Three-dimensional Particle Image Research Articles

A method for three-dimensional interfacial particle image velocimetry (3D-IPIV) of an air–water interface

A new stereoscopic method for collecting particle image velocimetry (PIV) measurements within ∼1 mm of a wavy air–water interface with simultaneous measurements of the morphology of the interface is described. The method, termed three-dimensional interfacial particle image velocimetry (3D-IPIV), is tested in a wind wave channel with a wind speed of 5.8 m s−1, water depth of 10 cm and a fetch of ∼9 m. Microscale breaking waves populate the interface and their flow patterns are clearly visible in the velocimetry results. The associated capillary waves and surface divergence patterns are observed. Several statistical measurements of the flow are compared with independent measurements and good agreement is found. The method shows great promise for investigating the transfer of momentum, heat and gases across an air–water interface, both in the laboratory and in field settings. Additional methods are described for manufacturing the flow tracers needed for the 3D-IPIV method. These tracers are likely to be useful for other researchers, and have the characteristics of being fluorescent, neutrally buoyant, non-toxic, monodisperse, inexpensive and easy to manufacture.

Twin-Fluid Atomization and Novel Lifted Swirl-Stabilized Spray Flames

The effects of swirl configuration and airflow distribution on the structure of swirl-stabilized spray flames are investigated in a combustor featuring a twin-fluid fuel atomization nozzle, coannular airstreams, and helical-vane swirl assemblies. The flames investigated are similar to those employed in gas turbine combustion engines. A novel lifted swirl-stabilized spray flame, obtained with a particular set of experimental conditions, is described. Three-dimensional particle image velocimetry data are used to analyze the structure of the airflow associated with the lifted flame. The lifting effect is shown to result from an interaction between the atomization airstream and the recirculation zone in the flow, which creates two distinct recirculation regions. Only the larger far-field recirculation zone is able to stabilize combustion effectively, and the structure of the airflow is found to determine the regions of heat release associated with the flame. Detailed information on the structure and characteristics of the fuel spray, obtained using phase-Doppler particle analysis, is also presented. The twin-fluid atomization approach is shown to provide effective atomization over a wide range of operating conditions, while simultaneously allowing a great degree of control over the flame structure.

Electrohydrodynamic flow in a wire-plate non-thermal plasma reactor measured by 3D PIV method

This work was aimed at measurements of the electrohydrodynamic (EHD) secondary flow in a non-thermal plasma reactor using three-dimensional particle image velocimetry (3D PIV) method. The wide-type non-thermal plasma reactor used in this work was an acrylic box with a wire discharge electrode and two plate collecting electrodes. The positive DC voltage was applied to the wire electrode through a 10 MΩ resistor. The collecting electrodes were grounded. The voltage applied to the wire electrode was 28 kV. Air flow seeded with a cigarette smoke was blown along the reactor duct with an average velocity of 0.6 m/s. The 3D PIV velocity fields measurements were carried out in four parallel planes stretched along the reactor duct, perpendicularly to the wire electrode and plate electrodes. The measured flow velocity fields illustrate complex nature of the EHD induced secondary flow in the non-thermal plasma reactor.

ENGINEERING IMAGING: USING PARTICLE IMAGE VELOCIMETRY TO SEE PHYSIOLOGY IN A NEW LIGHT

1. Despite the array of sophisticated imaging techniques available for biological applications, none of the standard biomedical techniques adequately provides the capability to measure motion and flow. Those techniques currently in use are particularly lacking in spatial and temporal resolution. 2. Herein, we introduce the technique of particle image velocimetry. This technique is a well-established tool in engineering research and industry. Particle image velocimetry is continuing to develop and has an increasing number of variants. 3. Three case studies are presented: (i) the use of microparticle image velocimetry to study flow generated by high-frequency oscillatory ventilation in a human airway model; (ii) the use of stereoparticle image velocimetry to study stirred cell and tissue culture devices; and (iii) a three-dimensional X-ray particle image velocimetry technique used to measure flow in an in vitro vascular flow model. 4. The case studies highlight the vast potential of applying the engineering technique of particle image velocimetry and its many variants to current research problems in physiology.

The study for particle image velocimetry system based on binocular vision

In this paper, a new matching model is integrated into standard techniques of three-dimensional (3D) particle image velocimetry (PIV) based on the binocular vision. A 3D space is first segmented and aligned to 2D planes. Then the 2D PIV method or the particle tracking velocimetry (PTV) method is applied to match particles within different interrogation windows. Using the proposed algorithm, problems on spatial stereo matching and information representation can be solved. At last, the algorithm is applied to the real and synthetic particle images, and the results are analyzed. These experiments demonstrate that the proposed approach is effective and practical.

Measurement of turbulent flow phenomena for the lower plenum of a prismatic gas-cooled reactor

Mean velocity field and turbulence data are presented that measure turbulent flow phenomena in an approximately 1:7 scale model of a region of the lower plenum of a typical prismatic gas-cooled reactor (GCR) similar to a General Atomics design (Gas-Turbine-Modular Helium Reactor). The data were obtained in the Matched-Index-of-Refraction (MIR) facility at Idaho National Laboratory (INL) and are offered as a benchmark for assessing computational fluid dynamics (CFD) software. This experiment has been selected as the first Standard Problem endorsed by the Generation IV International Forum. The primary objective of this paper is to document the experiment and present a sample of the data set that has been established for this standard problem. Present results concentrate on the region of the lower plenum near its far reflector wall (away from the outlet duct). The flow in the lower plenum consists of multiple jets injected into a confined crossflow—with obstructions. The model consists of a row of full circular posts along its centerline with half-posts on the two parallel walls to approximate flow scaled to that expected from the staggered parallel rows of posts in the reactor design. Posts, side walls and end walls are fabricated from clear, fused quartz to match the refractive index of the mineral oil working fluid so that optical techniques may be employed for the measurements. The benefit of the MIR technique is that it permits optical measurements to determine flow characteristics in complex passages and around objects to be obtained without locating intrusive transducers that will disturb the flow field and without distortion of the optical paths. An advantage of the INL system is its large size, leading to improved spatial and temporal resolution compared to similar facilities at smaller scales. A three-dimensional (3D) particle image velocimetry (PIV) system was used to collect the data. Inlet-jet Reynolds numbers (based on the hydraulic diameter of the jet and the time-mean average flow rate) are approximately 4300 and 12,400. Uncertainty analysis and a discussion of the standard problem are included. The measurements reveal complicated flow patterns that include several large recirculation zones, reverse flow near the simulated reflector wall, recirculation zones in the upper portion of the plenum and complex flow patterns around the support posts. Data include three-dimensional PIV images of flow planes, data displays along the coordinate planes (slices) and presentations that describe the component flows at specific regions in the model.

Three-dimensional particle imaging by defocusing method with an annular aperture

We propose an annular-aperture-based defocusing technique for three-dimensional (3D) particle metrology from a single camera view. This simple configuration has high optical efficiency and the ability to deal with overlapped defocused images. Initial results show that an uncertainty in depth of 23 microm can be achieved over a range of 10 mm for macroscopic systems. This method can also be applied in microscopy for the measurement of fluorescently doped microparticles, thus providing a promising solution for 3D flow metrology at both macroscales and microscales.

Experimental and numerical investigation of inertial particle clustering in isotropic turbulence

This paper presents the first detailed comparisons between experiments and direct numerical simulations (DNS) of inertial particle clustering in nearly isotropic ‘box turbulence’. The experimental system consists of a box 38cm in each dimension with fans in the eight corners that sustain nearly isotropic turbulence in the centre of the box. We inject hollow glass spheres with a mean diameter of 6 μm and measure the locations of several hundred particles in a 1 cm3volume in the centre of the box using three-dimensional digital holographic particle imaging. We observe particle concentration fluctuations that result from inertial clustering (sometimes called ‘preferential concentration’). The radial distribution function (RDF), a statistical measure of clustering, has been calculated from the particle position field. We select this measure because of its relevance to the collision kernel for particles. DNS of the equivalent system, with nearly perfect parameter overlap, have also been performed. We observe good agreement between the RDF predictions of the DNS and the experimental observations, despite some challenges in the interpretation of the experiments. The results provide important guidance on ways to improve the measurement.

Three-dimensional synchrotron x-ray particle image velocimetry

There is great potential to vastly improve biological flow measurement by using a combination of synchrotron imaging and the latest experimental flow measurement techniques. In the current paper, the three-dimensional velocity field within a cylindrical tube is measured using a combination of phase-contrast x-ray imaging and particle image velocimetry (PIV). We greatly refine the techniques previously used to undertake velocity measurements with a synchrotron light source, substantially enhancing accuracy. Furthermore a PIV correlation peak analysis is developed to allow three-dimensional measurement of the velocity field.

EHD flow measured by 3D PIV in a narrow electrostatic precipitator with longitudinal-to-flow wire electrode and smooth or flocking grounded plane electrode

In this work, results of three-dimensional (3D) Particle Image Velocimetry (PIV) measurements of the electrohydrodynamic (EHD) flow velocity fields in a narrow electrostatic precipitator (ESP) with a longitudinal-to-flow placed wire electrode are presented. The ESP was a narrow transparent acrylic box (90 mm×30 mm×30 mm). The electrode set consisted of a single wire discharge electrode and two plane collecting electrodes. Either two smooth stainless-steel plates or two stainless-steel plane meshes with nylon flocks were used as the collecting electrodes. The 3D PIV measurements were carried out in two parallel planes, placed longitudinally to the flow duct. The positive DC voltage of up to 9.5 kV was applied to the wire electrode through a 10 MΩ resistor. The collecting electrodes were grounded. The measurements were carried out at a primary flow velocity of 0.5 m/s. Obtained results show that the flow patterns for the smooth-plate electrodes and for the flocking plane electrodes are similar in the bulk of the flow. However, the flow velocities near the flocking plane electrodes are much lower than those near the smooth-plate electrodes. This is a beneficial phenomenon, because the lower the flow near the collecting electrodes, the lower re-entrainment of the particles deposited on the collecting electrodes occurs.

An investigation of the flow characteristics in the bootdeck region of a scale model notchback saloon vehicle

The results of an experimental investigation of the bootdeck flow structure of a 36 per cent scale model notchback car are presented together with a general review of advanced laser diagnostic techniques suitable for large-scale wind tunnel flow measurement. The tests were used to characterize the flow behaviour over the Reynolds number range 0.74 × 106-4.93 × 106 in the Cranfield University 2.4 m × 1.8 m wind tunnel. The experiments involved flow visualization, rear bootdeck and backlight three-dimensional stereoscopic particle image velocimetry (PIV) measurements, and mean static and unsteady static pressure measurements. Initial results from the flow visualization suggested flow asymmetries originating in the backlight region that were sensitive to the Reynolds number. The PIV data and static pressure data, however, showed little or no sensitivity of flow to Reynolds number with consistent flow structure and levels of unsteadiness from the backlight to the rear bootdeck region. At this stage no definitive reasons can be given for the discrepancies between the flow visualization and the other data, although the flow visualization data were particularly difficult to interpret near the backlight, and the near-wake structure may be bi-stable in this Reynolds number range. More detailed three-dimensional stereoscopic, time-resolved PIV flow data are now planned to quantify conclusively the correct flow structure and its sensitivities.

Laser-based volumetric colour-coded three-dimensional particle velocimetry

We present a method of three-dimensional particle velocimetry with a single digital colour camera using multiple colour illumination to encode image depth over a large volume. A copper vapour laser operating at 511 nm is used to pump an optical fibre producing a multiple-wavelength beam via multiple order stimulated Raman scattering. The beam is dispersed and formed into a stack of thin sheets to illuminate a volume of space. The spatial co-ordinates of particles imaged within the illuminated volume are obtained from their imaged x , y positions with depth discerned from particle hue (set by the wavelength of illumination). The method exhibits an RMS depth error of 3% in relation to the thickness of the illuminated region. This paper reports a proof-of-principle of three-dimensional particle imaging using a multi-wavelength laser source with a view to 3D-3C particle velocimetry.

Study of axial velocity in gas cyclones by 2D-PIV, 3D-PIV, and simulation

The axial velocity distribution in a gas cyclone has been examined with two-dimensional particle image velocimetry (2D-PIV) and three-dimensional particle image velocimetry (3D-PIV) experiments in this study. Due to the limitation of 2D-PIV configuration, the contamination generated by the strong tangential velocity in the cyclone can be registered in the axial velocity detected by 2D-PIV. Efficient methods are proposed in this work to remove this contamination. The contamination-removed 2D-PIV data agree well with 3D-PIV results. The distributions of the axial velocity are also computed by the Reynolds stress model (RSM) and verified using the PIV experimental results. Reasonable agreements are obtained.

Fluid Dynamic Assessment of Three Polymeric Heart Valves Using Particle Image Velocimetry

Polymeric heart valves have the potential to reduce thrombogenic complications associated with current mechanical valves and overcome fatigue-related problems experienced by bioprosthetic valves. In this paper we characterize the in vitro velocity and Reynolds Shear Stress (RSS) fields inside and downstream of three different prototype trileaflet polymeric heart valves. The fluid dynamic differences are then correlated with variations in valve design parameters. The three valves differ in leaflet thickness, ranging from 80 to 120 mum, and commisural design, either closed, opened, or semi-opened. The valves were subjected to aortic flow conditions and the velocity measured using three-dimensional stereo Particle Image Velocimetry. The peak forward flow phase in the three valves was characterized by a strong central orifice jet of approximately 2 m/s with a flat profile along the trailing edge of the leaflets. Leakage jets, with principle RSS magnitudes exceeding 4,500 dyn/cm(2), were observed in all valves with larger leaflet thicknesses and also corresponded to larger leakage volumes. Additional leakage jets were observed at the commissural region of valves with the open and the semi-open commissural designs. The results of the present study indicate that commissural design and leaflet thickness influence valve fluid dynamics and thus the thrombogenic potential of trileaflet polymeric valves.

Application of three-dimensional hybrid stereoscopic particle image velocimetry to breaking waves

A new technique of three-dimensional hybrid stereoscopic particle image velocimetry (3D hybrid SPIV) for measuring a volumetric spatial distribution of three-dimensional velocity is presented in this paper. The accuracy and uncertainty of this technique are examined by numerical tests. The 3D hybrid SPIV has been found to be able to measure major features of velocity field involving a vortex with turbulence in a shear flow. This technique is used for measuring an instantaneous three-dimensional flow structure under breaking waves. The formation of the three-dimensional vortex structures involving roller and longitudinal vortices in breaking waves is investigated in this study.

A fluid dynamics approach to bioreactor design for cell and tissue culture

The problem of controlling cylindrical tank bioreactor conditions for cell and tissue culture purposes has been considered from a flow dynamics perspective. Simple laminar flows in the vortex breakdown region are proposed as being a suitable alternative to turbulent spinner flask flows and horizontally oriented rotational flows. Vortex breakdown flows have been measured using three-dimensional Stereoscopic particle image velocimetry, and non-dimensionalized velocity and stress distributions are presented. Regions of locally high principal stress occur in the vicinity of the impeller and the lower sidewall. Topological changes in the vortex breakdown region caused by an increase in Reynolds number are reflected in a redistribution of the peak stress regions. The inclusion of submerged scaffold models adds complexity to the flow, although vortex breakdown may still occur. Relatively large stresses occur along the edge of disks jutting into the boundary of the vortex breakdown region.

Three-dimensional particle imaging by wavefront sensing

We present two methods for three-dimensional particle metrology from a single two-dimensional view. The techniques are based on wavefront sensing where the three-dimensional location of a particle is encoded into a single image plane. The first technique is based on multiplanar imaging, and the second produces three-dimensional location information via anamorphic distortion of the recorded images. Preliminary results show that an uncertainty of 8 microm in depth can be obtained for low-particle density over a thin plane, and an uncertainty of 30 microm for higher particle density over a 10 mm deep volume.

EHD flow in a wide electrode spacing spike–plate electrostatic precipitator under positive polarity

In this work, results of two- and three-dimensional particle image velocimetry (PIV) measurements of the flow velocity fields in a wide spacing spike–plate electrostatic precipitator (ESP) under positive polarity are presented. A DC voltage of positive polarity (up to 28 kV) was applied to the spike electrode. The average gas flow velocity was 0.6 m/s. The PIV measurements were carried out in four planes perpendicular to the plate electrodes. Three parallel planes passed along the ESP while one plane passed across the ESP duct. The results show that electrohydrodynamic (EHD) secondary flow with relatively strong vortices exist in the ESP. The EHD secondary flow pattern depends on applied voltage and measuring plane position in respect to the spike tip. The strongest vortices occur in the plane passing through the tip of the upstream-directed spike. These relatively strong EHD vortices may hinder collection of the particles in the diameter range of 0.1–1 μm in the wide electrode spacing spike–plate ESPs.

Three-Dimensional Characterization of a Pure Thermal Plume

Pure thermal plumes have been investigated by two-dimensional (2D) and three-dimensional (3D) particle imaging velocimetry (PIV) techniques. While classical plume features have been checked out, time-dependent analysis allows one to clearly detect contraction and expulsion phases which are mainly driven by turbulent structure behavior. Balance of momentum equation demonstrates the link between stronger structures and expulsion-contraction motion mainly dominated by plume engulfment during contraction phases. A ratio of 3 between entrained mass flow rate during contraction and expulsion phases has been estimated. A new method, never previously applied to pure thermal plume, allows one to accurately characterize entrainment mechanism and for the first time, the latter renders it possible to estimate the entrainment coefficient all along the plume height, even close to the heating source. Moreover, entrainment coefficient is found to be 20% higher with direct method as opposed to the classical differential one widely used in the literature. Such a huge gap is found to be due to the fluctuating density and velocity part. Even through it markedly contributes to an enhanced entrainment mechanism, the role of fluctuation was generally overlooked in the previous works devoted to entrainment coefficient estimate.

Order and disorder in particle?liquid flows in a pipe

The spherical expanded polystyrene particle–oil two-phase flow in a vertical pipe was used to simulate the dispersed phase distribution in laminar bubbly flows. A three-dimensional particle image tracking technique was used to track the particles in the flow to study the ordered structure of dispersed phase distribution and its transition to disorder. The ordered structures behaved as particle strings aligned in the flow direction as induced by the flow shear. The structures were quite durable in high liquid velocity flows and dispersed gradually as the liquid velocity decreased. In lower velocity flows, the particles tended to form clusters in the horizontal direction, as predicted by potential theory for spherical bubbles rising in a quiescent inviscid liquid and as observed in experiments on non-shear bubbly water flows.