Vacuum Ultraviolet Lamp Research Articles

Insights into enhanced degradation of antibiotic trimethoprim in water using a novel K doped g-C3N4 photocatalyst under vacuum-UV irradiation: Performance and mechanisms

In this work, an innovative strategy combining vacuum ultraviolet (VUV) and K doping graphite carbon nitride (K-g-C3N4) was proposed for antibiotic removal in aqueous. The properties of K-g-C3N4 were systematically characterized by XRD, FT-IR, BET, SEM, UV-vis DRS, and XPS, showing that K-g-C3N4 possessed a larger specific surface and richer functional groups than g-C3N4. The catalytic efficiency of K-g-C3N4 was investigated for the trimethoprim (TMP) removal under VUV irradiation. Compared with UVC photolysis, VUV photolysis, UVC/g-C3N4, VUV/g-C3N4, and UVC/K-g-C3N4 processes, VUV/K-g-C3N4 enhanced the pseudo-first-order reaction rate constant of TMP removal by 2.0–19.7 times and the mineralization rate by 9.0%-38.2%. Electron paramagnetic resonance results and quenching experiments validated that O2•-, •OH, 1O2, h+, and e- were engaged in the VUV/K-g-C3N4 process. The fluorescent spectra of O2•--substituted and •OH-substituted products revealed that the K-g-C3N4 greatly enhanced the quantity of O2•- and •OH during VUV irradiation. The VUV/K-g-C3N4 system produced marginally more H2O2 and •OH than the UVC/K-g-C3N4 system, confirming that K-g-C3N4 predominantly utilized the UVC and other ultraviolet–visible light emitted by the VUV lamp, with VUV having a minor effect. Furthermore, K-g-C3N4 had exceptional stability and reusability, efficiently degrading various contaminants under VUV irradiation. This work offered a comprehensive insight into VUV/K-g-C3N4 process as a novel approach for antibiotic removal from water.

Discontinuous Atmospheric Pressure Interface in-Trap Single Photon Ionization Ion Trap Mass Spectrometry (DAPI in-Trap SPI ITMS)

A compact in-trap single photon ionization (SPI) system, termed discontinuous atmospheric pressure interface (DAPI) ion trap mass spectrometry (ITMS), for the rapid determination of trace volatile organic compounds (VOCs). DAPI enables the maintenance of high analyte pressure in the SPI source while preserving the vacuum. Utilizing vacuum ultraviolet (VUV) lamp as the ion source, we ionize the analyte within an enclosed miniature 3D ion trap for efficient analysis. Experimental findings demonstrate that the system achieves a mass resolution of less than 0.5 atomic mass units for full width at half maxima (FWHM), providing unit resolution. For the response for benzene, the system achieves almost instantaneous response, with rise and fall times of only 2 s, which is a significant advantage compared to the membrane inlet (MI) approach necessary for on-site detection. Additionally, tandem mass spectrometry (MS/MS) with unit m/z isolation window was achieved and resolved dimethyl disulfide and phenol with similar molecular weights. Our results demonstrate that the system provides excellent performance and we anticipate its application in rapidly determining VOCs.

A dopant-assisted iodide-adduct chemical ionization time-of-flight mass spectrometer based on VUV lamp photoionization for atmospheric low-molecular-weight organic acids analysis

Formic and acetic acids are the most abundant gaseous organic acids and play the key role in the atmospheric chemistry. In iodine-adduct chemical ionization mass spectrometry (CIMS), the low utilization efficiency of methyl iodide and humidity interference are two major issues of the vacuum ultraviolet (VUV) lamp initiated CIMS for on-line gaseous formic and acetic acids analysis. In this work, we present a new CIMS based on VUV lamp, and the ion-molecular reactor is separated into photoionization and chemical ionization zones by a reducer electrode. Acetone was added to the photoionization zone, and the VUV photoionization acetone provided low-energy electrons for methyl iodide to generate I−, and the addition of acetone reduced the amount of methyl iodide by 2/3. In the chemical ionization zone, a headspace vial containing ultrapure water was added for humidity calibration, and the vial changes the sensitivity as a function of humidity from ambiguity to well linear correlation (R2 > 0.95). With humidity calibration, the CIMS can quantitatively measure formic and acetic acids in the humidity range of 0%-88% RH. In this mode, limits of detection of 10 and 50 pptv are obtained for formic and acetic acids, respectively. And the relative standard deviation (RSD) of quantitation stability for 6 days were less than 10.5%. This CIMS was successfully used to determine the formic and acetic acids in the underground parking and ambient environment of the Shandong University campus (Qingdao, China). In addition, we developed a simple model based formic acid concentration to assess vehicular emissions.

Novel MCP-Windowed EUV Light Source and Its Mass Spectrometric Application for Detecting Chlorinated Methanes.

Various vacuum ultraviolet (VUV) lamps are simple and convenient VUV light sources for mass spectrometry and other research fields. However, the strong absorption of high-energy photons by window materials limits the application of an extreme ultraviolet (EUV) light. In this study, a novel high-flux EUV light source is developed using a microchannel plate (MCP) window to transmit 73.6 nm (16.9 eV) EUV light generated via the radio frequency (RF) inductive discharge of neon. The MCP used is a 0.5 mm thick glass plate with a regular array of microtubes (12 μm i.d.). The photon fluxes of the EUV light source with the MCP window (12 mm i.d.) and an aperture (1.8 mm i.d.) are ∼1.31 × 1014 and ∼9.80 × 1012 photons s-1, respectively, while their corresponding leakage flow rates of the discharge gas are 0.062 and 0.046 cm3 atom s-1, according to the contrast experiments. The transmission efficiency of the MCP to the EUV light is 30.2%, with a 1.2% deviation. An EUV photoionization time-of-flight mass spectrometer (EUV-PI-TOFMS) is built to validate the practicality of the MCP-windowed EUV light source further. The detection sensitivities in 30 s measurements for methyl chloride (CH3Cl), methylene chloride (CH2Cl2), trichloromethane (CHCl3), and carbon tetrachloride (CCl4) in synthetic air are 4366, 4120, 5854, and 4095 counts ppbv-1, respectively. The corresponding 3σ limits of detection (LODs) are 42, 34, 24, and 15 pptv. This study develops a new feasible method for efficiently utilizing high-energy EUV light, with many application prospects in scientific research.

Development and Application of a Chemical Ionization Focusing Integrated Ionization Source TOFMS for Online Detection of OVOCs in the Atmosphere.

Single photon ionization (SPI) based on vacuum ultraviolet (VUV) lamps has been extensively investigated and applied due to its clean mass spectra as a soft ionization method. However, the photon energy of 10.6 eV and photon flux of 1011 photons s-1 of a commercial VUV lamp limits its range of ionizable analytes as well as its sensitivity. This work designs a chemical ionization focusing integrated (CIFI) ionization source time-of-flight mass spectrometry (TOFMS) based on a VUV lamp for the detection of volatile organic compounds (VOCs) and oxygenated volatile organic compounds (OVOCs). The photoelectrons obtained from the VUV lamp via the photoelectric effect ionized the oxygen and water in the air to obtain the reagent ions. The ion-molecule-reaction region (IMR) is constituted by a segmented quadrupole that radially focuses the ions using a radio-frequency electric field. This significantly enhances the yield and transport efficiency of the product ions leading to a great improvement in sensitivity. As a result, a 44-fold and 1154-fold increase in the signal response for benzene and pentanal were achieved, respectively. To verify the reliability of the ionization source, the linear correspondence and repeatability of benzene and pentanal were investigated. Satisfactory dynamic linearity was obtained in the mixing ratio range of 5-50 ppbv, and the relative standard deviation (RSD) of inter-day reached 3.91% and 6.26%, respectively. Finally, the CIFI-TOFMS was applied to the determination of OVOCs, and the LOD of 12 types of OVOCs reached the pptv level, indicating that the ionization source has the potential for accurate and sensitive online monitoring of atmospheric OVOCs.

A Simple High-Flux Switchable VUV Lamp Based on an Electrodeless Fluorescent Lamp for SPI/PAI Mass Spectrometry.

Single-photon ionization (SPI) is a unique soft ionization technique for organic analysis. A convenient high-flux vacuum ultraviolet (VUV) light source is a key precondition for wide application of SPI techniques. In this study, we present a novel VUV lamp by simply modifying an ordinary electrodeless fluorescent lamp. By replacing the glass bulb with a stainless steel bulb and introducing 5% Kr/He (v/v) as the excitation gas, an excellent VUV photon flux over 4.0 × 1014 photons s-1 was obtained. Due to its rapid glow characteristics, the VUV lamp can be switched on and off instantly as required by detection, ensuring the stability and service life of the lamp. To demonstrate the performance of the new lamp, the switchable VUV lamp was coupled with an SPI-mass spectrometer, which could be changed to photoinduced associative ionization (PAI) mode by doping gaseous CH2Cl2 to initiate an associative ionization reaction. Two types of volatile organic compounds sensitive to SPI and PAI, typically benzene series and oxygenated organics, respectively, were selected as samples. The instrument exhibited a high detection sensitivity for the tested compounds. With a measurement time of 11 s, the 3σ limits of detection ranged from 0.33 to 0.75 pptv in SPI mode and from 0.03 to 0.12 pptv in PAI mode. This study provides an extremely simple method to assemble a VUV lamp with many merits, e.g., portability, robustness, durability, low cost, and high flux. The VUV lamp may contribute to the development of SPI-related highly sensitive detection technologies.

Ultrathin Silica Integration for Enhancing Reliability of Microfluidic Photoionization Detectors.

Microfluidic photoionization detectors (μPIDs) based on silicon chips can rapidly and sensitively detect volatile compounds. However, the applications of μPID are limited by the manual assembly process using glue, which may outgas and clog the fluidic channel, and by the short lifetime of the vacuum ultraviolet (VUV) lamps (especially, argon lamps). Here, we developed a gold-gold cold welding-based microfabrication process to integrate ultrathin (10 nm) silica into μPID. The silica coating enables direct bonding of the VUV window to silicon under amicable conditions and works as a moisture and plasma exposure barrier for VUV windows that are susceptible to hygroscopicity and solarization. Detailed characterization of the silica coating was conducted, showing that the 10 nm silica coating allows 40-80% VUV transmission from 8.5 to 11.5 eV. It is further shown that the silica-protected μPID maintained 90% of its original sensitivity after 2200 h of exposure to ambient (dew point = 8.0 ± 1.8 °C), compared to 39% without silica. Furthermore, argon plasma inside an argon VUV lamp was identified as the dominant degradation source for the LiF window with color centers formation in UV-vis and VUV transmission spectra. Ultrathin silica was then also demonstrated effective in protecting the LiF from argon plasma exposure. Lastly, thermal annealing was found to bleach the color centers and restore VUV transmission of degraded LiF windows effectively, which will lead to future development of a new type of VUV lamp and the corresponding μPID (and PID in general) that can be mass produced with a high yield, a longer lifetime, and better regenerability.

Selective supply of atomic oxygen to a surface placed in room air using vacuum ultraviolet photolysis of carbon dioxide

Reactive species play important roles in plasma treatments of surfaces, including polymers, metals, water, and living tissues. To elucidate the surface reaction mechanism, it is crucial to measure the effect of each type of reactive species on the surface treatment. Accordingly, we previously developed a method to selectively supply OH or O radicals to a surface placed in room air. Ar/H2O or Ar/O2 gas flowing through a quartz tube is irradiated with a vacuum ultraviolet lamp, causing photodissociation of H2O and O2 to produce OH and O. The resulting gas flows to the surface from the tube end. The O density supplied to the surface, however, is only approximately cm−3 according to our simulation, which is not sufficient to determine the surface treatment effect of O atoms. Therefore, in this study, a new method is proposed, supplying O atoms with a density that is two orders of magnitude higher. Specifically, CO2 gas is used as the medium to be photodissociated instead of O2 gas. The performance of this method is discussed herein using simulation results. The maximum O density supplied to the surface reaches cm−3 according to the simulation. Additionally, the experimental results demonstrate that the newly developed method can supply a sufficient amount of O atoms to selectively measure the effect of O atoms on the surface treatment of polypropylene (PP). In particular, the water contact angle (WCA) is considered as an index of the surface treatment. As a result, O atoms decrease the WCA of the PP surface at rates of the same order of magnitude as OH.

Degradation mechanism of BPA under VUV irradiation: efficiency contribution and DFT calculations.

Bisphenol A (BPA) is regarded as a hazardous pollutant that exists widely in aquatic environments, posing a severe threat to human health. In this study, a vacuum ultraviolet (VUV) lamp emitting a hybrid of 254nm and 185nm light was used to degrade BPA. Results indicated that photolysis via 254nm wavelength accounted for 24.93% for BPA decay, while indirect oxidation was responsible for 52.27% of decay. Results confirmed that the degradation of BPA under VUV illumination mainly occurred via photo-excited degradation and ·OH electrophilic addition reactions based on average local ionization energy (ALIE) calculation and density functional theory (DFT) calculations. Therefore, only light with a wavelength of 254nm was able to induce the first three excited states of BPA, forming the electron transition type of n → π* from O atom to a single benzene ring and π → π* in the single benzene ring. Indirect oxidation by ·OH occurred as it preferentially attacked the C6 atom in BPA ring A. Moreover, the energy required for photo-excited degradation was about twofold than that of ·OH electrophilic addition reactions.

Commercialization of microcavity plasma devices and arrays: Systems for VUV photolithography and nanopatterning, disinfection of drinking water and air, and biofilm deactivation for medical therapeutics

AbstractA little more than two decades after the introduction of the first microcavity plasma devices, a growing body of commercial products based on the remarkable properties of these low‐temperature, atmospheric plasmas is now available. Following a brief review of early microplasma lamp development, this article describes microplasma‐based devices and systems currently being manufactured for applications in photolithography, photopatterning, and other nanofabrication processes, such as atomic layer deposition, spectroscopic identification and analysis of materials (including wide bandgap crystals), the disinfection of drinking water in off‐grid communities, deactivating COVID‐19 and other pathogens in air and on surfaces in public spaces, and vacuum ultraviolet lamps for driving atomic clocks. The microplasma‐based treatment of otitis media in the human ear will also be discussed.

An ultrasensitive SPI/PAI ion source based on a high-flux VUV lamp and its applications for the online mass spectrometric detection of sub-pptv sulfur ethers

Single-photon ionization mass spectrometry (SPI-MS) is an attractive analytical technique for the online detection of volatile organic compounds; however, the low photon flux of the vacuum ultraviolet (VUV) lamp commonly used in the SPI ion source and the corresponding low detection sensitivity remain a constraint to its wide field applications. In this study, a new VUV lamp-based SPI ion source was developed. By increasing the discharging volume and optimizing the configuration of the lens and ionizer, the photon flux of the VUV lamp and the sensitivity of the ion source were significantly improved. The VUV lamp output was 2.8 × 1015 photons s−1, which was focused into the small ionization zone, and the ion intensity of gaseous benzene under SPI achieved 1.7 × 104 counts per second per pptv (cps pptv−1). This ion source can also function in photoinduced associative ionization (PAI) mode by introducing gaseous CH2Cl2 to initiate an associative ionization reaction. Because of the high efficiency of the ion source, the amount of doped CH2Cl2 needed for PAI was greatly reduced (∼2.5% of that used in previous experiments). PAI exhibited an outstanding protonation effect on monosulfur ethers (CnH2n+1S). The signal intensities of the protonated molecular ions (MH+) were 46–128 times higher than those of the molecular ions (M+) produced by SPI. Since monosulfur ethers generally have lower SPI cross-sections than polysulfur ethers (CnH2n+1S2 or CnH2n+1S3), the PAI and SPI modes were selected for the online measurement of a series of mono- and polysulfur ethers, respectively. The obtained detection sensitivity of the mono- and polysulfur ethers reached 476.5 ± 1.72–2835.1 ± 99.5 and 47.9 ± 0.4–105.1 ± 2.3 counts pptv−1, respectively, in 10 s of sampling time. The corresponding 3σ limits of detection (LODs) were 0.12–0.71 and 0.06–0.14 pptv, respectively. This study provides advances in the development of a high-flux VUV lamp and a highly efficient SPI/PAI ion source, as well as an ultrasensitive analytical method for detecting sulfur ethers.

Protonated acetone ion chemical ionization time-of-flight mass spectrometry for real-time measurement of atmospheric ammonia

Ammonia (NH3) is ubiquitous in the atmosphere, it can affect the formation of secondary aerosols and particulate matter, and cause soil eutrophication through sedimentation. Currently, the use of radioactive primary reagent ion source and the humidity interference on the sensitivity and stability are the two major issues faced by chemical ionization mass spectrometer (CIMS) in the analysis of atmospheric ammonia. In this work, a vacuum ultraviolet (VUV) Kr lamp was used to replace the radioactive source, and acetone was ionized under atmospheric pressure to obtain protonated acetone reagent ions to ionize ammonia. The ionization source is designed as a separated three-zone structure, and even 90 vol.% high-humidity samples can still be directly analyzed with a sensitivity of sub-ppbv. A signal normalization processing method was designed, and with this new method, the quantitative relative standard deviation (RSD) of the instrument was decreased from 17.5% to 9.1%, and the coefficient of determination was increased from 0.8340 to 0.9856. The humidity correction parameters of the instrument were calculated from different humidity, and the ammonia concentrations obtained under different humidity were converted to its concentration under zero humidity condition with these correction parameters. The analytical time for a single sample is only 60 sec, and the limit of detection (LOD) was 8.59 pptv (signal-to-noise ratio S/N = 3). The ambient measurement made in Qingdao, China, in January 2021 with this newly designed CIMS, showed that the concentration of ammonia ranged from 1 to 130 ppbv.

Atmospheric Photoionization Detector with Improved Photon Efficiency: A Proof of Concept for Application of a Nanolayer Thin-Film Electrode.

Atmospheric photoionization is a widely applied soft ionization mechanism in gas sensing devices for the detection of volatile organic compounds in ambient air. Photoionization is typically induced by low-pressure Vacuum Ultraviolet (VUV) lamps with MgF2 or LiF lamp surface windows depending on the gas fill and the required wavelength transmission window. These lamps are known to exhibit gradually reduced VUV transmission due to hydrocarbon contamination. LiF surface windows are known to be especially problematic due to their hygroscopic nature, reducing VUV lamp lifetime to a mere 100 h, approximately. Here, we present a new design for the electrode of a photoionization detector based on thin-film technology. By replacing the commonplace metal grid electrode’s VUV lamp surface window with a chromium/gold thin film we obtain a doubling of photon efficiency for photoionization. Replacing the hygroscopic LiF lamp window surface with a metallic layer additionally offers the possibility to vastly increase operational lifetime of low-pressure Argon VUV lamps.

Reactivity and mechanism between [rad]OH and phenolic pollutants: Efficiency and DFT calculation

Phenolic pollutants (PPs) are regarded as hazardous pollutants, posing severe threats to humans. In this study, a vacuum ultraviolet (VUV) lamp was used to decay PPs with different functional groups, including phenol, paradioxybenzene (PDB), and p-nitrophenol (PNP). Results showed the removal rate for phenol, PDB, and PNP reached 99.78 %, 97.78 %, and 80.73 % within 60 min. Density functional theory (DFT) involving in quantum chemical descriptors (QCD), frontier molecular orbitals (FMO), thermochemical properties, and the Gibbs free energy was applied to reveal the reactivity and mechanism between ·OH and PPs with various functional groups. Results confirmed that PDB and phenol with the electron-donating group exhibited favorable reactivity, while PNP with an electron-withdrawing group presented a lower one. Furthermore, the oxidation mechanism between PPs and ·OH in the VUV system was also deeply investigated, mainly following four steps: photo-excitation, ·OH substitution, molecular rearrangement, and finally ring-opening. Among them, the required energy for the ring-opening was about 145 and 787-fold higher than that of ·OH substitution and molecular rearrangement. Results suggested that the formation of micro-fatty acids were the primary rate-controlling step.

A vacuum ultraviolet ion source (VUV-IS) for iodide–chemical ionization mass spectrometry: a substitute for radioactive ion sources

Abstract. A new ion source (IS) utilizing vacuum ultraviolet (VUV) light is developed and characterized for use with iodide–chemical ionization mass spectrometers (I−-CIMS). The VUV-IS utilizes a compact krypton lamp that emits light at two wavelengths corresponding to energies of ∼10.030 and 10.641 eV. The VUV light photoionizes either methyl iodide (ionization potential, IP = 9.54 ± 0.02 eV) or benzene (IP = 9.24378 ± 0.00007 eV) to form cations and photoelectrons. The electrons react with methyl iodide to form I−, which serves as the reagent ion for the CIMS. The VUV-IS is characterized by measuring the sensitivity of a quadrupole CIMS (Q-CIMS) to formic acid, molecular chlorine, and nitryl chloride under a variety of flow and pressure conditions. The sensitivity of the Q-CIMS, with the VUV-IS, reached up to ∼700 Hz pptv−1, with detection limits of less than 1 pptv for a 1 min integration period. The reliability of the Q-CIMS with a VUV-IS is demonstrated with data from a month-long ground-based field campaign. The VUV-IS is further tested by operation on a high-resolution time-of-flight CIMS (TOF-CIMS). Sensitivities greater than 25 Hz pptv−1 were obtained for formic acid and molecular chlorine, which were similar to that obtained with a radioactive source. In addition, the mass spectra from sampling ambient air was cleaner with the VUV-IS on the TOF-CIMS compared to measurements using a radioactive source. These results demonstrate that the VUV lamp is a viable substitute for radioactive ion sources on I−-CIMS systems for most applications. In addition, initial tests demonstrate that the VUV-IS can be extended to other reagent ions by the use of VUV absorbers with low IPs to serve as a source of photoelectrons for high IP electron attachers, such as SF6-.

Online analysis of gas-phase radical reactions using vacuum ultraviolet lamp photoionization and time-of-flight mass spectrometry

A home-made vacuum ultraviolet photoionization time-of-flight mass spectrometer has been developed and coupled to an atmospheric simulation chamber operated at atmospheric pressure and to a fast flow tube at low pressure (1-10 Torr). Gas sampling from the simulation chamber is realized directly via a capillary effusive beam, and sampling from the flow tube is via a continuous molecular beam inlet. Both devices are connected simultaneously to the ionization chamber of the mass spectrometer and can be switched in-between within minutes to study gas-phase radical reactions of atmospheric interest in a large range of reaction conditions and reaction times (from milliseconds in the flow tube to hours in the simulation chamber). A cage-shaped photoionization source combined with a commercial 10.6 eV krypton lamp has been developed to provide a high ion collection efficiency along the long light path in the cage. This way, a multiplexed detection with high sensitivity down to the sub-parts per billion volume concentration range, e.g., a limit of detection of 0.3 ppbv with an accumulation time of 60 s for benzene and 1.3 ppbv for the methyl radical, is obtained. The performance and suitability of the setup are illustrated by the study of the chlorine-initiated oxidation reaction of toluene in the atmospheric simulation chamber and in the fast flow tube. Stable products and reactive intermediates have been well-determined and their reaction dynamics are discussed.

Highly selective and sensitive online measurement of trace exhaled HCN by acetone-assisted negative photoionization time-of-flight mass spectrometry with in-source CID

Exhaled hydrogen cyanide (HCN) has been extensively investigated as a promising biomarker of the presence of Pseudomonas aeruginosa in the airways of patients with cystic fibrosis (CF) disease. Its concentration profile for exhalation can provide useful information for medical disease diagnosis and therapeutic procedures. However, the complexity of breath gas, like high humidity, carbon dioxide (CO2) and trace organic compounds, usually leads to quantitative error, poor selectivity and sensitivity for HCN with some of existing analytical techniques. In this work, acetone-assisted negative photoionization (AANP) based on a vacuum ultraviolet (VUV) lamp with a time-of- flight mass spectrometer (AANP-TOFMS) was firstly proposed for online measurement of trace HCN in human breath. In-source collision-induced dissociation (CID) was adopted for sensitivity improvement and the signal response of the characteristic ion CN− (m/z 26) was improved by about 24-fold. For accurate and reliable analysis of the exhaled HCN, matrix influences in the human breath including humidity and CO2 were investigated, respectively. A Nafion tube was used for online dehumidification of breath samples. Matrix-adapted calibration in the concentration range of 0.5–50 ppbv with satisfactory dynamic linearity and repeatability was obtained. The limit of quantitation (LOQ) for HCN at 0.5 ppbv was achieved in the presence of 100% relative humidity and 4% CO2. Finally, the method was successfully applied for online determination of human mouth- and nose-exhaled HCN, and the nose-exhaled HCN were proved to be reliable for assessing systemic HCN levels for individuals. The results are encouraging and highlight the potential of AANP-TOFMS with in-source CID as a selective, accurate, sensitive and noninvasive technique for determination of the exhaled HCN for CF clinical diagnosis and HCN poisoning assessment.

Evaluation of an online, real-time, soft-photon ionisation time-of-flight mass spectrometer for mainstream tobacco smoke analysis

Mainstream tobacco smoke is a complex and dynamic aerosol, consisting of particulate and vapour phases. Most approaches to determine mainstream smoke toxicant yields are based on offline techniques that limit the opportunity to observe in real time the processes leading to smoke formation. The recent development of online real-time analytical methods offers many advantages over traditional techniques. Here we report the LM2X-TOFMS (Borgwaldt GmbH, Germany), a commercial instrument that couples a linear smoking engine with a time-of-flight mass spectrometer for real-time per-puff measurement of the vapour phase of mainstream cigarette smoke. Total cigarette and puff-by-puff (μg/puff) yields were evaluated, in line with International Council of Harmonisation recommendations, for seven smoke toxicants: acetaldehyde, acetone, 1,3-butadiene, 2-butanone, benzene, isoprene and toluene. Measurements were unaffected by small system changes including replacing the sampling capillary or time of day (all P > 0.05), indicating that the LM2X-TOFMS is rugged. Control charts showed that the system has good stability and control. Analysis of certified gas mixtures of six concentrations of each analyte showed a highly linear response for all seven analytes (R2 = 0.9922–0.9999). In terms of repeatability, the lowest variation was observed for isoprene with a coefficient of variation (CV) of < 6% for each concentration. Acetaldehyde showed the highest CV, increasing from 8.0 to 26.6% with decreasing gas concentration. Accuracy was analysed in terms of relative error, which was ± 16% for six of the analytes; however, the relative error for acetaldehyde was (− 36.2%), probably due to its low ionisation efficiency under the instrument’s vacuum ultraviolet lamp. Three cigarette products (reference and commercial) with different ISO tar levels were analysed by the LM2X-TOFMS puff by puff under ISO regulatory smoking conditions. The relative standard deviation based on average yield per cigarette for each analyte in each product (summed puffs per product, n = 30) ranged from ≤ 9.3 to ≤ 16.2%. Measurements were consistent with published data per cigarette. In conclusion, the LM2X-TOFMS is suitable for determining the vapour-phase yields of seven analytes on a real-time, puff-by-puff basis, and can be utilised for both fast screening (qualitative) and quantitative measurements of mainstream cigarette smoke.

Characterization of crucial fragments during the nucleation and growth of secondary organic aerosol from the high-NO photo-oxidation of α-pinene

We propose the use of thermal-desorption dichloromethane-induced low-pressure photoionization mass spectrometry (TD-CH2Cl2-induced LPPI-MS) via a laboratory-built krypton vacuum ultraviolet lamp for the real-time analysis of α-pinene secondary organic aerosol (αP-SOA). Using this technology, the peak intensities of the majority of SOA were enhanced by at least two orders of magnitude after doping with 720 ppm dichloromethane. Clear temporal evolutions of the SOA oxidation products with particle formation were also observed. The molecular ion peaks at m/z value of 153 and 109 showed a similar sharp increase with particle-number concentration. These two species (i.e. protonated α-campholenic aldehyde or dehydrated protonated pinalic-3-acid) with the fragment at m/z 153 and 109 may be critical species to prompt new particle formation. Furthermore, the monomers with the fragment ion peaks at m/z value of 69 and 87 (i.e. protonated pinonic acid, pinic acid, oxopinonic acid, and OH-pinonic acid etc.) were found to be intermediate species with high reactivities during SOA growth. The obtained results provide supplementary knowledge regarding the characterization and temporal evolution of the key components that promote αP-SOA formation.

Microprobe for the Thermal Analysis of Crude Oil Coupled to Photoionization Fourier Transform Mass Spectrometry.

We present the simple microprobe for the investigation of crude oil by a thermal desorption photoionization coupled to Orbitrap mass spectrometry. The droplet of crude oil was placed on the heating element with controllable temperature. The temperature was linearly increased, and crude oil vapors were ionized by a vacuum ultraviolet (VUV) lamp and detected by Orbitrap mass spectrometer. Use of modified Orbitrap allowed introduction of the heating element and VUV lamp directly into the ion funnel and performing experiment not only at atmosphere pressure but also at 20, 10, and 5 torr. We observed that at high pressure protonated CHN compounds dominate in the spectrum, while at the low pressure CH compounds dominate. Similar to previously reported thermogravimetry coupled to photoionization or chemical ionization mass spectrometry systems we were able to separate compounds with different desorption energy and reliably detect low-abundant compounds. Also, we were able to determine the desorption temperature for each compound of the crude oil. We found that temperature of desorption increases linearly with m/ z for compounds that belong to the same homology series (same Kendrick mass defect). This may serve as indirect evidence that such compounds differ only by the length of aliphatic chains attached to some basic structure.