Testing Machine Research Articles

Effect of Inter-Implant Distance on Fracture Resistance of Implant-Supported Provisional Fixed Dental Prosthesis.

This study aimed to identify the ideal interimplant distance for optimum outcome on immediately loaded implant supported prosthesis. Hence this study was taken up to analyze the effect of varying interimplant distance on fracture resistance of implant supported provisional fixed dental prosthesis (FDP). A total of 24 bis-acrylate composite resin samples were prepared. Interimplant distance was present in the metal die for placement of dummy implants at distances of 14 mm, 21 mm, and 30 mm respectively. Wax-up for 3-unit, 4-unit, and 5-unit implant-supported provisional restoration was made. Silicone molds were used for making multiple interim prostheses using bis-acrylate composite material. All samples were subjected to fracture test in the universal testing machine with a crosshead speed of 1 mm/min. All samples were loaded with gradual force starting from 100 N until it fractured. The load was applied at the center of prosthesis. Data was analyzed by one-way analysis of variance and Bonferroni post hoc test. Mean fracture resistance of 3-unit provisional FDP at 14 mm of interimplant distance showed 1342.61 ± 179.15 N. Mean fracture resistance of 4-unit provisional FDP at 21 mm of interimplant distance showed 1420.44 ± 170.37 N. Mean fracture resistance of 5-unit provisional FDP at 30 mm of interimplant distance showed 791.61 ± 203.59 N. Both 14 mm and 21 mm of interimplant distance are suitable span lengths to be considered for the optimum outcome during immediately loading with implant-supported provisional restorations. Limitations of the study were that force application was static in nature and not dynamic and the arch form was not "U" shaped but longitudinal using Bis-Acryl material only with no cantilever. Future studies can be done to evaluate the fracture resistance of bis-acrylate material considering biomechanics and arch form of natural dentition. Distal cantilever should be considered along with different material for fabricating provisional restoration.

Structural Characterization and Grading of Timber Species for Engineering Applicability in Kenya

An investigation was carried out in Kakamega County to determine the characteristic grade of eucalyptus and cypress timber species that are commonly used in construction. The physical and mechanical properties of two timber species for structural use; eucalyptus and cypress were determined. Six logs of each species were obtained from different areas of Kakamega County, sliced into 2” by 12” size before seasoning under a shade and their structural strength properties were determined at a moisture content of 12%. These logs were cut into test samples for the determination of their strength properties. A total of 800 samples (100 samples for each test) free from visible defects were used for each species. Basic physical properties of the samples like moisture content and density were determined. Tensile strength, compressive strength parallel the grain, compressive strength perpendicular to the grain, and bending strength were the mechanical strength tests carried out according to Eurocode 5 (1995) and BS 5268 (2002) specifications on Universal Testing Machine (UTM). Results were analyzed statistically using Statistical Package for Social Sciences (SPSS) while grading was done according to Eurocode 5 (EC5). Cypress was graded into strength class C20 while eucalyptus was graded into strength class D24. Strength class C20 is used in load-bearing structures that require high strength, such as roof trusses and floor systems. D24 is a common structural grade for a variety of structures exposed to high environmental conditions.

Recombinant Keratin-Chitosan Cryogel Decorated with Gallic Acid-Reduced Silver Nanoparticles for Wound Healing.

Wound healing is a complex physiological process that can be roughly divided into four stages: hemostasis, inflammation, proliferation, and remodeling. Conventional wound dressings often fail to meet the diverse needs of these healing stages due to their limited functionality. Cryogels, however, possess several attractive properties, such as large, interconnected pores, good mechanical strength, and ease of modification, making them suitable for developing advanced dressings with multiple functions. In this study, we developed a multifunctional cryogel dressing, with biocompatible polysaccharides as the main component, designed to provide a breathable, moist, and antibacterial microenvironment for chronic infected wounds, thereby promoting wound healing. Recombinant keratin 31 (RK31) was combined with chitosan (CS) to produce a CS/RK31 cryogel, referred to as CK. Gallic acid-reduced silver nanoparticles (GA/Ag NPs) were incorporated as the active antibacterial component to create the CS/K31@GA/Ag cryogel, known as CKGA. The cryogel was characterized using scanning electron microscopy (SEM) and a universal testing machine, and its biocompatibility was assessed in vitro. The dynamic hemostatic performance of the cryogel was evaluated with a rat tail amputation bleeding model. Additionally, the antibacterial effects of the cryogel against Staphylococcus aureus and Escherichia coli were tested using agar diffusion assays and turbidimetry. The antioxidant capacity of the CKGA cryogel was also measured in vitro. Finally, the cryogel's ability to promote wound healing was tested in an SD rat model of infected wounds. Characterization results showed that the CKGA cryogel features an interpenetrating porous network structure and exhibits excellent mechanical properties, with a swelling rate of up to 1800%. Both in vitro and in vivo experiments confirmed that the cryogel has good biocompatibility, effectively absorbs exudates, and rapidly stops bleeding. The addition of GA/Ag NPs provided significant antibacterial effects, achieving an inhibition rate of over 99.9% against both S. aureus and E. coli. Furthermore, CKGA cryogels demonstrated a strong scavenging capacity for ROS in a dose-dependent manner. Studies using the SD rat infected wound model showed that the cryogel effectively inhibited bacterial proliferation on wound surfaces, reduced local tissue inflammation, and promoted the healing of infected wounds. The multifunctional cryogel, with its rapid hemostatic, antibacterial, and antioxidant properties, as well as its ability to promote cell proliferation, could be widely used as a wound dressing for the healing of bacterial infections.

Facile development of flexible cellulose acetate-lead dioxide membrane electrodes for supercapacitor applications

Current work focuses on the development of flexible membranes of cellulose acetate containing lead dioxide for supercapacitor applications. The functionality of cellulose acetate and lead dioxide are analyzed by Fourier transform infrared spectroscopy. The degree of crystallinity is studied using X-ray Diffraction. The degree of hydrophilicity is discussed by water contact angle measurements. A Universal Testing Machine is used to examine the mechanical properties. The electrochemical performances are illustrated using Cyclic voltammetry, Electrochemical impedance Spectroscopy and Galvanostatic charge-discharge techniques. The highest recorded specific capacitance is 148 F g−1 at a current density of 40 mA g−1 for a membrane of 1 wt% lead dioxide in cellulose acetate. Capacitance retention of 89% after 5000 cycles is attained. The power density of 56 W kg−1 and energy density of 10 Wh kg−1 is achieved. The cellulose acetate doped with lead dioxide membranes can provide a better electrode material matrix for flexible energy storage.

Effect of preparation design on fracture resistance of molars restored with occlusal veneers of different CAD-CAM materials: an in vitro study

BackgroundOcclusal veneer had been evaluated for mechanical properties using lithium disillicate. However, studies evaluating the mechanical properties of occlusal veneer with different preparation designs and ceramic materials are lacking. So, this in vitro study aimed to evaluate the fracture resistance of occlusal veneers with two designs fabricated from two different ceramic materials.Material and methodsFourty mandibular third molars were distributed to 2 groups (n = 20) according to preparation design: group (O) anatomical occlusal reduction and group (OA) anatomical occlusal and 1 mm axial reduction. Each group was additionally subdivided into two subgroups (n = 10) according to ceramic materials; in subgroup X, lithium disilicate (e.max CAD, Ivoclar AG, Schaan, Liechtenstein) was used, and in subgroup S, zirconia-reinforced lithium silicate (ZLS) (Vita Suprinity, VitaZahnfabrik, Bad Säckingen, Germany) was used. All specimens were cemented with a light-cure resin cement (Choice 2, Bisco, Schaumburg, USA). 5000 thermocycles were applied to all specimens with both temperatures of 5 °C and 55 °C in two water baths; the dwell time was 30s at each bath, and the transfer time was 10s. Then all specimens were subjected to a fatigue simulation under dynamic loading of 200 N for 250,000 cycles. A universal testing machine (5500R/1123, Instron, Norwood, USA) was used to evaluate the fracture strength with a crosshead speed of 1 mm/min. All data were analyzed statistically by using a two-way ANOVA, and for some violations of assumptions, these results were compared with those obtained by the nonparametric test (Scheirer Ray Hare) (α = 0.05).ResultsA statistically significantly higher fracture resistance in the ‘OA’ (3389 N) compared to the ‘O’ (2787 N) group regardless of the ceramic material (P < .001) and a statistically significantly higher fracture resistance in the ‘X’ (3295 N) compared to the ‘S’ (2881 N) regardless of the preparation design (P = .015).ConclusionsFor occlusal veneers, all preparation designs and materials (such as Vita Suprinity and e.max CAD) had clinically acceptable fracture resistance values that were greater than the maximal biting forces. On the other hand, the e.max CAD with occlusal veneer, including axial reduction design, demonstrated the maximum fracture resistance value. Finally, no relationship between fracture strength and mode of failure was found.

Development and characterization of nitazoxanide-loaded poly(ε-caprolactone) membrane for GTR/GBR applications

ObjectiveGuided tissue/guided bone regeneration (GTR/GBR) membranes are widely used for periodontal bone regeneration, but their success depends on a bacteria-free environment. Systemic antibiotic treatment often proves inadequate, moreover, the increasing prevalence of antibiotic resistance in oral infections exacerbates this challenge. This study aimed to fabricate antibacterial membranes using a new class of antibiotics for local drug delivery, to eradicate infections and promote tissue regeneration. MethodsMembranes loaded with nitazoxanide (NTZ) were fabricated via electrospinning using poly(ε-caprolactone) (PCL) with varying concentrations of NTZ (0 %, 2.5 %, and 5 % w/w) relative to the polymer weight. Morphochemical of NTZ-loaded membranes were assessed using scanning electron microscopy-energy dispersive spectroscopy (SEM-EDS) and Fourier Transform Infrared spectroscopy (FTIR). Mechanical properties were evaluated using universal testing machine and NTZ release profile from membranes was determined by spectrophotometer (λmax = 444) for 14 days. Antimicrobial efficacy against periodontal pathogens, cell compatibility and mineralization were evaluated using periodontal ligament stem cells (PDLSCs). ResultsOptimized spinning parameter maintained a uniform fiber diameter and successful loading of NTZ was confirmed by SEM-EDS and FTIR. NTZ incorporation did not significantly affect mechanical properties, whereas the drug release kinetics showed an initial burst, followed by sustained release over 14 days. NTZ-loaded membranes demonstrated antibacterial activity against Aggregatibacter actinomycetemcomitans (Aa) and Fusobacterium nucleatum (Fn). Importantly, the presence of NTZ showed minimal cell toxicity; however, it reduced the mineralization potential compared with that of the pure PCL membrane, which increased over time. SignificanceTaken together, these findings established that NTZ-loaded membranes could be promising barrier membrane to counteract microbial environment and aid periodontal bone regeneration.

Evaluation of tensile bond strength of two different cements used for luting zirconia coping to one-piece zirconia implant - An in vitro study

Aim: The purpose of this in vitro study was the evaluation of the tensile bond strength of two different cements used for luting zirconia coping to one-piece zirconia implant. Settings and Design: The study was designed in an in vitro study setting. Materials and Methods: A one-piece zirconia implant was scanned on laboratory scanner, and thirty zirconia implants were milled by computer aided manufacturing (CAM). Subsequently, the abutment surface of each zirconia implants were scanned in laboratory scanner and coping with a hole was designed by computer-aided designing software, which was used for milling by computer-aided manufacturing (CAM). After various surface treatments of abutment and intaglio surface of coping, fifteen sets were cemented by glass ionomer cement (Group I) and the other fifteen sets by adhesive resin cement (Group II). All thirty samples after thermocycling were dried and pulled out in a universal testing machine, and tensile retention force is noted in pounds per square inch (psi). Statistical Analysis Used: Values for tensile retention force were tabulated for both the groups. Mean and standard deviation are calculated. Independent t-value and P value were calculated. Results: The least tensile retention force was reported in Group I (165.86 ± 25.74 psi). Maximum tensile retention force was received for Group II (396.81 ± 78.32 psi). Independent t-test was applied from which t-value calculated was 10.85 and P value obtained was 0.001, which means that there exists a very high difference in tensile bond strength of cement in Group I and Group II. Conclusions: Better tensile retention forces were observed in samples cemented with adhesive resin cement when compared to samples cemented with glass ionomer cement.

Evaluation of mechanical properties of natural fiber based polymer composite

Natural fiber based polymer composites are eco-friendly alternatives to synthetic materials, with greater mechanical properties, biodegradability, availability, ease of access, and affordability. Jute fiber is widely recognized as one of the most important and beneficial natural fibers due to its strength, durability, and biodegradability. In this study, the jute composite is designed and fabricated using a 5-layer jute and epoxy resin, utilizing the manual hand lay-up technique. The combination of 52.5 % jute and 47.5 % of epoxy resin and harder is found optimized to achieve the goals of improving the tensile strength and flexural strength, reducing the cost of epoxy resin, and promoting eco-friendliness and sustainability. Tensile testing was performed on a universal testing machine, while flexural testing was done with a three-point bending test. Experimentally, the composites reinforced with jute and epoxy resin were capable of achieving the required levels of tensile strength (42.91 MPa) and bending strength (69.30 MPa). To validate and visualize specimens, numerical analysis was performed on the ABAQUS simulation software. The numerical simulation utilized ASTM D3039 and ASTM D7264 as the specified requirements for tensile and flexural behavior. For validation, these tensile and flexural test results were then numerically analyzed and compared to the experimental data. Finally, composite design, fabrication, and optimization can improve mechanical properties, reduce composite weight, lower resin cost, and increase sustainability. The proposed design and composition can be implemented to achieve lightweight properties in various applications, such as car components, door handle sheets, bicycle seat backs, and luggage covers.

Comparative evaluation of the effect of three different obturation techniques on push-out bond strength of AH Plus Bioceramic and EndoCeramic sealers: An in vitro study

Abstract Context: Effect of three different obturation techniques on bond strength of bioceramic sealers. Aim: This study aimed to investigate the effect of cold lateral compaction, thermafil, and thermoplasticized obturation techniques on the push-out bond strength of AH Plus Bioceramic and EndoCeramic sealers. Settings and Design: The design of the study was an in vitro study. Materials and Methods: Forty-two extracted teeth that were single-rooted and had fully developed apices were chosen, decoronated, and biomechanically prepared using rotary nickel–titanium (NiTi) instruments. Samples were divided into two groups of n = 21. Group 1: AH Plus Bioceramic sealer, Group 2: EndoCeramic sealer. Then, based on the obturation technique employed, each group was divided into three subgroups (n = 7): subgroups 1a, 2a: Cold lateral compaction; Subgroups 1b, 2b: Thermafil; and Subgroups 1c, 2c: Thermoplasticized (obtura). Using universal testing machine, slices from the middle third of the sample’s root were analyzed to determine the push-out bond strength values. Results: Compared to other groups push-out bond strength was noticeably higher for the cold lateral compaction technique with EndoCeramic sealer (Subgroup 2a), followed by the Thermafil technique with EndoCeramic sealer (Subgroup 2b). Conclusions: In the present study, compared to heat-based obturation techniques, cold lateral compaction showed better push-out bond strength values for both sealers. EndoCeramic sealer resulted in greater push-out bond strength values than AH Plus Bioceramic sealer.

Collective effect of reduced graphene oxide and Zn2U hexaferrite filler based epoxy composites on microwave absorption with improved mechanical properties

Herein, we have synthesized Ba4Zn2Fe36O60 (Zn2U) and have produced reduced graphene oxide (rGO) wrapped filler material for the preparation of epoxy composites of different weight percentages (40, 50 and 60 wt %). These rGO wrapped Zn2U hexaferrite filler was analyzed by XRD and SEM to examine the crystal structure and distribution of Zn2U hexaferrite in between/on the surface of rGO respectively. The magnetic and mechanical properties of prepared rGO@Zn2U@epoxy composites were evaluated by employing vibrating sample magnetometer and universal testing machine respectively. The investigation involved analyzing the complex permittivity and permeability, and based on this information, an assessment of the reflection loss was conducted. The results obtained indicate that epoxy composites with a filler content of 60 % rGO@Zn2U have significant promise as an advantageous choice for EMI shielding and microwave absorption applications.

Effect of recycled aggregates with different parent strength and fly ash on flexural strength of recycled aggregate concrete prisms

Fast consumption of conventional ingredients of concrete and waste generated due to demolishing old buildings is a multi-fold problem in the concrete industry. Hence the sustainable alternative of it is the need of the day. In this research work effect of binary blending of demolished waste and fly ash on the flexural strength of plain concrete prism is presented. The properties of aggregates and cement are evaluated. The physical and chemical properties of fly ash were determined. Recycled aggregates from demolished waste with different mix ratios (1:2:4 and 1:1.5:3) were used. Optimization of recycled aggregates; by evaluating concrete cylinders in 12 batches; showed 35% as optimum. At the optimum dosage of recycled aggregates fly ash was used from 2.5% to 15% with an increment of 2.5% to optimize its dosage. Compressive strength test of the standard-size cylinders and their comparison with control concrete showed a 10% dosage of a fly as the optimum percentage to replace the cement in the concrete matrix. Using both optimized dosages of recycled aggregates and fly ash prism specimens of900mmx150mmx300mm were cast in four batches. The beam specimens were cured for 28 days followed by an evaluation of flexural strength and deflection under centric load in the universal testing machine. Test results of flexural strength (only 15% loss) showed good potential for both waste materials in the concrete matrix. Recycled aggregate with higher parent strength showed better performance than its other counterparts. With higher-strength recycled aggregates residual flexural strength was recorded as equal to 93%. For all specimens recorded deflection was within the allowable limits of ACI-318.

The fracture and perforation failure analysis of downhole tubes

：The downhole tubes were fractured and perforated after 5 years of shut-in due to high water cuts. This study employs a comprehensive array of analytical techniques to investigate the mechanisms behind fractures and perforations. Utilizing non-destructive testing (NDT), direct reading spectrometer, tensile strength testing machine, impact testing machine, optical microscope (OM), macroscopic fracture morphology observation, scanning electron microscope (SEM) and energy spectrum analysis (EDS), and sulfide stress corrosion cracking (SSCC) was studied. The reason for the fracture of the tubing is that under the condition of low pH value, high hydrogen sulfide environment, the tubing is fractured due to stress concentration caused by cracks in the outer thread relief groove. The perforation of the inner tube wall was caused by gradual wall thickness reduction under the influence of H2S, CO2, and Cl−, resulting in fouling and eventual perforation. To prevent tube corrosion during long-term shut-in, it is recommended to inject crude oil or diesel into the well.

Design and Test of Potato Seedling Killing and Residual Film Recycling Integrated Machine

Plastic film mulching technology can effectively enhance crop yield and quality, and the use of mulch has been increasing in recent years; however, the problem of mulch residue is worsening due to the large amount of recycling work and slow natural degradation. In this study, a potato seedling killing and residual film recycling machine is designed to provide good working conditions for potato harvesters before harvesting in response to the problems of difficult separation of film tangles, the low net rate of recycling due to the mixing of residual film with soil, and the high soil content in residual film recycling operations in northwest China. The machine is based on the potato monoculture and double row planting mode in Gansu area. This paper puts forward the overall design scheme and carries out the theoretical analysis and parameter determination of the key components, such as the seedling killing device, the film surface cleaning device, the film unloading device, and so on. Using EDEM software to carry out the virtual simulation test and Design-Expert13 to analyze the test results, we determined the optimal working scheme for the machine, with a forward speed of 0.8 m/s, a film gap of 125 mm, and a spiral stirrer speed of 600 r/min. Based on a field test for verification, the test results show that the machine’s residual film recovery rate was 83.3%, the impurity rate was 3.8%, and the rate of injury to the potatoes was 1.4%. The machine meets the requirements of national and industry standards, and it can simultaneously realize straw crushing, film surface cleaning, residual film recycling, and hydraulic film unloading operations, with better operating results and while reaching the expected results. It can also provide a reference for the design and testing of a seeding and residual film recycling machine.

Acoustic Emission Energy Release Rate Model for Classification of Damage Development in Large Fiber Reinforced Plastic Composite Structures

Acoustic emission identification of fracture mechanisms in composite materials is of great importance for the practical assessment of the serviceability of aerospace structures, such as unmanned aerial vehicles, rocket motors, and others. Many scientific research studies conducted in recent decades have demonstrated the unique capabilities of the Acoustic Emission (AE) method to detect and identify different failure mechanisms, including fiber breakage, matrix cracking, and delaminations in fracture tests of composite specimens. However, testing large composite structures, in many cases, can be accompanied by multiple time-overlapped fracture events activated simultaneously, resulting in considerable difficulties in the classification and assessment of combined prolonged AE signals. In this work, we propose the Energy Release Rate (ERR) model for the classification of AE activity related to fiber-reinforced plastic (FRP) composite fracture. The model identifies accurately both micro-scopic and macro-scopic fracture mechanisms in large aerospace structures having complex composition of materials. The model is practically applied using several machine learning methods and provides a simple means to identify and discriminate typical fracture mechanisms and their combinations. Specifically, we describe ERR model, the choice of most informative AE parameters, the choice of suitable machine learning classification methods, their training and testing on FRP specimens, and validating the model in practical tests of large full-size FRP composite structures.

Machine tool cross beam design, fabrication, and testing using metal big area additive manufacturing

This paper describes the application of metal Big Area Additive Manufacturing (mBAAM) to the fabrication of a machine tool cross beam. The replacement of a traditional box design weldment with a new design printed by wire arc additive manufacturing using the MedUSA system at Oak Ridge National Laboratory (ORNL) is detailed. This requires a new design strategy based on the unique mBAAM capabilities. The intent of the new design is to reduce mass, while maintaining the dynamic stiffness. To compare the two designs, the natural frequencies and mode shapes are measured using impact testing and predicted using finite element analysis. It is confirmed that the printed structure dynamics agreed with the numerical model predictions, which demonstrates that it is feasible to model a large-scale mBAAM part and understand its behavior prior to printing. Another notable outcome of this study is that the significant residual stress and distortion in the print indicate that knowledge gaps remain for widespread implementation of mBAAM.

Impact of speed sintering on the mechanical and optical properties of multilayered zirconia

Speed sintering techniques have been introduced to shorten the sintering time of zirconia ceramics, yet their impact on multilayered zirconia properties remains understudied. The purpose of this in vitro study was to assess the effect of speed sintering on the optical properties and the mechanical flexural strength of multilayered zirconia materials. A total of 360 disks (Ø14 ±2 mm ×1.2 ±0.02 mm) were fabricated by following the International Organization for Standardization (ISO) 6872:2015 standard using 2 types of Vita A2 shade multilayered zirconia materials: IPS e.max ZirCAD Prime (ZP) and IPS e.max ZirCAD Prime Esthetic (ZPE). Each material comprised translucent (Tr), gradient l (Gr), and dentin (De) layers, with 60 disks per layer. Half were sintered using a standard sintering protocol and half using a speed sintering protocol. Biaxial flexural strength was accessed using a universal testing machine equipped with the Blue Hill Universal software program by following the ISO 6872:2015 standard, with 20 disks per subgroup. The spectrophotometric analysis of optical properties (contrast ratio [CR], translucency parameter [TP], and total transmittance [Tt%]) was performed using a dual-beam spectrophotometer (Ultrascan VIS) in accordance with the ISO 7491:2000 standard, with 10 disks per subgroup. The comparison of the optical properties and the mechanical flexural strength between the speed and standard protocol was analyzed using an unpaired t test (α=.05). Speed sintering reduced biaxial flexural strength in all ZP layers (P<.05) and in ZPE-Gr (P<.05). A statistically significant difference in the CR was observed in the ZP-Tr, ZP-Gr, and ZPE-Gr layers (P<.05). The TP of the ZP-Gr, ZP-De, and ZPE-Gr layers was significantly lower when using the speed sintering protocol. Tt% was significantly lower with speed sintering for both materials (P<.05). Speed sintering statistically changed both the optical (CR, TP, Tt%) and mechanical (flexural strength) properties of multilayered zirconia materials, but the differences may not be clinically relevant.

Forming limit analysis of magnesium alloy sheet metal forming process at elevated temperatures

Abstract Magnesium alloys are valued by industry for their lightweight structures. Magnesium alloy are mainly produced by warm forming because the sheet formability is poor at room temperature. The mechanical properties of magnesium alloy AZ31, such as stress-strain curves and damage values at different elevated temperatures, were obtained by this study using a computerized screw universal testing machine. Freudenthal fracture criteria were used to obtain the forming limit at distinct temperatures. The forming limit analysis proceeded during the sheet metal forming process at various elevated temperature. The fracture’s forming load, stroke, and position were determined for different working temperatures of the sheet metal forming process for AZ31, using a finite element simulation combined with the ductile fracture criteria. Finally, the predicted values were compared with the experimental results during the sheet metal forming process. The simulation results agreed with the experimental values for the fracture forming load, stroke, and position of the sheet metal forming process. The feasibility of the present method was confirmed to predict forming limit during the sheet metal forming process for different elevated temperatures. A finite element analysis for forming limit prediction would be beneficial to the design of sheet metal processes for AZ31 magnesium alloys.

Effect of nanoparticles reinforcement of silicon dioxide derived from prosopis juliflora on Silver-Grey magnesium nanocomposite: utilization of silicon dioxide mechanical and tribological properties

Abstract The automotive and aviation industries require lightweight materials to enhance working efficiency. Composites combine materials such as aluminium, magnesium, titanium, steel, and copper with various forms of reinforcements to offer lightweight alternatives for a range of applications. The present investigation aims to fabricate a Silver-Grey Magnesium (Mg-25%Si) alloy-based nanocomposite with silicon dioxide (SiO2) nano reinforcement at weight % of 0, 3.25, 6.5 and 9.75 utilizing the two step stir casting method. Prosopis juliflora is utilized in the production of different weight percentages of SiO2 nano reinforcements. The microhardness, tensile, wear, and impact tests are performed on the Silver-Grey Magnesium nanocomposites (Mg-25%Si/SiO2) utilizing a computerized tensometer testing machine, a Vicker’s hardness tester, a pin-on-disc tribometer, and an Izod impact, respectively. The x-ray diffraction (XRD), Field Emission Scanning Electron Microscope (FESEM), and Energy-dispersive x-ray spectroscopy (EDAX) with elemental mapping microstructure were employed to scrutinize the tensile specimen fracture, EDAX, elemental mapping microstructure, wear, CoF, and worn surface characterization and impact strength analysis. When compared to the Silver-Grey Magnesium (Mg-25%Si) base alloy, the results of the Mg-25%Si/SiO2 nanocomposites demonstrated an increase in SiO2 nano reinforcements that significantly increased microhardness, tensile strength, wear resistance, and impact strength. The corresponding values are 113.36 VHN, yield and ultimate tensile strength of 603.25 MPa and 665.84 MPa, 0.00478 mm3 m−1, CoF of 0.38421 and 400 J m−1.

Effect Of Post-Curing Treatment Temperature On The Tensile Strength And Impact Resistance Of Coconut Fiber-Reinforced Polyester Composites

Composite material is an engineered material created by combining two or more materials to produce enhanced mechanical properties compared to its constituent materials. This study focuses on natural fiber composites using coconut fiber as reinforcement with a polyester matrix. Post-curing treatment is applied to improve the mechanical strength of the composite. Post-curing is a heating process at a specific temperature aimed at enhancing the properties of the composite. The purpose of this research is to determine the effect of post-curing temperature on the impact strength of polyester-coconut fiber composites. The specimens were fabricated using the mixing method for material blending and hand lay-up for composite formation, following the standards of ASTM D638-02 Type I and ASTM D256 for impact testing. The specimens were heated in an oven at various temperatures: non-post curing, 110°C, 120°C, and 130°C, each for one hour. Impact testing was conducted using a Mory Testing Machine. The results showed that the composite with a post-curing temperature of 120°C achieved optimum tensile strength of 9.2 N/mm² and impact strength of 0.1663 J/mm². Based on these findings, the polyester-coconut fiber composite can be used as material for particleboard type 100 and meets the SNI 03-2105- 1996 standards for tensile and impact strength. Additionally, this composite has the potential to be used as an alternative material for manufacturing SNI-standard helmet

On Microplasticity-induced Fatigue Fracture and its Relation to Entropy

Abstract The study delves into the intricate effects of microplasticity on fracture formation in testing specimens under axial cyclic loading. The primary aim is to pinpoint the juncture at which microplasticity becomes discernible across the stress cycle. Fatigue tests are conducted on varied specimens until failure using a fatigue testing machine, while recording parameters such as frequency, stress amplitude, applied power, and tensile strain. The investigation seeks to ascertain whether cracks must attain a specific size before manifesting these subtle alterations. A conjectured relationship is proposed between the number of cycles and entropy throughout the process. Additionally, a hypothesis is posited suggesting that microplasticity emerges only once the crack surpasses a certain threshold, such as grain size. This research provides insights into material fracture mechanisms and their implications for product durability and safety. Such discernments into the product life cycle under analogous conditions hold promise for delineating operational limits.