Thermal Stability Research Articles

A novel flame retardant epoxy thermoset based on renewable honokiol and furfuryl alcohol

In this study, honokiol epoxy resin was directly functionalized by bio-based material honokiol, which was combined with furfuryl alcohol-derived flame retardant by Diels-Alder reaction to prepare bio-based epoxy cross-linking system. After curing with 4,4′-diaminodiphenyl methane, HE1/FP0.5/DDM (121.37 °C) offered higher glass transition temperature than EP/DDM (91.75 °C). Meanwhile, the HE1/FP0.5/DDM exhibited excellent thermal stability and flame retardancy compared to EP/DDM. The char residue of HE1/FP0.5/DDM was obviously increased from 12.8% (EP/DDM) to 35.6% at 700 °C. Notably, the HE1/FP0.5/DDM achieved a limiting oxygen index value of 37.4% and UL-94 V-0 rating. Cone calorimeter demonstrated that the peak heat release rate, total heat release and fire growth rate of HE1/FP0.5/DDM were 400.29 kW/m2, 33.45 MJ/m2 and 4.40 kW/m2·s, reduced by 57.47%, 63.39% and 41.1% compared with EP/DDM, respectively. The satisfactory flame retardancy and smoke suppression were attributed to the flame-retardant function of FP in the condensed and gas phases. Thus, this work not only provided a simple but also eco-friendly approach to achieve flame retardant thermosets from honokiol to replace bisphenol A epoxy.

Physicochemical Properties of Lithium Bis(trifluoromethanesulfonyl)imide Solutions in Sulfolane

Abstract A study is performed of the physicochemical properties (ionic conductivity, viscosity, and density in the 30–50°C range of temperatures) and the electrochemical and thermal stability of lithium bis(trifluoromethanesulfonyl)imide solutions in sulfolane in the 0.001–1.89 M range of concentrations. It is shown that lithium bis(trifluoromethanesulfonyl)imide solutions in sulfolane exhibit high electrochemical stability (5.75 V vs. Li/Li+) and moderate ionic conductivity (2.75 × 10−3 Ω−1 cm−1 at 30°C for a 1 M solution), which are comparable to the respective parameters of sulfolane solutions of lithium hexafluorophosphate. The structure and transport properties of sulfolane solutions of lithium bis(trifluoromethanesulfonyl)imide are determined by their concentrations. In dilute solutions, lithium bis(trifluoromethanesulfonyl)imide is weakly associated. The degree of electrolytic dissociation of LiN(SO2CF3)2 initially falls and then rises upon an increase in its concentration. The electrolytic dissociation of lithium bis(trifluoromethanesulfonyl)imide rises along with its concentration, due to the formation of ion triplets and more complex ion associates. The constant of association and limit equivalent conductivity of LiN(SO2CF3)2 in sulfolane rise along with temperature, due to a drop in the degree of self-association and the degradation of the solvent’s structure. A specific feature of sulfolane solutions of lithium bis(trifluoromethanesulfonyl)imide is their tendency to form stable supercooled solutions.

Modulating Molecular Interaction of Zwitterion Toward Rational Interface Engineering of Perovskite Solar Cells

AbstractPassivation of perovskite crystals is a crucial strategy to improve the efficiency and stability of perovskite solar cells (PSCs). Zwitterions, which contain both positive and negative charges in the molecule, can be used to passivate perovskite crystals. However, these materials strongly interact with each other, resulting in extremely low solubility in common organic solvents. The low solubility of zwitterions hinders the formation of uniform films, which negatively affects perovskite crystal growth. In this study, a liquid‐type zwitterion (LTZ) is synthesized by modulating intermolecular interactions of the zwitterion (3‐(1‐Pyridinio)‐1‐propanesulfonate). By suppressing intermolecular interactions, the solubility and processibility of the zwitterion in common organic solvents are successfully improved. The well‐distributed LTZ‐treated films are obtained, resulting in better electrical properties for the PSCs compared to solid‐type zwitterion‐based devices. With these characteristics, the resulting device achieves a power conversion efficiency of 24.9% with excellent thermal stability (under 60 °C and N2 atmosphere), maintaining over 80% of its initial efficiency for 1968 h. In addition, the PSC module (active area of 32.7 cm2) achieves an improved efficiency of 19.86% with high open‐circuit voltage and fill factor. The results suggest that interface engineering with an LTZ has the potential to fabricate efficient and stable PSCs.

N-Guanylurea dinitramide: Optimal synthesis process, basic properties and spectroscopic data

N-Guanylurea dinitramide (GUDN), also known as FOX-12, is indeed a fascinating organic dinitramide salt with high insensitivity and good thermal stability. It shows great promise for use in next-generation insensitive munitions. In this study, GUDN was synthesized through the nitration reaction of ammonium sulfamate salt with an acid mixture (HNO3/H2SO4) and guanylurea salts in water. The optimal conditions for this synthesis have been determined, including reaction temperature at -40 oC, the nitration reaction time of 45 minutes, and specific molar ratios of the components, which include guanylurea sulfate, ammonium sulfamate, and the mixture of sulfuric and nitric acid. Additionally, various properties and spectral data of GUDN, such as FTIR, 1H-NMR, 13C-NMR, DSC-TG, XRD, and UV-Vis, have been thoroughly studied in the referenced article.

Curing characteristics and performance of a bio-based polyurethane engineered sealant with high bonding strength: Effect of R value and chain extender content

Polyurethane (PU) engineering sealants can be used to fill construction joints and pavement cracks with excellent practical results. However, traditional engineering sealants have the disadvantages of poor strength and raw materials that are not environmentally friendly. In this paper, a novel composition system of bio-based polyurethane engineering sealant was developed. The effects of the isocyanate/macroglycol molar ratio (nNCO/nOH, R value) for component A and the contents of amine chain extender (AME) on the curing characteristics and properties of the PU sealant were investigated using a series of experiments. Firstly, the curing process of the sealant was studied by Fourier transform infrared spectroscopy (FTIR) test, surface drying time test and gel time experiments. Secondly, the basic physical properties of the sealant were studied by tensile and hardness tests. And the water resistance of the sealant was judged. Then, the characteristics of molecular movement of polyurethane sealant were analyzed by dynamic mechanical analysis (DMA). The tensile cross-sections of the specimens were observed by scanning electron microscopy (SEM). Finally, the thermal stability of sealants was studied by thermogravimetric (TG) analysis. The results indicated that the material developed in this research can be used as a high-performance engineering sealant in actual projects. The increase in the R value and the decrease in AME content resulted in a longer curing process of the sealant. The rise of R value and AME content was able to raise the tensile strength, bonding strength and hardness of the sealant. The water resistance of the sealant was better. Also, the glass transition temperature (Tg) and storage modulus could also be increased and the thermal stability of the previous stage could be reduced by increasing the R value and AME content. Considering both the performance and construction requirements, the optimum R value and AME contents are recommended to be 2.1 and 1.4%, respectively.

Thermal Stability Analysis of Formamidinium–Cesium‐Based Lead Halide Perovskite Solar Cells Fabricated under Air Ambient Conditions

The instability of perovskite solar cells (PSCs) remains a major bottleneck for their commercialization, with thermal instability posing a major concern, given the inevitable presence of heat in photovoltaic devices. Mixed‐cation/halide perovskites demonstrate enhanced stability and efficiency compared to single‐cation/halide perovskites. Identifying the optimal perovskite composition capable of withstanding high temperatures for longer durations is crucial for the development of thermally stable PSCs. This study provides valuable insights into the optimization of mixed‐cation/halide perovskites to enhance the thermal and structural stability of perovskite films. By systematically varying the Cs content in FA1−yCsyPb(I0.85Br0.15)3 (0 < y < 25)‐based perovskite, it is observed that controlling the Cs content allows precise modulation of crystal orientation in perovskite film with 10% Cs obtained as the optimal value. The perovskite film containing 10% Cs not only exhibits reduced microstrain but also demonstrates enhanced thermal stability during testing at 85 °C under controlled humidity. Furthermore, planar PSCs are fabricated using FA0.90Cs0.10Pb(I0.85Br0.15)3 as the absorber layer and TOP‐3 as the hole‐transporting material, achieving a promising power conversion efficiency (PCE) of 17.70%. Impressively, the unencapsulated devices retain 95% of their initial PCE after 1000 h of dark storage under ambient conditions.

Giant Spin-Orbit Torque in Antiferromagnetic-Coupled Pt/[Co/Gd]N Multilayers with Suppressed Spin Dephasing and Robust Thermal Stability.

Manipulating magnetization via power-efficient spin-orbit torque (SOT) has garnered significant attention in the field of spin-based memory and logic devices. However, the damping-like SOT efficiency (ξDL) in heavy metal (HM)/ferromagnetic metal (FM) bilayers is relatively small due to the strong spin dephasing accompanied by additional spin polarization decay. Furthermore, the perpendicular magnetic anisotropy (PMA) originating from the HM/FM interface is constrained by the thickness of FM, which is unfavorable for thermal stability in practical applications. Consequently, it is valuable to develop systems that not only exhibit large ξDL but also balance thermal stability. In this work, we designed antiferromagnetic-coupled [Co/Gd]N multilayers, where staggered Co and Gd magnetic moments effectively suppress the spin dephasing and additional spin polarization decay. The ordered Co-Gd arrangements along the out-of-plane direction provide bulk PMA, endowing Pt/[Co/Gd]N high thermal stability. The SOT of Pt/[Co/Gd]N was systematically studied with N, demonstrating a significantly large ξDL of up to 0.66. The ξDL of Pt/[Co/Gd]N is greater than those of Pt/Co and Pt/ferrimagnetic alloys. This significant enhancement relies on the effective suppression of spin dephasing in [Co/Gd]N. Our work highlights that the antiferromagnetic-coupled [Co/Gd]N multilayer is a promising candidate for low-consumption and high-density spintronic devices.

Extraction, characterization, and utilization of mung bean starch as an edible coating material for papaya fruit shelf‐life enhancement

AbstractThis research was aimed to investigate the utilization of mung bean starch as an innovative edible coating material to enhance the shelf‐life of cut papaya fruits. The study focused on the extraction process of mung bean starch and its subsequent characterization through various analyses. Particle size (142.3 ± 1.24 nm), zeta potential (−25.52 ± 1.02 mV), morphological images, Fourier transform infrared (FTIR) spectra, and thermal stability (68.36 ± 0.15°C) were assessed to determine the mung bean starch properties. The functional properties, such as bulk density (0.51 ± 0.004 g/cm3) and tapped density (0.62 ± 0.010 g/cm3), angle of repose (21.61°), swelling power (12.26 ± 0.25%), and minimum gelation concentration (4.01 ± 1.25%), were examined to detect its potential as a coating base material. Subsequently, the prepared mung bean starch coating solution (1%, 2%, 3%, 4%, and 5%) was applied to papaya fruits and the coated fruits' physicochemical characteristics evaluated during storage. These characteristics encompassed color, weight loss, pH shifts, total soluble solids, titratable acidity, vitamin C content, fruit firmness, microbial analysis, and sensory attributes. The results revealed that starch coating on papaya maintained its color, reduced weight loss, preserved vitamin C, and delayed firmness loss, enhancing shelf‐life when compared to control sample. These findings demonstrated the effectiveness of mung bean starch coatings in preserving papaya fruits. The research made a significant contribution to the use of mung bean starch as a potential coating material for improving the shelf‐life of papaya fruits. This finding has great promise for the field of food preservation and quality control.

Twin Irida Graphene: A Carbon Material with Optoelectronic Features

AbstractA novel allotrope structure of carbon named twin irida graphene composed of 3‐16‐8 carbon rings is proposed. Its structural, mechanical, electronic, and optical characteristics are explored by density functional theory. It is shown that twin irida graphene has an energetically favorable structure. Its dynamical and thermal stabilities at room temperature are also examined and confirmed. The in‐plane stiffness of twin irida graphene is less than graphene. It is a metal and maintains this property even against the external strain and applied electric field. This sheet exhibits an anisotropy response to the incident photon with different polarizations. The potential of sheet for use in energy storage and absorption systems is indicated by its high dielectric constant and optical absorption. The reflection constants as well as the transmission constants of twin irida graphene indicate its transparency, mostly in the high‐energy region. Thus, twin irida graphene is a suitable material for use in optoelectronic applications due to its structural and physical characteristics.

A novel starch‐based composite hydrogel enhanced by activated charcoal from the banana peel for water decontamination

AbstractThe efficient removal of potential toxic elements (PTEs) from aqueous systems is an important challenge in water purification and industrial effluent treatment. Starch‐based hydrogels have shown promise in this context due to their unique properties, such as high absorption capacity and water retention. This work synthesized a novel hydrogel with and without activated charcoal (AC) from banana peel (5 wt.%) and trisodium citrate as a crosslinking agent and starch to remove PTEs. These hydrogels were characterized by Fourier‐transformed infrared (FTIR), scanning electron microscopy, TGA, XRD, water absorption, and zero‐charge point techniques. Subsequently, the affinity of AC, neat hydrogel, and the composite hydrogel for removing Cr6+, Cd2+, Ni2+, Mn2+, Zn2+, and Cu2+ in aqueous solution was evaluated. FTIR confirmed a crosslinking reaction between the starch molecules and the crosslinking agent (trisodium citrate). Besides, the addition of hydrogel+5%AC altered the crosslinking process. Adding AC to the hydrogel composite increased crystallinity, thermal stability, and porous size. The highest removal efficiency of neat hydrogel and hydrogel+5%AC was for Cr6+, obtaining 83.2% and 98.5%, respectively. As for the AC, the removal of Cu2+ was satisfactory, with 80.4%. Thus, hydrogel+5%AC proves to be a highly viable adsorbent for posttreatment of wastewater due to its ability to efficiently remove PTEs.

Optimization of preparation conditions and performance of a new degradable soil water retaining agent

Using polyaspartic acid (PAsp) and bentonite (BT) as the main raw materials, a new type of degradable soil water retaining agent (PAsp-AA/BT) was synthesized by microwave radiation. The optimum synthesis conditions and comprehensive properties of PAsp-AA/BT were discussed and the structure and surface characteristics of PAspsp-AA/BT were characterized by FTIR, SEM, XRD and TGA in the paper. The results showed that the optimum synthesis conditions of PAsp-AA/BT were as follows: the dosages of polyaspartic acid (PAsp), bentonite (BT), initiator potassium persulfate, crosslinking agent N,N′-methylene bisacrylamide was 5, 3, 0.3, 0.03%, respectively, the neutralization degree of acrylic acid was 75%, and the microwave power was 490W. Under this condition, the absorption ratio of the synthesized PAspsp-AA/BT in deionized water and 0.9% NaCl solution was 953 and 164 g/g, respectively. The synthesized PAsp-AA/BT had a high water absorption rate, good water retention and repeated water absorption, and the degradation rate in soil within 30 days reached 32.75%, with good degradation effect. The analysis of SEM, FT-IR, XRD and TGA showed that: the surface of PAsp-AA/BT was rough and had obvious pore structure, which was conducive to the diffusion of water molecules; polyaspartic acid, bentonite and acrylic acid were polymerized; the cross-linking structure was formed between polyaspartic acid, bentonite and acrylic acid; the product of PASP-AA/BT had good thermal stability. This study provides a new soil water retaining agent, which is helpful for the better development of soil water retaining agent research.

Diaminodiphenylmethane modified zirconium phosphate: A new strategy for trace addition to improve flame retardancy, smoke inhibition, and compatibility of epoxy resins

AbstractHigh‐efficient flame retardants (ZrP‐DDM) were synthesized successfully via ion‐exchange method, using diaminodiphenylmethane (DDM) modified layered zirconium phosphate (α‐ZrP). Trace addition of ZrP‐DDM in epoxy resins (EP) can enhance the flame‐retardant, smoke‐inhibition, mechanical, and thermal stability properties of EP composites. As shown in the results, ZrP‐DDM exhibits a better synergistic effect than α‐ZrP, and the EP composites containing 0.5 wt% ZrP‐DDM (EP/0.5ZrP‐DDM) show excellent flame‐retardant and smoke‐inhibition properties. Especially, EP/0.5ZrP‐DDM possesses a limiting oxygen index (LOI) of 33.7% with UL94 V‐1 rating, while the EP composites containing 0.5 wt% ZrP (EP/0.5ZrP) has a LOI of 30.1% and fails to achieve the UL94 rating. Furthermore, the peak heat release rate (PHRR), total heat release rate (THR), and smoke density rating of EP/0.5ZrP‐DDM decrease by 10.2%, 3.7%, and 8.2% compared with EP/0.5ZrP. Based on condensed‐phase product analysis, EP/ZrP‐DDM sample provides a gas source for intumescent char layer, and produces a stable phosphorus‐rich crosslinking structures during combustion, thus decreasing the fire hazard of the composite material. Meanwhile, the introduction of ZrP‐DDM has a less impact on tensile strength of EP composites compared with α‐ZrP, suggesting the addition of ZrP‐DDM effectively enhances the compatibility with the EP matrix, thereby maintaining excellent mechanical properties of the EP matrix.

Enhanced polyacrylamide polymer hydrogels using nanomaterials for water shutoff: Morphology, thermal and rheological investigations at high temperatures and salinity

This study focuses on the synthesis, characterization, and performance evaluation of polyacrylamide (PAM)/polyethyleneimine (PEI) hydrogels enhanced with nanomaterials for potential application in conformance control in oil wells. The materials used include PAM with a molar mass of 25,000 Kg mol−1, PEI with an average weight molar mass of 25 Kg mol−1, and synthetic brine (ionic strength 0.6). Nanomaterials such as titanium dioxide (TiO2) nanoparticles, oxidized carbon nanotubes (CNT-ox), and graphene oxide (GO) were incorporated into the hydrogel matrix. A simple method was used for the incorporation of nanomaterials into the polymeric matrix, ensuring their good dispersion in the hydrogels formed. Characterization techniques including thermogravimetric analysis (TGA), Fourier-transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM), and scanning electron microscopy (SEM) were employed to analyze the structure, morphology, and thermal stability of the hydrogels. Rheological measurements and gel strength evaluations were conducted to assess the performance of the hydrogels. Results indicate that the incorporation of nanomaterials enhanced the thermal stability, gel strength (Sydansk code), and resistance to syneresis of the hydrogels. Specifically, the addition of TiO2 nanoparticles exhibited the highest improvement in viscosity and thermal stability, attributed to strong interactions between TiO2 and PAM molecules. A notable decrease in syneresis percentages was observed with the inclusion of nanomaterials compared to the PAM reference sample, reaching 70.1 % for the hydrogel modified with GO. These findings suggest that nanomaterial-enhanced hydrogels hold promise for applications in conformance control in oil wells, offering improved stability and performance over extended periods of use.

Synthesis of Styrylbenzazole Photoswitches and Evaluation of their Photochemical Properties.

Styrylbenzazoles form a promising yet under-represented class of photoswitches that can perform a light-driven E-Z isomerization of the central alkene double bond without undergoing irreversible photocyclization, typical of the parent stilbene. In this work, we report the synthesis and photochemical study of 23 styrylbenzazole photoswitches. Their thermal stabilities, quantum yields, maximum absorption wavelengths and photostationary state (PSS) distributions can be tuned by changing the benzazole heterocycle and the substitution pattern on the aryl ring. In particular, we found that push-pull systems show large redshifts of the maximum absorption wavelengths and the highest quantum yields, whereas ortho-substituted styrylbenzazole photoswitches exhibit the most favorable PSS ratios. Taking advantage of both design principles, we produced 2,6-dimethyl-4-(dimethylamino)-styrylbenzothiazole, a thermally stable and efficient P-type photoswitch which displays negative photochromism upon irradiation with visible light up to 470 nm to obtain a near-quantitative isomerization with a very high quantum yield of 59%. Furthermore, 4-hydroxystyrylbenzothiazole was demonstrated to be a pH-sensitive switch which exhibits a 100 nm redshift upon deprotonation. Ortho-methylation of this switch improved the obtained PSS ratio in its deprotonated state from E:Z=53:47 to E:Z=18:82. We anticipate that this relatively unexplored class of photoswitches will form a valuable expansion of the current family of photoswitches.

Dihydroartemisinin-driven TOM70 inhibition leads to mitochondrial destabilization to induce pyroptosis against lung cancer.

Enhancement of malignant cell immunogenicity to relieve immunosuppression of lung cancer microenvironment is essential in lung cancer treatment. In previous study, we have demonstrated that dihydroartemisinin (DHA), a kind of phytopharmaceutical, is effective in inhibiting lung cancer cells and boosting their immunogenicity, while the initial target of DHA's intracellular action is poorly understood. The present in-depth analysis aims to reveal the influence of DHA on the highly expressed TOM70 in the mitochondrial membrane of lung cancer. The affinity of DHA and TOM70 was analyzed by microscale thermophoresis (MST), pronase stability, and thermal stability. The functions and underlying mechanism were investigated using western blots, qRT-PCR, flow cytometry, and rescue experiments. TOM70 inhibition resulted in mtDNA damage and translocation to the cytoplasm from mitochondria due to the disruption of mitochondrial homeostasis. Further ex and in vivo findings also showed that the cGAS/STING/NLRP3 signaling pathway was activated by mtDNA and thereby malignant cells underwent pyroptosis, leading to enhanced immunogenicity of lung cancer cells in the presence of DHA. Nevertheless, DHA-induced mtDNA translocation and cGAS/STING/NLRP3 mobilization were synchronously attenuated when TOM70 was replenished. Finally, DHA was demonstrated to possess potent anti-lung cancer efficacy in vitro and in vivo. Taken together, these data confirm that TOM70 is an important target for DHA to disturb mitochondria homeostasis, which further activates STING and arouses pyroptosis to strengthen immunogenicity against lung cancer thereupon. The present study provides vital clues for phytomedicine-mediated anti-tumor therapy.

Preparation and Properties of Attapulgite-Hydroxyethyl Cellulose Composite Poly (Acrylic Acid-co-2-acrylamide-2-methylpropanesulfonic Acid) Concrete Internal Curing Material

Attapulgite-hydroxyethyl cellulose-poly (acrylic acid-co-2-acrylamide-2-methylpropanesulfonic acid) (ATP-HEC-P(AA-co-AMPS)) in-concrete curing material was synthesized by aqueous solution polymerization using attapulgite (ATP) as an inorganic filler and hydroxyethyl cellulose (HEC) as a backbone. The effects of relevant factors such as ATP dosage, HEC dosage, degree of neutralization, initiator quality, and cross-linking agent quality on the water absorption characteristics of ATP-HEC-P (AA-co-AMPS) were investigated through expansion tests. The micro-morphology of ATP-HEC-P (AA-co-AMPS) was also comprehensively characterized using Fourier transform infrared spectroscopy, scanning electron microscopy, a thermal analysis, and other applicable means. The results showed that the prepared ATP-HEC-P (AA-co-AMPS) had a strong water absorption and water retention capacity, with a water absorption multiplicity of 382 g/g in deionized water and 21.55% water retention capacity after being placed at room temperature for 7 d in a bare environment. Additionally, ATP-HEC-P (AA-co-AMPS) showed good performance for absorbing liquids within the pH range of 7–12. The material’s thermal stability and mechanical properties were also significantly improved after the addition of ATP. The preparation cost is low, the process is simple, and the material meets the requirements for concrete curing materials.

Coordination assembly and NIR photothermal conversion of Metal-organic framework based on 5-(2-cyanophenoxy) isophthalic acid

The development of new photothermal conversion materials in the field of metal-organic frameworks (MOFs) shows broad prospects, but their design synthesis and proper mechanism analysis are still full of huge challenge. Here, four novel MOFs were constructed with 5-(2-cyanophenoxy) isophthalic acid, {Ni(2-CB-IPA)(bpp)(H2O)}n (1), {Ni2(2-CB-IPA)2(bpa)2(H2O)2}n (2), {Co(2-CB-IPA)(bpp)}n (3), {Mn2(2-CB-IPA)2 (bpp)(H2O)2}n (4). (Where 2-CB-IPA = 5-(2-cyanophenoxy) isophthalic acid, bpa = 1,2-bis(4-pyridine)-ethane; and bpp = 1,3-bis(4-pyridyl)propane). The absorption peak at 730 nm in the near-infrared region indicates that different charge transfer interactions affect the photothermal conversion ability. Under laser irradiation (730 nm, 0.45 W cm−2), such compounds exhibit different and distinct warming processes (1 from 20.8 to 91.8 °C; 2 from 20.1 °C to 86.2 °C; 3 from 20.6 to 77.1 °C) except for compound 4. The excellent crystallinity of these materials after irradiation demonstrates excellent thermal stability and cycling durability. Subsequently, further research on the structure-activity relationship revealed that strong π - π interactions are also the reason for the excellent performance of NIR photothermal conversion of 1 under the premise of high NIR absorption. This work provides a visual platform for the photothermal phenomena of crystalline materials.

Effect of different BaO contents on the photoluminescence properties of the Eu2+-doped high thermal stability Sr3−xBaxMgSi2O8 phosphors

In this study, 0.015 Eu[Formula: see text]-doped Sr[Formula: see text]BaxMgSi2O8 ([Formula: see text], 0.3, 0.6, 0.9) were used as compositions to find the effect of BaO content on their photoluminescence excitation (PLE) and photoluminescence emission (PL) properties. They were sintered at 1400°C in a reduction atmosphere of 95% N[Formula: see text]% H2 to form blue phosphors. X-ray diffraction pattern and SEM observation were used to analyze their crystal properties, and a fluorescence spectrophotometer was used to analyze their PLE and PL properties. After conducting a thorough analysis, our research primarily encompasses four significant research themes. First, SEM observations revealed that synthesized Eu[Formula: see text]-doped Sr[Formula: see text]BaxMgSi2O8 phosphors exhibit the formation of whisker-like structures. Therefore, the whisker-like structures in all the Eu[Formula: see text]-doped Sr[Formula: see text]BaxMgSi2O8 phosphors were analyzed using the HRTEM and its equipped EDS to find how BaO content influenced both the quantity and fineness of these whiskers. Second, we examined the impact of BaO content on the PLE and PL emission intensities of the Eu[Formula: see text]-doped Sr[Formula: see text]BaxMgSi2O8 phosphors across a temperature range from room temperature to 210°C. This investigation aimed to uncover the effects of BaO content and temperature on the thermal stability of the Eu[Formula: see text]-doped Sr[Formula: see text]BaxMgSi2O8 phosphors. Lastly, our fourth important investigation involved reorganizing the PLE spectra of the Eu[Formula: see text]-doped Sr[Formula: see text]BaxMgSi2O8 phosphors with the energy band as the x-axis. The Gaussian fitting function was applied to analyze the excitation spectra and discern the influence of BaO content on the value of the Stokes shift.

Weakening Mn-O Bond Strength in Mn-Based Perovskite Catalysts to Enhance Propane Catalytic Combustion.

Exploring highly efficient and robust non-noble metal catalysts for VOC abatement is crucial but challenging. Mn-based perovskites are a class of redox catalysts with good thermal stability, but their activity in the catalytic combustion of light alkanes is insufficient. In this work, we modulated the Mn-O bond strength in a Mn-based perovskite via defect engineering, over which the catalytic activity of propane combustion was significantly enhanced. It demonstrates that the oxygen vacancy concentration and the Mn-O bond strength can be efficiently modulated by finely tuning the Ni content in SmNixMn1-xO3 perovskite catalysts (SNxM1-x), which in turn can enhance the redox ability and generate more active oxygen species. The SN0.10M0.90 catalyst with the lowest Mn-O bond strength exhibits the lowest apparent activation energy, over which the propane conversion rate increases by 3.6 times compared to that on the SmMnO3 perovskite catalyst (SM). In addition, a SN0.10M0.90/cordierite monolithic catalyst can also exhibit a remarkable catalytic performance and deliver excellent long-term durability (1000 h), indicating broad prospects in industrial applications. Moreover, the promotional effect of Ni substitution was further unveiled by density functional theory (DFT) calculations. This work brings a favorable guidance for the exploration of highly efficient perovskite catalysts for light alkane elimination.

Alkaliphilic and thermostable lipase production by leaf litter fungus Leptosphaerulina trifolii A SMR-2011.

Fungi that inhabit fire-prone forests have to be adapted to harsh conditions and fungi affiliated to Ascomycota recovered from foliar litter samples were used for bioprospecting of molecules such as enzymes. Agni's fungi isolated from leaf litter, whose spores are capable of tolerating 110 oC were screened for thermostable lipases. One of the isolates, Leptosphaerulina trifolii A SMR-2011exhibited high positive lipase activity than other isolates while screening through agar plate assay using Tween 20 in the medium. Maximum lipase activity (173.2 U/mg) of L. trifolii was observed at six days of inoculation and decreased thereafter. Among different oils used, the maximum lipase activity was attained by soybean oil (940.1 U/mg) followed by sunflower oil (917.1 U/mg), and then by mustard oil (884.8 U/mg), showing its specificity towards unsaturated fatty acids. Among the various organic nitrogen sources tested, soybean meal showed maximum lipase activity (985.4 U/mg). The partially purified enzyme was active over a wide range of pH from 8 to 12 with a pH optimum of 11.0 (728.1 U/mg) and a temperature range of 60-80 oC with an optimal temperature of 70 oC (779.1 U/mg). The results showed that lipase produced by L. trifolii is alkali stable and retained 85% of its activity at pH 11.0. This enzyme also showed high thermal stability retaining more than 50% of activity when incubated at 60 oC to 90°C for 2h. The ions Ca2+ and Mn2+ induced the lipase activity, while Cu2+ and Zn2+ ions lowered the activity compared to control. These results suggests that the leaf litter fungus L. trifolii serves as a potential source for the production of alkali-tolerant and thermostable lipase.