Unburned Hydrocarbons Research Articles

Retrofit of a Marine Engine to Dual-Fuel Methane–Diesel: Experimental Analysis of Performance and Exhaust Emission with Continuous and Phased Methane Injection Systems

Shipping is a highly energy-intensive sector, and fleet decarbonization initiatives can significantly reduce greenhouse gas emissions. In the short-to-medium term, internal combustion engines will continue to be used for propulsion or as electricity generators onboard ships. Natural gas is an effective solution which can be used to mitigate greenhouse gas emissions from the marine sector. Considered to be a transitional fuel, it can provide a potential reduction in CO2 emissions of around 20–30%, compared with conventional marine fuels. This work investigated the influence of diesel-injection strategies on the performance and emissions of a single-cylinder prototype compression-ignition engine for marine applications, retrofitted to run as a Low-Pressure Dual-Fuel Engine using natural gas. Two different injection systems were used: a mass flow controller enabling continuous-mode gas feeding, and a Solenoid-Operated Gas Admission Valve for marine applications, the latter allowing phased natural-gas injection. Experimental tests were focused on partial-load conditions, which are critical for dual-fuel engines, with a natural gas/diesel mass ratio of 4:1. Phased injection resulted in reductions in fuel consumption, compared to continuous mode, of up to 11%. Further experiments demonstrated reductions in fuel consumption of up to 20.7% (in equivalent diesel); on the other hand, the unburned hydrocarbon emissions which resulted were an order of magnitude larger than the reference values for full diesel, reducing the benefits in terms of greenhouse gas emissions, with a reduction in Global Warming Potential of only 3% compared to full diesel.

Technical, economic and environmental assessment and optimization of four hybrid renewable energy models for rural electrification

This work investigates the technical, economic and environmental feasibility of four solar – wind off grid hybrid renewable energy system (HRES) models to provide electrification for Okorobo-Ile town in Andoni Local Government Area of River State, Nigeria using the Hybrid Optimization of Multiple Electric Renewables (HOMER) software. In particular, investigation of the possible inclusion of a fuel cell (FC) system is performed. The four considered models are: pv/wind/battery (PWB); pv/wind/battery/gen-set (PWBG), pv/wind/fuel-cell (PWF) and pv/wind/battery/fuel-cell (PWBF). The best cost-effective configuration among the set of systems were examined for the electricity requirement of 677.75 kWh/day primary load with 99.1 kW peak load. Results obtained showed that the net present cost (NPC) are $615,664.95, $679,348.17, $778,834.22 and $3,534,850.54 respectively for the PWB, PWBG, PWBF and PWF. The cost of energy (COE) was lowest for the PWB with a value of $$0.158 and highest for the PWF with a value of $0.964. The renewable options—PWBF and PWF have higher long-term costs but offer cleaner emissions. In contrast, options with the Diesel-Powered Generator is cost-effective but has a high environmental impact in terms of greenhouse gas emissions and noise pollution. These emissions include 3,758 kg/yr CO2, 23.7 kg/yr CO and a total of 32.67 kg/yr of unburned hydrocarbons, sulfur dioxide, particulate matter and nitrogen oxides. Based on the results, a stand - alone HRES that consist of 166 kW PV panels, 3 wind turbines 29 batteries and 123 kW converter is found to be the best configuration for the village, as it leads to minimum net present cost (NPC) and COE. The PWB system offers the best choice for the community by balancing financial considerations with sustainability which is crucial when making energy system choices. Results also show that while hydrogen, FC system and the electrolyzer can be used together with or without batteries, inclusion of the FC system resulted in the high NPC due to their high cost of investment.

A comparative study of first and second generation biodiesel blends under quaternary injection strategies for enhanced engine performance and reduced emissions

Biodiesel is a promising renewable alternative fuel, offering compatibility with conventional engines without necessitating significant engine modifications. To facilitate the practical integration of biodiesel into engine systems, this study evaluates the performance of two different biodiesel blends (fatty acid methyl ester and hydrogenated catalytic) in a turbocharged inter-cooled diesel engine. The research employs quaternary injection techniques an advanced injection technique, which involve multiple injection events per cycle to enhance engine combustion and emission characterictics of the biodiesel blend fuels and comparing their performance and emission characteristics with those of conventional diesel. Results showed that fatty acid methyl ester biodiesel effectively reduced the CO, UHC, and NOx emissions at lower blend ratios (up to 10 %), with minimal impact on the brake-specific fuel consumption. Conversely, hydrogenated catalytic biodiesel demonstrates notable advantages in reducing fuel consumption with carbon monoxide and particle emissions, particularly for higher blend ratios (20 %), leading to improved indicated thermal efficiency. Additionally, an investigation on higher biodiesel blends under varying early injection timings showed that, optimal fuel efficiency was observed at an early injection timing of −43.6 °CA, accompanied by reductions in total particle number and unburned hydrocarbon emissions albeit with elevated carbon monoxide and nitrogen oxide emissions. These findings suggest that advanced injection strategies combined with sustainable biodiesel blends can significantly improve engine performance and reduce environmental impact, supporting the transition towards cleaner and more efficient transportation fuels.

A Review of Alternative Aviation Fuels

One of the most promising mid-term solutions for reducing GHG emissions from the aviation sector is alternative aviation fuels, especially sustainable aviation fuels (SAFs). Regulations imposed by the Fit for 55 package to use 38% of SAFs until 2050 require a comprehensive analysis of SAFs and production pathway development with increased blending limits of alternative fuel. Within this review, a summary of key aspects of alternative aviation fuels is presented. The review contains a description of the certification process and certified production pathways with an analysis of feedstocks used for SAF production. SAF emissions also have been analyzed based on available research. SAFs reduce particulate matter emissions significantly, even by 70%, compared to fossil fuels. The emission of gaseous exhaust compounds, such as carbon monoxide, unburned hydrocarbons and nitrogen oxides, also is discussed. Alternative aviation fuels have a lower LCA compared to conventional aviation fuel and the LCAs of specific feedstocks are presented.

On the Influence of Engine Compression Ratio on Diesel Engine Performance and Emission Fueled with Biodiesel Extracted from Waste Cooking Oil

Despite the extensive research on biodiesels, further investigation is warranted on the impact of compression ratios on emissions and engine performance. This study addresses this gap by evaluating the effects of increasing the engine’s compression ratio on engine performance metrics—brake-specific fuel consumption (BSFC), power, torque, and exhaust gas temperature—and emissions—unburnt hydrocarbons (HCs), carbon dioxide (CO2), carbon monoxide (CO), nitrogen oxides (NOx), and oxygen (O2)—when fueled with a 20% blend of waste cooking oil biodiesel (WCB20) and petroleum diesel (PD) under various operating conditions. The viscosity of the prepared fuels was measured at 25 °C and 40 °C. Experiments were conducted on a single-cylinder diesel engine under wide-open throttle conditions at three different speeds (1400 rpm, 2000 rpm, and 2600 rpm) and two compression ratios (16:1 and 18:1). The results revealed that at a lower compression ratio, both WCB20 and petroleum diesel exhibited reduced BSFC compared to higher compression ratios. However, increasing the compression ratio from 16:1 to 18:1 significantly decreased HC emissions but increased CO2 and NOx emissions. Engine power increased with engine speed for both fuels and compression ratios, with WCB20 initially producing less power than diesel but surpassing it at higher compression ratios. WCB20 demonstrated improved combustion quality with lower unburnt hydrocarbons and carbon monoxide emissions due to its higher oxygen content, promoting complete combustion. This study provides critical insights into optimizing engine performance and emission characteristics by manipulating compression ratios and utilizing biodiesel blends, paving the way for more efficient and environmentally friendly diesel engine operations.

Enhancing diesel engine performance and emission reduction through hydrogen enrichment in algal biodiesel blends.

The introduction of hydrogen into the engine could enhance its combustion efficiency and emission characteristics. The current study examines the attributes of compression ignition (CI) engines by introducing hydrogen into a biodiesel blend derived from algae. The improved thermal properties of hydrogen, when combined with algae biodiesel, significantly affect the performance, combustion, and emissions of dual-fuel engines. A study was conducted to evaluate the impact of hydrogen enrichment levels of 5%, 10%, 15%, and 20% of the nozzle volume on a biodiesel blend fuel. In comparison to diesel, algal biodiesel reduces emissions of unburned hydrocarbons (HC), carbon monoxide (CO), and oxygen (O2) by 5.19%, 3.61%, and 2.83%, respectively, while increasing nitrogen oxide (NO) emissions by 4.73%. In contrast to biodiesel, diesel demonstrated superior brake thermal efficiency (BTE) and lower specific energy consumption (SEC). Injecting hydrogen into A20 blend fuel at volumes of 5%, 10%, 15%, and 20% results in a respective increase in brake thermal efficiency of 2.65%, 2.97%, 3.50%, and 4.15%. The addition of hydrogen gas to biodiesel blends further enhances their combustion qualities, leading to elevated peak cylinder pressure, temperature, and heat release rate. The results indicate that A20H5, A20H10, A20H15, and A20H20 fuel reduced CO emissions by 3.75%, 8.75%, 12.5%, and 16.25%, respectively, compared to the A20 blend. In the same vein, HC emissions decreased by 5.76%, 10.29%, 15.52%, and 18.98%, respectively, as compared to A20 fuel. However, NO emissions rose by 5.36%, 10.20%, 15.28%, and 23.23%, respectively, for A20H5, A20H10, A20H15, and A20H20 test fuels. Ultimately, the utilization of algal biodiesel and hydrogen enrichment in diesel engines was proven to substantially reduce pollutants while increasing efficiency. This study contributes valuable insights into the intersection of renewable fuels, hydrogen enrichment, and engine technology, with the potential to drive significant advancements in sustainable transportation and environmental conservation.

Evaluation of Aluminum Oxide Nanoparticle Blended with Alcohol Based Biodiesel at Variable Compression Ratios

This paper highlights the use of aluminum oxide nanoparticles as an additive in diesel-butanol blends to show its effect on fuel consumption, emissions and performance. In the present experiment, different concentrations of aluminium oxide nanoadditives (30, 50, and 70 ppm) are used in alcohol-based biodiesel. Butanol has been used in concentrations of 5 and 10 % in diesel and therefore all blends are termed as B5 and B10 in addition to nanoparticle concentration to avoid complexity. These different blends (B5+30, B5+50, B5+70, B10+30, B10+50, B10+70) are tested for various engine loads at a constant speed of 1500 rpm. The experiment was performed on a Variable compression ratio (VCR) engine at varying compression ratios of 16, 17, and 18. Engine characteristics at different compositions of the blend at different compression ratios were provided by the interfaced computer through the software. The enhanced performance effects can be easily seen from the outcomes in the increment in brake thermal efficiency of the blends as compared to neat diesel. Considerable decrement can be observed in carbon monoxide (CO) and unburnt hydrocarbon (HC) values with an increase in compression ratio. Moderate reduction can be observed in NOx at higher loads in contrast to neat diesel.

Optimization of CRDI engine operating parameters using response surface methodology utilizing lemon peel oil biofuel enriched with hydroxy gas

The current study aims to optimize the operational variables of a CRDI engine in Dual-Fuel Mode (DFM). Hydroxy gas (HHO) was generated through water electrolysis using a concentric four-cylinder dry cell electrolyzer with NaOH catalyst, and it was introduced into the inlet manifold as the primary fuel. The pilot fuel consisted of Lemon Peel Oil (LPO) and pure diesel directly injected into the cylinder. An experimental matrix comprising 17 distinct runs was designed using Design of Experiments (DoE), utilizing Box-Behnken Design (BBD) based on Response Surface Methodology (RSM). The RSM model was created depending on the experimental data, and then operating parameters were optimized utilizing the desirability technique. The optimal engine operational variables were identified for the B25 LPO mixture with a constant HHO gas flow rate of 0.5 LPM, a Compression Ratio (CR) of 21.5, an Injection Pressure (IT) of 450 bars, and an inlet air temperature of 87℃. The optimized results were 30.18 % for Brake Thermal Efficiency (BTE), 9.532 g/kW-hr for Carbon Monoxide (CO) emission, 0.253 g/kW-hr for Unburned Hydrocarbon (UHC) emission, and 23.510 g/kW-hr and Nitrogen Oxides (NOx) emission, yielding a total desirability of 0.7641. Empirical validation of the optimized responses at these input conditions demonstrated their conformity to acceptable error ranges.

Phenomenological model for unburned hydrocarbon emissions from spark-ignition, pre-chamber, and dual-fuel internal combustion engines

Considering the strict regulations on the transport sector emissions, predictive models for engine emissions are essential tools to optimize high-efficient low-emission internal combustion engines (ICE) for vehicles. This aspect is of major importance, especially for developing new combustion concepts (e.g. lean, pre-chamber) or using alternative fuels. Among the gaseous emissions from spark-ignition (SI) engines, unburned hydrocarbons (uHC) are the most challenging species to model due to the complexity of the formation mechanisms. Phenomenological models are successfully used in these cases to predict emissions with a reduced computational effort. In this work, uHC phenomenological model approaches by the authors are further developed to improve the model predictivity for multiple variations including engine design, engine operating parameters, as well as different fuels and ignition methods. The model accounts for uHC contributions from piston top-land crevice, wall flame quenching, oil film fuel adsorption/desorption and features a tabulated-chemistry approach to describe uHC post-oxidation. With the support of 3D-CFD simulations, multiple novel modelling assumptions are developed and verified. The model is validated against an extensive measurement database obtained with two small-bore single-cylinder engines (SCE) fuelled with gasoline-like fuel, one with SI and one with pre-chamber, as well as against data from two different ultra-lean large-bore engines fuelled with natural gas (one equipped with a pre-chamber and one dual-fuel with a diesel pilot). The model correctly predicts the trends and absolute values of uHC emissions for all the operating conditions and the engines with an accuracy on average of 11.4%. The results demonstrate the general applicability of the model to different engine designs, the correct description of the main mechanisms contributing to fuel partial oxidation, and the potential to be extended to predict unburned fuel emissions with other fuels.

Study on partial oxidation phenomena of post-injection fuel in diesel engines

In diesel engines, post fuel is injected in the expansion stroke, oxidized by the diesel oxidation catalysts and the high temperature gas re-generates the diesel particulate filters. However, it is empirically known that the post fuel at advanced injection timing is partially oxidized in the cylinder due to the high temperature-pressure conditions and it is a cause of the reduction of fuel consumption. The purpose of this research is to analyze post-injection fuel behaviors in cylinder and investigate the optimum fuel injections that maximize the unburnt hydrocarbons to the diesel oxidation catalysts. The engine employed in this research is a turbo charged 2.0 L four-cylinder DI diesel engine with two fuel injection systems to change the heterogeneity of air-fuel mixture and temperature distributions in cylinder; n-hexane is injected in the intake manifold to produce the homogeneous air-fuel mixture and diesel fuel is directly injected into the cylinder. The partial oxidation ratio of post fuel and the fuel loss mainly by fuel adhesion was calculated by injected fuel quantity, air quantity, and emission data. The 3D-CFD software was introduced to analyze the partial oxidation of post fuel and flow in the cylinder. The heterogeneity of burned gas mixture of post injection atmosphere and the post-injection timings were the parameters of engine tests and 3D-CFD simulations. The results suggest that the heterogeneity of equivalence ratio and the non-uniformity of gas temperature inside the cylinder at the start of post injection affect the partial oxidation of post-injection fuel. The more homogeneous these conditions are, the better the suppression of partial oxidation of post-injection fuel and the avoidance of fuel adhesion to the cylinder wall can be achieved.

A comprehensive analysis of energy, exergy, performance, and emissions of a spark-ignition engine running on blends of gasoline, ethanol, and isoamyl alcohol

This present study showed a comprehensive analysis of energy, exergy, performance, and emission characteristics of a spark-ignition engine powered by blends of gasoline-isoamyl alcohol-ethanol at volume proportions (100_0_0)% (P0E0), (90_5_5)% (P5E5), (80_5_15)% (P5E15), and (70_5_25)% (P5E25) at various engine speeds and compression ratios (CR). The outcomes of thermodynamic analyses revealed that the highest exergy and energy efficiency were 28.92 % (P0E0, 2600 rpm, CR of 9:1) and 31.01 % (P0E0, 2600 rpm, CR of 9:1), respectively. In addition, the average brake power and brake thermal efficiency for P0E0, P5E5, P5E15, and P5E25 increased by (30.36 %, 27 %, 26.74 %, 27.84 %) and (0.34 %, 0.07 %, 0.35 %, 0.33 %) respectively, while brake specific fuel consumption decreased by (2.5 %, 0.64 %, 3.62 %, 6.33 %) in the engine speed range of 2600–3200 rpm. Compared to gasoline, the maximum reduction of carbon monoxide emissions was 6.13 %, 8.81 %, and 9.96 %, while unburnt hydrocarbon emissions exhibited the maximum decrement by 5.8 %, 10.75 %, 12.58 % for P5E5, P5E15, and P5E25, respectively. However, nitrogen oxide (NOx) emissions for P5E25 tended to increase significantly compared to P0E0, while the difference in NOx emissions for P5E15 and P0E0 was marginal. Overall, P5E15 could be considered as the potential alternative fuel for spark-ignition engines towards the goal of sustainable energy conversion.

Toward improving efficiency and mitigating emissions in a natural gas/diesel direct injection dual fuel engine using EGR

As emissions regulations become more and more stringent and conventional fuel sources rarefaction, new alternatives are emerging to address this situation. Dual fuel engines are among the promising solutions, offering both ecological and economic advantages. However, these engines often confront constraints linked to high levels of unburnt hydrocarbons (HC) at low loads and NOx emissions at high loads. To overcome these problems and guarantee high-efficiency overall operating loads, exhaust gas recirculation (EGR) is a potential solution. In the present experimental study, appropriate modifications have been carried out to a single-cylinder diesel engine to ensure dual fuel operation with EGR. Natural gas and diesel are used as the primary and pilot fuel, respectively. At low load operations, the EGR rate is increased up to 35% until the reduction of unburnt hydrocarbons. However, at high loads, the EGR rate is carefully adjusted, as the combustion efficiency easily deteriorates due to oxygen amount lack in the combustion chamber. Also, minimizing NOx emissions is prioritized in all load conditions while keeping thermal efficiency in sight. In addition, the variation in the amount of pilot fuel is studied for improving the combination of dual fuel engine operation with the EGR technique. This made it possible to determine the influence of load, EGR rate, and pilot fuel quantity on the engine in response to the triple challenges of reducing NOx and HC and improving thermal efficiency. The results show that an adequate EGR rate of 30%, depending on the operating conditions, can reduce HC emissions by >25% while increasing thermal efficiency by around 20%. This result is accompanied by a significant reduction, over 90%, in NOx emissions.

Analyzing the influence of feedstock selection in pyrolysis on aviation gas turbine engines: A study on performance, combustion efficiency, and emission profiles

Commercial aviation is primarily reliant on fossil fuels, yet the depletion of these sources and the consequences of climate change necessitates the exploration of sustainable alternatives. The pyrolysis process offers a viable method for producing biofuels from various feedstocks. This research examines the combustion, emission, and performance characteristics of biofuels derived from agricultural residues, waste tyres, and plastics using pyrolysis. Pyrolysis oils derived from forestry or agricultural products exhibit high viscosity and moisture content, which impairs combustion efficiency and increases carbon monoxide (CO) from 70 % to 187 % and unburned hydrocarbon (UHC) emissions. Conversely, pyrolysis oils from plastics and waste tyres provide stable combustion with carbon monoxide and total hydrocarbon emissions (THC) comparable to those of commercial jet fuel. However, nitrogen oxide (NOX) emissions are significantly elevated from 57 % to 157 %. Engine performance tests demonstrated that forestry pyrolysis oils result in thrust loss due to their high viscosity value (14.3–113 mm2/s) and low calorific value (17.3–31.7 MJ/kg). In contrast, plastic and tyre pyrolysis oil perform similarly to commercial jet fuels but may potentially cause performance loss due to their high aromatic content (>47.67 %). Overall, upgrading the viscosity, moisture, and aromatic content of pyrolysis oils can enhance their suitability as alternative aviation fuels. These improvements could assist the aviation sector in achieving its carbon-neutral goals by making pyrolysis oils competitive with conventional jet fuels.

Experimental studies of thermal behavior, engine performance and emission characteristics of biodiesel / diesel / 1 pentanol blend in diesel engine

The present study investigates the significance of the utilization of biodiesel derived from waste cooking oil in diesel engines and its impact on engine output and environmental pollution after blending with diesel and 1-pentanol. The higher values of the ignition index and comprehensive performance index of 4.34 ×10−4mass/min°C2 and 13.71×10−6 mass2/min2 °C3, respectively, for D70B20P10 (70 % diesel, 20 % biodiesel & 10 % 1-pentanol by volume) indicate superior combustion performance. At full load, carbon monoxide and unburned hydrocarbon emissions from 1-pentanol blended fuels decrease significantly, ranging from 40 % to 52 % and 30.76–46.15 % compared to diesel. The D70B20P10 also showed an improved thermal efficiency of 28.68 % among all tested fuels at full load but slightly lower than diesel (29.56 %). Diesel demonstrated superior in-cylinder pressure (ICP) of 77 bar and heat release rate (HRR) of 41.1 J/ºCA owing to its excellent combustion characteristics. Introducing 5–10 % 1-pentanol in blend improved combustion, elevating ICP and HRR, attributed to enhanced fuel atomization and oxygen content. The sustainable process index value obtained for a global index per person is 0.002×10−4cap Litre-1, which lies between 0 and 1, indicates sustainability and compatibility of biodiesel production demonstration by universal biofuels (Andhra Pradesh).

Design and Numerical Analysis of an Annular Combustion Chamber

Designing a combustion chamber for gas turbines is considered both a science and an art. This study presents a comprehensive methodology for designing an annular combustion chamber tailored to the operating conditions of a CFM-56 engine, a widely used high bypass ratio turbofan engine. The design process involved calculating the basic criteria and dimensions for the casing, liner, diffuser, and swirl, followed by an analysis of the cooling sections of the liner. Numerical simulations using NUMECA software and the HEXPRESS meshing tool were conducted to predict the combustion chamber’s behavior and performance, employing the κ-ε turbulence model and the Flamelet combustion model. Methane was used as the fuel, and simulations were performed for three fuel injection angles: axial, 45°, and 60°. Results demonstrate that the combustion chamber is properly dimensioned and achieves complete combustion for all configurations. The pressure ratio is 0.96, exceeding the minimum design criteria. Additionally, the emissions of unburned hydrocarbons are zero, while nitrogen oxides and carbon monoxide levels are below regulatory limits. These findings validate the proposed design methodology, ensuring efficient and environmentally compliant combustion chamber performance.

Effects of using nanosecond repetitively pulsed discharge and turbulent jet ignition on internal combustion engine performance

Robust ignition of hard-to-ignite fuels is essential for future spark ignited internal combustion engines, particularly for introducing efficiency-enhancing diesel-like process parameters like air excess or high amounts of exhaust gas recirculation (EGR). On the one hand, novel plasma-based ignition systems like Nanosecond Repetitively Pulsed Discharge (NRPD) are promising in extending the ignition limits and the early flame development speed. On the other hand, Turbulent Jet Ignition is effective for shortening the combustion duration and decreasing the unburned hydrocarbon emissions.This article investigates experimentally the combination of NRPD ignition and TJI. The aim is to use a technology for robust inflammation (NRPD) in combination with a technology for fast combustion of the bulk charge (TJI). For this purpose, a turbocharged light-duty four-cylinder engine operated with natural gas is used. The engine can be fitted with a classical Open Chamber (OC) spark plug or with Pre-Chambers (PC). The PCs can be filled uniquely with fuel and air coming from the Main Chamber (MC) (“passive PC”), or additional fuel can be added to the PCs (“active PC”). The air-to-fuel ratio and EGR rate can be freely controlled. Five different combustion strategies are investigated with NRPD ignition and compared against an inductive discharge ignition system. The combustion strategies are passive PC with air and EGR dilution, active PC with air dilution, and Open Chamber (OC) with air and EGR dilution. HRR evaluations and a loss analyses are performed to interpret the results.Despite the faster inflammation present with NRPD ignition, similar peak efficiencies and emissions are reached in OC configuration using the inductive discharge and NRPD ignition systems, which are achieved by varying air-to-fuel ratios (AFR) and EGR rates. Above dilution levels for peak efficiency, the efficiency using NRPD ignition decreases at a slower pace and tolerates higher AFR and EGR rates, thanks to a more complete and shorter combustion.For the PC experiments using NRPD ignition, an efficiency increases and a reduction of emissions compared to inductive discharge ignition are present for the investigated AFR and EGR rates for both active and passive PC operations. The efficiency increase is present due to a stronger pre-chamber discharge and thanks to a faster end phase of combustion. Actively fueling the PC results in faster and more complete combustion that is overcompensated by the increased wall heat losses, reducing the overall efficiency. The results show that passive PC with NRPD ignition may be an ideal ignition concept that maximizes engine efficiency and minimizes emissions.

Effect of addition of biodiesel having Karanja oil on exhaust emissions and performance in a diesel engine with hydrogen as a secondary fuel

With a specific end goal to take care of the worldwide demand for energy, broad research is done to create alternative and cost-effective fuel. The fundamental goal of this examination is to investigate the performance, emissions and vibration characteristics of a single cylinder four stroke diesel engine, working in dual fuel mode with biodiesel of Karanja oil ((BKO) as a renewable fuel and hydrogen (H2) as gaseous fuel on low (2%), intermediate between medium-high (53%) and high (69%) load conditions. Biodiesel of Karanja oil as 20% biodiesel and 80% diesel known as BKO20, while 30% biodiesel and 70% diesel known as BKO30. With 25% introduction of gaseous fuel (H2) and biodiesel (10%–40%) along with diesel showed an increase in brake thermal efficiency (BTE), 85.23%, 10.62% and 19.4% respectively as compared to parent diesel fuel operation. As far as emission is concerned, oxides of nitrogen (NOx) decreased on higher load conditions with a variation of biodiesel (10%–50%) in comparison to low load condition. However, the formation of monoxide (CO), carbon dioxide (CO2) and un-burnt hydrocarbon (HC) decreases along with BKO50 using 25% hydrogen fuel substitution at high (69%) load conditions.

Multi-objective optimization of a dual fuel CI engine powered with syngas and pilot diesel using TLBO algorithm: A metaheuristic approach

Abstract The thermochemical conversion of biomass into producer gas presents an attractive alternative fuel option for compression ignition (CI) engines, making biomass gasification a critical driver for achieving sustainable development goals. Considering the application of producer gas (PG) in CI engine, the most potential gases include H2 and CO as main fuel compounds and it is crucial to comprehensively understand the impact of these two gas components on the engine behaviour. Nowadays, artificial intelligence-powered models are frequently applied for simulating engines that run on a single type of fuel. However, their usage is not as common when it comes to modeling dual-fuel CI engines run on synthetic producer gas or syngas. The present study explores the feasibility of optimizing operational parameters, such as engine load and syngas composition, in improving the efficiency and lowering the levels of pollutants emitted by a 3.5 kW CI engine operated under dual fuel (DF) mode using syngas as primary fuel and diesel as pilot fuel. The performance and emission characteristics of syngas (H2:CO) is examined by studying its behaviour in four different combinations. The compositions of syngas are prepared based on the volumetric percentage of the H2 and CO and is inducted into the combustion chamber using a novel venturi-type air-gas mixer. In the present study, an intelligent metaheuristics-based optimization algorithm i.e., Teaching–Learning Based Optimization (TLBO) is developed and introduced, to develop a predictive model within constrained range of engine operating conditions. Further, the algorithm is used to estimate multiple engine performance characteristics simultaneously viz., brake thermal efficiency (BTE), unburned hydrocarbons (HC), and carbon monoxide (CO). The resultant findings identify the optimal engine load of 68.87% and the ideal syngas composition of 63.9% H2 and 49.5% CO as key parameters for maximizing engine efficiency while minimizing exhaust emission. At these optimized operating condition, 19.49% BTE is observed, while HC and CO emission was found to be 384.6 ppm and 445.33 ppm respectively. This shows the effective and efficiency of the proposed algorithm.

The Impact of Incorporating Varying Proportions of Sugar Beet Waste on the Combustion Process and Emissions in Industrial Burner Fuelled with Conventional Diesel Fuel

Abstract The main objective of the case study is to investigate the effectiveness of using solid fuel additives in conventional diesel fuel for industrial furnaces. The study focuses on utilizing agricultural waste derived from sugar beet plant waste as additives to enhance the combustion process and reduce emissions from industrial burners. In this study, experimental measurent for the flame temperatures inside the furnace while altering the proportions of the solid materials have ben achived. The goal was to assess the impact of different loading from these additives on the combustionprocess. Furthermore, the study involved measuring exhaust gases such as carbon monoxide (CO), carbon dioxide (CO2), unburned hydrocarbon (UH), and nitrogen oxides (NOx). The experimental facility arranment allowed the researchers to evaluate the emissions resulting from the combustion process with the addition of solid fuel additives. By measuring these parameters, the study aimed to understand the effect of utilizing agricultural waste as additives on the burning processes and emission formation in industrial furnaces. These findings can contribute to improving the efficiency of combustion processes, reducing emissions, and promoting the utilization of renewable and sustainable fuel sources in industrial settings. In this study, varying the proportions of solid materials used as additives had an impact on the levels of carbon monoxide (CO), carbon dioxide (CO2), and nitrogen oxides (NOx) in the exhaust gases. By increasing the proportion of solid materials in the fuel mixture resulted in changes in the emission levels. The levels of carbon monoxide in the exhaust gases decreased as the proportion of solid materials increased. While the addition of solid fuel additives did contribute to the production of CO2 due to the combustion of the additives, the overall effect on its levels varied depending on the specific proportions used. Also, the levels of nitrogen oxides in the exhaust gases showed different trends depending on the proportions of solid materials used. Typically, increasing the proportion of solid fuel additives led to reduce NOx emissions. However, this may also depend on other factors such as combustion temperature and the composition of the solid materials.

Impact of hydrogen-assisted combustion in a toroidal re-entrant combustion chamber powered by rapeseed oil/waste cooking oil biodiesel

This study investigates the performance and emission characteristics of biodiesel blends of rapeseed oil and waste cooking oil in a toroidal re-entrant combustion chamber (TCC) compression ignition engine. Hydrogen was allowed into the engine in dual fuel mode to enhance the engine performance. The presence of oxygen in the biodiesel and hydrogen induction increased the peak pressure and heat release rate significantly for all the engine loads. At a peak load of 4.88 kW, the maximum brake thermal efficiency (BTE) of 31.77% was recorded for the D70R20W10 (diesel 70%, rapeseed oil 20%, waste cooking oil 10%) biodiesel blend. Furthermore, hydrogen induction enhanced the BTE by around 3%. The biodiesel blending substantially lowered the emissions of unburnt hydrocarbons, carbon monoxide, and smoke opacity. Additionally, hydrogen supplementation facilitated 5–10% carbon monoxide reduction over biodiesel blends by enabling more complete oxidation. However, higher temperatures generated due to complete combustion resulted in more NOx formation. Thus, the authors propose that biodiesel blends of rapeseed oil, waste cooking oil, and diesel with hydrogen induction improve engine performance and reduce regulated emissions.