Strength Values Research Articles

Examining the Workability, Mechanical, and Thermal Characteristics of Eco-Friendly, Structural Self-Compacting Lightweight Concrete Enhanced with Fly Ash and Silica Fume.

This study compares the workability, mechanical, and thermal characteristics of structural self-compacting lightweight concrete (SCLWC) formulations using pumice aggregate (PA), expanded perlite aggregate (EPA), fly ash (FA), and silica fume (SF). FA and SF were used as partial substitutes for cement at a 10% ratio in various mixes, impacting different aspects: According to the obtained results, FA enhanced the workability but SF reduced it, while SF improved the compressive and splitting tensile strengths more than FA. EPA, used as a fine aggregate alongside PA, decreased the workability, compressive strength, and splitting tensile strength compared to the control mix (K0). The thermal properties were altered by FA and SF similarly, while EPA notably reduced the thermal conductivity coefficients. The thermal conductivity coefficients (TCCs) of the K0-K4 SCLWC mixtures ranged from 0.275 to 0.364 W/mK. K0 had a TCC of 0.364 W/mK. With 10% FA, K1 achieved 0.305 W/mK; K2 with 10% SF reached 0.325 W/mK. K3 and K4, using EPA instead of PA, showed significantly lower TCC values: 0.275 W/mK and 0.289 W/mK, respectively. FA and SF improved the thermal conductivity compared to K0, while EPA further reduced the TCC values in K3 and K4 compared to K1 and K2. The compressive strength (CS) values of the K0-K4 SCLWC mixtures at 7 and 28 days reveal notable trends. Using 10% FA in K1 decreased the CS at both 7 days (12.16 MPa) and 28 days (22.36 MPa), attributed to FA's gradual pozzolanic activity. Conversely, K2 with SF showed increased CS at 7 days (17.88 MPa) and 28 days (29.89 MPa) due to SF's rapid pozzolanic activity. Incorporating EPA into K3 and K4 reduced the CS values compared to PA, indicating EPA's lower strength contribution due to its porous structure.

The Effect of Stacking Sequence and Ply Orientation with Central Hole on Tensile Behavior of Glass Fiber-polyester Composite

An experimental investigation was carried out to study the effect of circular cross-holes on the failure behavior of unidirectional glass fiber reinforced with unsaturated polyester resin composites, varying cross-ply laminates that were subjected to axial tensile load. This paper deals with the effects of the circular notch and the number of plies on nominal tensile and net tensile strengths. Tensile strengths were investigated for composites with cross-ply([0/90]. [90°/0°/90°] and [0°/90°/0°].90°), orientation and varying the laminate layers with a central hole, and effects of volume fraction and number of ply on mechanical properties for un-notched (smooth) and notched specimens were also studied. The results showed that increasing the number of plies has a marginal effect on tensile strength values. The fraction of volume has significant effects and for increasing the number of plies about 9% decreases in nominal tensile strength and about 11% decrease in the net tensile strength was observed. The same results were obtained with finite element analysis.

A 6-minute protocol, combining mental imagery practices and breathing exercises, promotes hand-grip strength in firefighters: a series of "N-of-1" trials.

To carry out their victim rescue and fire-fighting missions, firefighters perform high levels of physical exertion and among them strenuous muscular activity. A specific mental preparation protocol that could induce better strength performance throughout their 24-hour schedule is a major issue for firefighters. This case report aims to examine whether a 6-minute Intervention combining mental imagery practices and breathing exercises, specifically designed to be used while travelling between the fire station and the mission site, would be able to promote maximum strength performance. A series of three Single Case Experimental Designs (SCED) was conducted in single blind design to investigate the effects of repeated challenge-withdrawals between the Intervention and the Baseline on the maximum voluntary isometric contraction (MVIC) strength of the hand-grip. Data analyses revealed that 62.5% to 100% of the hand-grip strength values during the Intervention periods were greater than or equal to the maximum data point recorded in the Baseline periods. The effect sizes of these highlighted increases of the hand-grip strength performance revealed by the percentage of non-overlapping data (PND) were 75% i.e., moderately effective on average. Such a "psyching-up" practice before an upcoming muscular activity can promote muscular strength in firefighters. These results have led French firefighter departments to integrate the teaching of these practices into the initial instruction of firefighters, and remains to be confirmed by a randomised control trial.

ZrO2 and ZnO nanoparticles effect on setting time, microhardness, and compressive strength of calcium-enriched-mixture cement

Aim: Calcium-enriched mixture (CEM) cement is an endodontic biomaterial; however, enhancing its physical/mechanical properties remains a challenge. This in vitro study investigates the influence of zirconium oxide (ZrO2) and zinc oxide (ZnO) nanoparticles on the setting time, microhardness, and compressive strength of CEM cement. Methods: Four different groups of CEM cement were prepared: a control group without nanoparticles, two groups with ZrO2 or ZnO, and a group with a combination of nanoparticles. The nanoparticles were added to the powder in predetermined concentrations. The setting time was evaluated using the Gilmore needle method, while microhardness and compressive strength were determined using Vickers hardness and a universal testing machine, respectively. Results: The incorporation of ZnO slightly reduced the setting time, while the addition of ZrO2 significantly prolonged it compared to the control group. Interestingly, the combination of both nanoparticles exhibited a setting time comparable to that of the control group. Regarding the microhardness and compressive strength, both ZrO2 and ZnO significantly improved these properties compared to the control group. The combination of both nanoparticles showed the highest microhardness and compressive strength values among all groups. Conclusions: The addition of nanoparticles to CEM cement effectively modifies its physical and mechanical properties. The optimal combination of these nanoparticles can potentially achieve an improved balance between setting time and enhanced mechanical performance.

Effects of external verbal cueing on countermovement rebound jump performance

ABSTRACT This study examined the effects of three external verbal cues on countermovement rebound jump (CMRJ) performance. Twenty-five recreational athletes completed nine jumps with distinct height, velocity and combined cue focus. A general linear model analysis of variance was used to evaluate systematic bias between conditions (p < 0.05). The height and velocity cues significantly altered jump height and contact times in both jumps during the CMRJ, respectively (p ≤ 0.002). The combined cue significantly reduced contact time while increasing leg stiffness compared to the height cue (p ≤ 0.038). It also increased jump height compared to the velocity cue (p ≤ 0.005) in both jumps, resulting in the highest explosive power and reactive strength values among all conditions. Furthermore, the combined cue enhanced the positive ankle contribution compared to the height cue (p = 0.020) and increased positive hip and negative knee joint work compared to the velocity cue (p ≤ 0.040) in the second jump of the CMRJ. These findings advise practitioners to use the height cue to maximise jump height, the velocity cue to minimise contact times and the combined cue to maximise explosive power and reactive strength.

An Approach to Improve Specimen Processing for the Flexural Strength Testing of Zirconia.

Measuring the flexural strength of restorative materials such as zirconia is crucial for providing proper indications for clinical applications and predicting performance. Great variations in specimen preparation for flexural strength measurements exist among laboratories. The aim was to evaluate how the processing method, surface treatment, and test method of the specimens affect the flexural strength of zirconia. Zirconia specimens (VITA YZ HT) (n = 270) were processed using CAD/CAM or were conventionally milled with three different surface treatments (machined, ground, polished) and were measured with three-point bending (non-chamfered/chamfered) or biaxial flexural strength test. Weibull statistics were conducted. The mean flexural strength values ranged from 612 MPa (conventional, machined, three-point bending non-chamfered) to 1143 MPa (CAD/CAM, polished, biaxial flexural strength). The highest reliability is achieved when specimens are prepared using thoroughly controllable processing with CAD/CAM and subsequently polished. Higher strength values are achieved with the biaxial flexural strength test method because the stress concentration in relation to the effective volume is smaller. Polishing reduces surface microcracks and therefore increases the strength values.

SUSTAINABILITY THROUGH TEXTILES RECYCLING: YARN REUSE, ENVIRONMENTAL AND HUMAN HEALTH IMPACT

For the sake of achieving the goals of economic growth and welfare increase, world resources are consumed recklessly and cause the generation of very high amounts of waste. This imbalance, consisting of production and consumption phases, has caused the ecosystem to be negatively affected. Although the waste recycling sector is an important sector in Turkey, additional studies are needed to ensure social awareness on waste management, research and development studies, and conversion of textile waste into high value-added products. A significant part of the waste in Turkey is used in yarn production. In this study; A research was conducted on the recycling processes of cotton yarn waste in a business for sustainability. Breaking strength values of yarns containing 10-50% waste in 3 different yarn counts, namely Ne 10, Ne 20 and Ne 30, were estimated by fuzzy logic modeling and the effects of textile waste on the environment and human health were examined.

Validity and reliability of the modified sphygmomanometer test for assessing upper limb and trunk muscle strength in adolescents

The Modified Sphygmomanometer Test (MST) is a method for assessing muscle strength that offers objective measures similar to those of a portable dynamometer, while also being cost-effective. However, previous studies have not investigated the measurement properties of the MST in adolescents. Thus, the objectives of the study were (1) to examine the concurrent criterion validity, test-retest and interrater reliability of the Modified Sphygmomanometer Test (TMS) for assessing muscle strength in adolescents, (2) to calculate the Standard Error of Measurement (EPM) and the smallest real difference (SRD) of muscle strength values; and (3) analyze the different forms of operationalization and their influence on the results obtained. Fifty-two adolescents (mean age: 16.5 ± 0.70 years) participated in the study. Muscle strength of the upper limbs (UL) and trunk was assessed using the MST and portable dynamometers. The Spearman test was used to determine concurrent criterion validity and the intraclass correlation coefficient (ICC) was used to assess reliability (α = 0.05). To analyze the stability of the measurements (SEM and SRD), the 95% test-retest confidence interval (CI) and inter-rater reliability were considered for all data collected. ANOVA was performed to explore different methods of operationalizing the MST. Criterion validity, test-retest reliability and moderate to very high inter-rater reliability (0.61≤r ≤ 0.94; p < 0.001; 0.63≤ICC≤0.97; p < 0.001) were found for the groups assessed muscles and different forms of operationalization, with no statistically significant differences between the different operationalization approaches. Therefore, the MST demonstrated adequate measurement properties for assessing muscle strength in adolescents.

Study on the Microstructure Evolution and Strength Deterioration of Powder Crystal Dolomite under Dissolution

To study the influence of water–rock interactions on the deterioration of rock, particularly the problems of the complex dissolution mechanism of dolomite and the difficulty in establishing chemical damage, dolomite obtained from a tunnel in Yuxi City was utilized. The macroscopic and microscopic dissolution characteristics of dolomite were analyzed using an indoor dissolution test combined with the hydrochemical characteristics of the study area, which were found to be favorable for dissolution. The dissolution of dolomite indicates the chemical decomposition of dolomite crystals, and the crystal failure mode is divided into intergranular dissolved pores and intracrystalline micropore development. Under various pH conditions, as H + is immersed in the rock sample, the failure mode of the rock sample develops from longitudinal cracks to transverse and longitudinal staggered cracks. Based on the aforementioned conclusions, in addition to the principle of chemical kinetics and the generalized Lemaitre strain equivalence principle, a damage model suitable for dolomite chemical erosion was defined. The fitting degree between the calculated value of uniaxial compressive strength and the experimental value reaches 98%, which is of excellent prediction accuracy and reliability. The model for dolomite chemical damage proposed herein provides a theoretical basis for dolomite dissolution damage; the theory of rock chemical damage is thereby enhanced.

Effects of the application protocol and bonding strategy of the universal adhesive on dentin previously impregnated with bioceramic sealer

PurposeTo evaluate the effects of the application of universal adhesive with manual brush (MB) or rotary brush (RB), in the etch-and-rinse (ER) or self-etching (SE) strategy, on the bond strength, adhesive layer thickness, and adhesive failure pattern to dentin impregnated with bioceramic sealer, at 24 h and 1 year. Materials and methodsEighty-eight bovine incisor crowns were impregnated with bioceramic sealer was kept for 15 min and cleaned with cotton soaked in distilled water. They were then divided into four groups (n = 22): ER-MB, ER-RB, SE-MB, SE-RB. Subsequently, the specimens were restored with Filtek Z-250 resin. The adhesive layer thickness was individually analyzed using laser confocal microscope. Bond strength was assessed through microtensile testing, and the failure pattern was examined using a stereomicroscope. Data were analyzed by one-way ANOVA/Tukey's tests (α = 0.05). ResultsThe adhesive layer thickness provided by ER-MB and SE-MB was greater than that provided by ER-RB and SE-RB (P < 0.05). ER-MB showed the lowest bond strength at 24 h (P < 0.05). At 1 year, SE-MB and SE-RB exhibited the highest bond strength values (P < 0.05). ER-MB demonstrated a higher incidence of adhesive failure at 24 h. At 1 year, SE-RB and SE-MB showed a higher incidence of mixed failure. ConclusionThe use of Scotchbond Universal® adhesive in the etch-and-rinse strategy applied with a MB negatively affects bond strength at 24 h, worsening after 1 year of control, regardless of the application protocol.

Investigation on the Correlation between Mechanical Strength, Grain Size, and Density of Fly Ash Microspheres in the Context of Refining Process.

Fly ash microspheres, also called cenospheres, have many valuable properties that allow them to be widely used. Some of its most important properties are its mechanical and thermal strength as well as its chemical stability. These features constitute an important commercial parameter. Refining processes aim to select the highest quality product from raw materials that meets the expectations of recipients. Generally, preparing a final product involves selecting the appropriate sequence and parameters of the grain separation process. However, the key to the optimal selection of these parameters is knowledge of the specificity of the processed raw material. Microspheres are materials that are created spontaneously, uncontrolled, and without the possibility of intentionally influencing their properties. Therefore, due to the potential directions of microsphere use, it is justified to study the relationship between density, grain size, and mechanical strength. Understanding these relationships in microspheres from various sources is particularly important at the stage of planning refining processes. This paper presents the results of research on microspheres from two different sources. The tested raw materials (microspheres) are subjected to densiometric and grain analysis. Also, mechanical strength was determined for the separated density fractions and grain classes. The test results did not show significant correlations between the tested features of the microspheres. In the case of both raw materials, the highest density was observed in the smallest grain classes, and the highest mechanical strength was determined for microspheres with grain sizes in the range of 75-100 µm. For this grain size range, the value of mechanical strength is 26 for raw Material 1 and 38 for raw Material 2. The shares of this grain fraction in the microsphere stream are 11.2% and 16%, respectively. An important difference that may significantly affect the efficiency of the refining process is the method of distribution of the primary falling parts, which affects the mechanical strength of the tested raw materials.

Sustainable Cationic Cotton with Keratin Hydrolysate

In this research work, the keratin hydrolysate was obtained from waste wool by using alkaline hydrolysis. The extracted keratin hydrolysate was treated to the cotton fabric, and then reference and treated fabrics dyed with direct dyestuffs in neutral medium without salt. It was revealed that there was improvement in treated fabric in terms of dyeability and dry crease recovery angle compared to untreated fabric and that wet fastness values and tensile strength values of treated fabric remained same compared to those of untreated fabric. The structural change of treated surfaces was confirmed by SEM, FTIR, XPS and TEM analyses.

Establishment of regression-based isometric strength reference values for the upper limb in persons with multiple sclerosis.

Muscle weakness is common and significantly affects persons with multiple sclerosis (PwMS), with dysfunction in upper limb (UL) muscle groups occurring in approximately 60% of PwMS. To develop gender-specific regression-based prediction equations, with 95% confidence intervals for maximal bilateral UL isometric strength (shoulder abduction and adduction, wrist flexion and extension) and hand grip strength in PwMS. Cross-sectional study. Comprehensive MS center. 256 PwMS. Not Applicable. Shoulder abduction and adduction and wrist flexion and extension isometric strength(Biodex System 4 Pro Dynamometer) and hand grip strength (Jamar handheld dynamometer) were measured. Disease characteristics (disability and disease duration) and demographics (age, height, and weight) were collected. Regression-based predictive equations were generated for the UL muscle groups for each gender and limb, using age, height, weight, disability, and disease duration as covariates. Variables were compared between genders using the Mann-Whitney U test. Maximal voluntary contraction (MVC) reference values (mean ± SD) were reported based on age (<30, 30-39, 40-49, 50-59, 60-69 years) and disability (mild, moderate, severe ambulant, and severe nonambulant) for each gender and limb. Regression-based equations were developed for both genders' strongest and weakest limb, accounting for age, height, weight, disability, and disease duration. MVC was higher in men than women (p < .001) in all muscle groups. Overall, MVC was significantly related to age in 14, height in 5, weight in 6, disability in 14, and disease duration in none of the 20 models. This is the first study to provide regression-based prediction equations for strongest and weakest MVC of UL muscle groups and demonstrated an inverse relationship between MVC with disability and age. Regression-based reference strength values can help clinicians understand muscular strength along a spectrum of PwMS and can aid in goal setting and education for realistic outcomes.

Optimizing the Tensile Strength of Weld Lines in Glass Fiber Composite Injection Molding.

Weld line defects, commonly occurring during the plastic product manufacturing process, are caused by the merging of two opposing streams of molten plastic. The presence of weld lines harms the product's aesthetic appeal and durability. This study uses artificial neural networks to forecast the ultimate tensile strength of a PA6 composite incorporating 30% glass fibers (GFs). Data were collected from tensile strength tests and the technical parameters of injection molding. The packing pressure factor is the one that significantly affects the tensile strength value. The melt temperature has a significant impact on the product's strength as well. In contrast, the filling time factor has less impact than other factors. According to the scanning electron microscope result, the smooth fracture surface indicates the weld line area's high brittleness. Fiber bridging across the weld line area is evident in numerous fractured GF pieces on the fracture surface, which enhances this area. Tensile strength values vary based on the injection parameters, from 65.51 MPa to 73.19 MPa. In addition, the experimental data comprise the outcomes of the artificial neural networks (ANNs), with the maximum relative variation being only 4.63%. The results could improve the PA6 reinforced with 30% GF injection molding procedure with weld lines. In further research, mold temperature improvement should be considered an exemplary method for enhancing the weld line strength.

Repairing Al7075 surface using cold spray technology with different metal/ceramic powders

Cold spray process is essentially a coating technique as well as used in repair applications. This method is a low-temperature solid-state process. In this study, the damaged surface of Al7075 was repaired by low pressure cold spray method with Ni-Zn-Al2O3, Al-Zn-Al2O3, Al-Al2O3, Ni-Al2O3, and Zn-Al2O3 metal/ceramic feedstock powders. Microstructure examination, microhardness measurements, tribological experiments, and tensile tests were conducted on the repaired samples and compared with Al7075. The repaired regions exhibited a composite microstructure characterized by the presence of Al2O3 ceramic particles with high hardness dispersed within a metal matrix composed of Al, Ni, Zn, Ni-Zn, and Al-Zn. This composite structure was attributed to the interlocking mechanism of cold spray. The highest hardness value was measured in the repaired area using Ni-Al2O3, which is approximately 1.28 times higher than that of Al7075 alloy. According to the dry sliding test, the wear performance of all repaired specimens was superior to that of Al7075. The wear resistance of samples repaired with Ni-Al2O3 and Ni-Zn-Al2O3 increased approximately 7.1 and 5.8 times, respectively, compared to Al7075. The specimens repaired with Ni-Zn-Al2O3 feedstock powder showed the most similar results in tensile and yield strength values to Al7075 to the tensile test.

Optimization of an Aerospace Bracket by Additive Manufacturing with Continuous Fiber Reinforced Plastics

Fused Deposition Modelling (FDM), one of the most widely used methods of Additive Manufacturing Technique known as 3D Printing, is a popular technique used to produce different engineering components using common engineering fibre. Carbon fibre filament. This study presents an experimental study examining the effect of printing parameters on the mechanical properties of components produced with Carbon fibre filaments. The effects of the printing parameters determined as infill pattern, infill density and nozzle temperature on the mechanical strength parameter determined as tensile strength and flexural strength of Carbon fibre samples produced in standard sizes were investigated experimentally. The experimental design was carried out in accordance with the Taguchi L9 orthogonal array, and the relationship between the printing parameters and the mechanical strength parameters was modelled mathematically. The predicted strength values calculated using mathematical models were compared with the experimental test results. The results showed that the tensile strength and flexural strength values were directly proportional to the infill density. Experiments have shown that the most effective 3D printing parameter on the mechanical strength parameters is the infill density parameter with a contribution ratio of 62.09% for tensile strength and 72.83% for flexural strength. As a result of the RSM optimization, it was determined that the infill density 60%, the nozzle temperature value 265 C° and the infill pattern type lines to maximize the flexural strength and tensile strength values. Key Words: Sustainable Material, 3D Printing Parameters, Mechanical Strength Optimization, Response Surface Methodology.

Identification of the Core Characteristics of Vulnerable/Hypersensitive Narcissism and its Association with the Dark Triad in a Large International Sample: A Network Analysis Study.

The current paper aimed to investigate the network structure and centrality indexes of hypersensitive narcissism using the hypersensitive Narcissism Scale (HSN). Additionally, we aimed to explore its relationships with dark triad personality aspects. A globally diverse sample of "53,981" participants (47.9% non-United States responders) completed the HSN and Dark Triad Dirty Dozen scale (DTD). We estimated the network structure across genders to determine the core characteristics of hypersensitive narcissism. Additionally, bridge and central nodes (characteristics) were identified. All analyses were performed using R-Studio programming software. The network comparison test indicated significant differences in the network structures between males and females (Network-Invariance: 0.0489, P < 0.01; Global Strength Invariance: 0.101, P < 0.01). In the network of HSN for male participants, characteristics with the highest strength centrality were "Highly affected by criticism" (HSN.2, strength = 1.08) and "Self-absorbed in personal pursuits" (HSN.8, strength = 1.28). For female participants, "Self-absorbed in personal pursuits" (HSN.8, strength = 1.32) and "privately annoyed by others' needs" (HSN.10, strength = 1.21) were the highest central characteristics. The assessment of bridge strength indicated that nodes HSN.2 (Highly sensitive to criticism), scoring 0.42, and DTD.1 (Tendency to manipulate for gain, a component of Machiavellianism), scoring 0.428, showed the highest bridge strength values. The current study identified core characteristics of hypersensitive narcissism and its correlation with dark triad personality, revealing gender-specific patterns and bridging symptoms between the two constructs. These findings showed that focusing on these core characteristics may be advantageous in treating individuals exhibiting elevated levels of narcissism.

Influence of granite micro particles on the mechanical, damping and antimicrobial properties of silk–sisal hybrid composites

This paper focuses on the effect of granite-micro-filler on static mechanical properties, damping behavior, and physical characteristics of silk-sisal hybrid composite. The composites structures are fabricated by using three layers of plain weaves mat with varying weight percentages (2, 4, and 6 wt%) of granite-micro-filler by hand layer process. The effect of granite-micro-filler on silk-sisal is analyzed and results are compared with pure silk-sisal (without granite-Micro-filler) hybrid composite. The results infer that; the tensile strength and flexural strength value of the developed silk-sisal hybrid composites are increased with the increase in wt% of granite-micro-filler content than pure silk–sisal, approximately 5% and 9% improved value in order by adding 6 wt% granite-micro-filler on silk–sisal. The tensile and flexural fracture morphology analysis indicated that composed plain weave of silk–sisal fiber mat with two (longitudinal and transverse) directions possesses higher mechanical properties and also observed that, granite-micro-filler dispersed on silk–sisal fiber mat and resin with closely packed. The improved damping factor is obtained by adding 6 wt% of granite-micro-filler content, which is approximately 75.8% higher than pure silk–sisal. The physical properties of silk–sisal hybrid composite have also been analyzed and well discussed in this paper.

A New Methodology to Estimate the Early-Age Compressive Strength of Concrete before Demolding

Non-destructive testing has many advantages, such as the ability to obtain a large number of data without destroying existing structures. However, the reliability of the estimation accuracy and the limited range of applicable targets remain an issue. This study proposes a novel pin penetration test method to determine the early-age compressive strength of concrete before demolding. The timing of demolding and initial curing is determined according to the strength development of concrete. Therefore, it is important to determine the compressive strength at an early age before demolding at the actual construction site. The applicability of this strength estimation methodology at actual construction is investigated. Small test holes (12 mm in diameter) are prepared on the mold surface in real construction sites and mock-up specimens in advance. The pin is penetrated into these test holes to obtain the relationship between the compressive strength and the penetration depth. As a result, it is confirmed that the pin penetration test method is suitable for measuring the early-age compressive strength at the actual construction site. This allows the benchmark values for compressive strength, necessary to avoid early frost damage, to be directly verified on the concrete structural members at the construction site. For instance, the compressive strengths of greater than 5 MPa and 10 MPa can be confirmed by the penetration depths benchmark values of 8.0 mm and 6.7 mm or less, respectively.

Numerical Simulation of Thermal Therapy for Melanoma in Mice.

In recent years, the progressively escalating incidence and exceptionally high fatality rate of cutaneous melanoma have drawn the attention of numerous scholars. Magnetic induction hyperthermia, as an efficacious tumor treatment modality, has been promoted and applied in the therapy of some tumors. In this paper, the melanoma atop the mice's heads was chosen as the research subject, and a magnetic induction hyperthermia approach based on Helmholtz coils as the magnetic field excitation was investigated and designed. The influence of the electromagnetic field and thermal field on organisms was addressed through modeling by COMSOL simulation software. The results showed that the maximum values of induced electric field and magnetic induction strength in mouse tumor tissues were 63.1 V/m and 8.5621 mT, respectively, which reached the threshold value of magnetic field strength required for magnetic induction hyperthermia. The maxima of the induced electric field and magnetic induction intensity in brain tissues are, respectively, 35.828 V/m and 8.57 mT. Approximately 93% of the tumor tissue can reach 42 °C, and the maximum temperature is 44.2 °C. Within this temperature range, a large quantity of tumor cells can be successfully induced to undergo apoptosis without harming normal cells, and the therapeutic effect is favorable.