degree and connectivity of the social network by more than half. Treated schools additionally showed more than twice the spatial heterogeneity of fish with unaltered flow sensing. These effects were much more substantial than the changes that we measured in the nearest-neighbor distance, speed, and intermittency of individual fish by compromising flow sensing. Therefore, flow serves as a valuable supplement to visual communication in a manner that is revealed through a school's network properties.

Water fluxes and energy partitioning over a Larix principis-rupprechtii plantation forest in a dryland mountain ecosystem, Northwest China

Plantations make up a sizable component of forest ecosystems in China's drylands and play an important role controlling the energy balance and water cycle. However, there is limited knowledge regarding the exchange of water and energy in dryland plantations, particularly those located within the intricate and unique environments of dryland mountain regions. The focus of this study was the investigation of a Larix principis−rupprechtii plantation within a dryland mountain ecosystem located in Northwest China. The eddy covariance method was employed to calculate the water and energy fluxes, while the thermal dissipation probe (TDP) method was utilized to measure forest overstory transpiration (T) from 2018 to 2021. The links between energy allocation and various components in water flux were investigated, as well as the variable dynamics of water and energy flux and their relationship with environmental conditions. The findings demonstrated that the annual mean cumulative evapotranspiration (ET) was about 510 mm, accounting for over 82.8 % of the precipitation, which was mainly from soil evaporation and understory transpiration, rather than overstory transpiration (T). The average value of T/ET was 0.25 for the growing season, and surface conductance (Gs) was always higher than canopy conductance (Gc) on both daily and monthly scales. The evaporative fraction (EF) and Priestley-Taylor model coefficient (α) in the growing season were significantly higher than those in the non-growing season, and α>1 from June to September, indicating that the ecosystem in the study area had sufficient water supply. Furthermore, during the growing season, the ratio of latent heat flux (LE) to net radiation (Rn) was larger than that in the non-growing season, while the proportion of sensible heat flux (H) was opposite, and soil heat flux (G) accounted for the smallest proportion of net radiation. This study provides valuable insights into the energy fluxes and water fluxes within the ecosystem of dryland mountain plantations, and it serves as a guide for choosing afforestation tree species in the future.

Mathematical modeling of intracellular osmolarity and cell volume stabilization: The Donnan effect and ion transport.

The presence of impermeant molecules within a cell can lead to an increase in cell volume through the influx of water driven by osmosis. This phenomenon is known as the Donnan (or Gibbs-Donnan) effect. Animal cells actively transport ions to counteract the Donnan effect and regulate their volume, actively pumping Na+ out and K+ into their cytosol using the Na+/K+ ATPase (NKA) pump. The pump-leak equations (PLEs) are a system of algebraic-differential equations to model the membrane potential, ion (Na+, K+, and Cl-), and water flux across the cell membrane, which provide insight into how the combination of passive ions fluxes and active transport contribute to stabilizing cell volume. Our broad objective is to provide analytical insight into the PLEs through three lines of investigation: (1) we show that the provision of impermeant extracellular molecules can stabilize the volume of a passive cell; (2) we demonstrate that the mathematical form of the NKA pump is not as important as the stoichiometry for cell stabilization; and (3) we investigate the interaction between the NKA pump and cation-chloride co-transporters (CCCs) on cell stabilization, showing that NCC can destabilize a cell while NKCC and KCC can stabilize it. We incorporate extracellular impermeant molecules, NKA pump, and CCCs into the PLEs and derive the exact formula for the steady states in terms of all the parameters. This analytical expression enables us to easily explore the effect of each of the system parameters on the existence and stability of the steady states.

Construction of low-resistance nano-transport channels with UiO-66-(NH2)2 “transmembrane” in polyamide layer structure for efficient nanofiltration

Metal-organic frameworks (MOFs) is always a research hotspot as the modifier for fabrication of thin-film nanocomposite (TFN) membrane due to their excellent chemical tunability and suitable pore size. However, the traditional strategy for the involvement of MOFs into interfacial polymerization (IP) process has its limitations, as the addition of MOFs only serve to modulate the structure of the polyamide (PA) layer and to optimize the transport path of water molecules, rather than play an important role in selectively sieving solutes. To solve the problem that MOF embedded under the PA layer cannot directly participate in solute sieving, this study designed a “transmembrane” structure of MOF in the PA layer. Here, the feasibility of 1,3,5-Benzenetricarbonyl chloride modified UiO-66-(NH2)2 was verified based on Gibbs free energy calculations. By adding chlorinated UiO-66-(NH2)2 nanomaterials in the dual IP process, a high-throughput nanofiltration membrane was innovatively constructed. In contrast to conventional thin-film composite membrane prepared by only one IP process, the sieving mechanism no longer relied solely on the free volume of the PA chain segments. Instead, it was determined by the combination of the pore channels of UiO-66-(NH2)2 and the matrix gaps. Based on density functional theory (DFT), the calculated diffusion energy barriers of H2O and Na2SO4 in UiO-66-(NH2)2 and PA matrices reveal the reasons for the improvement of water flux and changes in retention rate of TFN membranes. In addition, the gap size between PA-MOFs was determined by comparing the solvation and de-solvation structures of dye molecules. This work provides a new theoretical basis for explaining the changes in the separation performance of TFN membranes, and offers new ideas for the development of novel TFN membrane structures.

Properties and Model of Pore-Scale Methane Displacing Water in Hydrate-Bearing Sediments

The flow characteristics of methane and water in sedimentary layers are important factors that affect the beneficial exploitation of marine hydrates. To study the influencing factors of methane drive-off water processes in porous media, we constructed nonhomogeneous geometric models using MATLAB 2020a random distribution functions. We developed a mathematical model of gas–water two-phase flow based on the Navier–Stokes equation. The gas-driven water processes in porous media were described using the level-set method and solved through the finite element method. We investigated the effects of the nonhomogeneous structure of pore media, wettability, and repulsion rate on gas-driven water channeling. The nonhomogeneity of the pore medium is the most critical factor influencing the flow. The size of the throat within the hydrophilic environment determines the level of difficulty of gas-driven water flow. In regions with a high concentration of narrow passages, the formation of extensive air-locked areas is more likely, leading to a decrease in the efficiency of the flow channel. In the gas–water drive process, water saturation changes over time according to a negative exponential function relationship. The more hydrophilic the pore medium, the more difficult the gas-phase drive becomes, and this correlation is particularly noticeable at higher drive rates. The significant pressure differentials caused by the high drive-off velocities lead to quicker methane breakthroughs. Instantaneous flow rates at narrow throats can be up to two orders of magnitude higher than average. Additionally, there is a susceptibility to vortex flow in the area where the throat connects to the orifice. The results of this study can enhance our understanding of gas–water two-phase flow in porous media and help commercialize the exploitation of clean energy in the deep ocean.

On the possible use of hydraulic force to assist with building the step pyramid of saqqara.

The Step Pyramid of Djoser in Saqqara, Egypt, is considered the oldest of the seven monumental pyramids built about 4,500 years ago. From transdisciplinary analysis, it was discovered that a hydraulic lift may have been used to build the pyramid. Based on our mapping of the nearby watersheds, we show that one of the unexplained massive Saqqara structures, the Gisr el-Mudir enclosure, has the features of a check dam with the intent to trap sediment and water. The topography beyond the dam suggests a possible ephemeral lake west of the Djoser complex and water flow inside the 'Dry Moat' surrounding it. In the southern section of the moat, we show that the monumental linear rock-cut structure consisting of successive, deep compartments combines the technical requirements of a water treatment facility: a settling basin, a retention basin, and a purification system. Together, the Gisr el-Mudir and the Dry Moat's inner south section work as a unified hydraulic system that improves water quality and regulates flow for practical purposes and human needs. Finally, we identified that the Step Pyramid's internal architecture is consistent with a hydraulic elevation mechanism never reported before. The ancient architects may have raised the stones from the pyramid centre in a volcano fashion using the sediment-free water from the Dry Moat's south section. Ancient Egyptians are famous for their pioneering and mastery of hydraulics through canals for irrigation purposes and barges to transport huge stones. This work opens a new line of research: the use of hydraulic force to erect the massive structures built by Pharaohs.

Scan-to-HBIM-to-VR: An Integrated Approach for the Documentation of an Industrial Archaeology Building

In this paper, we propose a comprehensive and optimised workflow for the documentation and the future maintenance and management of a historical building, integrating the state of the art of different techniques, in the challenging context of industrial archaeology. This approach has been applied to the hydraulic work of the “Sostegno del Battiferro” in Bologna, Italy, an example of built industrial heritage whose construction began in 1439 and remains in active use nowadays to control the Navile canal water flow rate. The initial step was the definition of a 3D topographic frame, including geodetic measurements, which served as a reference for the complete 3D survey integrating Terrestrial Laser Scanning (TLS), Structured Light Projection scanning, and the photogrammetric processing of Unmanned Aircraft System (UAS) imagery through a Structure from Motion (SfM) approach. The resulting 3D point cloud has supported as-built parametric modelling (Scan-to-BIM) with the consequent extraction of plans and sections. Finally, the Heritage/Historic Building Information Modelling (HBIM) model generated was rendered and tested for a VR-based immersive experience. Building Information Modelling (BIM) and virtual reality (VR) applications were tested as a support for the management of the building, the maintenance of the hydraulic system, and the training of qualified technicians. In addition, considering the historical value of the surveyed building, the methodology was also applied for dissemination purposes.

Traditional Tolak Bala Ceremony in Tanah Bara Village, Aceh Singkil from an Islamic Law Perspective

Long before Islam came, local culture and beliefs of Animism and Dynamism were very close to the community. It was from here that the belief that disaster would occur because of something or a matter came into existence. Tolak bala in the big Indonesian dictionary is defined as an action to reject disaster; an effort to avoid danger; a series of activities carried out by a group of people to hold a kenduri tolak bala. Everyone certainly longs for safety and happiness, so that if a disaster threatens them, they try to ward it off. Islamic law has stipulated that only Allah is the source of salvation, a Muslim must believe that only Allah controls all good and harm, both those that have not yet befallen and those that have befallen. As in surah az-zumar verse 38; in other letters such as surah al-Baqarah verse 45 also emphasizes human dependence on Allah. This research was conducted in Tanah Bara village, Gunung Meriah District, Aceh Singkil Regency using a descriptive analysis method. The practice of tolak bala in Tanah Bara village on every Wednesday at the end of the month of Syafar. Various series are carried out such as, hajat prayer, dhikr and prayer to ward off disaster, bathing to ward off disaster using KASE and smearing betel water on the forehead of family members. There is no practice of ward off disaster in Tanah Bara Village that performs offerings such as throwing food into the river for offerings. The practice of ward off disaster as has been briefly described, is carried out only as an effort to keep away from danger. The practice of ward off disaster in Tanah Bara Village is legitimated by Islamic law, because it still reflects the spirit of Islamic law, meaning that it is permitted in Islamic law for the practice of ward off disaster in Tanah Bara Village. In the practice of ward off disaster that is carried out, there are no acts of idolatry committed, such as throwing offerings into the river, or throwing food with the aim of offerings. Only the essence of the practice of ward off disaster after using KASE, then diving by realizing it like the flow of water with the KASE, then all diseases disappear. This is the point of the problem of the practice of warding off disaster that the author wants to examine further to obtain legal legitimacy, whether it is permissible or not.

Variation of nitrate sources affected by precipitation with different intensities in groundwater in the piedmont plain area of alluvial-pluvial fan

A substantial reservoir of nitrogen (N) in soil poses a threat to the quality and safety of shallow groundwater, especially under extreme precipitation that hastens nitrogen leaching into groundwater. However, the specific impact of varying precipitation intensities on the concentration and sources of nitrate (NO3−) in groundwater across diverse hydrogeological zones and land uses remains unclear. This study aims to elucidate the fluctuations in NO3− concentration, sources, and controlling factors in shallow groundwater under different intensities of precipitation (extreme heavy precipitation and continuous heavy precipitation) in a typical alluvial-pluvial fan of the North China Plain by using stable isotopes (δ2H–H2O, δ18O–H2O, δ15N–NO3-, δ18O–NO3-), hydrochemical analyses and the SIAR model. Affected by extreme heavy precipitation the depleted isotopes of δ2H–H2O and δ18O–H2O in groundwater of the entire area suggested the rapid recharge of fast flow by precipitation. The enriched isotopes of δ2H–H2O and δ18O–H2O of north part in alluvial fan after continuous heavy precipitation showed the recharge of translatory flow of soil water. NO3−concentrations increased to 78.9 mg/L after extreme heavy precipitation and increased to 105.3 mg/L after continuous heavy precipitation when compared to those in normal year (56.8 mg/L) of north part of the alluvial fan. However, NO3− concentrations had slight variation after continuous heavy precipitation of south part of the fan due to the deep vadose zone. The contribution ratio of sources of NO3− in groundwater by using SIAR analysis revealed manure & sewage (MS) as the primary NO3− source (accounting for 59.7–78.1%) before extreme heavy precipitation, chemical fertilizer (CF) making a minor contribution (6.9–17.3%). Different precipitation events and land use types lead to changes in NO3− sources. Affected by extreme heavy precipitation, the contribution of MS decreased while CF increased, particularly in vegetables (26.2–28.1%) and farmland (29.2–34.7%). After continuous heavy precipitation, MS increased again, particularly in vegetables (50.0%) and farmlands (20.4–66.4%), with CF either increasing or remaining steady. This indicated that continuous heavy precipitation accelerated the leaching of nitrogen (organic manure application) stored in deep soil to groundwater and it has a larger influence on the increasing of NO3− concentrations of groundwater than extreme heavy precipitation which carried nitrogen (chemical fertilizer application) in shallow soil to groundwater by fast flow. These findings underscore the importance of considering soil chemical N stores and their implications for groundwater contamination mitigation under future extreme climate scenarios, particularly in agricultural management practices.

The role of aquaporins in osmotic cell lysis induced by Bacillus thuringiensis Cry1Ac toxin in Helicoverpa armigera

The insecticidal crystalline (Cry) and vegetative insecticidal (Vip) proteins derived from Bacillus thuringiensis (Bt) are used globally to manage insect pests, including the cotton bollworm, Helicoverpa armigera, one of the world's most damaging agricultural pests. Cry proteins bind to the ATP-binding cassette transporter C2 (ABCC2) receptor on the membrane surface of larval midgut cells, resulting in Cry toxin pores, and ultimately leading to cell swelling and/or lysis. Insect aquaporin (AQP) proteins within the membranes of larval midgut cells are proposed to allow the rapid influx of water into enterocytes following the osmotic imbalance triggered by the formation of Cry toxin pores. Here, we examined the involvement of H. armigera AQPs in Cry1Ac-induced osmotic cell swelling. We identified and characterized eight H. armigera AQPs and demonstrated that five are functional water channel proteins. Three of these (HaDrip1, HaPrip, and HaEglp1) were found to be expressed in the larval midgut. Xenopus laevis oocytes co-expressing the known Cry1Ac receptor HaABCC2 and each of the three HaAQPs displayed abnormal morphology and were lysed following exposure to Cry1Ac, suggesting a rapid influx of water was induced after Cry1Ac pore formation. In contrast, oocytes producing either HaABCC2 or HaAQP alone failed to swell or lyse after treatment with Cry1Ac, implying that both Cry1Ac pore formation and HaAQP function are needed for osmotic cell swelling. However, CRISPR/Cas9-mediated knockout of any one of the three HaAQP genes failed to cause significant changes in susceptibility to the Bt toxins Cry1Ac, Cry2Ab, or Vip3Aa. Our findings suggest that the multiple HaAQPs produced in larval midgut cells compensate for each other in allowing for the rapid influx of water in H. armigera midgut cells following Cry toxin pore formation, and that mutations affecting a single HaAQP are unlikely to confer resistance to Bt proteins.

Superoleophobic polyethylene glycol grafted graphene oxide/polyamide 6 nanofibrous composite membrane for highly efficient separation of oil/water emulsion

Graphene oxide (GO) has been applied for membrane-based oil/water emulsion separation processes due to its ease of functionalization, substantial surface area, and abundant hydrophilic hydroxyl and carboxyl functional groups. In this study, the dispersion of GO in polyamide 6 (PA6) was improved through grafting of GO with polyethylene glycol (PEG). The prepared GO-PEG was integrated into PA6 nanofibers at different loading levels and the oil/water emulsion separation of the resulting PA6/GO-PEG membranes was compared as a function of GO-PEG content. The homogeneous dispersion of GO-PEG at a 2 wt% loading level within PA6 nanofibers (designated as PA6/GO-PEG2) resulted in a nanofibrous composite membrane that exhibited exceptional mechanical strength (approximately 16.29 MPa), and remarkable hydrophilic properties (water contact angle of 12.30°). Moreover, a remarkable underwater superoleophobicity was exhibited by PA6/GO-PEG2 and provided an underwater oil contact angle of 150.41°. Notably, the optimal characteristics were showcased by the PA6/GO-PEG2 nanofibrous membrane, offering an impressive water flux rate of 813 L/m2h and an outstanding oil rejection efficiency of 99.26 % when subjected to an oil/water emulsion under a pressure of 1 bar. Furthermore, robust antifouling properties were displayed by PA6/GO-PEG2, in which 95.69 % of the water flux rate was maintained and reached 778 L/m2h, and excellent oil rejection efficiency remained at 98.59 % even after 15 cycles of oil/water separation. These results highlight the potential of the PA6/GO-PEG2 nanofibrous membrane as a highly promising candidate for practical applications in oil/water separation, owing to its superior performance and enduring antifouling characteristics.

Numerical modeling and validation of dike-induced water flow dynamics using OpenFOAM

ABSTRACT The basic purpose of the present research is to numerically elucidate the flow around a single dike in four different geometric configurations (CN: no cylinders, C5: 5 cylinders, C10: 10 cylinders, C15: 15 cylinders), under conditions of a constant flow rate and subcritical flow. This involved substituting the impermeable dike with varying numbers of piles to validate the observed experimental flow patterns, particularly the conditions leading to reverse flow formation. OpenFOAM, an open-source algorithm, was utilized for the simulation, incorporating the volume of fluid (VOF) method. Accurately depicting the reverse flow formation with minimal numerical diffusion, a strategy involving multizone meshing and the application of mesh refinement zones was utilized. These refinements were particularly focused on the section between 1.8 m and 2.2 m within the numerical domain. The water surface profile in front section of the dike and the averaged velocity at five different locations, which were then compared with the numerical results. The numerically predicted streamwise velocity showed a percentage error ranging between 0.5% and 4.5%. The numerical results from this study are pivotal in dike design, aiming to mitigate accelerated wear during flood events and to protect both the dike head and the adjacent bank from high energy flow failures.

Sustainable wastewater recovery system employing geothermal energy – Performance and feasibility study

In this study, a sustainable wastewater recovery system employing geothermal energy has been proposed. The efficiency of the suggested sustainable system has been simulated using heat transfer. Then, component-wise validation has been carried out with the existing data available in the literature wherever applicable and estimated an error of ± 8 %. The proposed sustainable system’s parametric and performance analyses have employed the developed vapor. From the parametric study, it is observed that hot spring temperatures have a significant influence on sustainable systems. Further, through performance investigation, it is understood that low dam/river/sea water temperatures and enhancing the water condenser effectiveness and flow rate ratio simultaneously improve the system performance. For different climatic regions of India, explored the feasible geothermal hotspots near dams/rivers/seawater and analyzed that among the hot and dry, hot and humid, composite and cold regions, the proposed sustainable system is best suitable at a composite region with a maximum possible water extraction/freshwater generation rate of 0.78 L/h for the given specifications and operating range. Moreover, it is assessed that hot spring temperature is the deciding factor for sustainable system performance in different climatic regions. Further, the current study can be used as a reference for understanding the phenomenon of potential geothermal hotspots for wastewater recovery in various climatic areas

Effect of the surface form of the herringbone aluminum plate in a plate heat exchanger on the boiling heat transfer performance of ammonia

In this study, ammonia boiling heat transfer coefficient and the overall heat transfer were measured in a plate evaporator for an ocean thermal energy conversion (OTEC) system using aluminum plates. The OTEC system used ammonia as the working and a plate heat exchanger (PHE) that combined titanium plates. In this study, we used an anodized aluminum herringbone plate with two chevron angles of 45 and 60° installed in a PHE and measured the boiling heat transfer coefficients of ammonia and overall heat transfer coefficients for both plates to compare their heat transfer performances. The experimental conditions included a hot water flow rate of 1 – 12 L/min, a working fluid mass flux of 7 – 30 kg/m2s, a hot water inlet temperature of 30 – 40 °C, and a system pressure of 700 kPa.It was observed that anodized aluminum can be used as a heat-transfer plate for the PHE. In addition, the maximum overall heat transfer coefficient of chevron angle of 45° was 4 kW/m2K, and that of 60° was 3.5 kW/m2K, respectively. The maximum ammonia boiling heat transfer coefficient of 45° was 12.5 kW/m2K, and that of 60° was 13 kW/m2K, respectively. The heat transfer coefficient values are similar. Additionally, the correlation between the nondimensional heat transfer and the Lockhart-Martinelli parameter of aluminum plates was also clarified for comparison with the previous ammonia plate heat transfer in a flat plate. By comparing the correlation equations, the aluminum plate exhibited a value twice that of the flat plate.

Examination of static fission properties of 236\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$^{236}$$\\end{document}U and 233\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$^{233}$$\\end{document}Th using Cassinian oval parametrization within the macroscopic–microscopic approach

We have conducted a thorough analysis of the potential energy surfaces (PES) in 236\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$^{236}$$\\end{document}U and 233\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$^{233}$$\\end{document}Th using the Cassini-ovals parameterization within the macro–micro approach. We employed the state-of-the-art immersion water flow (IWF) method to study the saddles on four-dimensional energy grids encompassing reflection-asymmetric shapes. For 233\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$^{233}$$\\end{document}Th, we computed the adiabatic potential energy surfaces by minimizing configurations with one blocked neutron within ten levels below and above the Fermi level. Our results show satisfactory agreement with empirical and experimental estimates for both nuclei, specifically regarding the first and second fission barriers. This suggests that our method holds promise in efficiently describing non-compact shapes while reducing the dimensionality of the space without sacrificing accuracy. Interestingly, employing Cassinian oval parameterization fails to reveal a pronounced, hyper-deformed third minimum in the potential energy landscape. Instead, only a shallow third minimum is observed for 233\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$^{233}$$\\end{document}Th, while in 236\\documentclass[12pt]{minimal} \\usepackage{amsmath} \\usepackage{wasysym} \\usepackage{amsfonts} \\usepackage{amssymb} \\usepackage{amsbsy} \\usepackage{mathrsfs} \\usepackage{upgreek} \\setlength{\\oddsidemargin}{-69pt} \\begin{document}$$^{236}$$\\end{document}U, this minimum ultimately vanishes. This finding holds significant importance when considering the modeling of fission cross-sections.