Sample Thickness Research Articles

The sound absorption properties of a double-leaf micro perforated panel (DL-MPP) made from a double-layered polypropylene material.

Micro-perforated panel sound absorbers are recognized as an alternative method for noise control, offering advantages over conventional porous absorbers. However, the sound absorption of a single micro-perforated panel (MPP) is limited in its ability to cover a broad range of frequencies, especially in the low-frequency region. Therefore, the primary focus of this study is to investigate the sound absorption performance of a double-leaf micro-perforated panel (DL-MPP) absorber, which aims to achieve high sound absorption across a wide frequency range. This study examines the impact of varying parameters, including perforation ratio, diameter of perforated holes, and air gap thickness, on the sound absorption characteristics of a polypropylene-based DL-MPP absorber. Polypropylene was used as the sound absorption material for this investigation. The DL-MPP absorber consists of two perforated panels installed parallel to a rigid back wall, with an air gap between them. To assess the sound absorption performance, a prototype of the DL-MPP absorber was fabricated and tested using a two-microphone impedance tube method following ASTM E1050 standard. The results demonstrate that the optimal sound absorption performance was achieved by designing the MPPs with a 1% perforation ratio, 1 mm diameter of perforated holes, and a 1 mm sample thickness.

Beam-hardening correction method for quantifying moisture content in cement paste based on X-ray radiography

The X-ray spectrum changes while traveling through specimen, and this phenomenon, known as the beam-hardening effect, breaks the linear relationship between the intensity variety on radiographs and material thickness. In the detection of water transport in cement-based materials, this effect leads to inaccurate results of the quantitative moisture distribution inside the sample, and it is difficult to eliminate this effect by gravimetric calibration. To solve this problem, this paper proposed a calibration strategy for the attenuation coefficient curve of cement-water two-phase specimens, and provided a heuristic mathematical model for fitting the 2D attenuation coefficient surface of cement paste specimens. The experiments showed that for zones close to saturation, beam-hardening leads to an overestimation of moisture content, while for a zone with a low water content, the X-ray radiography results without correction tend to underestimate it. After correction, the method showed a quantitative result close to that of the gravimetric method, and maintained a good stability in samples of different thickness.

High-energy-resolution off-resonant spectroscopy with self-seeded x-ray free-electron laser pulses.

This paper presents the implementation of high-energy-resolution off-resonant spectroscopy (HEROS) measurements using self-seeded x-ray free-electron laser (XFEL) pulses. This study systematically investigated XFEL conditions, including photon energy and accumulated shot numbers, to optimize the measurement efficiency for copper foil samples near the K-edge. The x-ray absorption spectra reconstructed using HEROS were compared with those derived from fluorescence-yield measurements. The HEROS-based spectra exhibited consistent line shapes independent of the sample thickness. The potential application of HEROS to high-temperature copper was also explored. HEROS offers distinct advantages including scan-free measurement of x-ray absorption spectra with reduced core-hole lifetime broadening and self-absorption effects. Using self-seeded XFEL pulses, HEROS facilitates single-shot-based pump-probe measurements to investigate the ultrafast dynamics in various materials and diverse conditions.

Impact Fracture Resistance of Fused Deposition Models from Polylactic Acid with Respect to Infill Density and Sample Thickness

Fused deposition modeling (FDM) is widely employed in prototyping due to its cost-effectiveness, speed, and ability to produce detailed and functional prototypes using a variety of materials. Simultaneously, consideration for the use of biodegradable polymers and a general reduction in their usage while enhancing the production of polymer-based products is at the forefront of sustainable practices and environmental consciousness. This study investigates the impact fracture resistance of FDM models fabricated from Polylactic Acid (PLA), examining the influence of infill density (50% and 100% infill) and sample thickness (2 mm, 3 mm, and 5 mm). Optical microscopy, FTIR spectroscopy, and SEM analysis of PLA filament and fractured FDM PLA surfaces in impacted samples were conducted to ascertain the influence of process parameters on impact damage and failure mechanisms. The results indicate that a 100% infill profile with a 2 mm thickness should be avoided due to unpredictable behavior under impact. Conversely, a 5 mm thickness demonstrates significantly higher durability in comparison to a 50% infill profile. Optimal impact strength is observed in samples with a 3 mm thickness, suggesting potential material savings with 50% infill without compromising mechanical properties. The findings contribute valuable insights for refining FDM parameters and advancing the understanding of material behaviors in sustainable manufacturing practices.

3D printed honeycomb bilayer structures based on polylactic acid as lightweight microwave absorbing materials

Abstract3D printed honeycomb structures constituted by neat polylactic acid (PLA) and conductive PLA (PLAc) with different cell sizes and thicknesses were manufactured through 3D printing technology based on material extrusion (MEX). These structures were arranged into bi‐layer honeycomb structures (BHS) for evaluation of the microwave absorbing properties at the X‐band (8.2–12.4 GHz) and Ku‐band (12.4–18 GHz) frequency ranges. The effects of cell size, sample thickness, layer thickness ratio and the nature of the top layer on the electromagnetic attenuation performance of BHS samples were investigated in terms of reflection loss (RL). The components geometric characteristics and the arrangement of the layers exerted great influence on the RL values and effective absorption bandwidth (EAB). Overall the bilayer structures with 5 mm total thickness presented the best EM response in terms of EAB and minimum RL, where the component with the larger cell size (7.7 mm), PLAc (1 mm) as the top layer and PLA (4 mm) as the bottom layer exhibited the best results with RL values of −41 dB and EAB of 9.5 GHz. The BHS system with 7.7 mm cell size was more efficient in Ku band frequency range, whereas that with 3.5 mm cell size gave better response in the X‐band frequency range. Therefore, RL values and EAB can be adjustable by modifying the building strategy of the printed parts, such as thickness of the sample, cell size and thickness distribution of the conductive and non‐conductive layers. The findings in this work show the importance of the building strategy to fabricate components with controllable BHS and improved properties for microwave absorption application.

Fly-scan high-throughput coded ptychographic microscopy via active micro-vibration and rolling-shutter distortion correction.

Recent advancements in ptychography have demonstrated the potential of coded ptychography (CP) for high-resolution optical imaging in a lensless configuration. However, CP suffers imaging throughput limitations due to scanning inefficiencies. To address this, we propose what we believe is a novel 'fly-scan' scanning strategy utilizing two eccentric rotating mass (ERM) vibration motors for high-throughput coded ptychographic microscopy. The intrinsic continuity of the 'fly-scan' technique effectively eliminates the scanning overhead typically encountered during data acquisition. Additionally, its randomized scanning trajectory considerably reduces periodic artifacts in image reconstruction. We also developed what we believe to be a novel rolling-shutter distortion correction algorithm to fix the rolling-shutter effects. We built up a low-cost, DIY-made prototype platform and validated our approach with various samples including a resolution target, a quantitative phase target, a thick potato sample and biospecimens. The reported platform may offer a cost-effective and turnkey solution for high-throughput bio-imaging.

Monte Carlo Simulation of Electron Interactions in an MeV-STEM for Thick Frozen Biological Sample Imaging

A variety of volume electron microscopy techniques have been developed to visualize thick biological samples. However, the resolution is limited by the sliced section thickness (>30–60 nm). To preserve biological samples in a hydrated state, cryo-focused ion beam scanning electron microscopy has been developed, providing nm resolutions. However, this method is time-consuming, requiring 15–20 h to image a 10 μm thick sample with an 8 nm slice thickness. There is a pressing need for a method that allows the rapid and efficient study of thick biological samples while maintaining nanoscale resolution. The remarkable ability of mega-electron-volt (MeV) electrons to penetrate thick biological samples, even exceeding 10 μm in thickness, while maintaining nanoscale resolution, positions MeV-STEM as a suitable microscopy tool for such applications. Our research delves into understanding the interactions between MeV electrons and frozen biological specimens through Monte Carlo simulations. Single elastic scattering, plural elastic scattering, single inelastic scattering, and plural inelastic scattering events have been simulated. The electron trajectories, the beam profile, and the intensity change of electrons in each category have been investigated. Additionally, the effects of the detector collection angle and the focal position of the electron beam were investigated. As electrons penetrated deeper into the specimen, single and plural elastic scattered electrons diminished, and plural inelastic scattered electrons became dominant, and the beam profile became wider. Even after 10 μm of the specimen, 42% of the MeV electrons were collected within 10 mrad. This confirms that MeV-STEM can be employed to study thick biological samples.

Fire retardation, compressive strength and durability analysis of concrete reinforced with novel plasters: An experimental, computational and statistical research

Concrete is an essential component of the construction industry, valued for its high compressive strength (CS) and durability. However, when exposed to extreme conditions like fire without protective structural elements, its physical integrity deteriorates rapidly, leading to significant alterations in its mechanical properties. This research aims to provide a potential solution to this issue by assessing the fire resistance of various concrete samples, including unplastered (UNP), roughly plastered (RP), and those with contemporary insulation plaster (CIP) substitutions, at different thicknesses. These samples are subjected to varying temperatures and exposure times within an oven, followed by CS testing. These temperature levels and time intervals correspond to 300 °C, 450 °C, and 600 °C, with the time range is restricted to 60, 90, and 120-min, respectively. The results indicate that an increase in sample thickness correlates with a reduction in concrete degradation at high temperatures. Moreover, the findings reveal that after 120-min of exposure at 600 °C, UNP, RP, and CIP-reinforced samples achieve CSs of 27.435 MPa, 27.74 MPa, and 30.28 MPa, respectively. Notably, the 3 cm CIP-reinforced sample exhibits a CS exceeding 30 MPa under the most extreme conditions. The research incorporates regression and computational fluid dynamics (CFD) analyses to complement the experimental investigation. The regression analysis suggests that CIP-reinforced samples can withstand temperatures up to 600 °C for approximately 173-min, while the study implies that they could endure temperatures as high as 861 °C during a 120-min exposure.

Analysis of stress state and crack initiation time around hard-brittle particles in nickel-based alloys by interface model

The finite element method was used to simulate the stress distribution around hard-brittle particles with different particle-matrix interface states in nickel-based alloy with different sample thicknesses under 760 ℃/357 MPa and 980 ℃/250 MPa. The cohesive interface model was used to simulate different particle-matrix interface states. The effects of particle-matrix interface states, geometric characteristics of particles, particle positions in the sample, matrix orientation, and other factors on stress distribution were summarized. Through a thorough analysis of the stress distribution surrounding the particles, the crack initiation time was calculated. The results showed that the maximum stress around the particles was greater when the interface was in completely de-bonded CD state (no binding force between particles and the matrix) compared to the completely bonded CB state (completely coherent between particle and matrix). Furthermore, when the interface was CD, the larger the aspect ratio of the particles, and the closer they were to the surface of the sample, the greater the maximum stress around the particles. When the interface stiffness was reduced (due to mismatch or damage), the stress distribution did not change significantly under high interface stiffness conditions. However, when the interface stiffness decreased to a certain extent, the maximum stress value rapidly increased. In addition, the stress concentration factor began to change when the ratio of sample thickness to particle size (ξ) was less than 5. When the interfacial bonding was weak (with low interface stiffness), the crack initiation time around particles with large aspect ratio decreased significantly with the decrease of interface stiffness. Compared with the condition of 760℃/357 MPa (the same ratio of load to yield strength at 980℃), the crack initiation time around the particle was shorter at 980℃/250 MPa, and the influence of particle geometric features was smaller.

Development of a flexible composite based on vulcanized silicon casting with bismuth oxide and characterization of its radiation shielding effectiveness in diagnostic X-ray energy range and medium gamma-ray energies

The study aims to develop a novel, lead-free, flexible and lightweight composite shielding material against ionizing radiation. For this, it was used bismuth oxide (Bi2O3) in RTV-2 silicon matrix. The shielding tests were carried out in both diagnostic X-ray energies and intermediate gamma-ray energy range of up to 662 keV to determine the radiation attenuation properties of this material in terms of attenuation ratio, half value layer, tenth value layer, mean free path and lead equivalency of samples in weight of 30%, 40%, 50% in Bi2O3. In the diagnostic X-ray energy range, half value layer, tenth value layer and lead equivalency (in mm Pb) of the produced samples were measured at 80 and 100 kVp narrow beam conditions according to the requirements of EN IEC 61331-1 standard. The results show that lead equivalent values of the produced novel sheets was measured to be 0.16 mm Pb, corresponding to a 6 mm thickness of the flexible sample when it contains 30% wt. Bi2O3 in RTV matrix. The experimental findings for durability and flexibility also indicated that this new RTV-based flexible, lead -free shielding composite can be used safely for especially for manufacturing aprons, garments and thyroid guards used in mammography, radiology, nuclear medicine and dental applications in practice.

Correlating pipe dimensions and success of local heat treatment: Developing nomograms to deduce heat treatment parameters

Local post-weld heat treatment (PWHT) is the only option for heat treating field welded joints. Quite often, the success of local PWHT in alleviating the residual stress and tempering the material within the soak band (SB) is dependent on the ability to achieve the required heat treatment temperature and maintain through-thickness temperature gradient (TTG) within the specified limits at the end of heating cycle, whence soaking begins. Field observations reveal the inadequacy of AWS D 10.10 specified parameters viz. rate of heating (ROH), heat band (HB) and insulation band width in not achieving the required TTG for certain pipe dimensions. Although prior works have attempted to address this issue by widening the HB, the capacity of the heating equipment often pose a limitation. In such cases, reducing ROH is a plausible alternative. With, no such prior studies seen in literature, an exhaustive finite-element analysis simulating the local PWHT on 81, SA106GrC pipe samples (diameter and thickness varied in 9 levels each) was performed, thrice. First as per AWS recommendations, second by halving the code deduced ROH and third by doubling the code deduced HB. The trend of important outcomes (TTG, power source rating and energy consumption) with great significance to the heat treatment industry were also compared and analysed. Two nomograms were developed to serve as a ready reckoner for field heat treater in not only assessing the adequacy of heat treatment parameters but also with possible alternatives in achieving the desired TTG using field-available power source.

Understanding the Internal Conversion Efficiency of BiVO4/SnO2 Photoanodes for Solar Water Splitting: An Experimental and Computational Analysis.

This work aims to understand the spin-coating growth process of BiVO4 photoanodes from a photon absorption and conversion perspective. BiVO4 layers with thicknesses ranging from 7 to 48 nm and the role of a thin (<5 nm) SnO2 hole-blocking layer have been studied. The internal absorbed photon-to-current efficiency (APCE) is found to be nonconstant, following a specific dependence of the internal charge separation and extraction on the increasing thickness. This APCE variation with BiVO4 thickness is key for precise computational simulation of light propagation in BiVO4 based on the transfer matrix method. Results are used for accurate incident photon-to-current efficiency (IPCE) prediction and will help in computational modeling of BiVO4 and other metal oxide photoanodes. This establishes a method to obtain the sample's thickness by knowing its IPCE, accounting for the change in the internal APCE conversion. Moreover, an improvement in fill factor and photogenerated voltage is attributed to the intermediate SnO2 hole-blocking layer, which was shown to have a negligible optical effect but to enhance charge separation and extraction for the lower energetic wavelengths. A Mott-Schottky analysis was used to confirm a photovoltage shift of 90 mV of the flat-band potential.

Investigation of Microstructures and Tensile Properties of 316L Stainless Steel Fabricated via Laser Powder Bed Fusion.

In this study, a thorough investigation of the microstructures and tensile properties of 316L stainless steel fabricated via laser powder bed fusion (L-PBF) was done. 316L stainless steel specimens with two different thicknesses of 1.5 mm and 4.0 mm fabricated under similar conditions were utilized. Microstructural characterization was performed using optical microscopy (OM) and scanning electron microscopy (SEM) equipped with electron backscatter diffraction (EBSD). Melt pools and cellular structures were observed using OM, whereas EBSD was utilized to obtain the grain size, grain boundary characteristics, and crystallographic texture. The 1.5 mm thick sample demonstrated a yield strength (YS) of 538.42 MPa, ultimate tensile strength (UTS) of 606.47 MPa, and elongation to failure of 69.88%, whereas the 4.0 mm thick sample had a YS of 551.21 MPa, UTS of 619.58 MPa, and elongation to failure of 73.66%. These results demonstrated a slight decrease in mechanical properties with decreasing thickness, with a 2.4% reduction in YS, 2.1% reduction in UTS, and 5.8% reduction in elongation to failure. In addition to other microstructural features, the cellular structures were observed to be the major contributors to the high mechanical properties. Using the inverse pole figure (IPF) maps, both thicknesses depicted a crystallographic texture of {001} <101> in their as-built state. However, when subjected to tensile loads, texture transitions to {111} <001> and {111} <011> were observed for the 1.5 mm and 4.0 mm samples, respectively. Additionally, EBSD analysis revealed the pre-existence of high-density dislocation networks and a high fraction of low-angle grain boundaries. Interestingly, twinning was observed, suggesting that the plastic deformation occurred through dislocation gliding and deformation twinning.

Optimization of Magnetic Dielectric Nanocomposites Obtained by Facile and Low-Cost Fabrication for Effective Absorption of Electromagnetic Waves

This work presents the synthesis of Fe3 O4 nanoparticles (FNPs) and nanocomposites (NCs) of FNPs and functionalized carbon nanotubes (CNTs) at varying weight ratios for application in 8–18 GHz electromagnetic waves (EMW) absorbers. Their dielectric, magnetic, and structural characteristics were also examined. To create the desired NCs, CNTs are first mixed with FNPs at various weight ratios. The magnetic properties of the samples were ascertained using a vibrating sample magnetometer, and the dielectric properties of all the samples were examined by a vector network analyzer at room temperature after the crystal structure of the samples was determined by X-ray diffraction, surface morphology, and elemental analysis by scanning electron microscopy, energy dispersive spectroscopy, and Fourier transform infrared spectroscopy. Fe3 O4 @CNTs NCs in six different weight ratios (NC1 -NC6 ) were prepared. Sample NC3 , with a thickness of 2.25 mm, exhibited the greatest loss in the X band, measuring -27.07 dB, out of all the samples. Additionally, the NC4 sample which has a thickness of 5.00 mm, had the best loss, which came in at -38.21 dB in the Ku band. A data-driven method developed for multi-parameter optimization was then used to find out the optimal ratio weight ratio and sample thickness based on the experimental data. Samples with minimum reflection loss -34.1 dB (-41.5 dB), and others with effective bandwidth coving 69.0 % (71.4 %) in the X band (Ku band) were obtained.

Surface Design of 3D-printed Polyether Ether Ketone for Abrasive Wear Resistance

The surface features of additively manufactured polymer parts differ compared to extruded polymer parts and decide their performance in terms of power transmission applications. Layer thickness is one of the important process parameters chosen based on the part complexity and production speed, influencing the surface features. The abrasive wear performance of high-performance polyether ether ketone (PEEK), which determines the performance of power transmission elements such as bearings and gears, is reported in this article. The layer thickness employed in fabrication, which varies from 0.1 mm to 0.35 mm, influences the surface roughness, real contact area, and hardness of the as-printed PEEK. The friction coefficient and wear resistance of a printed part are influenced by the layer thickness employed, indicating the need for a proper choice of layer thickness for power transmission applications. Samples printed with a layer height of 0.25 mm and higher exhibited an increase of friction coefficient and wear loss due to the weak surface integrity. The friction and wear characteristics of additive manufactured samples are compared with extruded samples. Wear debris accommodation in the grooves of the as-printed surfaces accelerates the wear due to three-body abrasion in high layer thickness samples. The micromechanisms of wear damage in different layer thickness samples are discussed. The observations indicate the strong influence of layer thickness and facilitate the selection of appropriate layer thickness for the required friction coefficient in a particular application.

Impact of filler and gelling catalyst/agent on properties of flexible polyurethane foam

AbstractIn this study, the physiomechanical properties of carboxymethylcellulose sodium salt (Na‐CMC salt) filler‐loaded foam and its impact on the wicking capacity of the foam were investigated in juxtaposition with the increasing tin concentration. According to the study's findings, standard unfilled foam demonstrated no wicking at all, while flexible PU foam filled with Na‐CMC salt, even with low porosity and subpar mechanical traits, displayed wicking heights of 4 mm, 3.4 mm, and 2.8 mm in test specimens of thicknesses of 6 mm, 8 mm, and 10 mm. Moreover, filled foam with a higher porosity level exhibited significantly better wicking heights of 11.4 mm, 10.8 mm, and 8.2 mm. The inclusion of CMC filler in the PU foam matrix is the reason for enhanced wicking property in foam. The sample thickness and wicking height trends are consistent among all foams; as foam sample thickness increases, wicking height progressively falls. The correlation between the foam's porosity value and the number of closed cell windows is confirmed by stereomicroscopy and the porosity values. According to this study, the infused filler's characteristics have a greater influence on the foam's wicking capacity than the foam's porosity. This study contributes significant insights into ongoing initiatives to enhance user experience, well‐being, and hygiene through innovative and meticulously designed new developed mattress foam using Na‐CMC as a filler.Highlights Co‐relation between concentration of tin and infused filler on wicking property. Standard unfilled foam demonstrated no wicking at all. Na‐CMC salt filled foam displayed wicking heights. After 15% increase in tin level, mechanical properties of foam degrade. Wicking depends on nature of infused filler and the foam's porosity.

Differential phase contrast (DPC) mapping electric fields: Optimising experimental conditions.

DPC in Scanning Transmission Electron Microscopy (STEM) is a valuable method for mapping the electric fields in semiconductor materials. However, optimising the experimental conditions can be challenging. In this paper, we test and compare critical experimental parameters, including the convergence angle, camera length, acceleration voltage, sample configuration, and orientation using a four-quadrant segmented detector and a Si specimen containing layers of different As concentrations. The DPC measurements show a roughly linear correlation with the estimated electric fields, until the field gets close to the detection limitation, which is ∼0.5mV/nm with a sample thickness of ∼145nm. These results can help inform which technique to use for different user cases: When the electric field at a planar junction is above ∼0.5mV/nm, DPC with a segmented detector is practical for electric field mapping. With a planar junction, the DPC signal-to-noise ratio can be increased by increasing the specimen thickness. However, for semiconductor devices with electric fields smaller than ∼0.5mV/nm, or for devices containing curved junctions, DPC is unreliable and techniques with higher sensitivity will need to be explored, such as 4D STEM using a pixelated detector.

Phase and Composition Engineering of Self-Intercalated 2D Metallic Tantalum Sulfide for Second-Harmonic Generation.

Self-intercalation in two-dimensional (2D) materials is significant, as it offers a versatile approach to modify material properties, enabling the creation of interesting functional materials, which is essential in advancing applications across various fields. Here, we define ic-2D materials as covalently bonded compounds that result from the self-intercalation of a metal into layered 2D compounds. However, precisely growing ic-2D materials with controllable phases and self-intercalation concentrations to fully exploit the applications in the ic-2D family remains a great challenge. Herein, we demonstrated the controlled synthesis of self-intercalated H-phase and T-phase Ta1+xS2 via a temperature-driven chemical vapor deposition (CVD) approach with a viable intercalation concentration spanning from 10% to 58%. Atomic-resolution scanning transmission electron microscopy-annular dark field imaging demonstrated that the self-intercalated Ta atoms occupy the octahedral vacancies located at the van der Waals gap. The nonperiodic Ta atoms break the centrosymmetry structure and Fermi surface properties of intrinsic TaS2. Therefore, ic-2D T-phase Ta1+xS2 consistently exhibit a spontaneous nonlinear optical (NLO) effect regardless of the sample thickness and self-intercalation concentrations. Our results propose an approach to activate the NLO response of centrosymmetric 2D materials, achieving the modulation of a wide range of optoelectronic properties via nonperiodic self-intercalation in the ic-2D family.

Conductive hydro drying of ripened papaya: optimization and product characterization.

This study addresses the product-process characterization of refractance window drying of ripened papaya, considering the abundant availability and underutilization of the perishable product. A statistical design approach with varied drying temperature, time and sample thickness has been adopted to characterize moisture content, total phenolic content, total flavonoid content, vitamin C, and 2,2-diphenyl-1-picrylhydrazyl (DPPH) radical scavenging activity. The model fitting, analysis of variance, and numerical optimization showed that the quadratic model was the most suitable model for the response variables. The optimum process parameters were attained at a drying temperature of 90°C, time 86.92min, and sample thickness of 2.93mm. The optimal responses were moisture content 2.81%, total phenolic content 305.58mg GAE/g, total flavonoid content 51.92mg QUE/g, DPPH radical scavenging activity 91.56% and vitamin C 219.88mg/100g. With such high essential nutrients, refractance window dried ripened papaya can be utilized for commercially viable value-added food products.

Magnetic anisotropy and ferromagnetic resonance in inhomogeneous demagnetizing fields near edges of thin magnetic films

Using local ferromagnetic resonance spectroscopy, we have studied the magnetic properties near edges of thin tangentially magnetized permalloy films, in which a well-defined uniaxial magnetic anisotropy was induced perpendicular to one of the edges. In the experiment, two samples with thicknesses of 90 and 300 nm and with slightly different compositions were examined. To explain the magnetization dynamics near edges, we propose a simple yet effective model of a film in the form of a rectangular prism, which yields the modified Kittel formula for the resonance frequency. In this formula, the locally averaged distance-dependent demagnetizing field that emerges near the edges is included as an additional uniaxial anisotropy term. The measurements reveal that at a certain distance from the edge, the resulting (apparent) anisotropy, determined from the angular dependencies of the resonance field, almost vanishes. Moreover, its easy axis reorients to become parallel to the edge. The model predictions agree well with these results, proving that the main resonance mode behavior near the film edges can be accurately described by introducing additional effective uniaxial anisotropy, provided the measuring area is relatively large. However, for the thick (300 nm) sample, additional precession modes are also observed. These modes distort the angular dependence of the main mode, thus demonstrating the limitations of the model.