Three-dimensional Carbon Research Articles

3D Graphene-Like Carbon Structures from Poly(Acrylic Acid): A Novel Synthetic Route.

Emerging contaminants, such as the hormone 17α-ethynylestradiol (EE), in aquatic environments pose a serious risk to both human and environmental health, making efficient removal essential. This study evaluated the effectiveness of three-dimensional porous carbon structures derived from poly(acrylic acid) (PAAc, Carbopol 990) as adsorbents for removing EE from aqueous solutions. Activated carbon materials were prepared using varying ratios of KOH as an activating agent (PAAc : KOH; 1 : 0 AAC, 1 : 1 AC1, 1 : 2 AC2, and 1 : 3 AC3). Adsorption tests were conducted by adding 10 mg of the adsorbent to 40 mL of an EE solution (100 ppm, 20 % acetonitrile in water). Analyses including TGA, XRD, and Raman spectroscopy were performed to evaluate the materials' structural properties and adsorption capacities. Among the materials, AC3 exhibited the highest adsorption capacity for EE (238 mg g-1), followed by AC2 (153 mg g-1) and AC1 (82 mg g-1). The superior efficiency of AC3 can be attributed to its larger surface area and pore volume, enabling greater interaction with EE molecules. These materials demonstrated higher adsorption capacities compared to commercial activated carbons and single-walled carbon nanotubes. This work opens new possibilities for developing efficient adsorbents, contributing to more effective and sustainable solutions for water purification and environmental protection.

N-doped three-dimensional carbon nanosheets: Facile synthesis and high-concentration dye adsorption

Purification of dye-contaminated wastewater has always been a research hotspot, yet also a challenge, due to high concentration and species diversity of pollutants. The present study designs an efficient nitrogen-doped 3D carbon nanosheets (N-3DCNs) adsorbent with 2592.50 m2 g−1 of specific surface area and 2.68 m3/g of average pore volume based on nitrilotriacetic acid trisodium salt by combining calcination and activation techniques. Microstructure and surface potential of N-3DCNs indicate that a large number of N heteroatoms in the lattice of main material can effectively optimize Zeta potential from 1.53 to −31.08 mV with solution pH increases from 3 to 11. So, as-prepared N-3DCNs possesses necessary conditions for efficient and selective adsorption of cationic dyes due to the abundant adsorption sites and strong electrostatic interactions. When 700 mg/L of cationic rhodamine and anionic methyl orange are respectively used as high concentration industrial dye-contaminated wastewater, N-3DCNs shows 97.97 % and 89.13 % of removal efficiency within 60 min. Furthermore, the adsorption capacity of N-3DCNs displays a wider pH tolerance at 1000 mg/L of cationic concentration, with a maximum adsorption capacity of 4888.70 mg/g at pH = 7 and a minimum value of 4203.77 mg/g at pH = 3, only 14 % of attenuation rate. The kinetics mechanism of dye adsorption could be well explained by pseudo-second-order kinetic model, suggesting chemisorption behavior, while fitting better with the linear Langmuir isothermal model. The groundbreaking and exceptional adsorption performances of N-3DCNs can be attributed primarily to the high specific surface area and negatively charged active sites, facilitating synergistic adsorption.

Metallaphotocatalytic triple couplings for modular synthesis of elaborate N-trifluoroalkyl anilines

The integration of trifluoromethyl groups and three-dimensional quaternary carbon moieties into organic molecules has emerged as a prominent strategy in medicinal chemistry to augment drug efficacy. Although trifluoromethyl (hetero)aromatic amines and derivatives are prevalent frameworks in pharmaceuticals, the development of trifluoromethyl-embedded, intricately structured alkyl amine scaffolds for medicinal research remains a significant challenge. Herein, we present a metallaphotoredox multicomponent amination strategy employing 3,3,3-trifluoropropene, nitroarenes, tertiary alkylamines, and carboxylic acids. This synthetic pathway offers notable advantages, including the accessibility and cost-effectiveness of starting materials, high levels of chemo- and regioselectivity, and modularity. Furthermore, this approach enables the synthesis of a broad spectrum of aniline compounds featuring both trifluoromethyl group and distal quaternary carbon motifs along the aliphatic chains. The accelerated access to such elaborate N-trifluoroalkyl anilines likely involves three sequential radical-mediated coupling events, providing insightful implications for the retrosynthesis of potential compounds in organic synthesis and drug discovery.

Chromium Oxide Nanoparticles Anchored in Hydrogel-Derived Three-Dimensional N-Doped Porous Carbon Anode Materials as Lithium-Ion Batteries.

Transition metal oxides (TMOs) have been identified as the most promising anode materials for lithium-ion batteries (LIBs). However, these materials tend to undergo volumetric expansion during battery operation, which disrupts their internal structure and ultimately leads to a degradation of battery performance. Cr2O3/N-doped porous carbon (Cr2O3@NC) composites were successfully synthesized through high-temperature calcination using Cr2O3-containing hydrogels as precursors. The results show that the carbon material not only improves the electron transfer ability of Cr2O3 but also effectively prevents its agglomeration. The Cr2O3@CN composite as a novel anode material for LIBs exhibits a reversible capacity of 936 mAh g-1 after 200 cycles at a current density of 1 A g-1, showcasing excellent cycling and structural stability during cycling. Scanning electron microscopy analysis reveals that the Cr2O3@NC composite remains structurally intact throughout cycling. The innovative approach proposed in this study provides a new direction for the advancement of electrode materials for energy storage technologies.

FeN4S1 Single-Atom Sites Anchored on Three-Dimensional Porous Carbon for Highly Efficient and Durable Oxygen Electrocatalysis.

Precisely designing asymmetric active centers and exploring their electronic regulation effects to prepare efficient bifunctional single-atom catalysts (SACs) is important for boosting the practical applications of zinc-air batteries (ZABs). Herein, an effective strategy has been developed by introducing an axial S atom to the FeN4 active center, simultaneously assisted by pyrolyzing the graphene oxide (GO) sheathed zeolitic-imidazolate framework-8 (ZIF8) composite and constructing a three-dimensional (3D) porous framework with abundant FeN4S1 moieties. This structure can accelerate the oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) kinetics owing to the modulated electronic redistribution and d-band center with a reduced energy barrier. The optimal S-Fe-NC/rGO showcases a lower voltage gap (ΔE) of 0.64 V between both the ORR and OER half-wave potentials at 10 mA cm-2, highlighting the excellent bifunctional activities. The assembled S-Fe-NC/rGO rechargeable liquid ZABs deliver a power density of 154.05 mW·cm-2 and a desirable durability of >900 h. More importantly, the corresponding flexible solid-state ZABs exhibit considerable foldability.

(Fe, Co) oxide nanowires on gold nanoparticles modified MOF-derived carbon nanoflakes for high-efficiency sodium-ion batteries and supercapacitors across electrolytes

The three-dimensional conductive porous carbon nanosheets (CPCN) are from the bimetallic metal-organic framework (MOFs) consisting of organic ligating groups that incorporate zinc and cobalt ions deposited onto a flexible carbon cloth (CC). Utilizing a hydrothermal approach, iron-cobalt oxide (FCO) nanowires are intricately embedded onto CPCN modified with gold (Au), forming a flexible FCO/Au/CPCN@CC electrode. The electrochemical characteristics of electrodes are evaluated in 1 M Na2SO4, supercapacitor's storage capacity is tested at 4 V using 1 M NaPF6 electrolyte. Among its remarkable attributes are a peak energy density of 291.5 W h kg−1 achieved at a power density of 153.85 W kg−1, and even at the maximum power density of 1749.9 W kg−1, it maintains 144.78 W h kg−1. Undergoing 10,000 rounds of GCD, the equipment sustains a capacitance retention of 84.27 %. Moreover, the performance of the FCO/Au/CPCN@CC anode in sodium-ion batteries (SIBs) is assessed. At 0.1C, the discharge capacity reaches 958 mAh g−1, and there is almost no loss after the rate cycle. The Coulomb efficiency surpasses 98 % during 500 cycles at a large C-rate. The integration of Au nanoparticles onto the CPNC surface enhances the energy storage characteristic of the FCO/Au/CPCN@CC composite material in both battery and supercapacitor applications.

Dual-Steric Hindrance Modulation of Interface Electrochemistry for Potassium-Ion Batteries.

Electrolyte chemistry regulation is a feasible and effective approach to achieving a stable electrode-electrolyte interface. How to realize such regulation and establish the relationship between the liquid-phase electrolyte environment and solid-phase electrode remains a significant challenge, especially in solid electrolyte interphase (SEI) for metal-ion batteries. In this work, solvent/anion steric hindrance is regarded as an essential factor in exploring the electrolyte chemistry regulation on forming ether-based K+-dominated SEI interface through the cross-combination strategy. Theoretical calculation and experimental evidence have successfully indicated a general principle that the combination of increasing solvent steric hindrance with decreasing anion steric hindrance indeed prompts the construction of an ideal anion-rich sheath solvation structure and guarantees the cycling stability of antimony-based alloy electrode (Sb@3DC, Sb nanoparticles anchored in three-dimensional carbon). These confirm the critical role of electrolyte modulation based on molecular design in the formation of stable solid-liquid interfaces, particularly in electrochemical energy storage systems.

Green synthesis of SiOx/C-TiO2 with continuous conductive network towards enhancing lithium storage performance

High-capacity SiOx anodes face significant challenges in practical applications due to their low conductivity and high expansion rate. The combination of nanoengineering and carbon capping processes has been proven to address these issues. However, most carbon capping techniques cannot ensure uniform capping and fail to form a continuous conductive phase between active materials. This work proposes a green (solvent-free) and facile method for constructing SiOx/C-TiO2 (SCT@CN) nanocomposites by creating a three-dimensional carbon conductive network from gelatin-derived carbon and doping with titanium dioxide nanoparticles (TiO2 NPs). Comparison of TiO2 NPs with varying doping levels reveals that the synergistic effect between the conductive carbon network and TiO2 NPs enhances both the structural stability of batteries during charge/discharge cycles and the efficiency of active material utilization and lithium-ion diffusion. With the increase of TiO2 NPs, the capacity retention and ICE of the electrode improved, while the initial discharge capacity decreased. Notably, the SCT-2@CN electrode with 10 wt% TiO2 NPs exhibits the best electrochemical performance, with an initial coulombic efficiency (ICE) of 73.2 %. After 700 cycles at a high current density of 2.0 A g−1, it maintained a capacity of 503 mAh g−1, with a capacity retention rate of 81.86 %. The optimized carbon capping process and introduction of novel elements have the potential to enhance a range of energy storage materials.

Enhancing microbial fuel cell performance with free-standing three-dimensional N-doped porous carbon anodes

Microbial fuel cells (MFCs) utilize microorganisms as catalysts to transform the chemical energy to electrical power. However, the practical application of MFCs is currently impeded by low power output, which is caused by insufficient microbial colonization on the anode, slow extracellular electron transfer at the microbe-anode interface, and low oxygen reduction reaction catalytic efficiency at the cathode. Herein, a three-dimensional (3D) hierarchical porous anode of Carbonization-CTS-MF/rGOtempreture (CCMF/rGOT) by pyrolyzing crosslinked composite of melamine formaldehyde resin (MF), chitosan (CTS) and graphene oxide (GO). The macroporous anode provides a biocompatible surface for exoelectrogens and 3D electron transfer pathways. In addition, an appropriate balance of graphitic-N and pyrrolic-N content optimizes both conductivity and the number of active sites, thereby synergistically enhancing extracellular electron transfer (EET) efficiency. Therefore, the power density of CCMF/rGO1000 anode is 11.28 W/m3, which surpasses the CCMF1000 anode without 3D reduced graphene oxide (rGO) conductive network (10.04 W/m3), and traditional carbon cloth anode (4.36 W/m3). Moreover, the anode runs stably for more than 200 days with a maximum operating voltage of 0.69 V, which achieves chemical oxygen demand (COD) removal rate of 95.4 %. This work provides a promising strategy to prepare a free-standing 3D anode with enriched exoelectrogens and enhanced EET to improve the MFCs performance.

Ag@AgCl/carbon nitride/graphene oxide three-dimensional nanocomposite constructed for efficient removal of organic dyes by synergistic adsorption-photocatalysis

The efficient removal of dye pollutants from wastewater is a significant and hotspot research. In this manuscript, Ag@AgCl nanoparticles were anchored on three-dimensional carbon nitride/graphene oxide (CN/GO) using an in-situ photoreduction strategy, and thus a novel (Ag@AgCl/CN/GO) was achieved. The results showed that the Ag@AgCl/CN/GO was a highly efficient adsorption and photocatalytic material for the removal of dye pollutants. The maximum adsorption capacity of malachite green (MG), methylene blue (MB), rhodamine B (RhB) and crystal violet (CV) can be reached as 324, 216, 148 and 112 mg g−1, and the photocatalytic degradation rate were 95 %, 83 %, 76 % and 93 % under irradiation for 60 min, which were greatly higher than some comparisons reported. The improved visible light, enhanced absorption and electron transfer in the Ag@AgCl/CN/GO three-dimensional structure were responsible to the highly efficient removal of dyes. Furthermore, the Ag@AgCl/CN/GO showed a good reusability in the cycling test. The constructed nanocomposite will be attractive for removing pollutants in wastewater.

The synergistic effects on the magnetic CoNi and Fe3O4 nanoparticles co-embedded porous carbon toward enhanced microwave absorbing performance

Abstract Lightweight and environmentally friendly three-dimensional biomass-derived porous carbon (3D BPC) holds great potential as a highly effective material for microwave absorption (MA) applications. However, the high complex permittivity and lack of magnetic loss in a single 3D BPC lead to impedance mismatching and a limited absorption bandwidth. Developing 3D BPC–based absorbers with multiple loss mechanisms and excellent impedance matching remains a notable yet challenging task. In this study, inspired by a synergistic composition and microstructure design, 3D BPC co-embedded with magnetic cobalt–nickel (CoNi) and iron(III) oxide (Fe3O4) nanoparticles (3D BPC@CoNi@Fe3O4) was developed. 3D BPC@CoNi@Fe3O4 exhibited consistently low complex permittivity, primarily due to the suppression of conductive loss, whereas the introduction of magnetic phases (CoNi and Fe3O4) enhanced the magnetic loss. Optimised impedance matching, achieved through the synergistic regulation of the electromagnetic parameters, emerged as the key mechanism for improving the MA properties. The as-synthesised 3D BPC@CoNi@Fe3O4 composite, with only 20 wt.% loading demonstrated a wide effective absorption bandwidth (reflection loss [RL] < −10 dB) of 6.08 GHz and an impressive minimum RL value of −40.08 dB. These findings offer valuable insights into the development of high-performance 3D BPC–based microwave absorbers through composition and microstructure optimisation.

A novel RuP2-infused heteroatom-doped porous carbon for high-durability lithium-sulfur batteries

Nitrogen and phosphorus co-doped three-dimensional porous carbon encapsulated ruthenium diphosphide (PCS900@RuP2-2) is successfully synthesized via a phytic acid-assisted phosphating process. The resulting RuP2 nanoparticles, ranging in size from 10 to 50 nm, are encapsulated within a carbon matrix, providing a stable catalytic structure. Nitrogen adsorption and desorption tests reveal that PCS900@RuP2-2/S possesses a high specific surface area and a rich micro/mesoporous structure. This high porosity facilitates multi-directional ion diffusion and offers ample buffer space to accommodate sulfur volume expansion during cycling. Density functional theory (DFT) calculations confirm that PCS900@RuP2-2/S enables efficient adsorption of soluble polysulfides, thereby minimizing the notorious "shuttle effect." Electrochemical testing demonstrates the remarkable durability of PCS900@RuP2-2/S. After 500 cycles at a 1 C current density, the reversible capacity remains at 511.6 mAh g⁻¹, with an average capacity decay rate of just 0.047 % per cycle. Even under heavy sulfur loading conditions (4.2 mg cm⁻²), the composite maintains a high reversible capacity of 386.6 mAh g⁻¹ after 500 cycles. The combination of high porosity, stable catalytic structure, and efficient redox reaction facilitation contributes to the exceptional performance and longevity of PCS900@RuP2–2/S.

Ultralight Cellulose-Derived Carbon Nanofibers from Freeze-Drying Emulsion Towards Superior Microwave Absorption

Carbon nanofibers (CNFs) are usually prepared by the carbonization of cellulose aerogels obtained from freeze-drying. However, cellulose with low concentration (below 1 wt%) is required to maintain the good porosity of the aerogels due to the strong hydrogen bonding between the cellulose molecules. In order to address this problem, here, ultralight cellulose-derived CNFs have been fabricated by freeze-drying cyclohexane (CHE)/cellulose nanofiber emulsions and carbonization. Field emission scanning electron microscopy, Raman spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and Fourier transform infrared spectroscopy are used to characterize the resulting CNFs. It is found that the CNFs consist of three-dimensional carbon networks, whose microstructure is easily adjusted by changing the CHE ratio (from 0 to 25 vol%) in the emulsions. The CNFs with high porosity are attributed to the fact that CHE as the oil phase can effectively weaken the hydrogen bonding and reduce the aggregation of the cellulose nanofibers. Carbon lattice defects and residual oxygen-containing functional groups are regarded as polarization centers, leading to the enhancement of dielectric loss. The conductive carbon networks also improve the conductive loss. All these factors improve the microwave absorption performance of the CNFs. So, the produced CNFs exhibit a superior electromagnetic wave performance with a minimum reflection loss of −42.18 dB and effective absorption bandwidth up to 4.9 GHz at 2 mm with a filling ratio of 2 wt%. This work provides a simple, low-cost, and sustainable synthesis route for CNFs used for ultralight high-performance microwave absorption materials.

Metal-organic framework-derived in situ-grown Cu2Sb@NC octahedra for high-performance stable lithium/sodium storage

Intermetallic compounds are considered a special class of alloy-type anode materials that show great potential for use in lithium/sodium-ion batteries due to their inherent advantages, such as high specific capacity and enhanced safety features. However, their practical application is often impeded by the substantial volume changes that occur during the insertion and extraction of Li+/Na+ ions, leading to capacity decay and reduced service life. To address this challenge, we developed a novel composite material comprising Cu2Sb nanoparticles encapsulated within a N-doped octahedral carbon matrix (Cu2Sb@N-C). This composite structure features a heteroatom-doped conductive network, a three-dimensional carbon framework, and finely dispersed Cu2Sb nanoparticles. Benefiting from the heteroatom-doped conductive network, three-dimensional carbon framework and ultrafine Cu2Sb nanoparticles, they not only provide a penetrating network for the fast transfer of charge carriers and improve the accessibility of ions, but also alleviate the agglomeration and volume expansion of Cu2Sb during cycling. For LIBs, the material exhibited a reversible capacity of 1001.0 mAh/g after 330 cycles at 0.2 A/g, while maintaining a substantial capacity of 565.5 mAh/g after 1000 cycles at 1.0 A/g. In the case of SIBs, the material exhibited a capacity of 375.6 mAh/g after 100 cycles at 0.2 A/g. Post-cycling electrode analyses revealed that the Cu2Sb@N-C anode material retained its structural integrity, demonstrating its ability to withstand the continuous insertion and extraction of Li+/Na+ ions. This research contributes insights into the effective design of innovative high-capacity alloy-based anode materials for advanced secondary batteries.

Supermolecule-opitimized defect engineering of rich nitrogen-doped porous carbons for advanced zinc-ion hybrid capacitors.

Pitch-based porous carbons with adjustable surface chemical property and controllable pore structure are regarded as promising cathode materials for aqueous zinc-ion hybrid capacitors (ZIHCs), while its disordered carbon matrix and microstructure as well as insufficient surface defects often result in low Zn2+-storage capacity and poor rate capability of ZIHCs. Herein, a synergetic strategy of self-assembled supermolecule and enriched defective carbon engineering was developed to achieve ultrahigh edge-nitrogen doping for ZIHCs. The crystallite defects and surface structure of porous carbon could be effectively achieved through grafting electronegative oxygen-containing small molecules and high-level nitrogen-containing functional groups between modified polycyclic aromatic hydrocarbon and supermolecule framework. The optimized three-dimensional carbon structure delivered high capacity of 218 mAh g-1 at 0.2 A g-1, fast charge/discharge capability, enhanced energy density (165.4 Wh kg-1) and superior cycling stability (95% retention after 10000 cycles as cathode of ZIHCs). This provided new insight into the controllable synthesis of carbon cathodes for ZIHCs and expects to prepare functional porous carbon by supermolecules and special precursors.

Highly efficient nitrogen-doped three-dimensional interconnected porous carbon supported heterogeneous Co/MnO nanoparticles oxygen electrocatalysts for rechargeable zinc air batteries

Rechargeable zinc-air batteries (RZABs) show great promising in the current energy storage system because of their high energy density, low cost and high safety. However, RZABs’ cycling performance is still unsatisfactory due to the sluggish oxygen reduction and oxygen evolution reaction kinetics of air electrode. Transition Metal Oxides (TMOs) are considered to be highly promising oxygen reduction reaction (ORR) and oxygen evolution reaction (OER) catalysts for RZABs by high activity, robust stability and low cost. Here, the nitrogen-doped three-dimensional interconnected porous carbon supported heterogeneous Co/MnO nanoparticles composite (Co/MnO-NCs) as the air cathode in RZAB is synthesized via annealing method. The NCs not only provide efficient electron transfer channels but also significantly increases the specific surface area of the catalyst, exposing more reaction sites. MnO can effectively facilitate charge transfer and accelerate the decomposition reactions. The heterogeneous Co/MnO interface provides efficient reaction sites for the ORR/OER. Electrochemical results show that the prepared Co/MnO-NCs composite not only exhibits excellent ORR/OER performance but also demonstrates good stability. Furthermore, RZABs assembled by Co/MnO-NCs air cathode exhibit high open circuit voltage, high specific capacity and durable cyclic stability. This strategy has broad versatility and can be generalized to other TMOs electrocatalysts for RZABs.

Incorporation of Mo2C nanoparticles to pollen-derived 3D porous carbon as electrocatalyst for high performance lithium-sulfur batteries

The practical application and development of lithium‑sulfur (LiS) batteries are limited by the slow redox reaction kinetics and shuttle effect of polysulfide lithium (LiPSs). To address these issues, three-dimensional porous carbon (PC, derived from rapeseed pollen) modified with molybdenum carbide (Mo2C) nanoparticles is prepared by a simple and environment-friendly method. On the one hand, the PC-Mo2C host material can facilitate the uniform loading of sulfur and reduce its volume expansion due to its porous carbon structure. On the other hand, it mitigates the shuttle effect by effective chemical adsorption of LiPSs to form strong physical confinement and catalyze the conversion of LiPSs via the aid of the decorated Mo2C nanoparticles. Density functional theoretical calculations also illustrate the Mo2C nanoparticles are capable of inhibiting the shuttle of LiPSs and further improving the cycling stability. The results show that the PC-Mo2C/S electrode exhibits excellent electrochemical performance with high cycle stability (fading rate of 0.066 % per cycle at 0.2C and 0.054 % per cycle at 1C) and outstanding rate capacity (623.2 mAh g−1 at 5C).

Biomass-based three-dimensional network porous carbon anodes derived from discontinuous activation for high performance Li-ion batteries

An approach of discontinuous activation and frozon-dry pretreatment toward a three-dimensional network porous carbon was proposed by using apple as the carbon source. The porous carbon, characterized by its high surface area and abundant porosity, was optimized through the manipulation of temperature and activator quantities during the activation process. The sample obtained by first calcining at 500 °C and then at 800 °C shows ultra-high rate electrochemical performance of over 900 mA h g−1 after 100 cycles and over 500 mA h g−1 after 500 cycles under the condition of charging and discharging current density of 0.2 A g−1 due to the high porosity. It is ascribed to the unique porous structure that can make the electrolyte and lithium ion transport and path short on the surface and inside the electrode material, further enhance its fast transport ability. The described approach represents an innovative and potentially impactful method for producing porous carbon electrodes with excellent electrochemical performance, particularly in the context of high-rate capability lithium-ion batteries.

Preparation of core-shell Si/C/graphene composite for high-performance lithium-ion battery anodes

One of the important objectives for the development of enhanced lithium-ion batteries is developing high-performance silicon-based anodes with durable operational capability. Herein, a three-dimensional graphene-decorated core-shell Si/C composite is fabricated by the in-situ polymerization of organic pyrrole molecule and pyrolysis process, in which the melamine formaldehyde resin is subtly used as three-dimensional porous framework to offer abundant loading area for the uniform dispersion of active silicon nanoparticles. Meanwhile, the core-shell structure deriving from polypyrrole in the composite can effectively buffer the volume change of silicon ingredient and avoid the direct contact with the electrolyte during the cycling process, leading to the improved structural stability and electrochemical performance. The outermost layer of graphene nanosheets is designed to enhance the electrical conductivity of the electrode. As a result, the synthesized Si/C/graphene composite exhibits a high capacity and excellent cycling performance. This work reveals that combining a three-dimensional carbon substrate with a core-shell structure might be a promising solution for anode materials with obvious volume transformation.

Highly thermally conductive and shape-stabilized phase change materials with desirable solar/electric-to-thermal conversion performance based on high-modulus graphite/PVA foam

The widespread utilization of phase change materials (PCMs) has been impeded by challenges such as leakage, low thermal/electrical conductivity, and inadequate light absorption. Although constructing interconnected three-dimensional (3D) carbon networks within PCMs can mitigate these issues, their complex and energy-intensive fabrication processes, coupled with insufficient mechanical strength causing significant leakage and collapse of liquefied PCMs under external loads or impacts, hinder their practical application. Herein, we present a novel approach for the preparation of 3D graphite/polyvinyl alcohol foam (GPF) through a simple vacuum foaming combined with air-drying method. The obtained GPF-5 exhibits impressive compression strength (4.46 MPa) and compression modulus (93.1 MPa) at low density of 0.30 g/cm3. Upon impregnation with polyethylene glycol (PEG), GPF-5/PEG exhibits notable mechanical strength (7.62 MPa), contributing to its thermal shape stability and resistance to leakage. Even when subjected to temperatures above the melting point of PEG under external loads, GPF-5/PEG maintains its original shape without any liquid leakage. Due to the efficient construction of 3D thermal conductivity pathways within GPF, GPF-5/PEG demonstrates a high thermal conductivity of up to 3.48 W/m K−1 with graphite contents of 21.1 wt%, representing an increase of 136 % and 1640 % compared to graphite/PEG (with equivalent graphite content) and pure PEG, respectively. Additionally, GPF-5/PEG displays high latent heat of melting (136.8 J/g) and superior thermal cycling stability. Moreover, GPF-5/PEG demonstrates high solar-to-thermal and electric-to-thermal energy conversion capabilities, highlighting their potential for diverse applications. The work offers a rational strategy for fabricating high-modulus carbon foam, which can be used for PCMs-based multi energy conversion and storage systems with high thermo-mechanical properties.