Forest Habitat Types Research Articles

Multivariate Analysis of the Brinell Hardness of Silver Birch (Betula pendula Roth.) Wood in Poland

An analysis was undertaken of the Brinell hardness of silver birch wood and its dependence on stand location, tree age, tree thickness and forest habitat type, and the interactions between these factors. Wood was obtained from 12 forest districts throughout Poland, from trees aged approximately 30, 50, and 70 years. A total of 51 study plots was established, from which 306 trees were taken. Hardness was measured on three surfaces (transverse, radial, and tangential sections) for 4777 samples, giving a total of 14,331 measurements. It was shown that the hardness of silver birch wood in Poland is significantly influenced by location, tree age, tree thickness, and habitat type, and by interactions between those factors. Habitat type was not shown to affect radial hardness, except in the case of Giżycko forest district. For the whole of the analysed material, the mean hardness on a transverse section was calculated as 66.26 MPa, corresponding to a very hard wood on Mörath’s scale, whereas the values for the longitudinal sections (radial 44.06 MPa, tangential 44.02 MPa) correspond to a soft wood.

Small Mammals in Forests of Romania: Habitat Type Use and Additive Diversity Partitioning

Small mammals are key components of forest ecosystems, playing vital roles for numerous groups of forest organisms: they exert bottom-up and top-down regulatory effects on vertebrate and invertebrate populations, respectively; they are fungus- and seed-dispersers and bioturbators. Therefore, preserving or restoring the diversity of small mammal communities may help maintain the functions of these ecosystems. In Romania, a country with low-intensity forest management and a high percentage of natural forests compared to other European countries, an overview of forest small mammal diversity and habitat type use is lacking, and our study aimed to fill this gap. We also aimed to partition the total small mammal diversity of Romanian forests into the alpha (plot-level), beta, and delta (among forest types) diversities, as well as further partition beta diversity into its spatial (among plots) and temporal (among years) components. We surveyed small mammals by live trapping in eight types of forest across Romania. We found that small mammal abundance was significantly higher in lowland than in mountain forests, but species richness was similar, being associated with the diversity of tree canopy, with the highest values in mixed forests. In contrast, small mammal heterogeneity was related to overall habitat heterogeneity. As predicted, community composition was most distinct in poplar plantations, where forest specialists coexist with open habitat species. Most of the diversity was represented by alpha diversity. Because of strong fluctuations in population density of dominant rodents, the temporal component of beta heterogeneity was larger than the spatial component, but species richness also presented an important temporal turnover. Our results show the importance of the time dimension in the design of the surveys aiming at estimating the diversity of small mammal communities, both at the local and regional scales.

Relative use of xeric boreal habitats by shrews (Sorexspp.)

AbstractFew studies have explicitly examined habitat use by shrews (Sorexspp.) in the boreal forest of western North America. We conducted pitfall trapping in six common xeric habitat types in Yukon, Canada, to determine their relative use by shrews. The overall capture rate was 0.47 shrews per 100 trap nights (TN), with a total sampling effort of 3652 TN. Cinereus shrews (Sorex cinereus; 0.25 per 100 TN) were the most common species, followed by dusky shrews (Sorex monticolus; 0.14 per 100 TN) and American pygmy shrews (Sorex hoyi; 0.08 per 100 TN). Shrew capture rates and species richness was low in all habitat types sampled. Cinereus shrews were captured in similar numbers in boreal mixedwood forest and alpine shrub habitats, and rarely in other lowland forest habitat types. Dusky shrews were captured largely in alpine shrub habitats, while pygmy shrews were captured only in lowland forest habitat types. The relative use of alpine shrub habitat by cinereus shrews and dusky shrews was not expected. Our data was limited by low captures; however, we provide a first approximation of the relative use of common forest types and subalpine shrub habitat in the boreal forest of northwestern Canada.

Diversity and habitat association of medium and large mammals in Gibe Sheleko National Park, Southern Ethiopia.

Complete documentation on the status of mammals is indispensable for appropriate conservation measures in protected areas. However, there is inadequate information on mammalian resources in the ecosystem of Gibe Sheleko National Park (GSNP). Thus, the study aimed to assess species diversity, abundance, and habitat association of medium‐ and large‐sized mammals in GSNP. We stratified the study area into five dominant habitat types, namely dense forest, wooded grassland, grassland, riverine forest, and farmland habitat types based on land cover and vegetation structures and further employed stratified random sampling technique across each habitat type. The sample transects covered 20% of the study area. Transect width ranged from 50 m to 400 m based on vegetation cover and visibility of mammals. The main data were collected via direct observation. Data were analyzed via chi‐square test and species diversity indexes. We recorded the total of 20 mammals species' those belong to 10 families of which 8 species were large‐sized and 12 species medium‐sized mammals. There were two IUCN vulnerable species, namely Hippopotamus amphibious and Panthera pardus, and two globally near‐threatened species, particularly Litocranius walleri and Caracal caracal in the study area. Dense forest held the highest species diversity of medium‐ and large‐sized mammals (H′ = 2.28) with the highest evenness index (J = 0.84). Riverine forest had the least diversity with uneven population distribution. Papio anubis was the most abundance species, whereas Caracal caracal was the least abundant in the study area. GSNP is home for threatened and spectacular mammals species'; hence, an appropriate conservation measure is mandatory to keep existing mammals species'.

Modeliranje višinske in debelinske rasti dominantnih dreves ter ocenjevanje indeksov produkcijske sposobnosti gozdnih rastišč

Modeling the height and diameter growth of trees is an important part of forest management. Growth models provide the basis for determining the thinning regime, target tree dimensions and optimal proportions of developmental phases of forest stands. We developed individual height growth models for dominant Norway spruce (Picea abies (L.) Karst) and European beech (Fagus sylvatica L.) in two forest types (sessile oak-European beech forests and pre-Alpine silver fir-European beech forests). Based on the models, the site productivity index (SPI), defined as the dominant tree height at a diameter of 45 cm, was determined for spruce and beech in both forest types. Based on the diameter increment of the dominant trees, the age of trees in regard to their diameter was calculated, which was the basis for Height-Age modeling. The site productivity index (SPI) of spruce in sessile oak-beech forests and pre-Alpine silver fir-European beech forests is higher than that of beech: 31.3 and 29.7 vs 28.7 and 27.9, respectively. Estimated site indices (SI; dominant tree height at the age of 100 years) in sessile oak- European beech forests and pre-Alpine silver fir-European beech forests were 33.4 and 32.0 for spruce, and 29.0 and 27.0 for beech, respectively. Using the described procedure, it is possible to determine indices of site productivity of spruce and beech (SI and SPI) in the selected forest habitat types. Testing the procedure in other forest types and for other tree species is suggested.

Assessing the conservation status of EU forest habitats: The case of Quercus suber woodlands

In the European Union (EU), there is an urgent need to define a specific and standardized monitoring strategy for Habitat Directive (HD) forest habitats, like Quercus suber woodlands (EU habitat 9330). Such forests are an important component of western Mediterranean landscapes. In Italy, they are undergoing a relevant regression due to the decline of traditional management. Here, we tested the effectiveness of the Cumulative Abundance Profile (CAP) method in assessing the conservation status (CS) of habitat 9330 in central Italy. The CAP method compares plant communities based on their structure and species composition. Our aims were: i) to test the effectiveness of structure and species composition of the tree layer as predictors of different understories and forest habitat types; ii) to compare the results obtained using the CAP method with those deriving from traditional cover-based (CB) vegetation classification; iii) to evaluate the advantages and limitations of using the two methods to assess the CS of EU forest habitats.The similarity between 48 sampling plots was assessed analysing data through the Fuzzy C-Means clustering method. The three groups resulting from the analysis of CAP data corresponded to as many different community types, each highlighting a different CS of the habitat 9330. For the CAP-based groups, the Mantel test showed a significant correlation between the overstory and the understory composition. Besides, the indicator species analysis detected significantly distinct understories in the three groups, and hypsometric curves suggested that each one is related to soils with different fertility. The CB classification (cover data of all species) produced three clusters, too. However, according to the Adjusted Rand index, the agreement between the two classifications was low. When woods have a higher compositional and structural diversity, in CB classification many plots remain unexplained from an ecological, floristic, and conservation point of view. Compositional data, even if essential, resulted insufficient to classify and monitor the CS of highly structurally complex forest habitats. This highlights that the role of structural data in the classification and monitoring of HD forests is underrated, since they resulted to be an important proxy for forest monitoring and management. The CAP procedure could thus represent a viable standardized methodology to assess the CS of forest habitats, together with the analysis of the understory composition. Further studies applying the CAP method in other woody habitats might support the inclusion of this methodology in the guidelines for EU Habitats monitoring.

The Lichen Biota of Pinus sylvestris Under the Impact of Some Stand-Related Factors: A Case Study from the South-Eastern Part of Żerków-Czeszewo Landscape Park (Wielkopolska-Kujawy Lowland)

AbstractA lichenological inventory was conducted in the pine stands in the south-eastern region of Żerków-Czeszewo Landscape Park. The aim of this study was to recognize the lichen species diversity on the bark ofPinus sylvestrisby considering tree age and forest habitat type. In total, 26 species of lichenized fungi were found on the bark ofP. sylvestris. The biota comprises common and widespread species in Poland. Tree age positively and significantly influenced the species richness on the bark ofP. sylvestris. The suitability of the pine tree age for lichens evident as alpha diversity seemed to be independent from the habitat of the trees. The age of phorophytes strongly affected the presence ofHypocenomyce scalaris. Mixed fresh coniferous forests were characterized by higher beta- and gamma diversity compared to fresh coniferous forests. There was no correlation between the number of species per tree (alpha diversity) and diversification of species composition in relation to the distance between pines. The findings indicate that maintenance of a variety of phorophytes and age-diversified tree stands can prevent impoverishment of the lichen biota in the south-eastern part of Żerków-Czeszewo Landscape Park.

An African urban mesocarnivore: Navigating the urban matrix of Durban, South Africa

Urbanisation is rapidly transforming natural habitats with the potential to benefit synanthropic species, especially mesocarnivore species. Knowledge of the spatio-temporal ecology of mongoose species in an urban matrix is limited. Consequently, we examined the home range and habitat use of water mongoose (Atilax paludinosus, n = 14) in an urban matrix landscape. Mongooses were collared and radio-tracked using Global Positioning System (GPS)-Ultra high frequency (UHF) transmitters between July 2018 and October 2019 in the Upper Highway area’s urban matrix, eThekwini Municipality, Durban, KwaZulu-Natal, South Africa. Habitat selection for water mongoose indicated that the species avoided built-up urban areas favouring fragments of forest and bushland habitat types close to natural water sources within the urban mosaic. The adaptability and generalist nature of water mongoose has facilitated their persistence in the urban mosaic. Variability in the home range size and habitat use of individuals of the water mongooses highlights their ability to adapt to anthropogenically modified landscape, yet they were highly dependent on natural refugia in this urban matrix.

Diversity of trees and structure of forest habitat types in Mt. Tago Range, Mindanao, Philippines

Mt. Tago Range in Bukidnon has been subjected to deforestation and forest fragmentation due to logging ca. 35–40 years ago or as direct result of land conversion for agriculture, human settlements and wildlife product harvesting. It is currently not a protected area. This study aimed to provide data on the tree species diversity, structure, composition, conservation status and threats of the forest habitats in the site. Tree survey in the range was conducted in 2018–2019 using thirty-nine 20 x 20 m sampling plots and six one-kilometer transect lines. A total of 1,032 tree individuals from 54 families, 85 genera and 121 species were documented. The site is composed of four tropical forest habitat types namely: lower montane rainforest, upper montane rainforest, mossy-pygmy and forest over ultramafic rocks. These forest habitats also differed in species composition, elevation, substrate, dominance and structure in terms of height and diameter at breast height. The highest diversity index was observed in the mid-elevation and decreasing toward the peak. The diversity pattern herein is attributed to elevation, forest degradation due to anthropogenic activities and nature of habitat. The most abundant families were the Myrtaceae (23%), Podocarpaceae (12.8%) and Fagaceae (12.6%). At the family level the most dominant taxa included the Moraceae (8.7%), Rubiaceae (6.5%) and Myrtaceae (5.8%). Highest importance value index (IVI) in all forest types fell within the range of IVI’s for tropical forests. Assessment of conservation and ecological status revealed that 11 species (8%) are threatened, 28 (22%) Least Concern (LC) and 16 (12%) are Philippine endemics. Threats to tree diversity in Mt. Tago Range included land conversion for agriculture and settlement, illegal logging and lack of legislative protection. The implementation of conservation strategies by stakeholders is recommended to protect the tree species communities and population across the forest habitat types in the site. KEYWORDS: biodiversity, flora, Shannon-Weiner Index, Importance Value Index, non-Protected Area

Diversity of scorpions (Arachnida: Scorpiones) in Polonnaruwa Archaeological Reserve, Sri Lanka

Sri Lanka harbours 20 scorpion species belonging to four families, of which 15 are endemic. The distribution and ecology of scorpion fauna in Sri Lanka is poorly known. In this study, we surveyed the diversity of scorpions in the Polonnaruwa Archaeological Reserve in the dry zone of Sri Lanka. Microhabitats were thoroughly observed using the direct visual encounter method and UV lights from July to November 2018 for about seven hours (19.00–02.00 h) by two to three observers. Species, abundance, age/sex, and microhabitat features were recorded. Diversity indices, including α-diversity and β-diversity, were calculated. Heterometrus swammerdami was the most abundant species recorded, while Isometrus thwaitesi was the rarest. Reddyanus loebli and R. besucheti were common in both open and forest habitat types. Charmus laneus was recorded for the first time in Polonnaruwa. The highest Shannon Index and Margalef Diversity Index values were recorded in open habitats, but species evenness was low compared to forest habitats. Sørensen index values showed a 58% species similarity between two habitats. The results presented here contribute to the knowledge of the diversity of scorpions in these historically significant sites. This can serve as a basis for future research on the impact of habitat modification and fragmentation on populations, distribution and ecology of scorpions.

The Wood of Scots Pine (Pinus sylvestris L.) from Post-Agricultural Lands Has Suitable Properties for the Timber Industry

Scots pine (Pinus sylvestris L.) is a widespread species throughout Europe and at the same time is dominant in Polish forests and of key importance in the wood industry. Pine stands are subjected to numerous environmental stresses, and one of them is the different physico-chemical and biological properties of post-agricultural soils compared to forest soils, which may affect the properties of the resulting wood and its industrial suitability. The research material taken at the height of 1.3 m from tree trunks (breast height diameter, dbh) in the form of sections and discs was collected in an 80-year-old pine stand from four plots, representing former agricultural and ancient forest land, and two types of habitats: fresh coniferous forest and fresh mixed coniferous forest. The forest habitat trophy had a decisive impact on the dendrometric characteristics and properties of pine wood (density, modulus of elasticity, bending strength, and compressive strength along the tracheids). The history of soil use (post-agricultural or forestry) did not affect the analyzed pine wood properties. Regardless of the forest habitat type and soil type history, pine wood at the dbh height showed a variability of features typical of century-old cultivated stands. Individual pine trunks were characterized by significant individual variability.

Water repellency of soils on unpaved roads in coniferous forests

Forest roads play a crucial role in commercial forestry. Most of them are unpaved and exposed to increased surface runoff and the occurrence of soil erosion. Therefore, these roads constantly require repairs and maintenance, which are associated with the high cost of earthworks. Soil water repellency causes retardation of water infiltration into soil, which affects the generation of surface runoff, leading to the destruction of the active road layer. This phenomenon is well recognized in forest habitat soils, but poorly investigated in terms of soils constituting roads and communication routes. Therefore, the aims of this research were to determine the severity and persistence of potential water repellency in the case of soil collected from two unpaved roads in coniferous forest and to investigate the dependence between the severity of soil water repellency and its persistence. Soil samples (Dystric Brunic Arenosols) were collected from three points of the roadway, i.e., centre line, rut and roadside, from two different sites located in fresh coniferous and fresh mixed coniferous forest (Poland). The severity of soil water repellency was assessed, based on measured values of the wetting contact angle (Wilhelmy plate method) and the critical and 90° surface tensions. For this purpose, contact angle measurements of the solid phase, wetted by water–ethanol mixtures, were used and data results were analysed using the Zisman approach. The persistence of potential soil water repellency was assessed using the water drop penetration time test. The severity and persistence of soil water repellency depend on the forest habitat type surrounding the road and point locations on the road cross section. The soil samples collected from the roadside were more water repellent than samples taken from the centre line or rut. A strong relationship was found between the water drop penetration time and the advancing contact angle, the critical surface tension and the 90° surface tension.

Very high-resolution true color leaf-off imagery for mapping Taxus baccata L. and Ilex aquifolium L. understory population

According to the “Habitat” Directive 92/43/EEC, the conservation status of natural habitats depends on the occurrence of populations of their typical species. For some forest habitats, typical species do not occur as canopy dominant trees but are found in the understory. This is the case with the priority habitat ’‘Apennine beech forests with Taxus and Ilex’’ 9210*. Taxus baccata L. and Ilex aquifolium L. are evergreen tree species and occur as isolated trees or groups in the understory of beech dominated forests. Accordingly, the knowledge of the spatial pattern of populations of typical species is fundamental for habitat monitoring goals. In this perspective, this study aims to evaluate the potential of very high-resolution, true color, leaf-off imagery (pixel size = 0.11 m), supplied by Google Earth, for mapping these populations. Understory layer detection has been accomplished through an object-oriented approach, based on multiresolution segmentation. The classification was developed with thresholds based on spectral and geometric properties, as well as on textural and contextual information. The main critical issues are represented by site conditions, where shadowing can prevent crown detection. The thematic accuracy of the target species map resulted in a Producer Accuracy of 0.77 and a User Accuracy of 0.80. The proposed procedure offers a good methodological foundation with which to map the actual spatial extent of forest broadleaved deciduous habitat types, characterized by low abundance and patchily distributed populations of yew and holly.

Variation in Deadwood Microsites in Areas Designated under the Habitats Directive (Natura 2000)

The continuing decline in biodiversity presents a major environmental protection challenge. The conservation of sufficiently extensive and diverse habitats requires an array of coordinated actions, often involving large areas. While a set of conservation objectives have been defined for the Natura 2000 network, no universal methods of accomplishing them have been specified, and so they must be designed by individual Member States. Deadwood volume and the density of large deadwood pieces are widely used for evaluating the quality of forest habitat types designated under the Habitats Directive. In the present study, data from 5557 sample plots were used to evaluate the mean values of the two deadwood indicators as well as the ratio of deadwood volume to living tree volume for each of the 13 habitat types in Poland. In addition, a logistic regression model was constructed to evaluate the effects of terrain, site, and tree stand characteristics as well as protection type on deadwood volume in Natura 2000 areas. Mean deadwood volume varied greatly between habitat types, with the lowest values found for Central European lichen Scots pine forests (91T0–2.5 m3 ha−1) and Old acidophilous oak woods (9190–4.4 m3 ha−1), and the highest for Riparian mixed forests (91F0–43.1 m3 ha−1) and Acidophilous Picea forests of the montane to alpine levels (9410–55.4 m3 ha−1). The ratio of deadwood volume to living tree volume ranged from approx. 1%–17%. Additionally, the presence of large deadwood differed among habitat types: in some, there were no deadwood pieces with a diameter of ≥50 cm, while their maximum density was 6.1 pieces ha−1. The logistic regression model showed that the likelihood of a habitat type to have a ‘favorable conservation status’ as defined by deadwood abundance (a threshold of at least 20 m3 ha−1 according to Polish manuals on habitat type evaluation) increased with sample plot elevation, site fertility, and moisture, as well as stand age and volume. Positive effects were also observed for forests under strict and active protection versus managed forests. Planned efforts are necessary to enhance the quality of habitats with insufficient deadwood, especially in managed forests. Special attention should be given to areas that are readily accessible due to gentle terrain and low site moisture. Furthermore, younger stands on less fertile sites may require intervention to promote deadwood accumulation. We recommend retaining a certain proportion of mature stands until natural death and decomposition. Increasing the density of large deadwood is currently one of the most pressing conservation needs in most habitat types.

Vegetation structure governs nest predation in three types of conifer forest habitats

Vegetation structure governs nest predation in three types of conifer forest habitats

Multi-Factorial Load Analysis of Pine Sawlogs in Transport to Sawmill

This study analyzed the variability of truckloads of large-sized pine logs transported to a furniture manufacturing mill, depending on the origin of the timber, delivery period, length of the transported logs, volume of the load and its mass. It was assumed that the volume and mass of the transported timber load depends on the season of the year and the origin of the timber, which has a significant impact on the mass of one cubic meter of the load. The analysis of the wood origin parameters (location of its growth) took into account the type of forest habitat, soil type and stand abundance. The characteristics of the tree parameters from which the roundwood was obtained took into account age, diameter at breast height (DBH) and height of the stand. The origin of the timber was determined for 1063 timber loads from 40 forest districts transported over a 12 month period. We obtained an average timber load volume of 29.34 m3 which includes single shipments differing significantly in their volume of between 24.21 and 36.51 m3. The origin of the timber, habitat conditions and stand parameters of the harvesting site influence load mass and the mass of 1 m3 of load. The delivery date has an impact on the studied elements of the sawlogs load, with two similar periods—spring and summer. The volume of the transported timber is already at a stabilized level in accordance with legal regulations, which is no longer dependent on other factors and only on the accepted conversion factors for roundwood density and the mass of the empty vehicle set. This has not influenced a reduction in the mass of the transported timber.

Diversity of butterflies in different habitat types of Seethawaka wet zone botanic gardens and Indikadamukalana forest reserve of Sri Lanka

Botanic gardens, forest reserves and other protected areas are established to conserve biodiversity. The present study was conducted to assess the butterfly diversity in a recently established botanic garden of Sri Lanka, the Seethawaka Wet Zone Botanic Gardens (SWZBG) and Indikadamukalana Forest Reserve (IMFR) adjacent to the garden. Three different habitat types within the botanic gardens, the undisturbed forest habitat within the forest reserve and the buffer zone between the Botanic Gardens and Forest Reserve were investigated for butterflies. Butterfly species richness, diversity, endemic species, family composition in different habitats and effects of habitat parameters on butterfly distribution were assessed. Butterflies were collected from five habitats – grassland, shrub, disturbed forest, undisturbed forest, buffer zone, of the SWZBG and IMFR using transect line method with hand netting and fruit baited traps. Collected butterflies were identified using published field guides. Climate and soil parameters of each habitat were measured using standard methods and equipment. Differences of habitat parameters between habitats were estimated using One-Way Analysis of Variance and Tukey’s Multiple Comparison method and butterfly diversity and evenness in different habitat types were assessed using Shannon-Weiner diversity index. The study revealed seventy-nine butterfly species from SWZBG and IMFR highlighting the importance of the sites for safeguarding and conservation of butterflies. Species richness and diversity of butterflies was highest in the buffer zone and lowest in the grassland habitat. The most common butterfly family in the study sites was family Nymphalidae. Endemic species were high in the forest habitat types. Significant differences were evident in habitat parameters between habitat types indicating their effect on butterfly species richness and diversity. The study revealed SWZBG and IMFR as important areas for butterfly occurrence when compared with similar botanic gardens and forest reserves elsewhere in the world.

Spatial pattern of carbon mangrove stock based on habitat characteristics in Bali Province

Although climate change mitigation regarding mangrove forest management has been given significant international attention during the past decade, there are no sufficiently reliable data to quantify the availability of carbon stock in mangrove forests. The mangrove forest in the Bali Province is divided into three habitat types, namely an open bay located in the West Bali National Park, a semi-closed bay located in Tahura Ngurah Rai and a small island in the protected forest of Nusa Lembongan. The objective of this study is to analyse the relationship between carbon stock characteristics of mangrove forests with the different types and morphologies of mangrove forest habitats. Biomass calculations were carried out by using the allometric formula. However, the similar allometric equations produced varying accuracies at different locations. Results revealed that the mangrove forest carbon stock for the semi-closed bay habitat has the highest estimation value of 51.35 tons/ha and a positive relationship pattern of 60 %. On the contrary, the lowest carbon stock value is the open bay beach with a value 26.28 tons/ha and positive relationship pattern of 48 %. This study reveals that each type of mangrove forest habitat has its own living ecosystem characteristics that affect the carbon stock value.

Potential forest fire risk evaluation in Poland

Abstract The term forest fire risk means the existence of such conditions that would make possible the occurrence of a fire in the forest environment. The base for the effectiveness of a forest fire protection system is the evaluation of the forest fire risk followed by adequate organization of the system. This article presents methods for determination of the forest susceptibility to fire known as potential forest fire risk. The below presented methods were developed by Forest Research Institute as the results of the projects commissioned by the General Directorate of State Forests. The forest fire risk category and stand flammability classes are the methods included here. The forest fire risk category was elaborated already in 1975 for the first time. Until today, after the last modification in 2008, it is the fundamental document for the polish forest fire protection system. The purpose of this modification was to increase the determination accuracy of the fire risk category of all polish forest, regardless of its ownership type and at the different administrative level. The categorization method, however, doesn’t reflect the fire risk in micro scale. The attempt to solve that problem was made in 2018 while developing the methodology of stand flammability classes. It was assumed that ground cover fuel models will be developed for the most flammable forest habitat types including ground cover types, dominant species, age class and geographical localisation.

Exploring the visual world of fossilized and modern fungus gnat eyes (Diptera: Keroplatidae) with X-ray microtomography

Animal eyes typically possess specialized regions for guiding different behavioural tasks within their specific visual habitat. These specializations, and evolutionary changes to them, can be crucial for understanding an animal's ecology. Here, we explore how the visual systems of some of the smallest flying insects, fungus gnats, have adapted to different types of forest habitat over time (approx. 30 Myr to today). Unravelling how behavioural, environmental and phylogenetic factors influence the evolution of visual specializations is difficult, however, because standard quantitative techniques often require fresh tissue and/or provide data in eye-centric coordinates that prevent reliable comparisons between species with different eye morphologies. Here, we quantify the visual world of three gnats from different time periods and habitats using X-ray microtomography to create high-resolution three-dimensional models of the compound eyes of specimens in different preservation states—fossilized in amber, dried or stored in ethanol. We present a method for analysing the geometric details of individual corneal facets and for estimating and comparing the sensitivity, spatial resolution and field of view of species across geographical space and evolutionary time. Our results indicate that, despite their miniature size, fungus gnats do have variations in visual properties across their eyes. We also find some indication that these visual specializations vary across species and may represent adaptations to their different forest habitats. Overall, the findings demonstrate how such investigations can be used to study the evolution of visual specializations—and sensory ecology in general—across a range of insect taxa from different geographical locations and across time.